Foreword Jaguar X-TYPE Driver’s Handbook JAGUAR CARS LIMITED, as manufacturers, are dedicated to the design and production of vehicles which meet the expectations of the world’s most discerning purchasers. To complement the features, systems and technology of your new vehicle we have produced this Driver’s Handbook. In it we have undertaken to make the control of complex systems easy to understand and operate. The information contained herein applies to a range of vehicles and not to a specific vehicle.
Contents 1. Owner information General information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Warnings, Cautions and Notes . . . . . . . . . . . . . . . . . . . 1-2 Health and safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Regular servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Jaguar diagnostic system . . . . . . . . . . . . . . . . . . . . . 1-4 Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4. On the road (continued) Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interior features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sun visors and vanity mirrors . . . . . . . . . . . . . . . . Cigar lighter and ashtray . . . . . . . . . . . . . . . . . . . . Rear centre armrest . . . . . . . . . . . . . . . . . . . . . . . Glove compartment . . . . . . . . . . . . . . . . . . . . . . . Rear sun blind . . . . . . . . . . . . . . . . . . . . . . . .
Contents 7. Maintenance General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Bonnet release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Regular checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Checking and replenishment. . . . . . . . . . . . . . . . . . . . . 7-6 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Windscreen wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17 Tyres. . . . . .
1 Owner information Owner information General information Jaguar Dealers Whether you are new to the Jaguar marque or have previously owned Jaguar or Daimler vehicles, we are pleased that you have made Jaguar your choice of vehicle this time. For safety and the pleasure you will get from your new vehicle, please take the time to get well acquainted with your vehicle by reading the handbooks. Details of the vehicle warranty are contained within the ‘Service Record and Warranty book’.
1-2 Owner information Warnings, Cautions and Notes Vehicle Handbooks Remember to pass on the Vehicle Handbooks when reselling the vehicle. Handbooks are integral parts of the vehicle. Take particular note of WARNINGS, CAUTIONS and Notes given throughout this handbook. ! WARNING: A warning is a procedure which must be followed precisely to help avoid the risk of personal injury.
Owner information Health and safety ! WARNING: 1. Many liquids and other substances used in vehicles are poisonous and should never be consumed and must be kept away from open wounds. These substances include anti-freeze, brake fluid, fuel, windscreen washer additives, lubricants and various adhesives. 2. The presence of any unusual fumes (for example, petrol or exhaust fumes) in the passenger compartment and/or luggage compartment should be corrected immediately by a Jaguar Dealer.
1-4 Owner information Regular servicing Jaguar diagnostic system Vehicle identification Each vehicle is given a full ‘Pre-Delivery Inspection’ to ensure that all systems function correctly and that the vehicle meets its specification. Owners are responsible for the regular maintenance and servicing of the vehicle. Jaguar Dealers will be pleased to arrange periodic servicing and can provide you with details of tasks carried out at each service interval.
Owner information Protect the environment We must all play our part in protecting the environment. Correct vehicle usage and disposal of waste cleaning and lubrication materials are significant steps towards this aim. Avoid using high engine speeds. You will then protect your engine, reduce fuel consumption, lower the engine noise level and help towards reducing the environmental burden. Dispose of batteries, tyres, engine, brake and coolant fluids at your local authorised waste disposal facilities.
1-6 Owner information Touch-screen display Touch-screen use and care A touch-control screen is installed in certain vehicles and provides touch-control of vehicle climate, audio, navigation, television and telephone systems, as fitted. A small LCD screen below the touch-control screen provides digital display of the time, ambient temperature and vehicle cabin set temperature.
Owner information Menu Pressing the ‘MENU’ button will show the ‘SYSTEM MENU’ screen. ‘TV’ is only available in certain countries. If TV is available, see the accompanying TV Handbook for user instructions. The screen display can be blanked out at any time when the ‘SYSTEM MENU’ is in use, by selecting the ‘Screen Off’ touch-control. Touch the screen to restore the menu. Alternatively the Jaguar logo can be displayed by selecting ‘Screen Saver’.
1-8 Owner information ‘VOLUME PRESET’ provides touch-control adjustment of volume associated with the Navigation, Voice control, Phone, Traffic information and Automatic volume control (AVC) systems. Adjustment of AVC varies the rate at which volume is increased or decreased relative to vehicle speed. Press and hold the plus or minus symbol to adjust the volume of the selected function. ‘SET CLOCK’ Clock adjustment is made by pressing the hour or minute, up or down button.
Owner information 1-9 Before using the system SCREEN OFF/SCREEN SAVER The screen display can be blanked out at any time when the ‘SYSTEM MENU’ is in use, by selecting the ‘SCREEN OFF’ touch-control. Touch the screen to restore the menu. Alternatively, the Jaguar screen saver can be displayed. Registration and acquaintance The registration procedure will have been completed by your Jaguar Dealer.
1-10 Owner information Emergency assistance (SOS) The emergency assistance feature allows access to the emergency services (police, fire, or ambulance). Once assistance has been requested, and the vehicle location confirmed, the appropriate services are contacted for assistance to be despatched.
Owner information Call activation and termination Operation will continue even if the ignition is turned off following an activation. Note: Once a call has been initiated, do not attempt to crank the engine as this may cancel the activation. Making an emergency call (SOS) The procedure for obtaining emergency assistance is as follows. • Press and hold the SOS button in the overhead console for 2 seconds or • Touch and hold the SOS button in the touch-screen for 2 seconds.
1-12 Owner information Further information On-screen messages During an assistance call, various status messages are displayed on the radio or navigation screen, which enable the progress of the call to be followed. A list of the messages and their meaning is shown later in this section of the Handbook. While in contact with the response centre, the vehicle location messages (LATITUDE and LONGITUDE) are displayed in sequence, except when the display of another message is required.
Owner information Message list During operation, a sequence of messages will appear on the radio or navigation screen. These are described below.
1-14 Owner information Message list (continued) Message NO CELLULAR SIGNAL Meaning Trying to connect to network WAITING TO ACQUIRE UNABLE TO PLACE CALL Call failed SYSTEM FAULT System failed. See your Jaguar dealer.
2 Security and locks Security and locks Ignition switch The ignition switch, on the right-hand side of the steering column, has four key positions: 0 ___ignition OFF I ___auxiliary II ___ignition ON III __engine start 2-1 Position ‘0’: is the only position in which the key can be inserted and removed. Position ‘I’: allows use of some electrical circuits, for example, radio operation. The airbag system is activated in this position.
2-2 Security and locks Vehicle security When leaving the vehicle unoccupied, remember the following: • Apply the handbrake and with automatic transmission, move the gear selector to Park ‘P’. • Do not leave children or pets in the vehicle unattended. • Do not leave luggage or valuables on view. Always take your valuables with you or lock them in the luggage compartment. • Remove the ignition key and spare keys, even when the vehicle is in your garage. • Close all windows and lock all doors securely.
Security and locks Key transmitter The security system is controlled remotely by a radio frequency, battery-operated, integrated key transmitter. The transmitter is activated by pressing one of the operating buttons. 1. Unlocks and disarms the vehicle. 2. Releases luggage compartment lock. 3. Activates the convenience headlamp feature and sounds the panic alarm. 4. Locks/double-locks and arms the vehicle. 5. Lock/unlock the key. To free the key, press the release button (5).
2-4 Security and locks A Key transmitter battery renewal When the battery needs renewal there will be a significant decrease in the effective range of the key transmitter. To renew the battery, using a small, flat-blade screwdriver, separate and pull the transmitter (A) from the key body. Insert the screwdriver into the groove between the covers (B) and, by twisting the screwdriver, prise the covers apart.
Security and locks Vehicle locking and unlocking Door locks and handles All doors and the luggage compartment can be locked and unlocked using a key transmitter or key. Smart locking This feature helps prevent locking the key in the vehicle. If one of the front doors is open and an attempt is made to lock the doors using a door interior locking lever, all doors will become unlocked. The vehicle can only be locked from the outside by using the key in the driver’s door lock.
2-6 Security and locks Note: 1. If a passenger door is opened during this period, before the vehicle is disarmed, the alarm will sound. 2. Unlocking with the key does not disarm the security system, this provides extra protection against vehicle theft. For all other markets: unlocking the vehicle disarms the alarm system. Global closing ! WARNING: Ensure that all occupants are kept clear of the windows and sunroof aperture.
