OPERATING MANUAL
JACK LALANNE POWER JUICER CONTENTS 3 Important Safeguards for the Power Juicer 4 Helpful Hints for the Power Juicer 5 Parts List for the Power Juicer 6 Assembly for the Power Juicer 8 Disassembly for the Power Juicer 9 Cleaning Your Power Juicer 10 Troubleshooting for the Power Juicer 2
JACK LALANNE POWER JUICER IMPORTANT SAFEGUARDS READ THESE SAFEGUARDS CAREFULLY BEFORE USING THIS PRODUCT! When using the Jack Lalanne Power Juicer, basic safety precautions should always be followed including the following: • NOT FOR USE BY CHILDREN! Keep out of the reach of children to avoid injury. The Power Juicer is not a toy. • Consult your physician before giving fresh juice to children, especially infants.
JACK LALANNE POWER JUICER HELPFUL HINTS Obtain the best results from your Jack LaLanne Power Juicer by following these helpful hints. • Do not put any fruit or vegetables in your machine until power is turned on. • Allow unit to run for at least 10 seconds before juicing. • Do not force food into the juicer. Allow food to pass through slowly and steadily using the pusher. You do not need to apply pressure unless the juicer starts to vibrate. Then only a slightly harder push should bring it back to balance.
Chute Pulp Guard Locking Bar Lip 5
JACK LALANNE POWER JUICER ASSEMBLY Assemble as shown STEP 1: Place base on a dry flat surface with locking bar in down position as shown. In front of the machine (spout side). 1 Base Locking Bar Front of Machine (Spout side) STEP 2: Place receptacle on the base, with juicer spout facing direction of locking bar. Settle receptacle into alignment. 2 Lip Juice Spout Receptacle Base STEP 3: Place filter inside receptacle, matching the opening on its bottom to the screw peg connected to the base.
JACK LALANNE POWER JUICER ASSEMBLY (CONT.) STEP 4: Place blade inside filter, centered over screw peg. Using orange crescent tool, place its pegs into the holes in the blade and turn clockwise Crescent until tightened. Tool IMPORTANT: Do not over tighten as the Blade screw peg will break. Holes Remove crescent tool and set aside. CAUTION: Do not leave tool inside juicer.
JACK LALANNE POWER JUICER DISASSEMBLY IMPORTANT: Before disassembling the unit make sure you turn the power OFF and unplug the machine from the electrical outlet. STEP 1: Remove pusher from the chute. 1 Pusher STEP 2: Lower the locking bar (silver) into position as shown. 2 Locking Bar Pulp Guard STEP 4: Use the crescent tool (orange) to remove the blade. Place the two pegs at either end of the crescent tool into the two holes on the blade, press down and turn counter-clockwise to unlock the blade.
JACK LALANNE POWER JUICER DISASSEMBLY (CONT.) STEP 5: Remove filter. STEP 6: Remove receptacle from base. 6 5 Filter Receptacle Base JACK LALANNE POWER JUICER CLEANING YOUR POWER JUICER • Turn off the power switch and wait until the motor completely stops. • With dry hands, unplug the power cord from electrical outlet. • Disassemble the Power Juicer. (See disassembly instructions.) • Clean all other parts in warm, soapy water. A mild detergent is recommended. Rinse well and dry thoroughly.
JACK LALANNE POWER JUICER TROUBLESHOOTING Problem The motor does not run after being switched on. Possible Reasons and Solution • Check to see if unit is plugged in. • Locking bar is not locked in place properly. • Check if all parts are assembled properly. • Check if there is any residue left between blade and receptacle. The motor is running with loud noise and shaking. • Check that all parts are assembled properly and in the correct position.
Exciting Offers from Power Juicer Accessory Kit & Cookbook Jack LaLanne’s Recipes for Healthy Living Cookbook Measuring Cup Overflow Platform Filter Brush Power Juicer Pulp Replacement Kit Power Juicer Blade Replacement Kit Pulp Guard Pulp Collector Pusher Filter Crescent Tool Blade www.powerjuicer.com Call 1-800-526-2518 9:00 AM – 7:00 PM EST Monday – Friday 9:00 AM – 5:00 PM EST Saturday Please allow 4-6 weeks for shipping.
We are very proud of the design and quality of our Power Juicer. This product has been manufactured to the highest standards. Should you have any problem our friendly customer service staff is here to help you if you have a question. We are available at: 1-800-526-2518 9:00 AM – 7:00 PM EST Monday – Friday 9:00 AM – 5:00 PM EST Saturday © 2006 Tristar Products, Inc. All rights reserved. Distributed By: Tristar Products, Inc.
