MANUFACTURERS WARRANTY ONE YEAR LIMITED PARTS & LABOR WARRANTY ALL NEW JACKSON DISHWASHERS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP, UNDER NORMAL USE AND OPERATION FOR A PERIOD OF (1) ONE YEAR FROM THE DATE OF PURCHASE, BUT IN NO EVENT TO EXCEED (18) EIGHTEEN MONTHS FROM THE DATE OF SHIPMENT FROM THE FACTORY.
CONTENTS BEFORE CONNECTING, OPERATING OR ADJUSTING THIS PRODUCT, PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY AND COMPLETELY. FOR YOUR CONVENIENCE, THIS MANUAL CONSISTS OF THE FOLLOWING SECTIONS IN THIS ORDER: 1. INSTALLATION 2. OPERATION 3. SPECIFICATIONS 4. CARE AND CLEANING 5. TROUBLESHOOTING 8. ILLUSTRATED PARTS LIST 7.
SAFETY PRECAUTIONS Never try to repair or replace any part of the dishwasher unless it is specifically recommended in this manual. All servicing should be done by a factory authorized service technician during warranty period, there are no user serviceable parts. Safety precautions in this manual are preceded by the words warning or caution and are very important. Warning means there is the possibility of personal injury to yourself or others. Caution means there is the possibility of damage to the unit.
GENERAL The Model 24LT Low-Temperature Chemical Sanitizing Dish machine requires 50 Parts Per Million of Chlorine be dispensed into the final rinse water for proper sanitizing of the ware. Installation of the Sanitizer, Detergent and Rinse Dispensing equipment connections must be made to back of machine before installing dish machine under counter or where installation will prevent access to back of machine. Dish machines not installed under counter must be leveled.
DRAIN CONNECTION The Dish machine is factory equipped with a Pump Drain system capable of pumping the drain water to a height of 24 inches from the floor. Approximately six (6) feet of drain hose is provided and attached to rear of machine. A hose barb and clamp are also provided along with a i~ 1/2" PVC Threaded Adapter for convenient installation to nearest dishwasher "y», CAUTION: Drain hose is factory mounted to rear of dish machine at MAXIMUM height of {24") at which drain water can be pumped.
INSTALLATION ELECTRICAL CONNECTION WARNING: All wiring connections must conform to the local and national electrical codes. Refer to machine electrical data plate located on front of machine and Specification section of this manual for proper electrical ratings. POWER CORD The dish machine is provided with six (6) feet of power cord so connection can be made to nearest receptacle. Do not alter or remove this power cord in any manner. STEPS: 1.
CHEMICAL DISPENSING EQUIPMENT The Model 24LT is equipped with a factory installed Sanitizer pump for accurately dispensing sanitizer into the final fresh water rinse. A Detergent and Rinse pump dispenser is not provided with this dish machine and must be installed prior to under counter installation. An electrical connection point and signal is provided for the installation of a Detergent and Rinse dispensing pump. Refer to the following instructions for proper installation of this equipment.
SANITIZER DISPENSING ADJUSTMENT The sanitizer dispenser pump is factory per-set to accurately dispense approximately 7.5 milliliters (S0 parts per million) sanitizing agent based solution of Sodium Hypercritical, Adjustment of the sanitizer dispenser pump timer nay be necessary depending on the type and sanitizer solution used. Consult your chemical representative for further details. Refer to Timer Adjustment section of this manual for proper adjustment of sanitizer dispensing.
GENERAL The timer is a self-contained (frame mounted) timer of the repeating cycle type. It is mounted behind the lower kick panel, where it controls the automatic functions of the machine. The timer motor operates on 115 volts, 60 cycles, taking (2) minutes to complete one full revelation. There are (7) micro switches which are controlled by rotating cams driven by the timer motor. Four (4) o©f the cams are adjustable and can be adjusted to either lengthen or shorten the desired function.