Security and locks 2-7 With all doors closed, press the lock button on the key transmitter twice within three seconds to double-lock the vehicle and set the alarm. Alternatively, place the key in the driver’s door lock, turn the key towards the front of the vehicle and then towards the rear within three seconds. The exterior direction indicators will flash, once as locking takes place and a longer, second flash as double-locking takes place.
2-8 Security and locks Auto-relocking This feature automatically centrally locks and arms the vehicle if the vehicle has been unlocked with the key transmitter: • and no door has been opened for 45 seconds or • if the ignition remains off for 45 seconds. This feature can be disabled, or reinstated, by a Jaguar Dealer, if required.
Security and locks Alarms and audible signals Note: In certain markets, legislation prohibits the use of audible confirmation signals. In such cases, the sound source has been removed from the system. Audible signals Two horn chirps will sound if an attempt is made to lock the vehicle with the key transmitter if a door, the bonnet or the luggage compartment is not fully closed.
2-10 Security and locks Security features The security system has been designed for: • Prevention of theft of the vehicle • Prevention of theft of items from the vehicle • Personal security The security system is integrated with the vehicle electronics and engine management systems making it far more difficult for a thief to penetrate and steal the vehicle. Intrusion sensing A further enhancement to the security system is the addition of intrusion sensing.
Security and locks Radio frequency approval If the type approval of your key transmitter requires inspection, refer to the table below. Type Exam. Certificate Number: CERT 980154-01 Country Approval No. Country Australia Korea Austria Luxembourg Belgium Netherlands Brazil Norway Chile Portugal Czech Republic South Africa Finland Spain France Sweden Germany Switzerland Israel Taiwan Italy United Kingdom Approval No.
2-12 Security and locks ! HomeLink® Universal Transceiver The HomeLink Universal Transceiver is fitted in the roof console. HomeLink can be programmed to transmit the radio frequencies of up to three different transmitters used to activate garage doors, gates, home lighting, security systems, or other radio frequency operated devices.
Security and locks Press and hold the programmed HomeLink button to activate the programmed device and release when the device begins to activate. If, after 90 seconds, the indicator light does not flash rapidly, release both the HomeLink and the hand-held transmitter buttons and repeat the procedure starting with Step 2. However, position the hand-held transmitter at a different angle and/or distance. If the device does not operate you may need to complete the steps outlined in ‘Rolling code programming’.
2-14 Security and locks Note: The aid of a second person may make the following training procedures quicker and easier. 1. Locate the training button on the garage door opener receiver in the garage. Exact location and colour of the button may vary by garage door opener brand. If there is difficulty locating this button, reference the garage door opener instruction manual or contact HomeLink. Note: Following step 2 there are 30 seconds in which to initiate step 3. 2.
3 Before driving Before driving 3-1 Occupant protection Seat belts The use of front and rear seat belts is mandatory in most countries. Using seat belts saves lives. They should be worn by all occupants whenever the vehicle is in use, for maximum protection. This vehicle has an individual lap/shoulder inertia reel seat belt for each occupant. The inertia operating mechanism of the seat belts allows the wearers to move their upper bodies to reach various controls.
3-2 Before driving Front belt height adjustment To operate: Press the locking button and slide the anchorage point to the required position to ensure comfort and safety. Release the button and check that the anchorage point is locked. Always check the anchorage point after the seat has been adjusted to ensure that the belt is correctly positioned.
Before driving 3. Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. If webbing becomes frayed, contaminated or damaged, discard it and fit a new seat belt. 4. It is essential to renew the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. 5. Belts should not be worn with the webbing twisted. 6.
3-4 Before driving AIR BAG AIR BA G AIR BAG Advanced occupant restraint system In order to provide optimum protection this vehicle is equipped with front and side airbags for driver and front seat passenger. These are supplemental restraint systems which are used in conjunction with the seat belts to help protect the driver and front seat passenger from upper body and head injuries.
Before driving ! WARNING: 1. No objects whatsoever should be attached to the centre cover of the steering wheel, the passenger fascia panel or the sides of the driver and front passenger seats. Do not put anything on or over the airbag inflation area. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. 2.
3-6 Before driving Wrong Unbelted and too close Use Seat Belts Move Seat Rearwards Recline Back of Seat Tilt Wheel Down/Forwards *Belted and 254 mm or more away Correct
Before driving ! WARNING: Driver and front seat passenger should always move their seats as far rearwards as is practical. Ideally, drivers should sit with at least 254 mm between the centre of their breastbone and the cover of the steering wheel airbag. Since the risk zone at the time of deployment is the first 54 mm – 75 mm from the airbag cover, sitting back 254 mm provides a clear margin of safety. Very few drivers are unable to achieve and maintain that safety gap.
3-8 Before driving Front airbags The front airbags use a dual inflation technology and are designed to activate when the vehicle suffers a frontal impact of sufficient force to cause the sensors to close an electrical circuit that initiates airbag inflation. Front airbags use a dual inflation technology which means that, if activated, the bag(s) will deploy at one of two levels of inflation. Sensors monitor the weight on the front passenger seat.
Before driving Side protection The Side Protection system utilizes four airbags: two seat mounted in the front seats, and two curtain airbags located in the upper environment just above the door opening. When the seat mounted side airbag, inflates upon a vehicle side impact, it breaks through the seat bolster stitching, protecting the side of the rib cage of the driver or front seat passenger.
3-10 Before driving Child safety JAGUAR CARS LTD. STRONGLY RECOMMEND THAT AT ALL TIMES CHILDREN SHOULD BE CARRIED IN THE REAR SEATS. In many countries legislation governs how and where children should be carried when travelling in a vehicle. It is the responsibility of the driver to comply with all regulations in force in the country where the vehicle is being used. Holding a baby or child in a person’s arms is not a substitute for a child restraint system.
Before driving Automatic locking retractors All passenger’s seat belts (not the driver’s) have an automatic locking device for use with child seats. The belt, once fitted to secure a child seat with all the slack removed, will automatically lock in this position and further extraction of the belt is inhibited. To activate the static reel (child seat) mode, pull the belt to its full extension to engage the ratchet mechanism.
3-12 Before driving Child restraint tether anchorages and brackets The tether brackets are positioned on the rear parcel shelf at the centre-line of each rear seating position. The child restraint upper tether can be fitted directly to the brackets. Note: Always ensure that child restraint assemblies are fitted in strict accordance with the child restraint manufacturer’s instructions.
Before driving Seat adjustment ! WARNING: 1. Do not make adjustments when the vehicle is moving. 2. Front passengers must not ride with the seat fully reclined. Depending upon the vehicle specification, seats have manual and/or electrical adjustment. Front seat – electrical adjustment A key does not have to be in the ignition switch for seat adjustment. The front seats can be adjusted electrically by two switches on the side of the seat cushion. 3-13 A. controls the seat position.
3-14 Before driving Front seat – manual adjustment Forward and rearward: Each front seat can be adjusted forward and rearward by lifting the locking bar (A), situated below the front of the seat cushion and sliding the seat to the required position. After releasing the locking bar, slight additional seat movement may be necessary to engage the locking mechanism. Height adjustment: The driver’s seat only has a switch (B) to adjust the seat for height.
Before driving Head restraint adjustment ! WARNING: Adjust the head restraint so that it is just behind your head and never behind your neck. Each front head restraint can be adjusted to give the correct height for the seat occupant. The head restraints are height adjustable only, none have swivel adjustment. To lower: press the lever in the escutcheon and push the headrest into the seat back to the required height. To raise: pull the headrest upwards.
3-16 Before driving Front seat heaters Each front seat back and cushion has a heater controlled by a switch on the centre console. With the ignition switch in position ‘II’, press the switch to turn the heaters on. The first press will heat the seat to a high temperature setting, a second press will heat the seat to a lower setting. A third press will turn the seat heater off. A light within the switch will show when the heater is ON, red for the high heat setting and yellow for the lower setting.
