Use and Care Guide
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for
whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath
by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the
bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for
shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of
warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath must
be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool
Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.
1
BATHS WITHOUT INTEGRAL SKIRT
END VIEW
H
W
SIDE VIEW
L
2"
51 mm
BATHS WITH 3-SIDED TILE FLANGE
L
1"
25.4 mm
H
W
SIDE VIEW
END VIEW
L
1"
25.4 mm
H
W
SIDE VIEW
BATHS WITH 4-SIDED TILE FLANGE
END VIEW
L
1"
25.4 mm
H
W
SIDE VIEW
BATHS WITH INTEGRAL SKIRT
END VIEW
DRAIN/OVERFLOW
A
B
SPECIFICATIONS (Rectangular)
MODEL
PRODUCT
WEIGHT
OPERATING
GALLONAGE
TOTAL WEIGHT/
FLOOR LOADING
DIMENSIONS
DRAIN/OVERFLOW
DIMENSIONS
SKIRT &
MOUNTING
CUTOUT
AVAILABILITY OF
"RAPIDHEAT"
IN LINE HEATER
AMIGA™
72" (1829 mm) L*
36" ( 914 mm) W
20-3/4" ( 533 mm) H
772 lb
(351 kg)/
43 lb/sq. ft.
(210 kg/sq. m)
50 U.S. gal
(186 liters)
105 lb
(48 kg)
16-7/8" (429 mm) A
14" (356 mm) B
Optional,
U-Frame
70" x 34"
Yes
FOR ALL UNITS:
MOTOR/PUMP: 115 VAC, 3450 RPM/10 AMP, 60 Hz Single phase.
ELECTRICAL SERVICE REQUIREMENTS: 115 VAC, 15 AMP, 60 Hz. RapidHeat: 115 VAC., 15 Amp, 60 Hz.
All require a dedicated GFCI protected separate circuit.
*Add 1/4" to this dimension when roughing-in for 3-wall niche.
BIANCA™
72" (1829 mm) L*
48" (1219 mm) W
20-1/2" ( 521 mm) H
993 lb
(451 kg)/
41 lb/sq. ft.
(200 kg/sq. m)
73 U.S. gal
(276 liters)
135 lb
(61kg)
16" (406 mm) A
8-1/2" (216 mm) B
Optional,
U-Frame
70" x 46"
Yes
AMIGA™
WITH INTEGRAL
SKIRT
72" (1829 mm) L*
36" ( 914 mm) W
20-3/4" ( 533 mm) H
796 lb
(362 kg)/
44 lb/sq. ft.
(214 kg/sq. m)
50 U.S. gal
(186 liters)
129 lb
(59 kg)
16-7/8" (429 mm) A
14" (356 mm) B
Integral
NA
Yes
CETRA™
WITH INTEGRAL
SKIRT
60" (1524 mm) L*
32" ( 813 mm) W
20-1/2" ( 521 mm) H
727 lb
(330 kg)/
55 lb/sq. ft.
(268 kg/sq. m)
46 U.S. gal
(174 liters)
94 lb
(43 kg)
17-7/8" (454 mm) A
9-3/8" (238 mm) B
Integral
NA
Yes
CETRA™ 536
60" (1524 mm) L*
36" ( 914 mm) W
21-1/4" ( 553 mm) H
742 lb
(337 kg)/
50 lb/sq. ft.
244 kg/sq. m
48 U.S. gal
(181 liters)
92 lb
(42 kg)
Optioal
U Frame
58"
X
34-1/4"
18-1/2" ( 470 mm) A
9" ( 229 mm) B
Yes
CETRA™ 532
60" (1524 mm) L*
31-7/8" ( 791 mm) W
21-1/4" ( 553 mm) H
697 lb
(317 kg)/
53 lb/sq. ft.
(259 kg/sq. m)
43 U.S. gal
(181 liters)
89 lb
(41 kg)
Optioal
U Frame
58"
X
30-1/4"
18-1/2" ( 470 mm) A
9" ( 229 mm) B
Yes
RECTANGULAR BATHS