OWNER’S MANUAL Assembly, Installation & Operating Instructions TM J-DREAM II Shower System
IMPORTANT SAFETY INFORMATION READ ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise the internal human body temperature excessively and impair the body's ability to regulate its internal temperature (resulting in hyperthermia). Consult your physician about your safety and comfort before using the steam system; limit your use of steam to 10-15 minutes until you are certain of your body's reaction.
Contents Part I Assembly & Installation Specifications _______________________________________________________________________ General Information __________________________________________________________________ Packaging __________________________________________________________________________ Hardware Identification ________________________________________________________________ Rough-in ___________________________________________________________________________ Base and Drain ________________________
J-Dream II Owner's Manual R WHIRLPOOL BATH FRONT VIEW 3" (76 mm) CLEARANCE TO REMOVE DOME 83" (2108mm) 81" (2057mm) 60" (1524 mm) TOP VIEW 60" (1524mm) 11 5/8" SERIAL NUMBER LOCATION (295mm) (AT TOP) ON BACK OF EQUIPMENT SEAT WALL 21 1/2" (546mm) 42" (1067mm) SPECIFICATIONS DIMENSIONS TOTAL WEIGHT/ FLOOR LOADING REQUIRED WATER SUPPLY PRODUCT WEIGHT ELECTRICAL REQUIREMENTS* SHIPPING WEIGHT 60" (1524mm)L 42" (1067mm)W 83" (2108mm)H 833 lb (379 kg) 47.
J-Dream II Owner's Manual Read all instructions before beginning assembly and installation. General Assembly Information The J-Dream II shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door. This manual details the assembly, installation and operation. After the drain, water supply stub-out, and electrical supply are provided, the shower unit should be assembled freestanding away from the walls of the room.
J-Dream II Owner's Manual Electrical requirements Your J-Dream II, as it comes from the factory, requires a GFCI protected 240 VAC 3- wire 20 AMP 50-60 Hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in that circuit. If you do not have this kind of circuit, a qualified electrician should be called in to install the necessary wiring.
J-Dream II Owner's Manual J-Dream II Packaging 6 cartons packed together on a wooden crate.
J-Dream II Owner's Manual Letters (A) are used in the illustrations of the assembly procedure. A CLIP U-CLIP 10-24 B PAN HEAD SCREW #10-24 x 3/4" SCREW C WASHER FLAT WASHER 1/4" D NUT LOCK NUT 10-24 E SCREW FLAT HEAD SCREW M4x10mm J NUT 1/4-20 LOCK NUT K WASHER FLAT WASHER #10 L SCREW SIDE BRACKET PAN HEAD SCREW #12 x 1/2 L BRACKET G BOLT HEX BOLT 1/4-20 x 1.5" LAG SCREW H BOLT SELF-TAPPING M6x50mm CLAMP F SCREW I WASHER EXTERNAL TOOTH LOCK-WASHER 1/4 6 PAN HEAD SCREW #6-32 x .
J-Dream II Owner's Manual Rough-in WASHING MACHINE OUTLET BOX 37" HOSE BIBB (2) (2) 1/2 " HOT & COLD WATER SUPPLY LINES CONNECT #8 GAUGE (10mm2) MINIMUM SOLID COPPER BOND WIRE TO THE HOUSE ELECTRICAL PANEL OR APPROVED LOCAL GROUND. AN APPROVED GROUND MAY BE AN 8 FOOT LONG GROUND ROD (3 METER LONG EARTH ROD), A PLATE ELECTRODE, OR OTHER ACCEPTABLE BOND. CHECK YOUR LOCAL BUILDING CODE FOR REQUIREMENTS. (SEE PAGE 22 FOR BONDING INSTRUCTIONS).
J-Dream II Owner's Manual Locate Base to provide assembly access to all sides Remove Base from carton labeled Base/Top. Place Clear Top in carton to prevent damage. (The Clear Top will not be installed until the unit has been fully assembled and plumbed). Position the J-Dream base on the floor so that you have work access to all four sides of the unit during assembly. (Allow a minimum of 24" (600 mm) of access on each side of base.
J-Dream II Owner's Manual Drain Fitting (provided with unit) Leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flush with the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the shower unit. Studwall Temporary Wood Block Drain Compression Fitting Drain Assembly Floor Remove the block and pull the drain assembly up to insert the stub into the drain.
J-Dream II Owner's Manual Attach Seat Walls to Base (J-Dream II with stereo shown) Bolts (8) G Align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath.
J-Dream II Owner's Manual Attach Panel #2 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. Screw (4) Washer (4) C F You may want to swing the hinged seat wall open to get better access to the installation of the screws. Panel #2 Remove these 4 screws to swing the seat wall open.
J-Dream II Owner's Manual Attach Panel #3 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. You may want to swing the hinged seat wall open to get better access to the installation of the screws.
J-Dream II Owner's Manual Install Back Wall Caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat walls. Pan lip Parallel Back wall B Washer (8) C Nut (4) D Caulk A Panel #2 Screw (4) B Panel #3 A Nut (4) Washer (8) D Seat walls not shown in this illustration for clarity.
J-Dream II Owner's Manual Attach Panels #1 and #4 to Seat Walls Remove 4 bolts from seat walls to attach panels # 1 and #4. Caulk along surface of seat walls. Caulk Seat wall attaches to panel #1 and #4 in two places. Caulk Seat wall attaches to panel #1 and #4 in three places. Nut (3) D B Washer (10) Reinstall bolts (4) and washers (4) removed from seat wall and bracket C Screw (3) B A.