Before driving 3-17 If rear electrically operated windows are fitted, button (A) immobilises the rear window switches preventing passengers from operating their windows. The button integral red light will be lit when the rear windows cannot be operated by the rear seat passengers. ! WARNING: 1. When raising windows ensure all occupants are clear. 2. When leaving the vehicle take the ignition keys to prevent misuse of the window switches by remaining occupants, especially children.
3-18 Before driving One-touch operation Each window has a ‘one-touch’ facility enabling the occupant to fully open or close the window in one quick movement. Pulling, or pressing, the switch to its second position and quickly releasing will close or open the window in one movement. Window travel can be stopped at any time by pressing the switch again. Window anti-trap feature Each electrically operated window has an anti-trap feature.
Before driving 3-19 Note: 1. Do not attempt to reposition power fold back mirrors manually. Always use the button. 2. Should a door mirror be knocked out of position the mirror head will be loose. To re-engage the mechanism, power the mirror to the foldback position, then outwards to the drive position. Mirror heating The door mirrors have heating elements which work when the rear screen heater is switched ON. The mirror heater will clear all ice from the mirror surface.
3-20 Before driving Note: 1. Should a mirror assembly become detached from the windscreen, it must be refitted by a Jaguar Dealer. 2. Ensure that the windscreen in front of the mirror is kept clean. Where fitted, the moisture sensor for wiper operation is located to the front of the mirror casing. Any dirt may affect the operation of this sensor. Interior rear view mirror Interior mirrors are either manual dip or electrochromic.
Before driving 3-21 When returning the seat back to the upright position ensure that the seat belts are routed correctly and are not trapped by the seat back. Press the seat back firmly and check that it is locked securely into place. Luggage compartment ! WARNING: 1. Locate heavy loads in the luggage compartment towards the front of the vehicle and secure them to stop them sliding. Loose items can be a hazard. 2.
3-22 Before driving JOL.739 Luggage tie-down loops Four metal loops are positioned in the luggage compartment for attaching straps to secure loads and prevent them from sliding over the luggage floor. These loops are not to be used for securing passengers or animals nor as anchorages for child restraints. A range of Jaguar storage accessories, including a luggage retaining net, are available from your Dealer.
Before driving Ski hatch A two-door hatch is fitted to the rear seat which, when open, gives a space for skis or similar objects to be stowed in the vehicle. Both doors have a single catch. The inner door is accessible after folding down the armrest. To open the door, press the catch (A) downwards and gently lower the door on to the armrest. A bag for retaining the skis can now be pulled from the receptacle into the passenger compartment, and the strap (C) loosened ready to accept the skis.
4 On the road On the road 4-1 Odometer (C) Records the total distance covered by the vehicle. The odometer reading is displayed below the speedometer, along with the trip distance since it was last reset. To reset the trip distance, press the mode button on the end of the left column stalk switch. The trip distance will roll-over at 999.9 kilometres.
4-2 On the road Engine Temperature (E) Warning lights Drive at moderate road and engine speeds until normal operating temperature is reached. This is indicated when the pointer is between the blue (cold) segment and the red (hot) segment. The engine operating temperature will vary with changes in weather and engine load. The engine temperature may rise in some circumstances, such as: • idling for long periods in slow moving traffic. • driving up a long hill in hot weather.
On the road High engine temperature ! WARNING: It is unsafe to run the engine in an overheated condition. The first indication of high engine temperature will be the needle entering the RED zone of the coolant gauge and the illumination of the engine over temperature warning light. If driving, pull to the side of the road and stop the engine when it is safe to do so. Allow the engine to cool. To assist cooling, high engine temperature automatically turns off the air conditioning.
4-4 On the road Charge indicator Seat belt Brake Illuminates when the ignition is ON and should be extinguished when the engine is running. If the light stays ON when the engine is running it indicates that there is an alternator fault. Turn OFF all electrical accessories, radio, climate control, rear screen heater etc. Try to use the minimum electrical load as possible such as power windows, electric sunroof etc. Report the fault to a Jaguar Dealer.
On the road Anti-lock braking system (ABS) If a fault has been detected in the anti-lock brake system (ABS) this light will illuminate. The brake system will continue to function normally, but without ABS braking. Should the light come on or stay on after the bulb check cycle, stop the vehicle at the first opportunity, turn the engine OFF and then restart. If the ABS light comes on again, the vehicle should be driven to a Jaguar Dealer at the earliest opportunity.
4-6 On the road Airbag Main beam Direction indicators If the airbag system develops a fault, the warning light will flash and then come ON and remain on until the fault has been diagnosed and cleared. Report the fault to a Jaguar Dealer immediately. It is safe to drive the vehicle; however, in an accident the airbags may not operate. Illuminates when the main beam headlamps are switched ON or flashed ON.
On the road Low washer fluid level Low fuel reminder Illuminates when the washer fluid level is low. If a message centre is fitted the light will not illuminate but instead a message will be displayed. Illuminates when the fuel level is low. Overspeed warning (Gulf Coast Countries only) Illuminates if the vehicle speed exceeds 120 km/h.
4-8 On the road Audible warnings Various sounds are produced for warning and notification purposes as follows: Hazard or Condition Remedy/chime or tone External lamps remain ON when the driver’s door is opened. A chime will sound until the lights are switched OFF or driver’s door is closed. Note: The chime will not sound if the switch is in Autolamp position. Hazard warning indicators ON. A ticking will sound until the hazard indicators are switched OFF. Left or right direction indicators ON.
On the road The message centre displays: • the total distance covered by the vehicle. • trip computer information. • warning messages if system faults are detected. • status messages to indicate changes in state of certain vehicle functions. Messages Message centre Driver information, messages and data are displayed on the message centre display panel situated within the instrument cluster, when fitted. For the message centre to operate the ignition must be switched ON (position ‘II’).
4-10 On the road Messages The tables on this and the following pages list all messages and warning lights and explains their meaning. Warning Light Priority Indicator LOW BRAKE FLUID LEVEL Brake Red Displayed when the brake fluid level is low. Complete loss of braking may occur. LOW COOLANT LEVEL Low Coolant Level Red Displayed when the coolant level in the reservoir is too low. Check temperature gauge often.
On the road 4-11 Message Warning Light Priority Indicator STABILITY CONTROL FAULT Stability Control Amber Displayed when a fault occurs in the stability control system. STABILITY CONTROL ON or OFF Stability Control Amber Displayed when the stability control system is switched ON or OFF. The warning light will FLASH when the stability control system is switched ON and operating.
4-12 On the road Warning Light Priority Indicator CRUISE CONTROL ON or OFF None None LOW OUTSIDE TEMPERATURE None Red Message Meaning Displayed when cruise control is switched ON or OFF. Frost or ice likely to form on road surfaces. ! WARNING: Even if the message is not displayed there is no guarantee that at low temperatures the road is free from ice. SECURITY FAILED None Red LISTENING None None Displayed when a fault is detected in the security immobiliser system.
On the road 4-13 Trip computer Odometer Average fuel economy (A/B) The computer memory stores data for a journey or series of journeys until it is reset to zero. The displayed information is for guidance only, as it can be affected by traffic, road and weather conditions. Two independent memories are available (A and B) to allow two separate journeys to be recorded concurrently, for example, work usage and evening/weekend usage.
4-14 On the road Setting the trip computer Trip computer switchpack mls/km Pressing the ‘mls/km’ switch alternately displays data in metric or imperial units. A/B Selects either A or B trip memory. Select the required data using the column stalk TRIP button and then pressing A/B will show the A or B information for that data. RESET RESET resets the selected trip to zero. Warning and Information messages have priority over trip data and, if active, will be displayed when the ignition is at position ‘II’.
On the road Clearing messages Messages can be hidden by pressing RESET on the trip computer switchpack. One press will hide one message. Once all messages have been hidden, the display will show trip data, a further press will display the odometer reading. If RESET is pressed again, all active messages will be ‘re-displayed’. Repeatedly pressing the RESET button will cycle through the trip, odometer and message modes.
4-16 On the road Cruise (speed) control The cruise (speed) control system, when fitted, can be used by the driver to maintain a selected vehicle speed above 40 km/h without the driver having to use the accelerator. Illuminated switches on the steering wheel allow the driver manual control of the system. Brake and clutch operation also influences the cruise control system. (A) – RESUME to resume the set speed retained in memory.
