User's Manual

Installation manual: OASiS security system JA-82KRC-US 21 / 21 MKH51400
connected to the Internet. For this remote access it is first
necessary to register at www.GSMLink.cz
15. Basic guidance for installers
1. Create an installation plan that sufficiently covers the building
to be protected.
2. If the customer requests changes to the suggested
configuration, especially reducing the number of detectors,
ask for his request to be given to you in writing to avoid future
disputes.
3. Perform the installation in a very professional and
conscientious manner and always tidy up the site
afterwards.
4. It is very important to teach the end user how to use and test
the system and to check his level of understanding.
5. Get the customer to sign a written statement that the system
was installed according to the customer’s specifications and
that the customer understands how to operate the system.
6. Explain the importance of the annual technical inspection of
the system and offer him this service. For more details see
the relevant EN standards.
16. Trouble-shooting
Problem Possible causes
Solutions
The control panel is not in service
mode after being powered up.
The control panel does not have factory-default settings. Reset the control panel.
It is impossible to enroll a wireless
device to the control panel.
The device’s location is unsuitable, the control panel antenna is
disconnected, the device’s battery was incorrectly installed, the
control panel is not in enrollment mode, the device is too near to
the control panel (it should be at least 2 meters away).
Check and fix it.
The keypad unit indicates a fault
Press the ? key to see the cause.
React according to the cause displayed.
A motion detector triggers false alarms
for no apparent reason.
Animals are moving in the protected area (mice etc), sudden
changes in temperature, significant air movements, movement of
objects having a temperature close to 37°C (e.g. curtains moving
above a radiator)
Change the location of the detector, select a higher
immunity in the detector, use an optional pet lens in
the detector, program alarms confirmed by two
detectors in the control panel.
The wireless keypad does not indicate
entrance delays by beeping.
If the keypad is only battery-powered, then it turns off 20
seconds after the last time a key was pressed. To indicate
entrance delays, first wake it up.
Install an ordinary magnetic sensor to the entrance
door, wiring it to the keypad input so that opening
the door wakes up the keypad and reports to the
control panel. Alternatively, power the keypad with
an AC adaptor to prevent sleep mode or install an
indoor wireless siren type JA-80L to generate
entrance delay beeps.
17. Control panel technical specifications
Power supply 110 V / 60 Hz, max 0.1 A, CLASS PROTECTION II
Backup-battery 12 V, 2.2 Ah, typical battery lifetime approx. 5 years
Backup power output maximum continuous load 0.4 A, intermittent load 1 A for 15 min’s max.
Number of wireless device addresses 50 (requires a JA-82R module)
Number of hard-wired inputs 4 (or 14 if a JA-82C is plugged in), double balanced inputs, with triggering and tamper functions,
programmable section assignment and reactions
External warning output EW* switching to GND, max. 0.5A
Internal warning output IW* switching to GND, max. 0.5A
Programmable outputs* PGX, PGY max. 0.1 A, switching to GND, programmable function
Event memory 255 latest events, including date and time stamping
Communications frequency (JA-82R) 868 MHz
Security grade 2 according to EN 50131-1, EN 50131-6, and EN 50131-5-3
Operating environment II. internal (-10 to +40°C) - compliant with EN 50131-1
Radio emissions ETSI EN 300220
EMC EN 50130-4,EN 55022
Electrical safety EN 60950-1
Can be operated according to ERC REC 70-03
* these signals are also transmitted wirelessly to AC and UC receiver modules.
Jablotron Ltd. hereby declares that the JA-82KRC “OASiS“ control panel is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The original of the conformity assessment can be found on the web site www.jablotron.com, Technical
Support section.
Jablotron Ltd. hereby declares that the product complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user’s authority to operate the equipment.
Note: Dispose of batteries safely depending on battery type and local regulations. Although this product does not contain any harmful
materials we suggest you return the product to the dealer or directly to the manufacturer after use.
Internet: www.jab lotron.c om
Tel.: [phone]
fax: [phone]
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czec h Republic