PERFORMANCE AV1 DIGITAL SURROUND PROCESSOR/CONTROLLER USER GUIDE
IMPORTANT SAFETY INSTRUCTIONS 1. ing the cart/appartus combination to avoid injury from tip-over. Read these instructions. 2. 3. 4. 5. 6. 7. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic’” and the double-D symbol are trademarks of Dolby Laboratories. “Surround EX” is a jointly developed technology of THX and Dolby, Laboratories, Inc., and is a registered trademark of Dolby. Used under authorization. THX, Ultra and Ultra2 are trademarks of THX Ltd., which may be registered in some jurisdictions. All rights reserved.
Introduction JBL Performance DOCUMENTATION CONVENTIONS This document contains general safety, installation and operation instructions for the AV1 Digital Controller. It is important to read this user guide before attempting to use the product. Pay particular attention to safety instructions. The following symbols are used in the document: Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosureævoltage that may be sufficient to constitute a risk of shock.
Introduction AV1 ENGLISH IMPORTANT SAFETY INSTRUCTIONS DEUTSCH WICHTIGE SICHERHEITSHINWEISE 1 Save these instructions for later use. 1 Bewahren Sie diese Anleitungen zur späteren Benutzung auf. 2 Follow all instructions and warnings marked on the unit. 2 Befolgen Sie alle Anleitungen und alle Warnhinweise auf dem Gerät 3 Follow all instructions and warnings marked on the unit. 3 4 Always use with the correct line voltage.
Introduction JBL Performance ESPAÑOL INSTRUCCIONES DE SEGURIDAD IMPORTANTES 1 Guarde estas instrucciones para futuras referencias. 2 Siga todas las instrucciones y tenga en cuenta las advertencias que aparecen en la unidad y en las instrucciones de funcionamiento. 3 Utilice siempre la tensión de línea correcta. Consulte las instrucciones del fabricante, donde se especifican los requisitos de alimentación.
Introduction AV1 ITALIANO IMPORTANTI NORME DI SICUREZZA PORTUGUESE INSTRUÇÕES IMPORTANTES DE SEGURANÇA 1 Conservare le presenti norme per l’utilizzo futuro. 1 Guarde essas instruções para uso posterior. 2 Seguire sempre tutte le istruzioni e gli avvertimenti segnati sull’unità e nelle istruzioni operative. 2 Siga todas as instruções e fique atento aos avisos marcados na unidade e nas instruções de operação. 3 Utilizzare sempre la corretta tensione di alimentazione.
Introduction JBL Performance DANSK VIGTIG INFORMATION OM SIKKERHED SUOMI TÄRKEITÄ TURVALLISUUSOHJEITA 1 Gem denne vejledning til senere brug. 1 Säilytä nämä ohjeet tulevaa käyttöä varten. 2 Følg alle anvisninger og advarsler på apparatet. 2 Seuraa kaikkia yksikköön merkittyjä ohjeita ja varoituksia. 3 Apparatet skal altid tilsluttes den korrekte spænding. Der henvises til brugsanvisningen, der indeholder specifikationer for strømforsyning.
Introduction AV1 NORSK VIKTIG INFORMASJON OM SIKKERHET SVENSKA VIKTIGA SÄKERHETSFÖRESKRIFTER 1 Ta vare på denne veiledningen for senere bruk. 1 Spara dessa föreskrifter för framtida bruk. 2 Følg alle anvisningene og advarslene som er angitt på apparatet. 2 Följ alla anvisningar och varningar som anges på enheten. 3 Apparatet skal alltid anvendes med korrekt spenning. Produktbeskrivelsen inneholder spesifikasjoner for strømkrav.
Introduction Unpacking and Inspection After unpacking the unit, save all packing materials in case the unit ever needs to be shipped. Thoroughly inspect the modules and packing materials for signs of damage. Report any damage to the carrier at once; report equipment malfunction to the dealer. JBL Performance Contenu de L’emballage et Inspection Après avoir ouvert l’emballage, conservez-le pour tout retour. Inspectez avec soin les modules et les matériaux d’emballage pour tout signe de dommage.
Introduction AV1 Table of Contents Documentation Conventions........................................................ ii Important Safety Instructions........................................................ v Wichtige Sicherheitshinweise........................................................ v Instrucciones De Seguridad Importantes.......................................vi Instructions Importantes Relatives À La Sécurité............................vi Importanti Norme Di Sicurezza ..........................