On the road Changing the set speed There are three ways to change the set speed: 1. Accelerate or decelerate to the desired speed then press the SET (+) button. 2. Increase or decrease the speed by pressing and holding either SET (+) or (–) until the desired speed is obtained, then release the switch. 3. Increase or decrease the speed in steps of 2 km/h by briefly pressing either the SET (+) or (–) until the desired speed is obtained.
4-18 On the road Exterior lighting Exterior lighting switch A. B. C. D. E. F. OFF side (parking) lights headlights auto front fog lights rear fog lights The exterior lights are controlled by a rotary light switch mounted on the fascia and by the left-hand column switch. The rotary switch has six positions. These are: OFF (A) – All exterior lights OFF (except vehicles provided with daylight running lights).
On the road Auto (D) – A light sensor control, mounted on the front of the interior mirror fixing cover, monitors exterior light levels and automatically switches the sidelights and dipped headlights ON or OFF. The ignition switch must be in position ‘II’ for automatic light operation. When light fades to the non-adjustable, pre-set level, the sidelights and headlights will switch ON automatically. As light increases to the pre-set level, the sidelights and headlights switch OFF automatically.
4-20 On the road Headlight levelling The headlight levelling switch operates when the headlights are switched ON. Push and release the knob to extend it for ease of operation. Push the knob again to place it in the stowed position. Turn the knob to the setting appropriate for the vehicle load, for example: ‘0’ Normal setting – Driver only. ‘1’ Driver and one front passenger. ‘2’ All seats occupied and maximum luggage. ‘3’ Fully loaded vehicle and towing a caravan or trailer.
On the road 4-21 Hazard warning Direction indicators Interior lighting The switch is in the centre console and operates with the ignition ON or OFF. Use only in an emergency to warn traffic of a vehicle breakdown or approaching danger. To operate: Press the switch; the direction indicators, the instrument cluster green indicators and audible warning will operate in unison. The switch symbol will light up. To cancel: Press the switch again.
4-22 On the road Illuminated entry/exit Battery saver When the vehicle is unlocked the courtesy lights will gradually illuminate and remain on for 25 seconds. If the courtesy lights are on they will fade off 25 seconds after the last door is closed, or when the vehicle is locked. If the interior lights are switched on using the centre switch in the overhead console and the ignition switch is turned to positions ‘0’ or ‘I’, the lights will automatically turn OFF after 30 minutes.
On the road Dimmer switch Reverse park control The instruments, door switch packs, in-car entertainment panel and the climate control panel will be lit when the ignition switch is in position ‘II’. Push and release the knob to extend it for ease of operation. Rotate the knob to adjust the illumination to the required level. Push the knob again to place it in the stowed position. Caution: It remains the driver’s responsibility to detect obstacles and estimate the car’s distance from them.
4-24 On the road Sunroof ! WARNING: 1. Before opening or closing the sunroof check that all occupants are clear. 2. When leaving the vehicle take the ignition key to prevent misuse of the sunroof switch by remaining occupants, especially children. The sunroof switch is located in the overhead console. The ignition switch must be in position ‘II’ for the sunroof to operate. To open the sunroof: • push the rear of the switch gently upwards to the first position and hold until the sunroof is fully open.
On the road Windscreen wipers Wipers and washers The windscreen wipers and screen wash functions are controlled by the right-hand column stalk switch and only operate with the ignition in position ‘II’. The stalk functions are as follows: Position (A): Flick wipe. Position (B): The windscreen wipers are Off and parked. First position (C): Intermittent wipe. Second position (D): Slow wiper operation. Third position (E): High speed wiper operation.
4-26 On the road Headlight powerwash Windscreen wash/wipe Push the button on the end of the switch to obtain the wash/wipe programme. If the wipers are selected off or intermittent, the washers will operate at slow speed during the washing action when the button is pressed. When the button is released, the wipers will complete three further wipes. After the wash cycle has been completed the wipers will pause and then complete a drip wipe to clean any remaining drips of moisture from the screen.
On the road Handbrake Horn The handbrake lever, which applies the parking brakes, is mounted on the centre console beside the driver’s seat. Pull the handbrake fully upwards to engage the parking brakes. The handbrake warning/brake fluid low warning light on the instrument cluster will illuminate, if the ignition is on. To release the handbrake, lift the lever slightly, press the locking button at the end of the lever and lower fully.
4-28 On the road Interior features The centre console carries the trinket tray (A) or cup holder (B) and the storage compartment and armrest (C). ! WARNING: 1. Do not place hot drinks in the cup holders whilst the vehicle is moving, there is a risk of scalding. 2. Use soft cups only. Lift the front of the hinged armrest to gain access to the cubby box.
On the road 4-29 Sliding armrest The sliding armrest is hinged at the rear and has two release buttons located on the front of the armrest. Press the right-hand button (A) and lift the top of the armrest to gain access to the top storage compartment, or phone if fitted. Press left-hand button (B) and lift the complete armrest to gain access to the centre console cubby box compartment. Pull the top of the arm rest forwards or push rearwards to slide the armrest to a comfortable position.
4-30 On the road DOLBY B NR Sun visors and vanity mirrors Cigar lighter and ashtray Rear centre armrest Adjustable sun visors can be swung downwards or unclipped and swung sideways to reduce sun glare. The sun visors are fitted with illuminated vanity mirrors, behind a hinged flap. The light comes on when the flap is lifted. Push the lid to gain access to the cigar lighter and ashtray.
On the road Glove compartment A glove compartment is located below the passenger’s airbag. To open the glove compartment, lift the handle and allow the lid to drop down. The compartment will be illuminated when open. If the compartment is left open the lamp will extinguish approximately 30 minutes after the ignition has been set to position ‘0’. The glove compartment can be locked using an ignition key.
4-32 On the road Rear sun blind The manually operated rear sunblind is fitted to the parcel shelf. Using the centre lift point, raise the sun blind and engage the two retaining lugs into their holders in the headlining. To lower the sun blind, holding the centre lift point, carefully disengage the retaining lugs and gently lower the blind into the parcel shelf.
On the road Starting/stopping the vehicle When the vehicle is stationary the automatic gear selector may be left in ‘D’, ‘2’, ‘3’ or ‘4’, unless the vehicle is to be parked. When stopping for traffic lights, junctions etc., either select ‘P’ or apply the handbrake and select ‘N’. Before starting Before starting the engine, new owners/drivers should familiarize themselves with the layout and operation of the controls and instruments.
4-34 On the road If the engine persistently fails to start and flooding is suspected, depress the accelerator pedal fully, hold it in this position and turn the key to position ‘III’ for six seconds. Release the key, remove your foot from the accelerator pedal and then attempt to restart the engine. Note: The engine cannot start whilst the pedal is fully depressed, it must be released to enable the engine to start.
On the road Automatic transmission The ‘J’-gate gear selector lever is designed to accommodate two different driving techniques as follows: • Automatic selection – the right-hand side of the selector gate. • Manual selection – the left-hand side of the selector gate to individually select 4th, 3rd, or 2nd gear. Gear-shift interlock (automatic transmission only) A brake pedal/gear-shift interlock system is incorporated in the automatic gear selector mechanism. To move the gear selector from Park: 1.
4-36 On the road Hill climbing and engine braking When driving on roads with long downhill gradients, selecting ‘3’ or ‘2’ (depending on road/traffic conditions) will give engine braking. When the gear selector is moved from ‘D’, ‘4’ or ‘3’ down to ‘2’, downshift to second gear will only take place at road speeds below 64 km/h. Shift inhibit Reverse is inhibited when the vehicle is moving forward at speeds above 8 km/h. Note: Reverse inhibit will not function in limp home mode.
On the road Sport mode The switch marked ‘S’ on the ‘J’-gate surround enables the driver to select either normal ‘N’ or sport ‘S’ modes. When sport mode is selected the automatic transmission will operate normally, but the gear shift points are extended to make full use of the engine’s power reserves. To select ‘Sport’, press the switch. A red light within the switch is illuminated to indicate that sport mode has been selected. To cancel ‘Sport’, press the switch again.
