Instructions / Assembly

Page 13
Stealth
™
Series Pumps Installation and Operation Manual
5. Hand-tighten the lid to make an air tight seal. Do
not use any tools to tighten the lid, hand-tighten
only. Make sure all valves are open and the unions
are tight.
6. Turn on the power to the pump. Then turn on
the pump.
7. Once all the air has left the filter, close the
pressure release valve.
8. The pump should prime. The time it takes to
prime will depend on the elevation and length of
pipe used on the suction supply pipe. See Section
3.1.3.3 for proper elevation and pipe size.
9. If the pump does not prime and all the instructions
to this point have been followed, check for a
suction leak and then repeat Steps 2 through 7.
Section 5. Service and Maintenance
5.1 Routine Maintenance
Inspect the pump basket for debris by looking
through the clear pump lid. Remove any debris, because
as debris accumulates, it will begin to block the flow
of water through the pump. Keep the basket clean to
improve the performance of the pump.
1. Turn off the power to the pump. If the pump is
located below the water level, close the isolation
valves on the suction and discharge sides of the
pump to prevent a backflow of water.
2. Turn the lid's locking ring counter-clockwise until
'START' aligns with the ports. (You may use a tool
for leverage to open the lid, but never to tighten
the lid when closing it.) Carefully remove the lid.
CAUTION
A misaligned basket will cause the lid to be improp-
erly seated, allowing an air leak which could result
in pump damage.
3. Lift the basket out of the pump.
4. Dispose of the debris and thoroughly clean the
basket, making sure all the holes are open. Using
a garden hose, spray the basket from the outside to
help clear the holes. Use your hands to remove any
remaining debris.
5. Replace the basket in the pump by aligning the
opening with the suction pipe. If aligned properly,
the basket will drop easily into place. Do not force
into place.
6. Prior to replacing the lid, check for debris around
the lid o-ring seat, as this will cause air to leak into
the system. Clean the lid o-ring and place it on
the lid.
7. Hand-tighten the lid to make an air tight seal. Do
not use any tools to tighten the lid: hand-tighten
only.
8. Verify that all valves have been returned to the
proper position for normal operation.
9. Open the pressure release valve on the filter, and
make sure it is clean and ready for operation.
10. Turn on the power to the pump. Once all the
air has been evacuated from the filter, close the
pressure release valve.
5.2 Winterizing the Pump
CAUTION
The pump must be protected when freezing
temperatures are expected. Allowing the pump to
freeze will cause severe damage and void the war-
ranty.
CAUTION
Do not use antifreeze solutions in the pool,
spa, or hot tub systems! Antifreeze is highly toxic
and may damage the circulation system. The only
exception to this is Propylene Glycol. For more
information see your local pool/spa supply store or
contact a qualifi ed swimming pool service company.
1. Drain all water from the pump, system equipment,
and piping.
2. Remove the two drain plugs. Store the drain plugs
in a safe location and reinstall them when the cold
weather season is over. Do not lose the o-rings.
(Drain Plug with O-ring Set, R0446000)
3. Keep the motor covered and dry.
NOTE Covering the pump with plastic will create
condensation, and this moisture will damage
the pump. The best way to protect your pump
is to have a qualified service technician or
electrician properly disconnect the electrical
wiring at the switch or junction box. Once the
power is removed, the two unions can be
loosened and the pump stored indoors. For
safety, and to prevent entry of contaminants,
reinstall all conduit and terminal box covers.
4. When the system is reopened for operation, make
sure all piping, valves, wiring, and equipment
are in accordance with the manufacturer's
recommendations. Pay close attention to the filter
and electrical connections.
5. The pump must be primed prior to starting; refer
to Section 4.1, Start-up.