HULALA H O M E ITEM NO.SBHM0888 NOTE: This brochure contains IMPORTANT safty info. Please read and keep for future reference.
MAINTAINANCE AND WARNING 1.Keep furniture away from heat sources. 2.Do not clean furniture with harsh cleaner or polishes.Do not use detergents,solvents,abrasives,spray packs or leather cleaner. Use non-color mild soa with warm water to clean spills(Mix 1:10 soap to water). 3.Do not place furniture under direct sunlight,material will possibly fade over time. 4.Do not use on site dry cleaning machine.Children should not climb or jump on the furniture. 5.
EXPLOSIVE VIEW 2PERSONEN 03/28
PARTS LIST x1 x1 x1 x1 x1 x1 x1 x2 x1 x2 x2 x2 x2 x2 x2 x2 04/28
PARTS LIST x4 x1 x1 x1 x1 05/28
HARDWARE LIST x32 x12 x8 x2 Ø5/32*1'' Ø3*14mm*7 x9 Ø8mm*2'' x8 x4 x5 x8 Ø3mm*15 Ø41''*1-1/4'' x2 x4 x4 x56 x16 Ø8mm*1'' x6 Ø8*30mm x4 Ø3*16 Ø3.
ASSEMBLY INSTRUCTIONS STEP-1 1.Use screw# 1 to attach magnetic catch #4 to the corresponding hole of panel(G), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-2 1.Insert part (G) into part (E),as picture show.
ASSEMBLY INSTRUCTIONS STEP-3 Use screw #8 to attach the legs (Q&R) to bottom panel B, tighten screws with Allen key #17.
ASSEMBLY INSTRUCTIONS STEP-4 1.Insert side panel (C&D) into the corresponding hole of preassembled step 2，make sure all holes aligned and use allen key #17 to tighten it as picture show.
ASSEMBLY INSTRUCTIONS STEP-5 1.Insert bottom panel (B) into the corresponding hole of preassembled step 4，make sure all holes aligned and use allen key #9 to tighten it as picture show.
ASSEMBLY INSTRUCTIONS STEP-6 1.Insert top panel(A) into the corresponding hole of preassembled step 5.make sure all holes aligned and use allen key#17 to tighten it as picture show.
ASSEMBLY INSTRUCTIONS STEP-7 1.insert back panel(F) into the groove of preassembled step 6,make sure all holes aligned and use screw#1 to attach them ，tighten screw #1 with screwdriver#18.
ASSEMBLY INSTRUCTIONS STEP-8 1.Connect part (M&L) to part N using screw #6 and tighten it with screwdriver #18 .Slide in the part (P) into the groove in part (L&M). make sure they are also in groove in part (N).
ASSEMBLY INSTRUCTIONS STEP-9 1.Connect part (M&L) to part O using screw #6 and tighten it with screwdriver #18. 2.Use screw# 5 to attach handle #3 to the corresponding hole of panel(O), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-10 1.Place the drawer to the rail.
ASSEMBLY INSTRUCTIONS STEP-11 1.Use screw #7 to attach wine glass holder (S&T&U) to the corresponding hole of panel(I), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-12 1.Insert shelf holder #2 into the corresponding hole of panel (C)&(D)&(E) and then attach panel (H&I) to it.
ASSEMBLY INSTRUCTIONS STEP-13 1.Use screw #11 to attach hinge #10 to the corresponding hole of panel(J&K), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-14 1.Move door (K) to corresponding position of side panel (E)&(D)，make sure all holes aligned and use screw #11 to attach them,tighten screw#11 with screwdriver#18.
ASSEMBLY INSTRUCTIONS STEP-15 1.Move door (J) to corresponding position of side panel (E)&(C)，make sure all holes aligned and use screw #11 to attach them,tighten screw#11 with screwdriver#18.
ASSEMBLY INSTRUCTIONS STEP-16 1.Use screw# 5 to attach handle #3 to the corresponding hole of panel(K), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-17 1.Use screw# 5 to attach handle #3 to the corresponding hole of panel(J), tighten screw with screwdriver #18.
ASSEMBLY INSTRUCTIONS STEP-18 Attention: Before the next step, adjust the feet of the locker to keep it level.
ASSEMBLY INSTRUCTIONS #16 x4 #9 x2 x1 #18 Ø3*16 STEP-19 1.Use screw #16 to attach part #9 to preassemble unit at step 15 .
ASSEMBLY INSTRUCTIONS #13 #9 x4 x2 #14 x4 #18 x1 STEP-28 1.Install the anti-collapse device. 2.Mark the position on the wall, that corresponds to the location of part#9 on the of panel (A); Drill and insert the expandable screw #13 by hammer. 3.Assemble the part #9 to the wall. Align the hole in the part #9 with the expandable screw #13, use screw #14 to attach it and tighten by screwdriver#18. NOT PROVIDED L L A W L L 1. A W #9 #14x4 2. ALL W #13x4 3.
ASSEMBLY INSTRUCTIONS #15 x2 STEP-21 1.Let the plastic belt #15 pass through the both part #9 and pull tightly. 2. #9 L L A #15x2 W 1.
WARRANTY 1.We strive to offer high-quality products,and we also try our best to satisfy each and every customer that orders from us with product or service as needed. 2.We provide 30 days warranty starting from the time you receive the item.Each customer must provide a record of their order such as the order number,or item receipt for any items that are out of the warranty period you may also still receive. 3.Replacement parts by purchasing them with our company if they are available.
