User's Manual

The JA-80P mini-size wireless motion detector 1 / 1 MHP52700_PTS_FCC
The JA-85P mini-size wireless motion detector
The JA-85P is a component of Jablotron’s Oasis 80 alarm system. The mini-
size motion detector uses a PIR sensor and it is designed for indoor use in
buildings or in cars. The battery-powered detector communicates via OASIS
radio protocol.
open here
+
lithium
battery
AA 3V
DIP switches
- see table
AA 3V
PCB
release
s
e
c
u
r
e
d
(
C
L
I
C
K
)
Installation
Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. The detector can be installed on a wall or
on a ceiling. In a car it can be installed high on the interior vertical surface
between the front and rear doors. Within the detection range of the PIR
sensor avoid the presence of objects rapidly changing in temperature, such as
electrical heaters, gas appliances etc. Moving objects with a temperature close
to that of humans such as curtains moving above a radiator, and pets should
also be avoided. Detectors should not be near fast-moving air e.g. near
ventilation fans or open windows or doors. There should also be no obstacles
blocking the detector’s “view” of the protected area. Keep the detector away
from metal objects which could interfere with radio communication.
Warning: The most frequent cause of false alarms is bad detector-
positioning.
Do not set (arm) this detector if there are any people or pets moving within
the protected area.
1. Release the detector installation bracket (by turning it clockwise).
2. Attach the bracket to a desired place and reinstall the detector onto the
bracket.
3. Open the detector cover by pressing the tab.
4. Remove the internal PIR module held by an internal tab.
5. Set the detector DIP switches (see the “DIP switches” section below).
6. Return the PIR module in to the plastic cover.
7. Leave the battery disconnected and the detector open and then follow
the receiver (or control panel or car alarm) manual. The detector enrolls by
connecting up its battery while the receiver is in enrollment mode.
8. After detector enrollment, close its cover, wait until its indicator turns off
and then test its functionality.
To enroll a detector after having already connected a battery, first disconnect
the battery, wait 30 seconds and reconnect it.
DIP switches
# OFF ON
1
Increased immunity with a
slower reaction (car use)
Normal immunity to false
alarms (indoor use)
2* Delayed natural reaction Instant natural reaction
3** Radio supervision off Radio supervision on
4*** 5 minute sleep time 1 minute sleep time
* This DIP switch has an effect if the detector is used with a CA car alarm or
with an Oasis control panel which has a natural reaction assigned to the
JA-85P’s address. It also has no effect when used with a UC-8x or AC-8x
receiver.
** Radio communication supervision should be switched off if a detector
installed in a car is enrolled to an Oasis control panel in a house (to avoid
lost detector indication when the car drives away).
*** To save battery energy, the detector switches to battery-save mode 15
minutes after the cover is closed. During battery-save mode the PIR sensor
still always watches out for movement. The first movement detected is then
transmitted instantly, and for the next 5 minutes or 1 minute the PIR sensor
ignores any further movement. After this period, the PIR sensor then returns
to watching out for movement until re-triggered.
Testing the detector
15 minutes after closing the detector cover, the LED shows detector
triggering. The strength and quality of detector signals can be measured by an
Oasis control panel in Service mode. If the detector is enrolled to a car alarm
and the ignition key is turned off then detector triggering is indicated by a short
flash of the LED.
Battery replacement
The detector battery is regularly checked. If the battery has expired, then the
user or installer is informed. The detector continues to work and each
movement in front of the detector is shown by a brief LED flash. The battery
should be replaced within two weeks by a qualified technician.
After battery replacement the detector needs two minutes to stabilise during
which the LED is permanently lit. After battery replacement test the
functioning of the detector. An expired battery should not be thrown into the
garbage, but disposed of according to local regulations.
Detection characteristics
The detector can react to movements within a distance of up to 5 meters,
see the following diagram.
r = 3m
r = 5m
4 m
2.60m
Car alarm co-operation
Several types of Jablotron’s car alarms allow for wireless detector
enrollment. A JA-85P detector, if enrolled, should be placed in the upper part
of car’s interior – e.g. fixed to the plastic part of the ceiling light, to side posts or
to the ceiling upholstery (this does not require the bottom handle to be used).
Always take the detection characteristic into consideration when positioning
the detector. Keep in mind that the spots behind mechanical obstacles (seats,
props) are invisible to the detector. Multiple detectors can be used
simultaneously – a detector has no effect to other detectors function.
The detector should not be exposed to direct sunlight . When arming a car
with a JA-85P enrolled all windows must be closed to prevent false alarm
caused by strong hot air blasts or by passing-by persons. However, this rule
can be omitted when partial arming is used and the detector belongs to the
INT group.
DIP switches No. 1 and 3 must be OFF .
Technical specifications
Voltage Lithium battery type CR14505 (AA 3.0V)
Calculated battery lifetime approx. 3 years (sleep time 5 min.)
Communication band: 868 MHz, Oasis protocol
Communication range: approx. 100m (open area)
PIR sensor detection angle/detection range: 360° / 5 m
Operational environment according to EN 50131-1 II. internal space
Operational temperature range -10 to +55 °C
Dimensions 88 x 46 x 27mm
EN 50131-1, CLC/TS 50131-2-2, EN 50131-5-3 classification: grade 2
Complies with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-
1,
ANSI C63.4
Can be operated according to ERC REC 70-03, FCC Part 15
FCC ID VL6JA85P
Jablotron Ltd. hereby declares that the JA-85P is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject the the following two conditions: 1. This
device may not cause harmful interference, and 2. this device
must accept any interference received, including interference
that may cause undesired operation.. The original of the
conformity assessment can be found on the web site
www.jablotron.com, Technical Support section. CAUTION:
Changes or modifications no expressly approved by Jablotron could void
the user´s authority to operate the equipment
Note : Dispose of batteries safely depending on battery type and
local regulations. Although this product does not contain any
harmful materials we suggest you return the product to the dealer
or directly to the manufacturer after use.
Internet: www.jablotron.com
Tel.: [phone]
fax: [phone]
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic