ACACIA TS-051 Installation Guide
ACACIA TS-051 Toilet Manual Invisible L-Mount Brackets Table of Contents 1. Sizing and Details 1 2. Necessary Tools and Materials 2 3. Precautions Before Installation 3 4. Installation 4-7 a. Positioning of the Drain Socket Flange 4 b. Installation of the L-Mount Brackets 5 c. Installation of the Toilet 6 d. Installation of the Toilet Seat 7 5. Recommended Measurements 8 6. Testing Operation 8 7. Troubleshooting & Solutions 8 8. Product Warranty 10 9.
SIZING AND DETAILS ACACIA TS-051 Contemporary european toilet with dual flush LENGTH 26” WIDTH 15.16” HEIGHT 26.57” WATER CONSUMPTION 1.6 GPF / 0.
NECESSARY TOOLS & MATERIALS SCREWDRIVER (Phillips) DRILL PUTTY KNIFE (Optional) CRESCENT WRENCH TAPE MEASURE NECESSARY MATERIALS INCLUDED MATERIALS Water Supply Valve (also known as a water supply stop or water supply fitting) Wax Ring Seat Hardware Kit Not pictured (varies among models) Water Supply Line Tape Silicone (color of your choice) Skirt Mounting Hardware Drain Socket Flange Closet Flange (if the existing closet flange is not used in this installation WAX RING DRAIN SOCKET FLANGE 2
PRECAUTIONS BEFORE INSTALLATION Please note, two people are needed during installation to place the toilet. NOTE: The toilet flange is referred to as the drain socket flange, and the floor flange is referred to as the closet flange for the purposes of this manual. Before installing this product, note the required and recommended water supply line pressure is between 20 and 80 psi. Before installing your new toilet, the rough-in distance needs to be checked.
INSTALLATION Positioning of the Drain Socket Flange 1. Remove the old toilet and the old wax ring with the putty knife. 2. Clean the closet flange thoroughly so there is no leftover residue. 3. Dry fit the drain socket flange (using the existing bolts in the closet flange) and position it so it is straight. NOTE: Do not install the new wax ring in this step. 4. Mark the position of the pilot holes for the drain socket mounting screws at the rear of the drain socket flange. (You will mark 4 holes in total.
INSTALLATION CONT’D Installation of the L-mount Brackets DRAIN SOCKET FLANGE DRAIN SOCKET ANCHOR L-MOUNT BRACKET L-MOUNT ANCHOR 1. Illustration A Measure the thickness of the toilet skirt. It is recommended to add 1/8” to this measurement. Measure this total measurement (thickness of the toilet skirt plus an additional 1/8” as recommended) in from the tape marks made in Step 9 of the previous section. Mark for placement of the L-mount brackets. 2.
INSTALLATION CONT’D Installation of the Toilet 1. Remove the drain socket flange. Attach the new wax ring to the bottom of the drain socket flange. (See Illustration B.) 2. Reinstall the drain socket flange as done in Steps 6-7 of “Positioning the Drain Socket Flange” (on page 4). 3. Attach the water supply line (a steel braided water supply hose is recommended) to the tank filler valve on the toilet. Illustration B 4. Two people are needed to move the toilet into place.
INSTALLATION CONT’D Installation of the Toilet Seat METHOD A (WITH MOUNTING PLATE ): 1. Install the mounting plate bolt for the toilet seat into the mounting hole on the toilet bowl. 2. Turn the mounting plate bolt for the toilet seat with a screwdriver to secure the mounting plate. The tilted surface should face the front of the toilet bowl after you attach the mounting plate for the toilet seat. METHOD B (WITH BOLTS ): 1.
RECOMMENDED MEASUREMENTS 1. The recommended rough-in distance between the center of the closet flange and the wall is 12”. 2. The recommended distance between the center of the closet flange and the water supply valve on the wall is 9” to 11”, depending upon the toilet model. 3. The recommended distance between the water supply valve and the floor is 11.5”. TESTING OPERATION 1. Check the water level in the tank. The water level should reach the waterline for the overflow pipe when the tank is full.
TROUBLESHOOTING & SOLUTIONS Problem 1: The toilet is not flushing Possible Causes: 1. The supply line is blocked 2. The flush button pushrods are not contacting the flush valve. 3. The water supply valve is closed. Solutions: 1. You will need to turn off the water supply and disconnect the supply line. Also, inspect all of the washers. 2. The length of the flush button pushrod needs to be adjusted as needed. 3. Open the water supply valve by lifting the tank filler float and let the toilet tank fill.
PRODUCT WARRANTY The product warranty is a 1 year limited parts warranty from the date it was purchased. There is a warranty statement that accompanies the product. Read the warranty statement for further information on your warranty. CUSTOMER & TECHNICAL SUPPORT For more information and for customer support, contact Jade or our Technical Support Center at 1-866-333-0555 during our business hours (Monday through Friday from 8 am EST to 5 pm EST). 11111 Rue Colbert, Anjou, QC H1J 2S1 www.jadebath.