Operation Manual

ManualsBrandsjawbone ManualsMiscellaneousUp2

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2

https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 1/7

JAWBONESUPPORT>SETUP UP2

Setup UP2

Step 1: Charge your band*

1. Your band takes approximately one hour to fully

charge. Connect the charging cable to your band by aligning the pins on the

charger with the band. A magnet will hold the charger in place.

2. Insert the charging cable into the USB drive on

your computer or a standard USB wall adapter.

3. Icons on the face of the band will light up and

pulse while the band is charging.

Summary of content (7 pages)

PAGE 1
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 JAWBONE SUPPORT > SETUP UP2 Setup UP2 Step 1: Charge your band* 1. Your band takes approximately one hour to fully charge. Connect the charging cable to your band by aligning the pins on the charger with the band. A magnet will hold the charger in place. 2. Insert the charging cable into the USB drive on your computer or a standard USB wall adapter. 3.
PAGE 2
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 4. When the band is fully charged the icons will stop pulsing and the runner icon will glow solid. * Band shown is an UP3. Step 2: Size it for your wrist* 1. The band should be worn on your non-dominant wrist. Place the band on your wrist and rest your wrist on a flat surface. 2. Thread the strap through the loop and tighten the strap so that all of the sensors are touching your skin. The band should be snug, but not tight.
PAGE 3
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 3. Use your finger to hold the loop in place and fold the strap over. Note where the clasp lands. 4. Remove the band and adjust the buckle by sliding it in place. 5. Put the band back on and insert the clasp into the buckle. *Band shown is an UP3. Step 3: Check your band's mode to get started* https://help.jawbone.
PAGE 4
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 1. You must be wearing your band to activate it and change modes. 2. Rapidly tap the top band surface until it wakes. 3. The runner icon will glow to indicate you are in Awake mode. 4. A moon icon will glow to indicate you are in Sleep mode. https://help.jawbone.
PAGE 5
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 5. Touch and hold the surface of the band to switch modes, the band will vibrate and the runner or moon icon, depending on which mode you are in, will light up. 6. Set your band to Awake mode to track your daytime activity and steps. *Band shown is an UP3. Step 4: Get the UP App https://help.jawbone.
PAGE 6
/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 CONTACT SUPPORT 1-800-JAWBONE / 1-800-529-2663 Contact us Monday - Sunday, 6AM-7PM (Pacific) Jawbone Customer Service is closed in observance of all major US Holidays Company Shop About us Store News & Press Refurbished Products Careers Retail Partners Blog Corporate Sales Support https://help.jawbone.
PAGE 7
6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 Support Contact us Get the latest news Enter email address © 2014 Jawbone. All rights reserved. See our terms of use . https://help.jawbone.