TIMER FUNCTIONS All timer functions are on marked on the timer frame adjacent to each timer cam controlling that function. The different cam functions are: TIMER "Not adjustable"” Fixed cam that controls the total length of the cycle, activated by the "START" switch. WASH "Not adjustable” Fixed cam that controls the wash cycle length. DRAIN "Not adjustable® Fixed cam that controls the draining of the tank during the drain/flush function.
SAN RINSE OET TIMER ADJUSTMENTS "ADJUSTABLE CAM" It operates the sanitizer pump that dispenses the sanitizer solution. By adjusting this cam you can either increase or decrease your amount of sanitizer solution. The cam is factory set to dispense 7.5 milliliters (50 parts per million) of sanitizing agent based solution of sodium hypocrite. Consult your chemical representative for further details on brand/type of chemical used and solution.
Lease check off the following items as they are completed, must be completed and checked off before proceeding In the event that your machine has missing parts or installation agency or call information is needed, please call, authoritative device telephone number provided on cover af this manual.
OPERATING INSTRUCTIONS GENERAL Please read the following operating instructions carefully and completely. Proper operation of your Model 24 LT will insure clean and sanitized ware. The Model 24 LT Low-Temperature Chemical Sanitizing Dish machine requires 30 Parts per Million of Chlorine be dispensed into the final rinse water for proper sanitizing of the ware. Use prime invite to prime line at start-up. MACHINE OPERATIONAL REQUIREMENTS WASH/RINSE water temperature must be a MINIMUM of 120 Degrees F.
OPERATING INSTRUCTIONS MACHINE OPERATION TO FILL (START-UP) STEPS : 1. Press Power Switch to "on® position, red lamp will light. 2. Remove Strainer Pan inside and p Press and hold the Fill Switch until water reaches level marked on tank. Replace strainer pan. Never operate machine without water. TO WASH 1. 1 Install upper and lower spray arms. 2. Check chemical bottles for adequate supply. NOTE: Low Sanitizer Lamp in Prime Switch will light when Sanitizer level in bottle is “LowW™. 3.
Thar E a Mo C Leaning DAILY (2-T times) OR AS DEEMED Clean the Strainer Pan daily or as needed to remove debris from strainer openings. NOTE: It is very important that the strainer pan is always clean. Clean the Drain Pump dally or as needed to remove debris from inside of pump housing. Drain machine completely and remove cap and clean, replace cap firmly. WEEKLY OR AS NEEDED Clean the Upper and Lower spray ares weekly or as needed. Remove snag disassemble spray arms as shown in Figure (&l.
TROUBLESHOOTING PROBLEM Machine does not operate (power switch light off) Power cord unplugged Circuit breaker tripped SOLUTION Check power cord Reset breaker Machine does not operate (power switch light on) Door open on machine Machine 5 AMP circuit breaker tripped Faulty Start Switch Faulty Timer Motor Faulty Timer Switch loose, disconnected or broken wire Close door Re seat Test switch Test motor Test switch Check wiring Will not Fill when depressing Fill switch (pewee light on) Faulty or obstructed inco
| J Company FACTORY SERVICE BULLETIN #144 JUNE 24, 1990 SUBJECT: MODEL 24L7T DOOR HINGE SIRING GENERAL.Z DOOR HINGE SPRING KIT WILL REPLACE SPRING AND ALSO SPRING KIT THESE PARTS Will NO LONGER BE AVAILABLE. THE NEW SPRING KIT MUST EE INSTALLED WHEN REPLACING all SPRINGS AND P/N0048106 SIRING KITS -~ NO PARTS ARE INTERCHANGEABLE. THE NEW DOOR SPRING HAS BEEN RE-ENGINEERED TQ IMPROVE DURABILITY AND RELIABILITY.
TORSION SPRING ASSEMBLY P 700011 PROCEDURE: * %* * Loosen £10 Screw and pull the screw half way thru the #9 Nylon Spacer. Place the #12 Spring Bushing into the #5 Spring with the spring's center bar in the bushing’'s slot. Insert the spring's hook around the nylon spacer; place the spring and spring bushing assembly into #4 Electric Box Channel; and tighten the #10 screw in place. Insert the #3 Bushing and #2 axle thru the #4 Electric Box Channel into the #12 Bushing's square hole.