4-38 On the road Anti-lock braking system (ABS) This system helps to prevent the road wheels from locking and skidding during emergency braking, assisting the driver to maintain full steering and directional stability. The factor controlling ultimate stopping distance and cornering ability is tyre/road adhesion. ! WARNING: 1. It remains the driver’s responsibility to drive safely according to prevailing conditions. 2.
On the road ABS monitoring The ABS control module monitors the ABS electrical system from ignition switch ON to ignition switch OFF. Any malfunction will be indicated by the anti-lock warning light coming on. Should a fault develop in the ABS system, the brake system will still operate conventionally and with the same standard of performance as vehicles not equipped with ABS. Caution: Consult a Jaguar Dealer immediately if the warning light come on while driving, a system failure is indicated.
4-40 On the road Dynamic stability control (DSC) DSC is operational whenever the engine is running, unless it has been switched off. If the system is operating, the warning light in the instrument cluster will flash. The DSC system controls the anti-lock braking system (ABS), traction control and yaw control of the vehicle. Yaw control determines the vehicle’s direction relative to the driver’s inputs (sideslip and under/oversteer).
On the road General driving information ! WARNING: Ensure the handbrake is on and the gear selector is in position ‘P’ or ‘N’ before attempting to start the engine. Before driving off, check the gauges and warning lights and messages. Take special note of any warning light that is on. Seat belts are provided for your safety and it is unwise, and in certain countries illegal, to commence any journey, however short, without wearing them.
4-42 On the road Use of headlamps in daylight Engine oil consumption Winter driving When visibility is poor the headlamps with dipped beam setting should be switched on so that the vehicle may be seen more easily by other road users. The instrument illumination dimmer control adjusts the brightness of the panel lighting. A certain amount of oil consumption is normal. The rate of consumption will depend on the following: • The quality and viscosity of the oil.
On the road Touring Foreign travel Before planning foreign travel, check with a motoring organisation to ensure that your vehicle will comply with legal requirements of the countries you intend to visit. It is advisable to carry vital spare parts to ensure against a breakdown in a remote area. International motoring organisations are helpful for all aspects of long distance touring advice. In some countries it is a legal requirement to carry spare vehicle bulbs.
4-44 On the road Towing a caravan or trailer Your Jaguar Dealer, and the main motoring and caravanning organisations can advise you on towing, towing weight capacities and about regulations that apply in other countries. The following are important points of safety, stability and comfort upon which further advice should be sought: • Maximum braked towing weight is permissible, provided long periods of uphill driving on gradients over 8% are not undertaken.
On the road 4-45 Caution: Vehicles with engines fitted with catalytic converters must only be filled with ‘Unleaded Fuel’. ! Fuel and refuelling Fuel tank filling Before refuelling, switch off the ignition and remove the key. Note: Do not leave the ignition key in the vehicle; vehicles have been stolen from garage service/filling stations whilst the driver is absent from the vehicle. It is recommended that the vehicle is locked, if left unattended.
4-46 On the road The continuous use of high quality fuel makes the need for additional additives unnecessary. This will help to protect the engine components against corrosion, carbon deposit formation and prevent the fuel injection system from clogging. If in doubt your local Jaguar Dealer will advise on which fuel must be used in your vehicle.
On the road Fuels containing alcohol Caution: Take care not to spill fuel during refuelling. Fuel containing alcohol can cause paint damage, which may not be covered under the warranty. Some fuel suppliers sell fuel containing alcohol without advertising its presence. Where uncertainty exists check with the service station operator. Note: Some difficulty in starting may be encountered when using alcohol blended fuel. Ethanol Fuels containing up to 10 per cent ethanol (grain alcohol) may be used.
4-48 On the road Catalytic converters (continued) 4. A correctly tuned engine optimises exhaust emissions, performance and fuel economy and it is recommended that the vehicle is regularly maintained. 5. Do not continue to operate the vehicle if any engine malfunction is evident; malfunctions should be rectified immediately.
5 Climate control Climate control Introduction Recommended operation This vehicle is fitted with one of the following climate control systems: • Manually controlled system with air conditioning. See page 5-4. • Automatic climate control system with an LCD (liquid crystal display) screen. See page 5-7. • Automatic climate control system with touch screen (shared with the navigation and audio systems). See page 5-11.
5-2 Climate control General points To ensure the satisfactory operation of the climate control system, note the following points: • Ensure that the external grille at the base of the windscreen, which provides fresh air for the climate control system, is kept clear of leaves, snow or obstructions. • Vehicles with automatic climate control systems have a solar sensor mounted on top of the fascia on the driver’s side, as shown overleaf (A). Ensure that this sensor is not covered.
Climate control 5-3
5-4 Climate control Manual climate control The manual climate control panel is shown here. The temperature, airflow distribution and volume of air from the interior vents are set using the rotary controls. Push on/push off buttons control the air conditioning, screen heating and fresh or recirculated air. An amber or red LED on each button is illuminated when the selected function is operating. Manual control panel 1. 2. 3. 4. Temperature control Fan speed Air distribution Air conditioning 5.
Climate control The air distribution settings are, from the top clockwise: Temperature Rotating the control knob (1) clockwise from the blue region to the red region increases the temperature of the airflow. The knob may be set to any position for optimum comfort. Air flow directed to windscreen only (A); select to remove frost or heavy misting. Air flow distributed to the windscreen, face and foot levels (B).
5-6 Climate control Air recirculation Air conditioning Windscreen defrost/demist Press the button briefly to select timed air recirculation. To select latched air recirculation, press and hold the button until the LED flashes four times then remains illuminated. To deselect air recirculation and open the fresh air intake, press the button again (LED off). Note that air recirculation cannot be selected in position A (defrost) of the air distribution control.
Climate control 5-7 Automatic climate control with LCD screen The automatic climate control system maintains the interior of the vehicle at the temperature selected by the occupant. The heat input, air conditioning, fan speed, air intake and distribution are adjusted automatically to maintain the desired temperature. Automatic control (AUTO) may be overridden at any time.
5-8 Climate control To switch the system on Temperature selection Air recirculation The climate control system operates in position II (run) of the ignition switch. With the ignition key turned to the run position, the system will switch on in the operating mode last set. For normal usage select AUTO mode. Set the required interior temperature with the red and blue arrowed buttons. Press the red button to increase temperature and the blue button to decrease temperature.
Climate control Windscreen defrost/demist Frost and heavy misting To remove frost or heavy misting from the windscreen, press the DEF button. • The fan switches on automatically at maximum speed but the speed can be reduced manually if required. • Air conditioning switches on automatically and cannot be deselected. • Recirculation is cancelled and cannot be selected. • The front screen heater and the rear screen heater/door mirror heaters switch on automatically, provided the engine is running.
5-10 Climate control Manual air distribution To switch the system off Ram air Air distribution is automatically controlled in AUTO and defrost modes. Press one of the four air distribution buttons to cancel the current mode and select manual operation. The symbol for the selected air distribution will appear on the LCD screen. Press in the fan rotary control knob to switch the climate control system off. If the fan control knob is pressed again, the system will switch on in the previous mode set.
Climate control Automatic climate control with touch screen Operating modes The automatic climate control system maintains the interior of the vehicle at the temperature selected by the occupant. The heat input, air conditioning, fan speed, air intake and distribution flaps are adjusted automatically to maintain the desired temperature. Automatic control (AUTO) may be overridden at any time.
5-12 Climate control Controls Select climate control touch screen Fan speed Air conditioner on/off Automatic operation LCD screen: interior/exterior temperatures and clock 6. Decrease set temperature 7. Increase set temperature 8. Heated rear screen/door mirrors 9. Heated front screen 10.Defrost operation 11.Select recirculated air 12.Touch screen 1. 2. 3. 4. 5.
Climate control Automatic operation cannot be deselected using the AUTO button. To exit AUTO mode, select another climate mode or touch the SYSTEM ON/OFF screen button to switch the system off. Ignition on The climate control system operates in position II (run) of the ignition switch. When the ignition is switched to run or the engine is started, the Jaguar logo will be displayed briefly followed by the last touch screen selected (e.g. radio).
5-14 Climate control External temperature The external (EXT) temperature is displayed on the LCD screen. Celsius/Fahrenheit selection Touch the screen button to change the scale between degrees Celsius (°C) and degrees Fahrenheit (°F) for the displayed internal and external (EXT) temperatures.
