User's Guide
Table Of Contents
- THINGMAGIC M6e User Guide
- Introduction
- Hardware Overview
- Hardware Interfaces
- Digital/Power Connector
- USB Interface
- General Purpose Input/Output (GPIO)
- Power Requirements
- Special RF Power Output Requirements for the M6e-A
- Environmental Specifications
- Electro-Static Discharge (ESD) Specification
- Mounting Screw Clearance
- Assembly Information
- Antennas
- M6e Mechanical Drawing
- Authorized Antennas
- M6e-A Authorized Cables
- Firmware Overview
- New Features - Version 1.21.2
- Margin Read Support for Monza6 Tags
- NXP UCODE7 Configuration Support
- Gen2 Parameters in Metadata
- Support for Acura Gen2V2 Tags
- Support for GEN2V2 Embedded Tag Ops
- Gen2V2 Support
- Denatran Tag Support
- Configurable T4 for Gen2 Protocol
- Ability to “Read Data” Immediately After Sending a “Write EPC” or “Write Data” Command
- Decoupling Antenna Selection from AsyncOnTime
- Support for Additional Regions
- Support for Set/get Quantization Value and Minimum Frequency in Open Region
- Operational Notes
- Boot Loader
- Application Firmware
- Custom On-Reader Applications
- New Features - Version 1.21.2
- Communication Protocol
- Functionality
- Specifications
- Compliance and IP Notices
- Error Messages
- Getting Started – Development Kit and Carrier Board
- Environmental Considerations
ThingMagic M6e User Guide 46
www.JADAKtech.com
This radio transmitter (identify the device by certification number, or model number if Category II) has been
approved by Industry Canada to operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the
device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the Equivalent Isotropically Radiated Power (EIRP) is not more than that permitted for successful
communication.
This device has been designed to operate with the antennas listed in the
Authorized Antennas table.
Antennas not included in these lists are strictly prohibited for use with this device.
To comply with IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for
this transmitter must be installed to provide a separation distance of at least 35cm from all persons and
must not be colocated or operating in conjunction with any other antenna or transmitter.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains ThingMagic M6e (or appropriate model number you are filing with IC) transmitting module FCC
ID: QV5MERCURY6E-A (IC: 5407A-MERCURY6EA)”
Industrie Canada (French Canadian)
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle
s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les
types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur
Le fonctionnement de lʼ appareil est soumis aux deux conditions suivantes:
1. Cet appareil ne doit pas perturber les communications radio, et
2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son
dysfonctionnement.
Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être
choisis de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas celle nécessaire
pour une communication réussie.
Lʼ appareil a été conçu pour fonctionner avec les antennes énumérés dans les tables Antennes Autorisées.
Il est strictement interdit de lʼ utiliser lʼ appareil avec des antennes qui ne sont pas inclus dans ces listes.