BALL PLUNGER ASSEMBLY PROCEDURE Drill a 3/8" pia. hole in top of door at the proper location as shown on drawing. Insert Ball Plunger thru this hole. With your fingers, place the Push Nut on the ball plunger with the taper down. You should be able to engage the nut with your thumb and fingers. Hold the Ball Plunger with your fingers and use a screw driver to push the nut to a tight position. Note: Rotate Ball Plunger as the nut is being pushed on. Close the door.
ILLUSTRATED PARTS Liszt The Illustrated Parts List Section will contain exploded assembly drawings illustrating a complete replacement parts list for the Model 24 LT. When ordering a Replacement Part: PLEASE PROVIDE THE FOLLOWING INFORMATION: MODEL NUMBER SERIAL NUMBER REPLACEMENT PART NUMBER(S) CAUTION: Never substitute a replacement part with an unauthorized part.
L ILLUSTRATED PARTS LIST 1 ITEM NO.
ILLUSTRATED PARTS LIST ITEM NO.
ILLUSTRATED PARTS LIST VACUUM BREAKER PN 0184101 sonnet ITEM NO.
ILLUSTRATED PARTS LIST ITEM NO.
ITEM NO.
ILLUSTRATED PARTS LIST ITEM NO.
ILLUSTRATED PARTS LIST [_ITEM NO. | PART NUMBER DESCRIPTION OF PART 2 0034200 COUNTER, CYCLE 1 12600 CIRCUIT BREAKER, CHAMP 3 0172800 TIMER ASSEMBLY COMPLETE 0172801 2 TIMER MOTOR 115V 0172802 TIMER MICRO SWITCH 4 0122701 RELAY, MOTOR CONTRACTOR 5 0052118 PUMP, DRAIN 115V 0052111 PUMP, DRAIN VENT CAP 0052115 PUMP, DRAIN BLEEDER HOSE 0052116 PUMP, DRAIN, HOSE TO SOL.
SERVICE INSTRUCTIONS (INCOMING WATER SOLENOID YA LYE) SOLENOID VALVE PIN 0142100 {110V, used on 50 cycle machine} To take the naive apart Bonnet & Enclosing Tube Disassembly Disassembly — These valves may be taken apart by unscrewing the bonnet and the enclosing tube assembly from the naive body assembly. See Fig. 3. After unscrewing, carefully lift off the bonnet and enclosing tube assembly. Don't drop the plunger. The Plunger Assembly PIN 0148600 Q" ring seal and diaphragm cartridge can now be lifted out.
PART NUMBER DESCRIPTION 0142803 0151700 0153600 0160100 0160200 0160300 0160400 0160500 0166602 0166100 0172800 0172801 0172802 0184101 0184200 0199700 0199701 0194000 0199702 0199702 0159704 0199705 0187000 0052118 0052119 0052115 0052116 0052117 0141300 0160600 7000111 0212989 7000104 7000102 SOLENOID, VALVE, PLUNGER ASSEMBLY 1/2” STRAINER, PAN, WASH TANK STRAINER, “Y”, INCOMING HOT WATER 1/2” SWITCH, POWER, ON/OFF SWITCH, START AND PRIME, W/LAMP SWITCH, FILL/DRAIN SWITCH, DOOR CONTACT SWITCH, DOOR CONTAC
JACKSON MSC, INC World Headquarters & Manufacturing Operations Highway 26E, P.O. Box 1060 Bougainvillea, KY 40908 Fax: Nashville Office 801 Park Center Drive Nashville, TN 37127 Fax: LAl z Master Marketing South 146 Corporate Way Pet ham, AL 35124 Fax: Rick Hennessy, Tyler Proud Southern: Master Marketing South 5 Old West Point Road Belem, AL 36874 Fax: Stephanie Wall ALASKA: Performance Reps, N.W. 9923 SW. 178th Treat P.O.