Climate control Latched fresh air Windscreen defrost/demist Pressing the air recirculation button when the button LED is illuminated will cancel recirculation and allow fresh air into the vehicle. Deselecting air recirculation cancels AUTO mode. Frost and heavy misting To remove frost or heavy misting from the windscreen, press the DEF button. • The fan switches on automatically at maximum speed but the speed can be reduced manually if required.
5-16 Climate control Air conditioning Fan MUTE Manual air distribution Press the A/C button to switch the air conditioning on or off. The air conditioning system is controlled automatically in AUTO mode. Deselecting A/C cancels AUTO mode. The air conditioning system is also switched on automatically in defrost mode (DEF) but cannot be deselected. To reduce the interior noise level, the fan speed may be quickly reduced to a preset level by touching the MUTE screen button.
Climate control Switching climate control off Ram air To switch the system off, touch the System On/Off button on the CLIMATE CONTROL screen. The touch screen will change to the system off/ram climate control screen above. Pressing the System On/Off button will return the system to the previous state. It is recommended to select AUTO to switch the system on again. With the climate control system switched off, air recirculation is automatically selected (intake flap closed).
6 Roadside emergency Roadside emergency 6-1 Resetting the switch ! WARNING: To avoid the possibility of fire or personal injury, do not reset the inertia switch if you see or smell fuel. If no fuel leak is apparent, reset the inertia switch as follows: 1. Turn the ignition switch to position ‘0’. 2. Pull open the small panel in the trim. 3. Press down the flexible cover on the top of the inertia switch. 4.
6-2 Roadside emergency Emergency starting ! WARNING: 1. It will not be possible to push or tow start a vehicle with automatic transmission. 2. Only jump lead starting or the fitting of a fully charged battery is recommended. Rolling start (manual transmission only) ! WARNING: Because of the dangers to other road users, extreme caution must be exercised when attempting a rolling start.
Roadside emergency 6-3 6. When started, allow the engine to idle for five minutes before disconnecting the cables. 7. Disconnect the black jump lead from the engine mount point and the booster battery negative (–) terminal. 8. Disconnect the red jump lead from the positive (+) terminals of both batteries. 9. Refit the battery box cover. Emergency starting using jump leads (continued) The following procedure must be followed exactly, being careful not to cause sparks: 1.
6-4 Roadside emergency Wheel changing and jacking Be prepared for a flat tyre. Know where equipment is stowed and read the wheel changing and jacking instructions carefully. Pull off the road completely, clear of all traffic and park on as level, solid ground as possible. Switch on hazard warning lights and, where legally required, display the warning triangle. ! WARNING: It can be dangerous to change a wheel when the vehicle is on a slope or soft, uneven ground.
Roadside emergency Temporary-use spare wheel Locking wheel nuts Observe the following warnings before using the wheel. Some vehicles are fitted with one locking wheel nut on each wheel. These can only be removed using the extractor tube and key socket located in the luggage compartment. The locking wheel nut has a cover which makes it visually similar to standard wheel nuts. The top of the cover has an indentation (A) to aid identification.
6-6 Roadside emergency Wheel changing Caution: 1. Ensure that all passengers are in a safe place, clear of the vehicle. 2. Firmly apply the handbrake. 3. For automatic vehicles, select gear position ‘P’ (Park). 4. For vehicles with manual transmission, select a low gear. 5. Ensure that the jack is placed on firm and level ground.
Roadside emergency 6-7 When changing the alloy road wheels, transfer the centre badge to the replacement wheel (when a full-size spare wheel is used). Using the rounded end of the wheel nut wrench handle from the inside of the wheel, push the centre badge from its housing. Push the centre badge into the replacement wheel. If the temporary-use spare wheel is to be fitted, keep the centre badge safely and fit it to the repaired full-size wheel when it has been refitted.
6-8 Roadside emergency At the earliest opportunity have the wheel nuts tightened with a torque wrench to: Alloy wheels: • 103 Nm ± 15.5 (75.95 lb.ft. ± 11.4). Steel wheels: • 80 Nm ± 12.0 (9.0 lb.ft. ± 8.5). This torque must not be exceeded. Fit the spare wheel and loosely secure with the wheel nuts. Using the wheel nut wrench, lightly tighten the wheel nuts alternately using the sequence shown in the illustration. Lower the jack and tighten the wheel nuts alternately, DO NOT OVERTIGHTEN.
Roadside emergency Vehicle recovery Caution: The preferred and recommended vehicle recovery method is by using a flat bed transporter. The removable towing eye is primarily for emergency use when towing for SHORT DISTANCES, e.g. removing the vehicle if it is causing an obstruction or for winching the vehicle onto a recovery transporter. Caution: • Do not tow the vehicle with the front wheels lifted unless the propshaft to the rear wheels is disconnected at the final drive flange.
6-10 Roadside emergency Transporting When the vehicle is being transported on a trailer or vehicle flat bed transporter, the handbrake must be applied, the wheels chocked and: • the automatic gear selector lever moved to position ‘N’ or ‘D’ but NEVER to ‘P’. • the manual gear selector lever moved to the neutral position. The vehicle must be securely tied down to the transporter or trailer. There are four transporter tie-down brackets on the vehicle underbody.
Roadside emergency Towing eye A towing eye is provided in the luggage compartment with the jack. Caution: • The towing eye is not suitable for ‘solid bar’ towing • Care must be taken to avoid damaging the bumpers and front apron. The front towing point is located at the right-hand side of the vehicle, in the grille. To prevent damaging them, the grille vane and the small cover on the left-hand side of the grille must be removed. Pull the grill vane to remove it from the vehicle.
6-12 Roadside emergency Bulb renewal It is important that only Jaguar bulbs of the type specified are used when renewing bulbs. Before renewing bulbs, switch off the ignition and light switches. Caution: Halogen type bulbs will be damaged if touched by hand or contaminated with oil or grease. It is important to use clean gloves or cloth when handling a bulb which is to be used again. A contaminated bulb may be cleaned with methylated spirit before refitting. Main beam (inner) headlight Open the bonnet.
Roadside emergency 6-13 Dip beam (outer) headlight Side repeater indicator – bulb renewal Open the bonnet. Slide open the two spring clips and remove the cover. Turn the bulb holder a quarter turn anti-clockwise and remove the bulb and holder from the light unit. Fit a new bulb to the holder, type H1 for dipped beam. Fit the holder to the light unit, the bulb will only correctly fit in one position. Fit the cover and retain using the two spring clips. Close the bonnet.
6-14 Roadside emergency Front parking (side) light – bulb renewal Front direction indicator – bulb renewal Number plate light – bulb renewal Open the bonnet. The front parking lights are contained within the outer headlight units. Slide open the two spring clips and remove the cover. Rotate the bulb holder anti-clockwise and remove from the headlight. Pull the capless bulb from the holder and fit a new one of the correct type, W5W. Reposition the bulb holder in the headlight unit and turn clockwise.
Roadside emergency 6-15 Rear light assembly – bulb renewal The rear light assembly has the following bulbs: 1. Reverse light, type P21W. 2. Stop/tail light, type P21/5W. 3. Fog light, type P21W. 4. Tail light, type P21/5W. 5. Direction indicator, type PY21W. Ensure that the lights and ignition switch are OFF before removing any bulbs. Open the luggage compartment, loosen the side carpet and unclip the rear light bulb carrier.
6-16 Roadside emergency Fuses and fuse boxes Fuse failure is identified by an inoperative circuit. Do not fit a new fuse if the wiring is damaged; contact a Jaguar Dealer. After renewing a fuse have the circuit checked by a Jaguar Dealer. Two types of fuses are fitted in the fuse boxes, a mini-type (A) and a cartridge-type (B). A special tool for removing and replacing the mini-fuse is provided in the engine compartment fuse box lid, together with spare fuses. Use only the spare fuses supplied.
Roadside emergency Mini-fuse replacement Push the tool on to the suspect mini-fuse and withdraw it. If the wire in the fuse is broken, the fuse has blown. Fit a new fuse using the tool. Cartridge fuse replacement Pull the suspected blown fuse from its holder. If the wire in the fuse is broken, the fuse has blown. Push a new fuse into the holder. ! WARNING: 1. Do not fit a fuse of a different amperage from that removed.
