User's Manual

Installation manual: Oasis security system JA-80K - 2 - MKE55800
Contents:
1. CONTROL PANEL ARCHITECTURE................................................... 3
1.1. O PTIONAL SYSTEM CONFIGURATIONS ................................................ 4
2. INSTALLATION ..................................................................................... 4
2.1. P OWER INLET .................................................................................. 4
3. CONTROL PANEL MEMORY UNIT...................................................... 4
4. CONTROL PANEL CONNECTORS AND TERMINALS ...................... 4
5. WIRED KEYPAD CONNECTION .......................................................... 5
6. BACK-UP BATTERY ............................................................................. 5
7. POWERING-UP THE CONTROL PANEL FOR THE FIRST TIME....... 6
7.1. W IRELESS KEYPAD ENROLLMENT ...................................................... 6
8. LANGUAGE SELECTION OF THE KEYPAD....................................... 6
9. RESETTING THE CONTROL PANEL .................................................. 6
10. CLOSING THE CONTROL PANEL COVER .................................... 6
11. ENROLLING WIRELESS DEVICES................................................. 6
11.1. I NSTALLING WIRELESS DEVICES ......................................................... 6
11.2. E NROLLING WIRELESS DEVICES TO THE CONTROL PANEL .................... 6
11.3. T ESTING ENROLLED DEVICES ............................................................ 7
11.4. M EASURING SIGNAL STRENGTH ......................................................... 7
11.5. E RASING ENROLLED DEVICES ............................................................ 7
11.6. E NROLLING THE CONTROL PANEL TO UC AND AC MODULES ................ 7
12. CONTROL PANEL PROGRAMMING .............................................. 8
12.1. C ONTROL PANEL PROGRAMMING SEQUENCES .................................... 8
12.2. E XIT DELAY TIME ............................................................................ 10
12.3. E NTRANCE DELAY TIME ................................................................... 10
12.4. A LARM DURATION TIME ................................................................... 11
12.5. PGX AND PGY FUNCTIONS ............................................................ 11
12.6. C HANGING TELEPHONE NUMBERS IN MAINTENANCE MODE ................. 11
12.7. R ADIO INTERFERENCE INDICATION ................................................... 11
12.8. R ADIO COMMUNICATIONS SUPERVISION ........................................... 11
12.9. RESET ENABLED .......................................................................... 11
12.10. E NROLLMENT TO A SUB CONTROL PANEL FOR SETTING ( ARMING )
CONTROL 11
12.11. M ASTER CODE RESET ................................................................ 12
12.12. C ONTROL PANEL ENROLLMENT TO UC OR AC MODULES OR TO A SUB
CONTROL PANEL 12
12.13. S ETTING (A RMING ) WITHOUT AN ACCESS CODE ........................... 12
12.14. T RIGGERED - DETECTOR INDICATION ............................................ 12
12.15. C ONFIRMATION OF INTRUDER ALARMS ........................................ 12
12.16. E XIT DELAY BEEPS ..................................................................... 12
12.17. E XIT DELAY BEEPS WHILE PARTIALLY SETTING ( ARMING )............... 13
12.18. E NTRANCE DELAY BEEPS ........................................................... 13
12.19. S ETTING ( ARMING ) CONFIRMATION BY WIRED - SIREN CHIRP ........... 13
12.20. S IRENS ALWAYS SOUND DURING AUDIBLE ALARMS ....................... 13
12.21. W IRELESS SIREN ALARM ENABLED (IW AND EW)......................... 13
12.22. A UTO - BYPASS USER APPROVAL VIA THE  KEY ............................... 13
12.23. F INAL - DOOR DETECTORS ........................................................... 13
12.24. P ARTIAL SETTING ( ARMING ) OR SYSTEM SPLITTING ...................... 14
12.25. A UTOMATIC SUMMER TIME ( DAYLIGHT SAVING TIME )..................... 14
12.26. T AMPER ALARM IN RESPONSE TO AN INCREASE IN THE NUMBER OF
TRIGGERED TAMPER SENSORS ................................................................................ 14
12.27. O PERATING THE PG OUTPUTS USING 8 AND 9 ............................. 14
12.28. P ERMANENT ALARM STATUS DISPLAY FOR A SET SYSTEM ............. 14
12.29. T AMPER ALARM IF UNSET ........................................................... 15
12.30. E NGINEER RESET ...................................................................... 15
12.31. R ECORDING PG OUTPUT ACTIVATION TO MEMORY ....................... 15
12.32. A NNUAL CHECK NOTIFICATION .................................................... 15
12.33. O NLY SINGLE ALARM INDICATION ................................................ 15
12.34. S ETTING ( ARMING ) BY SERVICE CODE ......................................... 15
12.35. A UDIBLE PANIC ALARM ............................................................... 15
12.36. H IGHER CONTROL - PANEL RECEIVER - SENSITIVITY ......................... 15
12.37. A CCESS BY CODE PLUS CARD ..................................................... 16
12.38. A UDIBLE 24 HOUR INTRUDER ALARM ........................................... 16
12.39. S ERVICE MODE ONLY WITH SERVICE CODE AND MASTER CODE ...... 16
12.40. D EVICE REACTIONS AND SECTION ASSIGNMENT ........................... 16
12.41. C ODE / CARD REACTIONS AND SECTION ASSIGNMENT .................... 17
12.42. E NROLLMENT BY KEYING IN PRODUCTION CODES ......................... 17
12.43. A UTOMATIC SETTING / UNSETTING SCHEDULE ............................... 17
12.44. C HANGING THE SERVICE CODE ................................................... 17
12.45. G O TO MAINTENANCE MODE ....................................................... 17
12.46. S ETTING THE INTERNAL CLOCK ................................................... 17
12.47. E DITING KEYPAD TEXT ............................................................... 18
13. OPERATING THE SYSTEM ........................................................... 18
13.1. T HE SYSTEM KEYPAD ..................................................................... 18
13.1.1. Keypad indicators: ............................................................. 18
13.1.2. LCD display........................................................................ 18
13.1.3. Keypad display sleep-mode .............................................. 18
13.1.4. Keys ................................................................................... 18
13.1.5. Functions beginning with the key ..................................... 19
13.2. P
ROGRAMMING ACCESS CODES AND CARDS ..................................... 19
13.2.1. Programming access codes and cards ............................. 19
13.3. S ETTING AND UNSETTING ( ARMING / DISARMING ) THE SYSTEM ............ 20
13.4. M AINTENANCE M ODE ..................................................................... 20
13.4.1. Displaying which user/card positions are occupied ...........20
13.4.2. Bypassing devices..............................................................20
13.4.3. Protecting a car near the system........................................20
14. OPERATING AND PROGRAMMING THE SYSTEM BY PC.........21
15. BASIC GUIDANCE FOR INSTALLERS..........................................21
16. TROUBLE-SHOOTING ....................................................................22
17. CONTROL PANEL TECHNICAL SPECIFICATIONS .....................22