Full Product Manual

ManualsBrandsJames Hardie ManualsBuilding materialsHardiePlank HZ10 5/16 in. x 8 in. x 144 in. Fiber Cement Custom Colonial Lap Siding

General

Product

Information

Tools for

Cutting and

Fastening

General

Installation

Requirements

General

Fastener

Requirements

Finishing and

Maintenance

HardieTrim

Boards/Battens

HardieWrap

Weather Barrier

HardieSofﬁt

Panels

HardiePlank

Lap Siding

HardieShingle

Siding

HardiePanel

Vertical Siding

ESR-1844 &

2290 Report

Appendix/

Glossary

Working

Safely

HardiePlank

Lap Siding Product Description

HardiePlank lap siding is factory-primed ﬁber-cement lap siding available in a variety of styles and textures. Please

see your local James Hardie

product dealer for product availability. HardiePlank

lap siding comes in 12 ft. lengths.

Nominal widths from 5¼ in. to 12 in. create a range of exposures from 4 in. to 10¾ in.

HardiePlank lap siding is also available with ColorPlus

Technology as one of James Hardie’s preﬁnished products.

ColorPlus Technology is a factory applied, oven-baked ﬁnish available on a variety of James Hardie siding and trim

products. See your local dealer for details and availability of products, colors and accessories.

Select Cedarmill

Smooth

Beaded Smooth Custom Colonial Roughsawn

Beaded Cedarmill

Custom Colonial Smooth

Summary of content (11 pages)

PAGE 1
General Product Information General Installation Requirements HardiePlank lap siding is also available with ColorPlus® Technology as one of James Hardie’s prefinished products. ColorPlus Technology is a factory applied, oven-baked finish available on a variety of James Hardie siding and trim products. See your local dealer for details and availability of products, colors and accessories.
PAGE 2
General Product Information Working Safely Installation of HardiePlank® Lap Siding INSTALL A STARTER STRIP The bottom of the starter strip should be installed even with the bottom of the mudsill or the bottom edge of the sheathing. The strip must be installed over the water-resistive barrier, but occasional gaps should be left in the starter strip to allow any accumulated moisture behind the siding to drain away safely.
PAGE 3
General Product Information Working Safely INSTALLING THE PLANKS 10.3 Tools for Cutting and Fastening The first course of HardiePlank® siding is critical to the proper installation of the plank on the rest of the building. The first course should start at the lowest point of the house and within required clearances. Special attention should be made to ensure that it’s straight and level.
PAGE 4
General Product Information Working Safely Installation of HardiePlank® Lap Siding (cont.) BLIND NAILING (nailing through top of plank) ESR-1844 & 2290 Report Appendix/ Glossary HardiePanel® Vertical Siding HardieShingle® Siding HardiePlank® Lap Siding HardieSoffit® Panels HardieTrim® HardieWrap® Boards/Battens Weather Barrier Finishing and Maintenance General Fastener Requirements General Installation Requirements Tools for Cutting and Fastening 10.
PAGE 5
General Product Information Working Safely JOINT FLASHING 10.9 Flashing behind to add an additional layer of protection from water infiltration A. Joint Flashing (James Hardie recommended) General Installation Requirements B. Caulking* (Caulking is not recommended for ColorPlus for aesthetic reasons as the Caulking and ColorPlus will weather differently. For the same reason, do not caulk nail heads on ColorPlus products.} General Fastener Requirements C. “H” jointer cover Extend flashing 1 in.
PAGE 6
General Product Information Working Safely Installation of HardiePlank® Lap Siding (cont.) CONTINUING THE INSTALLATION ESR-1844 & 2290 Report Appendix/ Glossary HardiePanel® Vertical Siding HardieShingle® Siding HardiePlank® Lap Siding HardieSoffit® Panels HardieTrim® HardieWrap® Boards/Battens Weather Barrier Finishing and Maintenance General Fastener Requirements General Installation Requirements Tools for Cutting and Fastening 10.
PAGE 7
General Product Information To cut planks for the gable: 10.13 4 Draw the angle, cut and 1. Tack up a small scrap piece of siding where the first gable course is going. 2. Hold a second small piece of siding against the eave or rake board. Tip for fast gable installation 3. Trace the angle onto the scrap. 10.14 piece on the overlap lines and mark the length. Angle Template Draw line here 2 Before installing, measure down the 11/4 in. overlap at the top of the board.
PAGE 8
HardiePlank Lap Siding ® EFFECTIVE DECEMBER 2019 IMPORTANT: FAILURE TO FOLLOW JAMES HARDIE WRITTEN INSTALLATION INSTRUCTIONS AND COMPLY WITH APPLICABLE BUILDING CODES MAY VIOLATE LOCAL LAWS, AFFECT BUILDING ENVELOPE PERFORMANCE AND MAY AFFECT WARRANTY COVERAGE. FAILURE TO COMPLY WITH ALL HEALTH AND SAFETY REGULATIONS WHEN CUTTING AND INSTALLING THIS PRODUCT MAY RESULT IN PERSONAL INJURY. BEFORE INSTALLATION, CONFIRM YOU ARE USING THE CORRECT HARDIEZONE® PRODUCT INSTRUCTIONS BY VISITING HARDIEZONE.
PAGE 9
HardiePlank® Lap Siding CLEARANCE AND FLASHING REQUIREMENTS Figure 3 Figure 4 Roof to Wall Figure 5 Horizontal Flashing Min. ¼ in. Do not caulk Min. 1 in. Deck to Wall Slabs, Path, Steps to Siding As required by IRC code min 4 in. x 4 in. Z-Flashing Figure 7 Figure 6 Kickout Flashing Figure 8 Min. 1 in. Figure 9 Ground to Siding Figure 10 Figure 11 Gutter to Siding Sheltered Areas Mortar/Masonry L-Flashing Z-Flashing Z-Flashing Z-Flashing Min. 1 in. Min. ¼ in. 6 in.
PAGE 10
HardiePlank® Lap Siding FASTENER REQUIREMENTS continued Stud Figure 15 24” O.C. max 24” O.C. max Stud Figure 16 Joint Flashing Minimum overlap for Both Face and Blind Nailing 1 1/4” min. Overlap Nail Line 3/4”-1” Blind Nail 1 1/4” min. Overlap min. 1 1/4 in. overlap Face Nail Water Resistive Barrier Water Resistive Barrier Laminate sheet to be removed immediately after installation of each course for ColorPlus® products. Pin-backed corners may be done for aesthetic purposes only.
PAGE 11
HardiePlank® Lap Siding COLORPLUS® TECHNOLOGY CAULKING, TOUCH-UP & LAMINATE • Care should be taken when handling and cutting James Hardie® ColorPlus® products. During installation use a wet soft cloth or soft brush to gently wipe off any residue or construction dust left on the product, then rinse with a garden hose. • Touch up nicks, scrapes and nail heads using the ColorPlus® Technology touch-up applicator. Touch-up should be used sparingly.