Introduction Mode Adjust Mode Adjust..............................................................................5-2 Listening Mode Activation .........................................................5-2 Preferred Listening Mode Selection Parameters ............................................................................ 5-3 Mode And Buttons ....................................................... 5-3 Mode Family Selection Buttons ..............................................
1 Getting Started About the AV1............................................................................ 1-2 Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Product Registration ................................................................... 1-4 Installation Considerations.......................................................... 1-4 Remote Control Battery Installation ............................................
Getting Started JBL Performance ABOUT THE AV1 Thank you for purchasing the AV1 Digital Controller, an 8-channel audio and video control center. The AV1 includes eight configurable inputs, each of which can be assigned to its eight digital audio, eight analog audio, five composite video, five S-video or three component video input connectors. The analog connectors can be configured for up to two 5.1-channel sources. Inside and out, the AV1 is designed for possible future developments.
Getting Started AV1 Complementing its audio performance, the AV1 features two broadcast-quality video switchers. A wide-bandwidth component video switcher accepts analog component or RGB video signals, while a composite and S-video switcher accepts high-quality NTSC, PAL or SECAM video signals. The component video switcher can pass high-definition TV (HDTV) signals, as well as standard-defini- tion TV signals. Both switchers are designed to pass video signals without alteration or degradation.
Getting Started JBL Performance PRODUCT REGISTRATION Please register the AV1 Digital Controller within 15 days of purchase. Register online at www.JBL.com or complete and return the product registration card attached to the back cover of this user guide. Retain the sales receipt as proof of warranty coverage. INSTALLATION CONSIDERATIONS The AV1 requires special care during installation to ensure optimal performance.
AV1 Getting Started REMOTE CONTROL BATTERY INSTALLATION The remote control requires two AA batteries. The batteries should be replaced as needed. Alkaline batteries, which last longer without leaking, are recommended. When battery power is low, the remote control enters a low-voltage condition, preventing it from operating the AV1. When this occurs, replace the batteries. Normal operation will resume when new batteries are installed. To replace the remote control batteries: 1.
Getting Started 1-6 JBL Performance
2 Basic Operation Front-Panel Overview ................................................................ 2-2 Rear-Panel Overview .................................................................. 2-4 Remote Control Overview ......................................................... 2-6 Operation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Main Menu . . . .
Basic Operation JBL Performance FRONT-PANEL OVERVIEW The numbers in the front-panel illustration correspond with the numbered items below. 2 1 5 3 4 7 6 1 STANDBY BUTTON 2 FRONT-PANEL DISPLAY Use the Standby button to activate or deactivate standby mode. The Standby button performs no function when the AV1 is powered off with the rear panel power switch. Use the Front-Panel display to view the current input, listening mode, input source and volume level.
Basic Operation AV1 3 IR RECEIVER 5 MODE The IR Receiver receives infrared commands from the AV1 remote control. There are three associated LEDs. Use the Mode buttons to scroll to the previous and next available listening mode. Scrolling occurs in the order shown in the MODE ADJUST menu. Press the Mode button to scroll upward through available listening modes. Press the Mode button to scroll downward through available listening modes. See “Listening Mode Activation” on page 5-2 for more information.
Basic Operation JBL Performance REAR-PANEL OVERVIEW The numbers in the rear-panel illustration correspond with the numbered items below. 8 10 7 6 3 9 5 4 1 2 1 POWER SWITCH 3 DIGITAL AUDIO INPUT CONNECTORS (S/PDIF) Use the Power switch to power the AV1 on or off. The I and O positions represent "on" and "off" status respectively. When the AV1 is powered on, the front-panel Standby button or remote control On button can be used to activate and deactivate standby mode.
Basic Operation AV1 4 ANALOG AUDIO INPUT CONNECTORS Note: Provide analog audio input. Eight stereo analog audio input connectors labeled 1 to 8 are available. Connectors labeled 3, 4, 5, 6, 7 and 8 can be configured as 5.1-channel connectors. • Composite video output connectors are available when a composite source is present. • S-video output connectors are available when an S-video source is present.
Basic Operation JBL Performance REMOTE CONTROL OVERVIEW The AV1 remote control provides full operation of the AV1, including commands such as menu navigation that are not available from the front-panel. The command matrix that beginning on page 2-10 indicates the commands remote control buttons perform when each command bank is active. The numbered items in the matrix correspond with the remote control illustrations on pages 2-10 to 2-13.
Basic Operation AV1 MENU ITEM SELECTION Use the remote control Menu arrows to select menu items. Arrow Navigation Function(S) • When a menu is open, press the Menu arrow to select the highlighted menu item. • When all menus are closed, press the Menu arrow to open the MAIN MENU. • When a menu is open, press the Menu arrow to close the menu and, in most cases, open the previous menu. Subsequent presses continue to close the current menu and open the previous menu until the MAIN MENU is closed.
Basic Operation JBL Performance MENU PARAMETERS HORIZONTAL BAR GRAPHS Selecting a menu parameter opens a drop-down menu or horizontal bar graph that is used to select the desired setting. Selecting some menu parameters opens a horizontal bar graph. The bar graph indicates the position the current parameter setting falls within the entire parameter range. The setting appears to the right of the parameter name in the on-screen and front-panel displays.
Basic Operation AV1 COMMAND BANK ACTIVATION The remote control buttons perform different commands depending on which command bank is activated. The remote control contains three command banks: • • • default S1 (Shift 1) S2 (Shift 2) The default command bank remains activated unless the Shift 1 or Shift 2 command bank is activated. The Shift 1 and Shift 2 buttons themselves do not send commands to the AV1. When pressed and held, these buttons activate the associated command bank.
Basic Operation JBL Performance 2 1 COMMAND MATRIX 4 5 The command matrix describes the commands remote control buttons perform when each command bank is active. 3 6 7 2-10 Button Main Zone Shift 1 Shift 2 1 Deactivates standby mode and activates the AV1. Reserved for possible future expansion. Reserved for possible future expansion. 2 Activates standby mode and deactivates the AV1. Reserved for possible future expansion. Reserved for possible future expansion.
Basic Operation AV1 Button Main Zone Shift 2 9 Scroll upward ( ) and downward ( ) through menu items. Adjust the AUDIO CONTROLS menu FADER parameter forward ( ) and backward ( ). Increase ( ) and decrease ( ) the output level of the audio output connector labeled Subwoofer as applied to the activated listening mode. 10 Closes the current menu. Adjusts the AUDIO CONTROLS menu BALANCE parameter left. Reserved for possible future expansion.
Basic Operation JBL Performance Button 16 Main Zone Shift 1 Shift 2 Selects the DVD1 input. Increases the AUDIO CONTROLS menu BASS parameter in 0.5dB increments. Reserved for possible future expansion. Selects the DVD2 input. Increases the AUDIO CONTROLS menu TREBLE parameter in 0.5dB increments. Reserved for possible future expansion. Selects the Sat input. Increases the AUDIO CONTROLS menu TILT EQ parameter in 0.2dB increments. Reserved for possible future expansion. Selects the VCR input.
Basic Operation AV1 Button 17 17 19 Main Zone Shift 1 Shift 2 Selects the LOGIC7 Film mode family. Selects the PANORAMA listening mode. Selects the PARTY listening mode. Selects the DOLBY mode family. See “S1+ Dolby” (next page) for more information. Selects the PLII MOVIE listening mode. Selects the DTS(-ES) mode family. See “S1+ DTS” (next page) for more information. Selects the DTS Neo:6 CIN listening mode. Selects the THX mode family. See “S1+ THX” (next page) for more information.
Basic Operation S1 + DOLBY When the Shift command bank is activated, pressing the remote control DOLBY button while a 5.1-channel Dolby Digital input source is present activates the DOLBY DIGITAL EX or DOLBY DIGITAL listening mode. Subsequent presses toggle the EX DECODING parameter, cycling through the AUTO, ON and OFF settings.
Basic Operation AV1 If the STATUS menu includes a second page, the PG1 indicator appears in the top-right corner of the menu. While pressing the S1 button, press and release the Stat button to open the second page. If the STATUS menu does not include a second page, pressing and releasing the Stat button closes the menu. If this occurs, begin again with step 1. 3. When the desired STATUS menu page has been opened, release the S1 button to deactivate the Shift command bank. 4.
Basic Operation JBL Performance D STATUS STATUS • Provides information about Dolby Digital input sources. • Provides information about DTS(-ES) input sources. • Features L, C, R, SL, SR and SUB level meters. • Features L, C, R, SL, SR, SB and SUB level meters. The SB level meter appears when a 6.1-channel input source is present, or when a 5.1-channel input source is present and the ES DECODING parameter (page 5-30) is set to ON.
Basic Operation AV1 5.1a BYPASS STATUS 2CH BYPASS STATUS Provides information about 5.1-channel analog input sources. Provides information about 2-channel analog input sources when the ADVANCED menu 2-CH ANLG BYP parameter is set to ON. Parameter Possible Settings INPUT The selected input Parameter Possible Settings MODE 5.
