Installation Sheet

Page10 www.jacuzzi.com InstallationandOperation
English
 SignatureSeries
 SignatureSeries
ON/OFFButton
ON/OFF Button
Fig. 12
Whirlpool Control
Intheclosedposition,thejetsmassagewith
onlywater.
Intheopenposition,airmixeswithwater
tocreateadeep,wideplumeofmassaging
bubbles.
Fig. 13
OPENPosition CLOSEDPosition

PushdownonthebuttontoturnONthewhirlpoolsystem.

PushdownonthebuttontoturnOFFthewhirlpoolsystem.
Direction (Figure14A)
Tochangethedirectionofthewaterow,swivelthejetnozzleto
thedesiredangle.
Water Force (Figure14B)
Increasetheforceoftheowbyrotatingthejetfacetotheleft
(counterclockwise).
Decreasetheforceoftheowbyrotatingthejetfacetotheright
(clockwise).
Neverrunthewhirlpoolsystemwithallthejetsclosed.
Water ForceDirection
TheheaterturnsONautomaticallyanytimewhirlpool
operationisactive.Heateroperationisnotdisplayedonthe
controlpanel.Thereisavisibleindicatorlightontheheater
itselfthatsigniestheheaterisoperating.Theheaterwill
helpmaintainthetemperatureofthewaterinthebathtub
(Figure15).
Theheaterisequippedwithapresetvacuumswitchwhichwill
notallowtheheatertoturnONifthepumpisnotrunningand
waterisnotowingthroughthewhirlpoolsystem.
TheheaterincludesanexclusiveHigh-Limitswitch.Thissafetycircuitwillnotfalsetripfromhottapwater.Itwill
onlyturnOFFtheheaterifthethermostatfails.Toreset,pressthebutton.Ifthehigh-limittripsfrequently,please
contactusatwww.jacuzzi.com,orat1-800-288-4002.
Vacuum Switch
High-Limit Switch
PUSH TO RESET
OVER HEAT
PROTECTION
HEATER ON
HighLimitReset
HeaterOn
Fig. 15
Fig. 14A Fig. 14B
Cleaning
Ifyouwanttouseanykindofbathtubadditive,useonlyasmallamountoflow-foamingpowderorcrystalsubstance;
thewhirlpoolactionintensiesthefoamingpropertiesofsoaps.
Theuseofcertainbathtuboils,bubblebaths,andbathtubadditivesmayincreasethelevelofaccumulationsofbathtub
residueinthewhirlpoolsystemandmaycausefalsereadingofthewaterlevelsensors.Ifexcessaccumulations
persist,youshoulddiscontinueuseoftheseproducts.
Toremoveaccumulationsofbathtubresiduefromthewhirlpoolsystem,itisrecommendedthatabathtubbecleaned
regularly.Forbestresults,however,werecommendthatyoucleanyourbathtubaftereachuseusingSystemsClean™,
ourexclusivetwo-partplumbingsystemcleanermadespecicallyforwhirlpoolbathtubs.SystemsClean™isavailable
throughanauthorizedJacuzziLuxuryBathDistributororbycallingusdirectat1-800-288-4002ormaybepurchased
onlineatwww.jacuzzi.com.
CAUTION
CAUTION
 Do not use oil or oil-based bathtub additives. Never use abrasive, or caustic, household
cleaners on any Jacuzzi Luxury Bath product.
RapidHeat™