6-18 Roadside emergency Left-hand drive vehicles For fuse box visual access, remove, by unclipping/pulling, the sunglasses stowage compartment, to the left of the steering column. Remove the lower panel on the knee bolster below the sunglasses stowage compartment to gain hand access to the fuse box. A torch or flashlight will be required to properly identify the fuses. JOL705 Engine compartment fuse box The fuse box is located in the engine compartment on the left-hand side adjacent to the battery.
Roadside emergency Fuse and Relay Positions A – Engine compartment fuse box B – Passenger compartment fuse box 6-19
6-20 Roadside emergency Engine compartment fuse box – fuses Fuse No Fuse Type Rating (amps) Colour F1 cartridge 20 Blue Dip beam, High Intensity Discharge (HID) light relay. F2 cartridge 50 Red Ignition relay feed. F3 cartridge 60 Yellow F4 cartridge 30 Pink Rear window heater relay, heated mirrors. F5 cartridge 30 Pink Auxiliary vacuum pump, transmission control module. F6 cartridge 30 Pink Heater blower relay.
Roadside emergency Fuse No Fuse Type Rating (amps) Colour F18 Circuit Not used. F19 Diode D1 Not used. F20 Mini 5 Tan Navigation display. F21 Mini 15 Blue Master lighting (Park lights). F22 Mini 20 Yellow F23 Mini 10 Red Air conditioning compressor clutch relay. F24 Mini 15 Blue Door lock power. F25 Mini 15 Blue Direction indicators (GEM). F26 Mini 15 Blue Horns relay. F27 Mini 10 Red Transmission control module, transit relay.
6-22 Roadside emergency Fuse No Fuse Type Rating (amps) Colour F36 Mini 10 Red Canister purge valve, canister close valve, airflow meter, throttle motor relay, power wash relay coil, air conditioning relay coil. F37 Mini 15 Blue Engine management system, fan speed controller, speed controller. F38 Mini 30 Green F39 Mini 5 Tan F40 Mini F41 Mini 10 Red F42 Mini 30 Green Circuit Oxygen sensor heaters A. Variable intake valves. Not used. Injectors. Oxygen sensor heaters B.
Roadside emergency Engine compartment fuse box – relays Fuse No Fuse Type Rating (amps) Colour R1 ISO 40 A 40A Black Windscreen wipers. R2 ISO 70 A 70A Grey Heated front windscreen. R3 Micro 20 A 20A Black Horn. R4 Micro 20 A 20A Black Accessories. R5 Micro 20 A 20A Black Headlight powerwash. R6 Micro 20 A 20A Black Air conditioning compressor clutch. R7 ISO 70 A 70A Grey Engine management system. R8 Micro 20 A 20A Black Transmission control module.
6-24 Roadside emergency Passenger compartment fuse box – fuses Fuse No Fuse Type Rating (amps) Colour F60 Mini 20 Yellow Power windows left-hand. F61 Mini 20 Yellow Power windows right-hand. F62 Mini 10 Red Rear fog lights. F63 Mini 10 Red Right-hand – front side light, side markers, rear tail lights. F64 Mini 10 Red Left-hand – front side light, side markers, rear tail lights.
Roadside emergency 6-25 Fuse No Fuse Type Rating (amps) Colour F75 Mini 10 Red F76 Mini F77 Mini 10 Red Screenwash pump, rain sense. F78 Mini 5 Tan Phone power supply, VEMS. F79 Mini 10 Red Reverse lights, reverse light switch, reverse park aid, electrochromic mirror, instrument cluster. F80 Mini 10 Red Park interlock, heater switch, OBD2, blower relay. F81 Mini 20 Yellow Fuel pump.
6-26 Roadside emergency Fuse No Fuse Type Rating (amps) Colour F91 Mini 10 Red Sunroof, electrochromic mirror, left and right-hand power windows. F92 Mini 10 Red Manual transmission cruise control switch, ignition coils, automatic transmission rotary switch. F93 Mini 30 Green Windscreen wipers. F94 Mini 20 Yellow HID module. F95 Mini 10 Red Airbag restraints module. F96 Mini 10 Red ABS module.
Roadside emergency Passenger compartment fuse box – relays Relay No Type Rating (amps) Colour R15 Micro 20 A 20A Black High beam/front fog lights relay. R16 Micro 20 A 20A Black Not used. R17 Micro 20 A 20A Black Reverse lights. R18 ISO 70 A 70A Grey Ignition relay. R19 ISO 40 A 40A Black Heated rear window relay. R20 ISO 40 A 40A Black Blower relay. R21 Micro 20 A 20A Black Battery saver relay.
7 Maintenance Maintenance General maintenance Precautions • Ensure that the vehicle is securely supported before working underneath it. Chock a front wheel and apply the handbrake. • Whenever possible use a suitable wheel-free lift when working beneath the vehicle. If a jack is used to support the vehicle, use axle stands carefully placed at the jacking points to provide a rigid support. Only use jacking equipment at the designed lifting points.
7-2 Maintenance General precautions against damage • When working in the engine compartment protect the exterior paintwork by using suitable covers over the wings and scuttle. • To prevent soiling the interior, carry out jobs requiring access to the passenger or luggage compartments first. If a job involves access to the interior in the course of other work, prevent the transfer of oil and grease to the interior by using seat and carpet covers and wearing clean overalls and gloves.
Maintenance Bonnet release ! WARNING: Take care to keep away from rotating components if the engine is running when you open the bonnet. Release the bonnet lock by pulling the lever below the fascia on the driver’s side of the vehicle. Lift the bonnet slightly and pull up the safety catch under the bonnet, located centrally behind the grille. The gas filled struts will assist raising the bonnet, and retain it in the fully open position.
7-4 Maintenance Regular checks In the interests of safety and reliability, it is advisable to carry out the following checks at the recommended intervals, and always before starting on a long journey. Daily Check that there is sufficient fuel for the journey intended, particularly at night and before entering motorways. Weekly Tyres – Check the tyres, including the spare, for condition and pressure. Tyre pressures are shown inside the front cover of this handbook.
Maintenance Reservoir and dipstick locations 1. Power steering reservoir 2. Engine oil dipstick 3. Engine oil filler 4. Windscreen wash reservoir 5. Brake/clutch reservoir 6.
7-6 Maintenance Checking and replenishment Check engine oil level Check the oil level regularly with the vehicle on flat, level ground. Refer to page 7-5 for dipstick and oil filler locations. It is preferable to check the oil level after the vehicle has been standing, that is, with the engine completely cold. If the engine has been started do not check the oil level until the engine has reached normal operating temperature.
Maintenance Recommended engine oil When the oil level is at the lower dipstick mark, add 1.0 litres of oil: Oil specification – API SJ / EC and ACEA A1-98 or A3-98.
7-8 Maintenance Check power steering fluid level Caution: It is imperative that the power steering system does not become contaminated in any way. Always dispense fluid from a fresh sealed container and clean the area around the reservoir neck both before and after replenishment. Never return drained fluid to the system. Refer to page 7-5 for power steering fluid reservoir location. Check the fluid level when the engine is ‘COLD’ and the vehicle is on a flat, level surface.
Maintenance Check brake/clutch fluid reservoir The manual transmission clutch fluid is shared with the brake fluid in a common reservoir. ! WARNING: The fluid level will drop as the brake pads wear. If the level is very low report the loss of fluid to the nearest Jaguar Dealer. Do not drive the vehicle until the cause is rectified. Caution: 1. While handling brake fluid, take extreme care; brake fluid must not contact the vehicle paintwork. 2. Always use fresh, clean fluid from a new container.
7-10 Maintenance Check windscreen washer reservoir Refer to page 7-5 for windscreen washer reservoir location. The washer reservoir contains the fluid for the windscreen washers and the headlamp powerwash system (where fitted). Fill to just below the neck with Jaguar Windscreen Washer Fluid diluted with clean, preferably soft water as specified in the instructions on the bottle. Do not over-fill.
