- Jai Progressive Scan Camera Operation Manual Model CV-M10

ManualsBrandsJAI ManualsSecurity CameraCV-M10

Operation Manual

Progressive Scan Camera

(Rev.F)

CV-M10

Summary of content (24 pages)

PAGE 1
Progressive Scan Camera CV-M10 Operation Manual (Rev.
PAGE 2
CV-M10BX/CV-M10RS DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPATIBILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLLOWING PROVISIONS APPLYING TO IT.
PAGE 3
CV-M10BX/CV-M10RS Table of Contents 1. General .............................................................................................................................................................................. 1 2. Standard Composition ....................................................................................................................................................... 1 3. Main Features ............................................................................................
PAGE 4
CV-M10BX/CV-M10RS 1. General The CV-M10 is a compact monochrome progressive scan camera designed for automated imaging applications. The 1/2" CCD with square pixels offers a superb image quality. The high-speed shutter function and asynchronous random trigger mode allows the camera to capture high quality images of fast moving objects. The dual tapped video output allows the camera to operate with a high frame rate.
PAGE 5
CV-M10BX/CV-M10RS 4. Locations and Functions 3 5 6 4 8 7 1 2 9 CV-M10BX 1. 2. 3. 4. 5. 6. 7. 8. 9. Lens mount of C-mount type. *1) Interline-transfer CCD sensor with on-chip micro lenses. Video output 1. VS 1.0 Vp-p. *2) Video output 2. VS 1.0 Vp-p. (Only in 2 :1 interlaced mode.) *2) SW1 switch on the rear panel to set the shutter speed and other function modes. 6 pin connector for RS 232C signals, input of external trigger pulse and WEN output.
PAGE 6
CV-M10BX/CV-M10RS 5. Pin Assignment 5-1. 12-pin Multi-connector (DC-IN/SYNC.) Type: HR10A-10R-12PB-01 (Hirose) male seen from rear. 9 1 2 8 10 11 3 4 5 Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 7 12 6 Signal GND +12 VDC input GND Video 1 output GND HD input/output VD input/output GND Video 2 output GND +12 V DC input GND Remarks Parallel with the BNC video 1 output. Avoid double termination. Ext. HD in as factory setting. *1) Ext. VD in as factory setting. *1) *2) Video 2 only in 2:1 interlace.
PAGE 7
CV-M10BX/CV-M10RS 6. Functions and Operation Apart from the standard continuous operation, the CV-M10 features two external asynchronous trigger modes, Edge Preselect and Pulse Width Control mode. These 2 external trigger modes can operate with either H reset or H non-reset. In Edge Pre-select and H reset, the internal HD is reset on the falling edge of the trigger and the exposure starts. For Pulse Width Control and H reset, the rising edge of the trigger will stop the exposure and reset the internal HD.
PAGE 8
CV-M10BX/CV-M10RS 6.3. External Trigger Mode External trigger mode of CV-M10 allows 2 different driving modes: 1 Edge Pre-select mode. (Asynchronous reset and exposure start by an ext. trigger) 2 Pulse Width Control mode. (Exposure control by the low period of the ext. trigger) For both there are two trigger modes. H reset and H non-reset. H non-reset mode allows input of synchronized external trigger and external HD.
PAGE 9
CV-M10BX/CV-M10RS The resulting video signal will start to be read out after the trigger rising edge. The WEN pulse indicates the start of valid video signal. Refer to timing charts for details. A new trigger pulse must not be applied before the video read out has been finished. To use this mode: Set: SW1-4 on BX rear to OFF for random trigger. For RS select trigger mode JP12 on PK8206 (BX ver.) or PK8190 (RS ver.) Short for Pulse Width Control JP13 on PK8206 (BX ver.) or PK8190 (RS ver.
PAGE 10
CV-M10BX/CV-M10RS 6.5.
PAGE 11
CV-M10BX/CV-M10RS 7. Mode Settings 7.1. Mode Setting by Switch The mode setting switch SW1 on rear for CV-M10BX and CV-M10RS is different for switch SW1-1 to SW1-3 and SW1-7 to SW18. For BX the shutter values can be selected in 3 ranges depending of the internal SW1 on the PK 8206 board. The switch select between Normal, High speed or Low speed. In the following the switch settings are shown. < 1 2 3 4 < OFF ON 7.1.1.
PAGE 12
CV-M10BX/CV-M10RS 7.2. Shutter Time select. Before making any mode or jumper settings switch the power off. The shutter select is for CV-M10BX done with the internal SW1 on PK8206 and SW1 on rear. For CV-M10 RS only the normal shutter range can be selected by the SW1 on rear. The high speed and low speed range can only be selected by RS 232C. 7.2.1. CV-M10BX SW1 on PK8206 For CV-M10BX the internal SW1 on PK8206 can select the following shutter modes.
