P10Profile Operating instructions Version 1.05 Software >= 1.0.
P10 - 02 -
P10 Content 1. Introduction ���������������������������������������������������������������������������������������������������������������������������05 1.1 P10 Profile models ������������������������������������������������������������������������������������������������������������������������������05 1.2 Important differences between the models HP/HC/WW ����������������������������������������������������������������������05 2.
P10 - 04 -
P10 1. Introduction 1.1 P10 Profile models The P10 Profile is available in 3 models. The models differ in the light module and partly in the color filters and in the CTC filters. The differences can be found in the DMX channel functions. - P10 Profile HP (High Power) - P10 Profile HC (High CRI) - P10 Profile WW (Warm white) Specification Color temperature Luminosity CRI Correction filter HP - High Power HC - High CRI WW - Warm White 6800 K 5800 K 3200 K 25.000 lm (15.
P10 2. Dimensions 223,6 140 140 140 140 140 223,6 140 223,6 412 199 412 397 397 397 199 223,6 223,6 140 140 412 199 Farbe: Lichtanlagentechnik GmbH Sallersteig 15, 89134 Blaustein 398 Material: Farbe: Blechdicke: Farbe: Abmessung: Fax.: 07304 / 9617-99 Lichtanlagentechnik GmbH Oberfläche: Lichtanlagentechnik GmbH Name SallersteigDatum 15, 89134 Blaustein Sallersteig 15, 89134 Blaustein kuehngruen Erstellt Tel.: 07304 / 9617-0 Tel.:Blechdicke: 07304 / 9617-0 Allgemeintoleranzen Fax.
P10 3. Product overview Bottom cover Top cover Arm cover Handles LCD display Function keys Farbe: Lichtanlagentechnik GmbH Sallersteig 15, 89134 Blaustein Oberfläche: Material: Tel.: 07304 / 9617-0 Fax.: 07304 / 9617-99 Blechdicke: Abmessung: Datum Erstellt Name Head kuehngruen Allgemeintoleranzen ISO 2768-m Art.-Nr.
P10 4. Safety instructions ! ATTENTION: For your own safety, please read these operating instructions carefully before first use. This spotlight has left our company in excellent condition. To maintain this condition and to ensure safe operation, it is absolutely essential to observe the following safety instructions and warnings which are described in this operating manual.
P10 ! ATTENTION: This fixture corresponds to protection class I. For this reason, this spotlight must be connected to a mains socket with earthing contact. Never connect this device to a dimmer pack. During first use, some smoke and odour may occur. This is normal and does not necessarily mean that the device is defective. The device becomes hot during operation.
P10 ! ATTENTION: The distance between the light emission and the surface to be illuminated must be at least 2.0 metres. The maximum ambient temperature of 45°C must not be exceeded. ! ATTENTION: The front lens must be replaced if it is visibly damaged to the extent that its function is impaired, e.g. by cracks or deep scratches! Do not operate the device until you have become familiar with its functions. Prevent operation by persons who are not qualified to use the device.
P10 Connection outside Europe: The P10 Profile may only be operated on the following power supply systems: Mains P10 2 wires, 1 phase L N L N PE 3 wires, 1 phase L N L L L1 L2 L3 N L N 4 wires, 3 phases ! ATTENTION: In Canada, the P10 Profile may only be operated in a 2-wire, 1 phase network with a maximum voltage of 120V! N PE 5.3 Mains connection Connected loads: Voltage 100-240 V, frequency 50 - 60 Hz, power max.
P10 5.5 Signal connections 5.5.1 DMX cabling The DMX cabling (signal lines) should be done with a 4-pin cable with shielding. We recommend a DMX cable (110 Ohm, 2x0.22mm2 or 4x0.22mm2). The plugs and sockets are 5-pin XLR connectors, which can be purchased in specialist shops. Pin assignment: Pin1 = Ground/Shielding Pin2 = DMX Pin3 = DMX + Pin4 = not connected Pin5 = not connected 2 1 Cable with shielding 1 2 3 3 4 5 5 4 The P10 Profile has a DMX-in and DMX-out connector.
P10 5.6 Mounting the devices ! ATTENTION: Allow a fixture distance of at least 0.5 metres from easily flammable material and the distance between the light emission and the surface to be illuminated must be at least 2.0 meters. The P10 Profile can be placed on the floor or hang on a trussing system. Also a mounting horizontally to a truss system like in the picture is only allowed if the omega brackets are attached to the outer camlocks. (distance 223.
