Manual

ManualsBrandsJaclo ManualsWater equipment½" thermostatic valve - J-THVC12

j a c l o i n d u s t r i e s | 129 Dermody Street Cranford, NJ 07016

p 908.653.4433 | 800.852.3906 f 908.653.1717 | 800.852.4133

JACLO.COM

PG 1 REVISED JULY ‘08THERMOSTATIC WALL VALVE

INSTALLATION INSTRUCTIONS

Two-Handle Thermostatic Wall Valve

With Integral Volume Control

Product Number: J-THVC12

Please read instructions carefully before beginning the installation.

INSTALLER WARNING

› Follow all applicable Local Plumbing Codes, Public Health and Safety Codes.

2 › This unit has no serviceable ﬁlter. See Valve Maintenance Section.

3 › Before installation, ﬂush all pipes thoroughly.

Summary of content (10 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Two-Handle Thermostatic Wall Valve With Integral Volume Control Product Number: J-THVC12 Please read instructions carefully before beginning the installation. INSTALLER WARNING 1 › Follow all applicable Local Plumbing Codes, Public Health and Safety Codes. 2 › This unit has no serviceable filter. See Valve Maintenance Section. 3 › Before installation, flush all pipes thoroughly. . JACLO.
PAGE 2
Thermostatic Valve Flush Tube Set 30 29 0-1050-29 JACLO.
PAGE 3
ITEM 1 2 3 4 5 6 7 8 9 10 11H 11C 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 QUANTITY 1 1 1 1 2 1 1 1 1 1 1 1 2 2 2 2 2 2 1 1 1 1 1 2 1 1 1 1 ~ 1 1 DESCRIPTION Dual Therm. Valve Body 1/2" Therm Valve Replacement Cartridge Therm. Valve Cartridge Lock Nut Therm. Valve Limit Stop Ring Stainless Steel Limit Stop Spline Adapter Temperature Dial Dial Pointer Dial Sleeve Gasket Set for Dual Therm. Hot Check Stop Body Cold Check Stop Body Therm.
PAGE 4
ROUGH INSTALLATION 1 › Make sure hot and cold water is piped to the correct valves inlets. 2 › Do Not Solder Connections unless valve is kept cool and heat is no closer than 3" to body. Otherwise remove check stops and cartridge. (See check stop removal section). 3 › Postion valve so the finished wall falls between min./max. thickness mark on the rough-in shield. Caution: Valve can accommodate walls up to 1" thick. For walls up to 2" thick order a DUAL THERM_ EXT Kit (See Page 2).
PAGE 5
LIMIT STOP & TEMPERATURE SETTING 1 › Make sure stop ring notch and cartridge notch are aligned with line on spindle spline (see Fig. 2A). Close volume control. Make sure hot & cold check valve/stops are open by rotating until the open arrows point to the center of the valve. (See Fig. 2). Screw sleeve (9) onto valve body until it bottoms tight on plastic stop ring. 2 › Open volume control 3 › Valve is set to 100°F max. Pressure and temperatures vary. Check 100°F setting with thermometer.
PAGE 6
DIAL POINTER, TRIM & HANDLE INSTALLATION 1 › Rotate the spindle until the temperature of water stabilizes at 100°F. 2 › Push the dial pointer (8) into sleeve (9), with the arrow up in the 12 o’clock position (Fig.6). Install dial assembly (6) over the spindle until it bottoms (without rotating it), aligning the 100°F marking to the arrow of the insert (8). 3 › Place the self adhesive backed foam strip (24) onto the inside surface of the traditional front plate (18) only.
PAGE 7
TROUBLE SHOOTING GUIDE PROBLEM Water leaks from shower head / tub spout when the volume control is shut off. Water is hot or cold but not mixing. Can not adjust water temperature properly. POSSIBLE CAUSE SOLUTION The shower head is trapping water behind the faceplate. Remove shower head and clean out the holes in the faceplate. Reinstall shower head. The volume control valve has been installed incorrectly. Arrow on side of volume control should be pointing away from the thermostatic valve.
PAGE 8
Valve maintenance › CAUTION: DO NOT ATTEMPT TO SERVICE THE THERMOSTATIC VALVE UNLESS VOLUME CONTROL VALVES ARE SHUT OFF. OTHERWISE SERIOUS CHECK VALVE / STOP DAMAGE WILL OCCUR. THERMO CARTRIDGE REMOVAL & INSTALLATION Refer to Fig. 1, Page 2 1 › First - Shut off the volume control valve (s). (See pg. 4) 2 › Second - Shut off the check valve / stops by rotating each one half a turn (180°), until the OFF arrows point in the direction of the water flow (toward the center of the valve). (See Fig.
PAGE 9
procedure to flush thermostatic valve 1 › Shut off water supply to valve. 2 › Remove stop nut and check valve/stop (hot & cold). Rotate to make removal easier. 3 › Screw in flushing adapters (hot & cold). 4 › Turn on water. Flush for 30 seconds to remove any debris from lines. 5 › Remove flush adapters (hot & cold). 6 › Reinstall check/valve stop (hot & cold) and stop nut. Rotate to make installation easier. JACLO.
PAGE 10
JACLO PRODUCT CARE Thank you for selecting a JACLO product. In order to maintain the high quality finish of the product you have purchased, please adhere to the following product care instructions: Cleaning metal parts: For routine cleaning simply use a soft damp cloth and common household soap, then rinse and dry. Proper care of your product is important because most water contains calcium that deposits on surfaces, forming unpleasant spots.