PAGE 13
CV-M10BX/CV-M10RS 7.4.2. Non interlaced mode With SW1-5 ON the camera is in non-interlaced mode. The video is read out on video 1 as a full progressive scanned frame. The frame rate can be up to 25 for CCIR and 30 for EIA. 7.5. Gamma Correction SW 1-6 will select the gamma correction. OFF is gamma 1.0, which is linear and normally used for vision. ON is gamma 0.45, which is non-linear. 7.6. Gain Control/RS 232C control SW1-7 and SW1-8 has different functions on CV-M10BX and CV-M10RS. 7.6.1.
PAGE 14
CV-M10BX/CV-M10RS 8. Jumper settings Switch off the power before making any mode or jumper settings. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD input is factory setting) Termination of HD/VD input. (75 ohm is factory setting.) Trigger input termination. (Factory setting is TTL) Trigger mode select. (Edge Pre-select is factory setting) H-reset or H non-reset. (Fatory setting is H reset.) Alternative pins for inputs/outputs.
PAGE 15
CV-M10BX/CV-M10RS 8.6. Locations of Jumper Jumpers positions are shorted with a 0 ohm resistor or by a soldering between the 2 points. To remove the solder tin from a jumper position, use a special tin remover such as desolder wick. 8.6.1. Location of Jumper on PK8189A On this board the jumpers for HD/VD input, output and 75ohm termination are found. JP6 JP3 JP4JP5 JP1 JP7 8.6.2. Location of Jumper on PK8187A On this board the jumpers for alternative outputs on the 12 pin connector are found.
PAGE 16
CV-M10BX/CV-M10RS 8.6.3. Location of Jumper for CV-M10BX on PK8206A Jumpers for selecting random trigger modes for CV-M10BX. It is edge pre-select, pulse width control, H reset and H nonreset. Jumper for trigger input 75 ohm termination is also found here. JP10 JP13 JP12 8.6.4. Location of Jumper for CV-M10RS on PK8190A Jumpers for selecting random trigger modes for CV-M10RS. It is edge pre-select, pulse width control, H reset and H nonreset. These modes can not be selected by RS232C.
PAGE 17
CV-M10BX/CV-M10RS 9. Internal adjustments on BX For CV-M10BX there are internal potentiometers for adjusting the two video outputs. Do not touch these adjustments unless you are familiar with video camera adjusting. The potentiometers are found on the PK8206A board in CV-M10BX. For CV-M10RS the same adjustments can be done via RS232C with the camera control tool. See "10. CV-M10RS Camera Control Tool." The adjustments are for the following functions: Black level.
PAGE 18
CV-M10BX/CV-M10RS 10. CV-M10RS Camera Control Tool A camera control tool for CV-M10RS is available. It runs under Windows 98 and NT. After installation a bar is shown on the screen. From here windows for each function group can be opened for camera control. In the following the bar and windows are shown. 10.1. Control Bar for CV-M10RS Camera Control 10.2. About and Help Window 10.3. Shutter Window 10.4.
PAGE 19
CV-M10BX/CV-M10RS 10.5. Levels Window 10.6. Files and Camera 10.7.
PAGE 20
CV-M10BX/CV-M10RS 11. External Appearance and Dimensions Unit : mm (inch) 5 50 (1.97) 4-M3 (1.02) 26 (0.2) 50 80 12.7 (0.5) 26 6 (1.02) (3.15) (1.57) 40 (1.
PAGE 21
CV-M10BX/CV-M10RS 12. Specifications Model CCD Sensor Image Area Number of Elements Cell Size Scanning System Vertical Frequency Horizontal Frequency Synchronization Resolution S/N Ratio Sensitivity Ext. trigger mode Electronic Shutter Random Trigger Shutter Gamma Gain Video Output Lens Mount Interface Environment Power Consumption Dimensions Weight CV-M10 1/2" Interline-Transfer Type 6.4mm (H) x 4.8mm (V) 659(H) x494(V) EIA/VGA corresponded782(H) x 582(V) CCIR 9.9µm(H) x 9.
PAGE 22
CV-M10BX/CV-M10RS 13. Appendix 13.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this camera. Do not expose this camera to rain or moisture. Do not face this camera towards the sun, extreme bright light or light reflecting objects.
PAGE 23
CV-M10BX/CV-M10RS 11. User’s Record Camera type: CV-M10BX/CV-M10RS CCIR/EIA Revision: (Revision F) Serial No. ................. Users Mode Settings Users Modifications 15. Index No index.
PAGE 24
2700- 11052 E F3 0901 JAI A·S, Denmark Produktionsvej 1, 2600 Glostrup Copenhagen, Denmark Phone +45 4457 8888 Fax +45 4491 8880 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Yokohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.jai-corp.co.jp JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.