Safety Instructions

Fields of Application
Specifications
SAFETY NOTE
1. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by
children without supervision.
4. If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6. The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or
less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10. Do not allow children to play with fixed controls. Keep
remote controls away from children.
11. Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until
the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14. Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation.
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
M
P2
Lithium Cell
3V
P2
UP
P2
STOP
DOWN
P1 button
Micro-USB Port
Charging Indicator
1. Do not expose motor to humid or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Charging Instructions
This motor has a 8V built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, motor will stop running when the voltage is lower than 6.5V and it will resume again when
the voltage is higher than 7.0V.
When the battery voltage is lower than 7.0V, the motor will alarm when the motor is running continuously,
the buzzer will beep 10 times, and Red LED will flash 10 times
Micro-USB charging: 5V
Micro-USB Port
Rechargeable Battery
Description Of LED
* For reference only.
Following data for reference
Model
DM20LEU/S-0.5/28
Rated Torque
(N.m)
0.5
Rated Speed
(rpm)
28
Working Voltage: DC 7.0V~8.4V
Working temperature (charging): 0℃ ~ +45℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency:
433.92MHz
Working temperature (discharge): 0℃ ~ +50℃
Maximum Running Time: 6 minutes
Red LED
Green LED
When the battery voltage is higher than 8.2V, green LED is always ON
When the battery voltage is less than 8.2V, the green LED will flash for 0.5s
When the battery voltage is less than 7.0V, the motor will alarm when the motor
run continuously, the buzzer will beep 10 times and red LED will flash 10 times
Press P1 shortly, if red LED flashes twice, the motor is in the deep sleep status
The motor is suitable for motorized roller blinds.
Built-in Receiver
Jog & Tilt
Adjust Limits
DC Power Supply
Reset to Factory Mode
Switch Direction
Stall Protection
Program Button
Built-in Lithium Battery
Electronic Limit
Preferred Stop Position
Speed Regulation
Radio Lock
* If the STOP button is not pressed within 10S, the motor will automatically exit the paring mode.
1 Pairing
Factory mode
P1
→
STOP
Press P1 button for 2S (1 jog), release button and beep once, or
re-power (1 jog and 1 beep), within 10 seconds, press STOP for
2S (2 jogs and 3 beeps), the motor has been paired successfully.
-3-
Please read following points of attention carefully before setting.
Setting Notice
Important Safety Instructions To Be Read Prior To Operation.
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
1. Don’t operate motors when low voltage alarm.
When the motor stops, when voltage is lower than 6.8V, it is prohibited to start, and can only start again
when the voltage is higher than 7.0V.
When the motor is running, when voltage is lower than 6.5V, the motor stops, and can only start again
when the voltage is greater than 7.0V.
When voltage is lower than 7.0V, the motor will alarm when the motor is running continuously, the buzzer
will beep 10 times, and Red LED will flash 10 times.
When voltage is lower than 6.0V, the motor stops beeping, and starts again when the voltage is higher
than 6.1V.
2. Operating：
①The valid interval of the emitter button is 10S, the emitter will quit the set after 10S.
②The motor will jog and flash for hint, please do the next step after the hint.
3. Set the limit position：
①After the upper / lower limit setting, and the upper / lower limit positin can’t at the same position.
②After the limit setting, with power off and memory function.
③Limit delete will clear all limit memory.
④It will exit limit setting when program there is no operation for 2 minutes.
4. If the emitter lost, please set up again with the new emitter.
5. One motor can store maximum 10 channels; after fully stored, if pair new channels, only the last one
will be covered circularly.
Button Instructions
-1- -2-
Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Functions of P1 button
1. Cycle Operation: Press P1 button once and every press the motor will run upward → stop → downward → stop,
cycle in turn.
2. Pairing or Pair/Unpair Additional Emitter: Press and hold P1 button for 2S, the motor will jog once, release button
and beep once, motor is ready for pairing or pair/unpair additional emitter.
3. Radio Lock: Press and hold P1 button for 6S, the motor will jog twice, release button and beep twice, the motor
enters radio lock status, the motor won't receive any signal; press P1 button once to disable Radio Lock.
4. Switch Direction: Press and hold P1 button for 10S, the motor will jog 3 times, release button and beep 3 times,
the running direction of the motor has been changed.
5. Reset to Factory Mode: Press and hold P1 button for 14S, the motor will jog 4 times, release button and beep
4 times, the motor has been reset to factory mode. At this point the motor will go into deep sleep. After entering
deep sleep, the motor can't be controlled. At this time, you need to press P1 button for 2S and then the motor
jogs to prompt to exit deep sleep; Red LED of limit head will flash twice if Short press P1 button after the motor
is in the sleeping status.
P1
Features
During operation,
if the red LED flashes,
pls charge the battery
When the battery
is charging, the
green LED flashes
If the LED is always
green, the battery has
been fully charged
Caution