Installation/Operation Instructions for Shower Towers EC30000 Ristorre™ Onda™ EC31000 Ristorre™ Ovale™ EC33000 Ristorre™ Metallo™ Ovale™ Onda™ Metallo™ Save These Instructions for Future Use. Complete and mail-in the product registration card provided with your unit. Write and save the model and serial number of your unit. Installer: Leave this manual for homeowner. Homeowner: Read this manual and keep for future reference.
SAFETY INSTRUCTIONS NOTE: MINIMUM WATER PRESSURE FOR THESE SYSTEMS IS 40 PSI. Warning: When using this unit, basic precautions should always be followed, including the following: DANGER: Do not place or use electrically connected devices, such as television, radio, or stereo speakers, lights, hair dryers, or telephones, within 1.5 m (5 feet) of shower. IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.
Ristorre™ Ovale™ Shower Tower — Specifications Optional-Supplied Temperature Check Spout DIMENSIONS SHIPPING WEIGHT 3" ( 76 mm) D (Depth) 10-1/4" ( 260 mm) W 46-5/8" (1184 mm) H 27 lb (13.3 kg) Product specifications are subject to change without notice. PRODUCT WEIGHT 22 lb (10 kg) Minimum Working Water Pressure 21.76 psi (1.5 bar) Maximum Working Water Pressure 72.52 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) Maximum Working Water Temp.
Ristorre™ Onda™ Shower Tower — Specifications Optional-Supplied Temperature Check Spout DIMENSIONS SHIPPING WEIGHT 3" ( 76 mm) D (Depth) 13-1/2" ( 343 mm) W 51-1/4" (1302 mm) L 29 lb (13.2 kg) Product specifications are subject to change without notice. PRODUCT WEIGHT 25 lb (11 kg) Minimum Working Water Pressure 21.76 psi (1.5 bar) Maximum Working Water Pressure 72.52 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) Maximum Working Water Temp.
Ristorre™ Metallo™ Shower Tower — Specifications Optional-Supplied Temperature Check Spout DIMENSIONS SHIPPING WEIGHT 2-1/2" ( 63.5 mm) D (Depth) 12-3/4" ( 1905 mm) W 55-7/8" (1419 mm) L 29 lb (13.2 kg) Product specifications are subject to change without notice. PRODUCT WEIGHT 26 lb (12 kg) Minimum Working Water Pressure 21.76 psi (1.5 bar) Maximum Working Water Pressure 72.52 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) Maximum Working Water Temp.
Ristorre™ Ovale™ Shower Tower — Component Identification 8 7 18 9 4 10 11 1 5 15 18 17 19 17 14 7 6 5 4 3 0a 0b 0c 13 1 1 6 16 13 8 no. name Qty Remark no. 1 Tempered glass Front Plate 1 Body Jet 6 3 Wall mount Shower 1 Included 4 Shower arm 1 Included 5 Back Housing 1 6 gasket 1 7 Wall mount Fixing Rod 8 Screw(m4. X35mm) 9 name Qty Remark 16 S.S.
Ristorre™ Onda™ Shower Tower — Component Identification 7 18 1 4 8 9 10 11 3 19 17 18 14 15 5 17 0a 0b 7 6 0c 1 l na ptio o 3 4 5 13 1 16 13 FRONT no. name 6 8 Qty SIDE Remark no. BACK name Qty Remark 1 Tempered glass Front Plate 1 16 S.S.Flexible Hose 1 Included Body Jet 6 17 Hand Shower Bracket 1 Included 3 Wall mount Shower 1 Included 18 Plastic anchor 5 Included 4 Shower arm 1 Included 19 Screw(m3.
Ristorre™ Metallo™ Shower Tower — Component Identification 10 1 21 11 3 6 8 15 20a 14 27 26 25 17 20b 9 20c 19 18 19 18 12 13 7 7 Red means connect to hot water 2 23 Blue means connect to cool water 24 Wall 22 21 16 13 28 no.
Common Parts List name Qty Remark name Qty Remark 1 Square Temp Check Spout 1 0c Thermo-Static Control 1 13 Tube Temp Check Spout 1 1 Sealing Washer 5 14 glass Shelf assembly 1 Threaded Connector 1 15 Hand Shower 1 3 Brass nut 16 Shower Flexible Hose 1 4 Spring Washer 17 Hand Shower Bracket 1 5 Washer Plate 18 Plastic anchors 6 6 Silica gel Washer 19 (m3.
INSTALLATION IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements. Each unit arrives ready for installation, completely equipped with plumbing and fittings. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. CAUTION: Do not drop the shower tower. Dropping the unit may damage its appearance and function. Immediately upon receipt, inspect the unit before installing.
Assemble and Install the Shower Tower 1. Attach the shower arm and prepare the glass shampoo platform as follows. a. Attach the shower arm (4) to the front plate (1) with screw nut (11), see Figure 4. Confirm the screen washer at the water inlet fitting of the wall mount shower head (3) is in place and screw the shower head onto the shower arm by hand. Finally, place a sealing washer (21) into the end connector of the flexible tubing as shown in the Figure, and fasten the tubing connector to the shower arm.
2. Connect 1/2" hoses from the front plate (1) marked in red and blue to the hot and cold water supply’s, respectively, as shown in Figure 7. NOTE: Do not bend or kink the hoses when installing. Tighten fittings with a wrench and test for leaks. Figure 7 NOTE: Figure 8 shows the hot and cold supply locations. 7 10 9 9 BLUE HOSE RED HOSE 3. Align the three mounting holes of the back housing (5) and front plate (1) with the three mounting rods (7) on wall.
4. Using the dimensions indicated in Figure 9, drill two holes 1/4” diameter by 1-3/8” deep into the wall on the right hand side of the shower tower. Insert the plastic anchors (18) into each of the holes, and mount the bracket (17) onto the wall using the M3.5x25mm Screws (19). Figure 9 9-7/8" (250 mm) 19 19 16 17 18 18 2" (23 mm) 2 HOLES 1/4" DIA. (6,4 mm) x 1-3/8 " (35 mm) DEEP 63" (1600 mm) 2 HOLES 1/4" DIA. (6,4 mm) x 1-3/8 " (35 mm) DEEP TO FLOOR 5.
OPERATION 1. CONTROL VALVE. The Control Valve consists of three parts, the diverter (20a), flow control (20b), and thermo-static control (20c). a. Diverter 20a The Diverter (20a) works as a function selection. Four icons on the diverter indicate the function selected. The four icons represent the following four functions: Hand shower spray Bath spout , Body jets , Wall mount spray , and . 20b b.
Jacuzzi Whirlpool Bath Limited Warranty Shower System Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed.