Owner manual

ManualsBrandsJaypro Sports ManualsSports and recreationBLCH-TMKIT

Rev -, 4/10 Page 1 of 7

---

BLCH-TOW4515 & BLCH-TOW4521

---

(

TRANSPORT KIT FOR 3, 4 OR 5 ROW

BLEACHER FROM 15 FT TO 21 FT

)

Installation Instructions

BLCH-TOW4515 → (For 15 FT long bleacher)

BLCH-TOW4521 → (For 21 FT long bleacher)

BLCH-TMKIT → (Mounting kit brackets with hardware)

Call Jaypro Sports Equipment at 1-800-243-0533

during regular business hours for technical support.

www.jaypro.com

Summary of content (7 pages)

PAGE 1
--- BLCH-TOW4515 & BLCH-TOW4521 --(TRANSPORT KIT FOR 3, 4 OR 5 ROW BLEACHER FROM 15 FT TO 21 FT) Installation Instructions BLCH-TOW4515 → (For 15 FT long bleacher) BLCH-TOW4521 → (For 21 FT long bleacher) BLCH-TMKIT → (Mounting kit brackets with hardware) Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.
PAGE 2
JAYPRO SPORTS 3, 4 & 5 ROW BLEACHER TOW KIT FOR 15’ & 21’ BLEACHER IMPORTANT NOTICE: 1. BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR MISSING HARDWARE IMMEDIATELY. 2. SECURELY TIGHTEN ALL NUTS AND BOLTS. 3. THIS TOW KIT IS NOT INTENDED FOR ROAD USE. DO NOT EXCEED 5 MPH. 4. NEVER ALLOW ANYONE TO RIDE ON BLEACHER DURING TRANSPORT. 5. USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE HAZARDOUS. 6.
PAGE 3
For 15 FT long bleacher For 21 FT long bleacher FIGURE: 1 Rev -, 4/10 Page 3 of 7
PAGE 4
Install Wheel Mounting Brackets and Receiver: 1) Install two mounting brackets (5) on both ends of the bleacher leg selected to hold the wheels (see figure 1). Locate where the brackets will be mounted to the lower frame member as shown, avoiding any interference with vertical or diagonal support members. The spacing between brackets should not exceed 18”. 2) Using a 7/16” transfer punch, locate and drill two 7/16” holes, exactly 2” apart, for each bracket.
PAGE 5
Assemble Wheel Assembly: 1) Assemble the 4” wheel hub kit (13) and the tire wheel (11) using the lug nuts in the 4” wheel hub kit (13). Apply grease to the inside of the hub and the bearings. Determined the backside of the tire wheel and insert the bearing, washer, hub seal and 1.25” square BT8 spindle (12). On the front side of the tire wheel. Insert the bearing, washer, slotted hex nut and lock the 1.25” square BT8 spindle (12) with a cotter pin. Then apply the hubcap to finish the wheel assembly.
PAGE 6
Install Tow Tongue / Spreader Bar: 1) The mounting brackets for the tow tongue are to be installed on the first and second frame leg, from the tow end of the bleacher. The location of the brackets, side to side, needs to be determined. Since the bleacher has more weight towards the back rows, the location of the tongue needs to be shifted towards that side – not centered. On a 5-row bleacher, the tongue will be located to the right of the vertical support for the fourth row (see figure 5).
PAGE 7
FIGURE: 8 Rev -, 4/10 Page 7 of 7