Maintenance Check coolant level The coolant level must only be checked when the engine is COLD. Refer to page 7-5 for coolant header tank location. ! WARNING: Do not remove the coolant header tank filler/pressure cap while the engine is hot. If the cap must be removed, protect the hands against escaping steam and slowly turn the cap anti-clockwise until the steam pressure starts to escape. Leave the cap in this position until the pressure is released, and then remove the cap completely.
7-12 Maintenance Engine anti-freeze Anti-freeze, when used at the correct concentration, not only protects the engine from frost damage in winter, it also provides all year round protection against internal corrosion. The cooling system should be filled or replenished with a mixture of 50 per cent water and 50 per cent anti-freeze, conforming to specification: WSS M97B44, coloured orange, Extended Life Coolant. This mixture gives frost protection for temperatures down to -40°C.
Maintenance Capacities Litres Engine oil, including oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,7 The rear axle (final drive unit), transfer box and automatic and manual transmission units (gearboxes) will not normally require to be checked or replenished. Cooling system, including reservoir and climate control . . . . . . . . . . . . . . . . . 8,25 Windscreen washer reservoir – without headlamp powerwash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-14 Maintenance Battery A low maintenance battery specifically designed for use with this vehicle is fitted in the engine compartment. ! WARNING: 1. The cell plugs and vent pipe must be in place at all times when the battery is in the vehicle. Failure to fit, or incorrect fitting of these items is potentially hazardous. 2. To avoid injury do not use an open flame or cause an electric spark when checking the battery. Hydrogen gas generated by the battery is flammable and may explode. 3.
Maintenance 7-15 Check/replenish battery electrolyte Battery charging Note: In normal climates this must be carried out at least once a year. In hot weather/climates the electrolyte level must be checked at least every three months. Open the bonnet and remove the battery cover. Unscrew the six cell plugs. Check that the electrolyte is level with the plastic level indicator (A). If necessary, replenish with distilled water but do not overfill.
7-16 Maintenance Battery lead disconnection Note: • Upon battery lead reconnection the radio security code will be required and the clock will need to be reset. • Electrically operated door windows must be reset to learn the anti-trap function. • If the battery is disconnected for more than 72 hours the radio preset channels will need to be reset upon battery reconnection. • The trip computer will lose all recorded trip data and all trip functions will be reset to zero.
Maintenance 7-17 Windscreen wipers Wiper blade renewal Note: 1. The wiper blades will be renewed at every service interval. 2. Use Jaguar Screen Clean Paste to remove contamination from the windscreen to ensure effective wiping or if smearing or juddering becomes evident. A more aggressive cleaning agent may be required to remove stubborn contamination. Contact a Jaguar Dealer for advice.
7-18 Maintenance Tyres Tyre renewal Tyre pressures Tyres of the correct type, manufacturer and dimensions, with correct cold inflation pressures are an integral part of every vehicle’s design. Regular maintenance of tyres contributes not only to safety, but to the designed function of the vehicle. Road-holding, steering and braking are especially vulnerable to incorrectly pressurised, badly fitted or worn tyres.
Maintenance Wear All tyres fitted as original equipment include tread wear indicators (TWI) in their tread pattern. When the tread has worn to a remaining depth of 1,6 mm the indicators appear at the surface as bars which connect the tread pattern across the full width of the tyre. It is illegal, in certain countries, to continue to use tyres after the tread has worn to less than 1,6 mm over three quarters of the width and the entire circumference of the tyre.
7-20 Maintenance Winter (snow) tyres The tyres fitted as original equipment are designed with a rubber compound, tread pattern and width specially suited for high speeds in normal road conditions, but they are less suitable during extremes of low temperatures, snow and ice. The use of winter tyres will considerably improve the vehicle’s handling during these conditions.
Maintenance Vehicle care Valet kit A valet kit containing a selection of Car Care products is available from the Jaguar accessory range. Interior care Brush and clean the interior regularly. Use a vacuum cleaner where possible to remove all dust from the interior and trim. Carpets Marks or stains can be removed by gentle scrubbing with a weak solution of soap and warm water. For more stubborn stains a commercially available carpet cleaner should be used. See your Jaguar Dealer for advice.
7-22 Maintenance Mop up excess liquid with absorbent tissue (preferably white) or absorbent cloth; scoop up dry solids. Work inwards from the edge of the stain to prevent spreading. Use small amounts of cleaning liquid, blotting between applications. Work slowly and thoroughly using light pressure. If the stain cannot be removed, contact a reputable dry cleaners. ! WARNING: Dry Cleaning Fluids may be toxic or flammable. Take adequate precautions when handling these products.
Maintenance The following products will ensure glass surfaces and windscreen wipers are kept in good condition: Jaguar Screen Clean Paste – Apply to the exterior of the windscreen only to ensure effective operation of the windscreen wiper. Jaguar Glass Cleaner – Interior and exterior of all other glass surfaces. Jaguar Screen Wash – Washer reservoir additive. Jaguar Winter Care Kit comprising de-icer, ice scraper, anti-mist wipe cloth and aerial cleaner – for use in adverse weather conditions. Note: 1.
7-24 Maintenance Electrical accessories ! WARNING: Alterations to the electrical system, including the fitting of accessories not designed for this Jaguar, will cause damage to the electrical circuits and systems. In some circumstances this could result in a malfunction or fire. All accessory work should be entrusted to a Jaguar Dealer. The cigar lighter sockets can be used for plug-in accessories which are only temporarily connected to the vehicle (for example, a car vacuum cleaner). Caution: 1.
8 Specifications Specifications 8-1 Vehicle data Engine 2.5 litre 3.0 litre Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V6, dual overhead camshafts, 4 valves/cylinder V6, dual overhead camshafts, 4 valves/cylinder Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2495 cm3 2967 cm3 Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81.6 mm 89 mm Stroke .
8-2 Specifications Weights (average/approximate) Gross combination weight is the gross vehicle weight plus recommended trailer weight. Vehicles with automatic transmission Vehicles with manual transmission kg kg Kerb weight, no options fitted . . . . . . . . . . . . . . . . . . . . . 1595 1555 Front axle kerb weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 970 935 Rear axle kerb weight. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 8-3 Roof-rack capacity and trailer weights kg Roof-rack capacity including weight of rack . . . . . . . . . . . . . . . . 80 Maximum permitted luggage compartment load with four passengers and driver . . . . . . . . . . . . . . . . . . . . . . . . . 60 Trailer weight: Braked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500 Unbraked (maximum recommended) . . . . . . . . . . . . . . . . . . . . . 750 Trailer nose load . . . . . . . . . . . .
8-4 Specifications Dimensions mm Overall length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4672 Overall width including mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2003 Overall width without mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782 Overall height (at gross vehicle weight). . . . . . . . . . . . . . . . . . . . . . . 1392 Wheelbase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications Wheels and tyres Wheel size/type Tyre size/manufacturer 6.5" x 16" 5 Spoke Alloy 205/55R16 Pirelli or Continental 6.5" x 16" 10 Spoke Alloy 7.0" x 17" Double 5 Spoke Alloy 225/45R17 Pirelli 6.
8-6 Specifications Tow-bar fixing points The rear longitudinal members are factory pre-marked (A) for drilling for tow-bar mountings.
Index Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Alarms and audible signals . . . . . . . . . . . . . . . . . . . . . . . . 2-9 – audible signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 – error signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 – full alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Alloy wheels – care of . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Daylight running lights . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Dimensions – vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Dimmer switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Direction indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Door guard/puddle lamps . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Door locks and handles . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Health and safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 HomeLink® Universal Transceiver . . . . . . . . . . . . . . . . . 2-12 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 I Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Illuminated entry/exit . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Inclination (tilt) sensing . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Message centre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 – clearing messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 – illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 – messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Mirror – heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19 – interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Temporary-use spare wheel . . . . . . . . . . . . . . . . . . . . . . . 6-5 Touch-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Touring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43 Tow-bar fixing points . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Towing a caravan or trailer . . . . . . . . . . . . . . . . . . . . . . . 4-44 Towing eye . .
Index Window tinting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Windscreen – cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22 – washer/powerwash fluid – check/replenish . . . . . . . . . 7-10 – wipers/washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 – wipers/washers – maintenance . . . . . . . . . . . . . . . . . . . 7-17 Winter driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42 Winter tyres . .
JJM 21 02 20/15