Use and Care Manual

ManualsBrandsJameson ManualsElectrical100 ft. Fiberglass Fish Tape

The Wee Buddy® berglass sh tape features a highly visible, non-conductive berglass sh

tape with a protective polymer jacket (1/8” total outside diameter). This lightweight and

compact unit is ideal for all general conduit shing.

Warranty

Jameson products carry a warranty against any defect in material and workmanship for a pe-

riod of one year from date of shipment unless failure is due to misuse or improper application.

Jameson shall in no event be responsible or liable for modications, alterations, misapplications

or repairs made to its products by purchaser or others. This warranty is limited to repair or re-

placement of the product and does not include reimbursement for shipping or other expenses

incurred. Jameson disclaims any other express or implied warranty.

WB_MO5

WWW.JAMESONLLC.COM

Clover, SC

• DO NOT USE ON LIVE CIRCUITS. DISCONNECT POWER. Metal tip on rod.

• Wear safety glasses and gloves.

• Keep rod inside reel when not in use. Out-of-control rod can harm personnel or property.

• Keep rod clean. Some contaminants (including water) can conduct electricity.

• Keep secure footing. Protect yourself from falling should pulling eye move suddenly or

separate from rod.

• Check for rod damage prior to use. Cracks, gouges, nicks, or white stress marks on jacket

or sharp bends will weaken rod. Injury could result if rod breaks while being pulled.

• Do not use slip joint pliers, locking pliers or powered pulling equipment on rod.

• Do not force a pull that is stuck. Remove wires and check for kinks or obstructions.

• Avoid pulling rod over sharp edges.

• Do not bend rod beyond 1.5” radius.

WARNING - ADHESIVE

Read manufacturer’s instructions before using adhesive. In case of eye contact, ush with

water and seek medical attention If skin contact occurs, apply solvent (such as nail polish

remover) to area and gently remove adhesive. Wash solvent off with water. Solvents should

not be used in case of contact with eyes or open wounds.

Always wear safety goggles (ANSI Std. Z87.1) and gloves when working with adhesive and/or

unprotected berglass rod. See adhesive product label for MSDS.

Wee Buddy® With Accessory Kit

Wee Buddy® Without Accessory Kit

OPERATION AND SAFETY MANUAL

Summary of content (4 pages)

PAGE 1
OPERATION AND SAFETY MANUAL Wee Buddy® With Accessory Kit Wee Buddy® Without Accessory Kit The Wee Buddy® fiberglass fish tape features a highly visible, non-conductive fiberglass fish tape with a protective polymer jacket (1/8” total outside diameter). This lightweight and compact unit is ideal for all general conduit fishing. • DO NOT USE ON LIVE CIRCUITS. DISCONNECT POWER. Metal tip on rod. • Wear safety glasses and gloves. • Keep rod inside reel when not in use.
PAGE 2
Fishing Conduit With Wee Buddy® 1. Disconnect power 2. Identify both ends of conduit to be fished. Ensure switch gear or other components in area of vault or box will not be damaged by tape entering vault or box. 3. If conduit has existing wire, use flex tip on rod for pushing. 4. Insert rod into conduit. 6. Push rod through duct using short thrusts (approximately 6-8” long). This will take advantage of rod’s column strength and minimize danger of rod breakage.
PAGE 3
Manual de operación y seguridad Cinta buscadora de fibra de vidrio Wee Buddy® con el kit de accesorios Wee Buddy® sin el kit de accesorios La cinta buscadora Wee Buddy® de fibra de vidrio es un producto de alta visibilidad, que no es conductor eléctrico, con una funda protectora de polímero [diámetro externo de 3.175 mm (1/8”)]. Esta unidad liviana y compacta es ideal para buscar todo tipo de conductos. • NO USE LA CINTA EN CIRCUITOS CON CORRIENTE. DESCONECTE LA ELECTRICIDAD.
PAGE 4
Cómo usar el Wee Buddy® para buscar conductos 1. Desconecte la corriente 2. Identifique ambos cabos del conducto que desea buscar. Asegúrese de que los interruptores y demás componentes en la bóveda o caja no sufrirán daños cuando la cinta ingrese. 3. Si el conducto tiene un cable, use la punta flexible de la vara para empujarlo. 4. Inserte la vara en el conducto. 6. Inserte la vara en el conducto con empujones cortos (de unos 15 a 20 cm).