J-Dream II Owner's Manual Attach Brackets to Seat Wall Frames and L Bracket to left Angle Bracket Bolt (remove top bolt from seat wall bracket and reinstall). See below dimensions for bolt locations. Seat Wall Side Bracket Nut (2) D Panel #4 Frame Screw (2) B A B C Bolt (remove top bolt from seat wall bracket and reinstall). See below dimensions for bolt locations.
J-Dream II Owner's Manual Attach Painted Angle Brackets to Panels #1 and #4 Note that each angle bracket has a notch on the top and bottom. This notch does not get screwed against the side panels but faces out as shown in the side view for both left and right sides. Do not tighten the screws at this time as the angle brackets will have to be aligned with the door frame holes.
J-Dream II Owner's Manual Attach Door Frame to Angle Brackets and Base Frame Before proceeding, make sure the seat walls are closed and fastened. See detail B on page 15. Align door frame over tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame. Align holes along sides of door frame with angle brackets and mark this position of the angle brackets. Remove door frame and angle bracket screws. Apply the silicone caulk and reinstall the angle brackets at the marked position.
J-Dream II Owner's Manual Attach Top Frame to Door Frame, Back Wall and Seat Wall Frames Press/tap top frame into door frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure. Frame snaps down into door frame and back snaps over back wall. Install bolts (4) through top frame and into left and right seat wall frames.
J-Dream II Owner's Manual Left Seat Wall Feed the four hoses and controller cable from the back wall and connect them as shown. The steam hose connection uses a hose clamp while the other hoses use spring clamps that are on the hoses. Also feed the CD/Radio wire bundle to the back wall. (J-Dream II with stereo only.
J-Dream II Owner's Manual Back Wall Use cable ties to attach the CD/Radio wire bundle to the cascade hose. The hoses from valves 1 and 3 and the steam hose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seat wall is swung open (like a door) to access equipment. After they have been connected and there is sufficient slack, the cable ties may be tightened.
J-Dream II Owner's Manual Right Seat Wall (Equipment Wall) Connect the hoses routed from the back wall as below (grayed lines are pre-attached). Connect the controller line. The red and black leads in the CD/Radio wire bundle must be hooked up to the corresponding colored leads of the power supply. Connect the speaker leads. Connect the two SteamPro power cords after unraveling them.
J-Dream II Owner's Manual Bonding (top left hand side of right hand equipment seat wall) Connect a #8 guage (10mm2) minimum solid copper bond wire to the house electrical pannel or an approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode or ther acceptable bond location. Check your local building code for requirements.
J-Dream II Owner's Manual 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Make sure electric power is OFF at main breaker. Static test water supply hoses for leaks. Plug power cord into GFCI protected wall outlet. Move the assembled J-Dream II into final position. Connect 2" shower drain (see page 9). Adjust the levelling screws in the J-Dream II base feet and lock them in position. Recheck fit of drain plumbing. Secure J-Dream II in position using clamps provided as shown in Figure 1.
J-Dream II Owner's Manual Attach Front Panels to Unit Attach both left and right front panels with pre-installed Velcro®. On the left front panel, install 2 screws through the top of the panel. Connect the CD/radio ground wire, speaker/power connector and antenna wire before installing left front panel. Ground wire is bolted to the seat wall frame.
J-Dream II Owner's Manual Top Cover Place cover on top of unit. Align notch in cover with the corresponding notch in the top metal frame.
J-Dream II Owner's Manual Turn On Electric Power at Main Breaker Operate Unit and Check for Leaks Attach Bottom Front Panel to Unit Take the bottom panel at an angle and insert under the bottom of the enclosure frame. Rotate backwards till it is up against the brackets with the pre-installed Velcro®. Enclosure Base Frame Panel Use finishing strip material (not provided) to cover gap between J-Dream II and finshed wall. Do not attach finishing strips to face panels.
Part II: Operating Instructions CONTROL PANEL System control is provided by the electronic display located inside the shower cabin (see Figure 1) The display is used to start up the five functions of the unit: the shower, the cascade waterfall, the hydromassage (all jets), hydromassage (pulsed jets), and the steam bath. The display is composed of clear symbols to identify the five functions.
Starting the Hydromassage The J-Dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 16 water jets (four sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, press the JETS button once (Figure 1). This will activate the jets on one wall. Pressing it a second time will shut OFF that wall and activate the other wall.
Care and Maintenance of SteamPros Maintenance of the Steampros includes flushing and visually inspecting for water leaks. To flush the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPros, the seat wall (equipment wall) must be swung open. To do so, remove the three screws from door frame (refer to page 17, diagram A). Then remove right front panel. Refer to page 11 and remove the four bolts indicated.
Troubleshooting Chart PROBLEM PROBABLE CAUSE 1. Control is on and appears to be functioning, but no steam. A. Steamer heating up. B. High limit safety switch tripped. REMEDY A. Allow 2 minutes for steam to flow. B. Replace water filter, drain and flush out steamer and steam plumbing. Pour six ounces of water into the steam delivery tube. Reset high limit safety switch. 2. Steam generator will fill and produce steam, but will boil water away without refilling and shut itself off. A.
31
32
Jacuzzi Whirlpool Bath Limited Warranty Shower System Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed.