P10 6. Control panel The P10 Profile has a graphic colour touch display that can be rotated 180° when installed in a suspended position. The display can be rotated in the PERSONALITY MENU or via shortcut ENTER + UP in the main screen. All parameters of the P10 Profile can be set on the control panel (see menu overview page 14).
P10 DMX addressing In the main menu, the DMX address can be set directly by pressing the up/down keys. Display operation via battery backup By pressing the left button below the display, the configuration battery operation of the headlamp is activated, so the headlamp can be configured without power. It is possible to configure all the settings displayed by the menu, for example the DMX address can be set. 6.1 Menu overview P10 Profile grey - corresponds to the default setting ENTER FACTORY DEF.
P10 DISPLAY ORIENTA. STANDARD MAIN SCREEN MO STANDARD FLIP USER ID SAFE MODE SWIT OFF USER FIXTURE ID ID +/- LED FADE OUT STANDARD ON SOFT BLMODE RAW MOVE/ANGLE SERVICE RESET FIXTURE ERROR LIST SURE? LIST PAN TIMEOUT CLEAR SURE? FUNCTION TEST START TEST DMX TEST DMX CHANNEL INIT PAN/TILT SURE? DISPLAY CONTR. D.
P10 SPARKLE SPARKLE +/- SPARKLE SP SPARKLE SP +/- PRISM PRISM +/- PRISM ROT PRISM ROT +/- PRISM 2 PRISM 2 +/- PRISM ROT 2 PRISM ROT 2 +/- FROST FROST +/- FROST 2 FROST 2 +/- MACRO MACRO +/- SPEED P/T SPEED P/T +/- SPEED EFF SPEED EFF +/- MOVE B-OUT MOVE B-OUT +/- RUN TIMEBASE 1 SEC 1/10 SEC REMOTE INFO SOFTWARE VER. FIXTURE ID TOT OP. TIME TOT LAMP TIME TOT BAT CHARGE T.
P10 6.2 FACTORY DEFAULTS - Factory settings To reset P10 Profile to factory settings, go to the menu item FACTORY DEFAULTS, LOAD DEFAULTS. After confirming the security query SURE? by pressing the "ENTER" button for 2 seconds, all parameters are reset to the factory settings. 6.3 USER DEFAULTS - User settings If the user has set the P10 Profile in the PERSONALITY menu to their personal settings, these can be saved and loaded in the USER DEFAULTS menu.
P10 DMX OUTPUT CONFIG - configuration of the DMX output Under this menu item, the DMX output of the headlamp can be activated, that is a received Artnet, or wireless DMX signal can be output by activating this menu item -> ON via the DMX socket again. Make sure that there is no signal at the DMX input at the same time !! CURVES - setting dimmer, RGB/CMY, frost curve Dimmer curve: The dimmer curve can be changed from SQUARE to LINEAR and to SQUARE INV..
P10 PAN TILT SPEED - setting pan/tilt speed In the PAN TILT SPEED menu you can set the maximum speed, the acceleration and thus also the movement volume of the P10 Profile. The following setting options are available. WHISPER: The speed of Pan / Tilt is reduced so much that a volume of 29dB (A) is not exceeded. SILENT: The speed of Pan / Tilt is slightly faster and thus louder as compared to the Whisper setting.
P10 LED FADE OUT - type of dimming Used to set how to dim the lower range from 0-5%. STANDARD: When dimming the headlamp, all LED's dim out at the same time. SOFT: When the headlamp is dimmed, the LED's are dimmed out in groups (in a row) one row after the other. BLMODE - Type of shutter control Serves to switch the shutter control. With the RAW setting, the two motors of the individual apertures are controlled separately via DMX.
P10 Operation via master-slave function: Connect the P10 Profile via DMX lines and activate the REMOTE menu item for all slave devices. To do this, navigate in the STANDALONE menu to the REMOTE sub-menu. Activate the REMOTE function by pressing and holding “ENTER”, and also pressing “ESC”. The spotlight is in slave mode when the display shows the status REMOTE INACTIVE or REMOTE ACTIVE. REMOTE INACTIVE: The P10 Profile is in slave mode but does not receive a DMX signal.
P10 7. Control options 7.1 DMX 7.1.1 Operating modes P10 Profile The P10 Profile has 2 different DMX modes. The respective mode can be set in the PERSONALITY DMX MODE menu item. The set mode is displayed in the main menu.
P10 Channel 41 Colour wheel Channel 42 Cyan Channel 43 Fine cyan Channel 44 Magenta Channel 45 Fine magenta Channel 46 Yellow Channel 47 Fine yellow Channel 48 CTO Channel 49 CTO fine Channel 50 Sparkle Channel 51 Sparkle speed Channel 52 Prism 1 Channel 53 Prism 1 rotation Channel 54 Prism 1 fine rotation Channel 55 Frost 1 Channel 56 Frost 2 Channel 57 Effects macro Channel 58 Pan/tilt speed Channel 59 Effect speed Channel 60 Blackout Move - 24 -
P10 7.1.2 DMX channel functions P10 Profile M1 M2 1 1 M3 Function Pan (X) movement 546,74° 000-255 DMX 2 2 Pan (X) fine (16 Bit) 000-255 3 3 Tilt (Y) movement 281,16° 000-255 4 4 Tilt (Y) fine (16 Bit) 000-255 5 5 Control channel To enable uniform dimming manually via faders for all light mixing consoles, 5 different settings for the DMX smoothing are available.
P10 - 26 - DIMMER CURVE - selection of dimmer curve LINEAR - linear dimmer curve SQUARE - exponential dimmer curve SQUARE INVERSE - exponential inverse dimmer curve not used 136-136 137-137 138-138 139-139 RGB/CMY CURVE - selection of RGB/CMY curve SQUARE INVERSE LEGACY - Exponential inverse legacy RGB/CMY curve LINEAR - linear RGB/CMY curve adapted to P18 MK2 SQUARE INVERSE - Exponential inverse RGB/CMY curve adapted to P18 MK2 140-140 141-141 142-142 FROST CURVE - selection of frost curve LINEAR - l
P10 6 7 8 9 10 Shutter Shutter closed Shutter open Open pulsing shutter >20Hz (rapid - slow) Shutter open Fade effect with dimmer (slow - rapid) Shutter open Shutter closed Open pulsing shutter <20Hz (rapid - slow) Shutter open Close pulsing shutter >20Hz (rapid - slow) Shutter closed Shutter fade, 0% (rapid - slow) Shutter open Shutter fade, 100% (rapid - slow) Shutter closed Random shutter 100% (rapid - slow) Shutter open Random shutter 0% (rapid - slow) Shutter closed Random shutter fade, 0% (rapid-
P10 14 18 19 - 28 - Gobo 2 016-023 Gobo 3 024-031 Gobo 4 032-039 Gobo 5 040-047 Gobo 6 048-055 Gobo 7 056-127 Gobo 0 (open) Gobo 1 shake (fast - slow) Gobo 2 shake (fast - slow) Gobo 3 shake (fast - slow) Gobo 4 shake (fast - slow) Gobo 5 shake (fast - slow) Gobo 6 shake (fast - slow) Gobo 7 shake (fast - slow) Gobo wheel rotation (fast - slow) Gobo wheel rotation (fast - slow) 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-223 224-255 Gobo positioning/rotation 1 Gobo
P10 15 16 17 18 Gobo 4 032-039 Gobo 5 040-047 Gobo 6 048-055 Gobo 7 056-127 Gobo 0 (open) Gobo 1 shake (fast - slow) Gobo 2 shake (fast - slow) Gobo 3 shake (fast - slow) Gobo 4 shake (fast - slow) Gobo 5 shake (fast - slow) Gobo 6 shake (fast - slow) Gobo 7 shake (fast - slow) Gobo wheel rotation (fast - slow) Gobo wheel rotation (fast - slow) 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-223 224-255 Gobo positioning/rotation 2 Gobo positioning 0° - 540° Gobo rotation, r
P10 23 24 25 26 27 28 29 30 - 30 - 34 Aperture 3b fine (16 Bit) 000-255 35 Aperture 4a 0-100% 000-255 36 Aperture 4a fine (16 Bit) 000-255 37 Aperture 4b 0-100% 000-255 38 Aperture 4b fine (16 Bit) 000-255 39 Aperture rotation -65° / +65° 000-255 40 Aperture rotation fine (16 Bit) 000-255 41 Color wheel White (color shift gobo on) White (color shift gobo off) White/CTB CTB CTB/Red Red Red/Yellow Yellow Yellow/Magenta Magenta Magenta/Green Green Green/Orange Orange Orange/CRI C
P10 31 32 33 34 35 36 37 38 39 40 Sparkle - Glitter effect Sparkle effect inactive Sparkle effect intensity (minimum - maximum) 000-000 001-255 Sparkle speed Faded sparkle effect (slow -> rapid) Switched sparkle effect (slow -> rapid) Repetition of the fading and switching blocks 000-031 032-063 064-255 Prism 1 Open Prism 1 (5-fold linear) 000-007 008-255 Prism 1 positioning/rotation Prism positioning (0° - 540°) Prism rotation, right (rapid -> slow) Stop prism rotation Prism rotation, left
P10 7.1.3 Control channel Via the control channel different functions of the fixture can be switched. The following functions can be switched via the control channel.