A: Jones-Mcieod Appliance Service . 1616 7th Avenue North Birmingham, AL 35203 Jones-McLeod Appliance Service 854 Lakeside Drive Mobile, AL 36693 Al 1A: Authorized Commercial Food Equipment Service 1938 East Bosom Road Phoenix, AZ 85016 60272342443 (A2 only) AR : Bromide Gaits & Service 806 hazard St rest Little Rock, AR 72201 CAL Appliance Service 100 South Linden Avernus 8. San Francisco, CA 84080 P & D Appliance Service 4220-C: Rosalie Road N.
Eastern; Counties east of and including Toga, Commingling, Union, Juanita, Offline, Perry and Franklin.
JACKSON MAINTENANCE & REPAIR CENTERS ALABAMA CALIFORNIA DAWKINS COMMERCIAL 'GCS SERVICE ING #15 APPLIANCE SERVICE 3373 NW 18TH ST. JONES-McLeod BARKERS FOOD MACHINERY 300 8. HANDOUT STREET IMAM, FL 33056 APPLIANCE EQUIPMENT INGLEWOOD, CO 80110 (305) 1616 7TH AVE.
JACKSON MAINTENANCE & REPAIR CENTERS GARDEN CITY, I 83714 (208) 375-4073 AX: (208) 375-4402 ILLINOIS CONES REPAIR SVC. 2408 40TH AVE. MO LINE, 1l 61265 (300) 767-5323 800-716-707C FAX: SCHOPENHAUER SERVICES INC. 130 S OAKLAND ST. DECATUR, IL 62522 (217) 429-4229 800-252-5692 FAX: (217) 429-0226 GCS SERVICE INC. #12 696 LARCH AVE. HURST, iL 60126 (830) 941-7800 600-042-9689 FAX: (830) 941-6048 GCS SERVICE INC. #80 9722 REVISER PARK DR.
JACKSON MAINTENANCE & REPAIR CENTERS Selassie GCS SERVICE ING. 77 NEW MEXICO 'NORTH CAROLINA 3585 EAST PATRICK LANE (COMMERCIAL PARTS & SVC. SUITE 1000 STOVE PARTS SUPPLY GO, WHALE FOOD SERVICE 5755 GALLANT DRIVE LAS VEGAS, NV 83102 2120 SOLARIA STREET 8334-K ARROW RIDGE BLVD JACKSON, MS 39206 (601) 956-7800 800-274-5054 FAX: (601) 956-1200 COMMERCIAL PARTS & SVC.
ELECTRICAL APPLIANCE REPAIR SVC. 5805 VALLEY BELT ROAD CLEVELAND, OH 44131 (216) 459-8700 800-621-8259 FAX: (216) 456-8707 OKLAHOMA HAGAR RESTAURANT EMT. 1229 W MAIN STREET OKLAHOMA CITY, OK 73106 (405) 236-2184 B00-445-1791 FAX: {405) 236-6592 KRUGER INC. 100 NE 24TH STREET OKLAHOMA CITY, OK 73105 (405) 528-8883 800-522-8069 FAX: (405) 526-5405 OREGON RON'S SERVICE 16364 SW 72ND AVE PORTLAND, OR 97224 (503) 624-0890 800-851-4118 FAX: {503) 684-6107 PEN! 1A ALS.
JACKSON MAINTENANCE & REPAIR CENTERS VIRGINIA WISCONSIN INTERNATIONAL DAUBERS, INC, APPLIANCE SERVICE GLOBAL PARTS AND SUPPLY 7645 DYNAMITE COURT CENTER, INC. 7758 NW 72ND ST SPRINGFIELD, VA 22153 2439 ATWOOD AVE MIAMI, FL 33166 (703) 866-3600 800-564-7768 FAX: {703) 866-4071 GCS SERVICE INC, #07 2650 PITTMAN DRIVE SILVER SPRING, MD 20810 (301) (410) 800-636-7278 FAX: GCS SERVICE INC. #18 2421 GRENOBLE RD. RICHMOND, VA 23294 (804) 672-1700 800-899-5349 FAX: (804) 872-2888 GCS SERVICE INC.
