x HR-5 LINEAR PCM RECORDER www. jamminpro.
Contents Features/Overview.............................................................................................E2 Important Safety Notice....................................................................................E3 LCD Screen Description.....................................................................................E4 Panel Description ...............................................................................................E5 Connection……………………………………………………………..
Features - Built-In 2GBytes memory (Ready for more than 35 Hours stereo recording/music playback) - Expandable SDHC memory up to 32GBytes, (SD card not included) - Built-In 2 x dia. 9mm high sensitivity condenser microphone - 2 x 16mm Full ranger speakers built in - Large 1.9” LCD display with backlight - High speed USB2.0 for Mac and PC mass storage/card reader operation - 12 Hours lifetime on 2 x AA batteries (included) or external adaptor (not included) - 3.
Important Safety Notice Read this manual before use and keep it handy for future reference. Power requirements AC adaptor operation: - Be sure the use only an AC adaptor which supplies 5V DC and is equipped with a center-plus plug. The use of an adaptor other than the specificed type may damage the unit and pose a safety hazard - Connect the AC adaptor only to an AC outlet that supplies the rated voltage required by the adaptor Battery Operation : - Use to conventional AA size batteries.
LCD Screen Description A. Stereo/Mono mode indicator H. Repeat mode indicator B. Sample frequency indicator I. Message file name C. 24bit/16bit indicator E. Volume Level indicator J. Message folder name Built-in Memory SD card K. Message number F. Battery Level Indicator L. Record time indicator G. A-B Repeat indicator M. Schedule record indicator D. Button Lock indicator N. SPLIT / CUT indicator O P Q R O. Operation Status Record Pause Play P. Record Level Q.
Panel Description 1. Built-In Microphone (Left) 14. LCD Display 2. 3.5mm Stereo Earphone Jack 15. Next Track 3. Line-In Jack 16. Record / Stop 4. USB port 17. Play / Stop 5. Record indicator 18. Repeat / Folder 6. Left Channel Peak Indicator 19. Volume + 7. Right Channel Peak Indicator 20. Built-In Microphone (Right) 8. Up button 21. SD /SDHC card socket 9. Mode button 22. External Mic socket 10. Previous track 23. REC level control 11. Erase/Pause 24. DC adaptor input 12.
Connection Make connection to other equipment such as microphone and audio components as shown below NOTES: - To use the built-in microphones, disconnect any equipment from the external [MIC] jack or [Line-IN] jack. If anything is connected to these jacks, the built-in microphones are deactivated - If equipment is connected both to the external [MIC] jack and [Line-IN] jack, the[Line-IN] has the priority.
Battery Installation Replacing new batteries will not lose the files stored in the HR-5. If HR-5 is switched OFF with normal operation, it will keep the Date / Time and preference setting as previous setting 1. Push to open the battery cover. 2. Insert 2 x AA size batteries with correct polarity indicated. 3. Close the battery cover BATTERY INDICATIORS: * The batteries are fresh. * The batteries are exhausted, and need to be charged up or replaced.
Installing SD card and Basic Operation Inserting and removing the Card Open the SD card door, push the card fully until it clicks. Being careful about the direction you insert it. Close the Card door . If the card door cannot be completely closed, remove the card ,check its direction and then insert it again. To turn on/off the unit Press and hold the PLAY/STOP key more than two seconds, and the red indicator will flash, then enter into the default status --- voice mode.
Select / Switch File Folder MIC selection/Hold There are four memory storage areas(file folders) labeled A,B,C,D in the unit for your choice , it can store 99 files in each file folder , so it can store 396 in all . Absolutely ,it must be subject to its memory capacity . Select a file folder At recorder mode, press the “A-B” key to switch file folder . * The Factory setting is “A” . As the right picture , it shows the file folder name on LCD .
Recording a File Before recording , you can enable the VOX function (Voice Activate Recroding) for automatic record. You can go to « VOX setting » in the recording menu and select you desire VOX level. When record button is pressed and the input signal from Microphone/Line-In reaches the VOX level, recording will start automatically. Preparing for recording At recorder mode ,you may select a desired file folder by "A-B¨ key , and if VOX is enabled, VOX will appear on LCD.
Playback and Repeat Playing back a file Select a Folder by pressing REPEAT/FOLDER button and select a file. File name / Duration ./ Location will be shown on the LCD as right picture. Then press PLAY/STOP key to play it . you may press ERASE/PAUSE key for a pause , press PLAY/STOP key to stop it ,then press or key to go to the previous or next file, Press “+ / -” to adjust speaker volume while “0” is minimum volume , “31” is maximum volume.
Delete File and Recorder Setting Delete a file Select a desired file , and press ERASE/PAUSE key once, and select “ YES ” for deleting the file or “ NO ”to cancel by pressing or key , then press PLAY/STOP key to confirm to delete it. * For the Deletion of all files within a file folder refer to following section . Recorder setting At recorder mode, press Mode key to display the Recorder setting ,and select a setting key to enter into branch setting item by or key ,and then press PLAY/STOP or menu .
Recorder setting and Main menu 7. Edit Function : Set the Split or Cut function ,”split ” or “cut” will be shown on LCD. Split :While playing a file, press A-B key to select the split point. Then the message will be splited into two sections by the Split point ,and the second section is moved to the end of this file folder . Cut : While playing a file, press A-B key once to select point A icon will be displayed on LCD , press the 2nd A-B key again to select B.
Music Setting and System Setting 4. Genre : All files are sorted by genre in MP3’s ID3 info 5. Dir List : All downloaded music files show here. (except the recording file) 6. Record : All recording files show here . 7. Medialib Update : Refresh music files list . 8. Play Set : PlayMode ,Repeat One、All Repeat、Intro Play、order (Play Normally ) ; EQ select : You can select up to 7 preset EQ for MP3 music playback : <1> No effect ; <2>Pop Music ;<3> Rock ; <4> Dance ; <5> Jazz ; <6> Classic ;<7> Speech .
System Setting and connecting to PC 6. Device Information: It shows the all the HR-5 product information. 7. Recover System : Restore the unti to Factory setting. 8. Format U Disk : Format the internal memory of the HR-5 and all recording will be lost. . Notes: Please install or Backup the software – Magix Audio Cleaning Lab SE before you format the HR-5. IMPORTANT NOTES: · Once message(s) is deleted or the unit is formated, they can not be recovered.
Specification * Specifications are subject to change without notice. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Installing Magix Audio Cleaning Lab SE 1. Connect HR-5 to PC via the included USB cable 2. HR-5 will appear as a drive in your PC ( 2 Drives will appear as the 1st driver is for the internal memory and the 2nd driver is for the SD card memory) 3. Select the drive for the internal memeory and click folder [Magix Audio Cleaning Lab SE] 4. Double Click the start.exe 5. Click the “Install” on the top left corner 6. Select you language 7.
8. Select Installation Type and click “Next” to continue 9. Click “Next” to confirm the installation folder and tick the box if you want to creat shortcut on Desktop, then press “Next” to continue 10. Untick the box if you don’t want to register online and click “Next” to continue and 11. Installation start and it may takes couple minutes to finish, 12. Double click the Magix Audio Cleaning Lab SE icon to run the software.