P10 7.4 Wireless-DMX The P10 Profile is equipped with a Lumen Radio CRMX receiver for wireless DMX. The receiver can process both DMX and RDM. If there is a cable and wireless connection to the P10 Profile, the cable connection has priority! The received signal can be output via the DMX connection. To do this, set the DMX OUTPUT CONFIG setting to ON in the PERSONALITY menu. After confirming with ENTER, the spotlight will output the entire universe received via wireless DMX. 7.
P10 7.5.
P10 Pan Tilt Speed ✔ ✔ Effect Speed ✔ ✔ Backlight Mode ✔ ✔ Disp Orientation ✔ ✔ Main Screen Mode ✔ ✔ Safe Mode Switch ✔ ✔ LED Fade Out Mode ✔ ✔ Blade Mode ✔ ✔ GET SET Temp Sens Base LCD ✔ ✔ Temp Sens Base PS ✔ ✔ Temp Sens Head PCB ✔ ✔ Temp Sens Head Drv ✔ ✔ Temp Sens Head LED ✔ ✔ Temp Sens Head Air ✔ ✔ 6.5.5 RDM sensor IDs RDM sensor ID DISCOVERY Note RDM sensors 8. Service 8.
P10 FINE ADJUST The FINE ADJUST area is protected by a key combination. Focus, shapers, shaper rotation, pan and tilt are calibrated at the factory. If there are large deviations in the calibration between the individual headlights, this can be corrected in the FINE ADJUST menu. For more information please contact our service. IDENTIFY DEVICE The RDM command IDENTIFY DEVICE can be called up or deactivated via this menu item. 8.
P10 Usable diameter, rotating gobowheel 1: 15.00 mm Usable diameter, rotating gobowheel 2: 16.00mm Outer diameter: 19.90 mm (+0/-0.1 mm) Maximum thickness: 1.1 mm 15/16mm 19.9 mm 8.3 Gobo size If you want to have your own gobos produced, please note the following dimensions: 8.5 Software update The P10 Profile can be updated via a USB stick with micro-USB connection. To do this, copy the file directly into the root directory of the USB stick.
P10 8. Cleaning the device ! WARNING: Disconnect fixture before opening! You should check the function of the fans in the head and foot at regular intervals. Above all, you should make sure that the air inlets and the interior of the P10 Profile are free of fluff and dust. To do this, open the head cover (3x camlocks with half a turn) and the base plate on the foot. You can clean the P10 Profile with a brush and a vacuum cleaner.
P10 9.
P10 TSENS BPS ER Sensor Error Base Power Supply AC/DC TSENS BLCD ER Sensor Error Base LCD TSENS BAIR ER Sensor Erroe Base Air TSENS HMAIN ER Sensor Error Head Main PCB TSENS HDRV ER Sensor Error Head LED Driver PCB TSENS HLED ER Sensor Error Head LED TSENS HAIR ER Sensor Error Head Air (Ambient) HIGH TEMP BLCD High Temperature Base LCD PCB HIGH TEMP BAIR High Temperatur Base Air (SPARX ONLY) HIGH TEMP BPS High Temperature Base PSU AC/DC HIGH TEMP HMAIN High Temperature Head Main PCB HI
P10 10. Specifications Dimensions and weight Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 mm Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 mm Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 mm Net weight. . . . . . . . . . . . . . .
P10 11.
P10 - 43 -
JB-Lighting Lichtanlagentechnik GmbH Sallersteig 15 89134 Blaustein Tel. +49 7304 9617-0 Fax. +49 7304 9617-99 info@jb-lighting.de www.jb-lighting.
