Use and Care Manual

ManualsBrandsJameson ManualsElectrical600 ft. Traceable Rodder

7/16” OD Rod

Since 1956

OPERATION AND SAFETY MANUAL

Trace Underground Pipe Without Digging

- Less Disruption To Roads And Landscapes

- Minimal Pavement Breakage, Excavation, Restoration

Connect a signal transmitter to the Duct Hunter™ to energize unit

with a specic frequency. When rod is pushed into underground

pipe, signal radiates outward where a receiver detects frequen-

cy, allowing utility pipe to be traced from above ground.

• Trace to depths up to 10’

• Locate sewer laterals to conrm no cross bore has occurred

• Locate ductile iron, plastic, tile or concrete pipe

• Rod marked in 5’ increments

• 9” Bend radius

Jacket Core Wire

Warranty

Jameson products carry a warranty against any defect in material and workmanship for a period of one year from date

of shipment unless failure is due to misuse or improper application. Jameson shall in no event be responsible or liable for

modications, alterations, misapplications or repairs made to its products by purchaser or others. This warranty is limited

to repair or replacement of the product and does not include reimbursement for shipping or other expenses incurred.

Jameson disclaims any other express or implied warranty.

Duct Hunter

Rod

Diameter

Rod

Length

Recommended

Conduit Size

13-716-400M 7/16” 400’ 4” or Larger

13-716-500M 7/16” 500’ 4” or Larger

13-716-600M 7/16” 600’ 4” or Larger

13-716-800M 7/16” 800’ 4” or Larger

13-716-1000M 7/16” 1000’ 4” or Larger

• Wear safety glasses and gloves.

• Keep rod inside reel when not in use. Out-of-control rod can harm personnel or property.

• Keep rod clean. Some contaminants (including water) can conduct electricity.

• Keep secure footing. Protect yourself from falling should pulling eye move suddenly or separate from rod.

• Check for rod damage prior to use. Cracks, gouges, nicks, or white stress marks on jacket or sharp bends will weaken rod.

Injury could result if rod breaks while pulling.

• Do not use slip joint pliers, locking pliers or powered pulling equipment on rod.

• Do not force a pull that is stuck. Check for kinks or obstructions.

• Avoid pulling rod over sharp edges.

• Do not bend rod beyond 9” radius.

Do not use on live circuits. Electric shock may result. The Duct Hunter is equipped with a metal tip and

continuous internal copper wire. Do not use on or near live circuits. Electric shock may occur.

WARNING - ADHESIVE

Read manufacturer’s instructions before using adhesive. In case of eye contact, ush with water and seek medical atten-

tion If skin contact occurs, apply solvent (such as nail polish remover) to area and gently remove adhesive. Wash solvent

off with water. Solvents should not be used in case of contact with eyes or open wounds.

Always wear safety goggles (ANSI Std. Z87.1) and gloves when working with adhesive and/or unprotected berglass rod.

See adhesive product label for Safety Data Sheet (SDS).

Rod Is Marked In 5’ Increments

Add “MM” To Part Number For Metric Marked Rod

Add AWK To Part Number For All-Terrain Wheels

Summary of content (4 pages)

PAGE 1
OPERATION AND SAFETY MANUAL Since 1956 Trace Underground Pipe Without Digging - Less Disruption To Roads And Landscapes - Minimal Pavement Breakage, Excavation, Restoration Connect a signal transmitter to the Duct Hunter™ to energize unit with a specific frequency. When rod is pushed into underground pipe, signal radiates outward where a receiver detects frequency, allowing utility pipe to be traced from above ground.
PAGE 2
Accessories Part Number Accessories - Available Separately 13-716-AK Accessory Kit Roller Guide, End Ferrule, Splice Ferrule, 2 Adhesive, 2 Emery Cloth, Canvas Pouch 9-141 Roller Guide Guides rod through bends, sweeps, misalignments and wires; Increases contact with pipe on lead end of rod to improve overall signal strength 9-171 Roller Guide with Spring Adapter Heavy duty spring permanently attached to swivel roller guide helps push rod past difficult bends or debris in pipe 9-139 Swivel Eye
PAGE 3
Duct Hunter Operation 1. Operates in upright or horizontal position. If used in horizontal position, safety roller guides and brake control handle should be on top side. 2. Set drag brake to highest amount of drag (Fig. 1). 3. Insert end of fiberglass rod between the upper and lower nylon safety roller guides (Fig. 2). This ensures duct rod will be safely contained while working with it. 4. Release pressure on drag brake handle so rod will begin to slowly payout from reel. 5.
PAGE 4
Splicing Rod or Attaching New End Ferrule WARNING - ADHESIVE Read manufacturer’s instructions before using adhesive. In case of eye contact, flush with water and seek medical attention If skin contact occurs, apply solvent (such as nail polish remover) to area and gently remove adhesive. Wash solvent off with water. Solvents should not be used in case of contact with eyes or open wounds. Always wear safety goggles (ANSI Std. Z87.1) and gloves when working with adhesive and/or unprotected fiberglass rod.