Basic Operation JBL Performance DIGITAL STATUS STATUS MENU PARAMETER DESCRIPTIONS Provides information about digital input sources for which a sample rate is detected, but no audio is present in the input signal. Parameter Possible Settings INPUT The selected input MODE The activated listening mode INPUT TYPE --- SAMPLE RATE 44.1kHz, 48kHz, 88.2kHz, 96kHz See “Status Menu Parameter Descriptions” on page 3-18 for detailed information. DIGITAL STATUS INPUT MODE INPUT TYPE SAMPLE RATE 2.
Basic Operation AV1 Possible settings for Dolby Digital input sources include 3/2.1, 3/2, 3/1, 2/2, 2/1, 2/0 and 1/0. Current settings for DTS(-ES) input sources include 3/3.1 and 3/2.1. INPUT DIALOG OFFSET INPUT TYPE -27 to +4dB Indicates the dialog normalization value applied to the input signal. Dolby Digital input sources reproduce dialog at 27 decibels below fullscale (-27dBFS).
Basic Operation WORD LENGTH JBL Performance 16 bits, 20 bits, 24 bits Indicates the word length of the audio data present in the input signal. STATUS MENU LEVEL METERS Most STATUS menus contain level meters that indicate fluctuating input levels in the front left (L), center (C), front right (R), surround left (SL), surround right (SR), surround back (SB) and subwoofer (SUB) channels. These level meters indicate input levels for both analog and digital input sources.
3 Setup Setup .........................................................................................3-2 Input Setup ................................................................................3-3 Changing Input Names (Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Assigning Audio & Video Input Connectors . . . . . . . . . . . . . . . . . . . . . . . 3-6 Selecting Preferred Listening Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup JBL Performance SETUP REAR PANEL CONFIG SETUP Selecting the MAIN MENU SETUP option opens the SETUP menu as shown below. MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUTS SETUP INPUTS Opens the REAR PANEL CONFIG menu, which can be used to configure the analog audio input connectors as eight stereo connectors, five stereo and one 5.1-channel connectors, or two stereo and two 5.1-channel connectors.
Setup AV1 INPUT SETUP SETUP INPUTS (INPUT) INPUT SETUP Selecting the SETUP menu INPUTS option prompts the selection of the desired input (for example, DVD1). Selecting an input opens the corresponding INPUT SETUP menu, which can be used to change input names, assign audio and video input connectors, select preferred listening modes, and configure advanced settings.
Setup JBL Performance CHANGING INPUT NAMES (NAME) Selecting the INPUT SETUP menu NAME parameter opens the INPUT NAME menu, which can be used to customize or restore the factory-default name of the selected input. Factory-default input names correspond to front-panel and remote control input selection button labels.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 INPUT NAME MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.1 FILM D FILM ADVANCED EDIT INPUT NAME RESTORE DEFAULT NAME The custom input name appears in the on-screen and front-panel displays.
Setup JBL Performance ASSIGNING AUDIO & VIDEO INPUT CONNECTORS MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 NAME COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 DIGITAL IN MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup JBL Performance ASSIGNING AUDIO & VIDEO INPUT CONNECTORS SETUP (continued) INPUT SETUP MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ANALOG IN DVD1 ANALOG IN DVD1 ANALOG IN MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 NAME COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ANLG IN LVL MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 NAME DIGITAL IN COAX-1 ANALOG IN NONE AUTO ANLG IN LVL VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM ADVANCED AUTO MANUAL ANLG IN LVL SETUP INPUTS AUTO GAIN dB L 0 -6 -15 -30 ON OFF ON +0.dB +0.
Setup JBL Performance ASSIGNING AUDIO & VIDEO INPUT CONNECTORS MAIN MENU SETUP INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX MANUAL SETUP INPUTS (continued) -18dB to +12dB DVD1 ANGL IN LVL MANUAL Provides manual adjustment of 2-channel analog audio input levels.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 VIDEO IN MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.
Setup JBL Performance ASSIGNING AUDIO & VIDEO INPUT CONNECTORS (continued) MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 COMPONENT MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE AUTO ANLG IN LVL VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.
Setup AV1 SELECTING PREFERRED LISTENING MODES MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 NAME DIGITAL IN COAX-1 ANALOG IN NONE AUTO ANLG IN LVL VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM ADVANCED The INPUT SETUP menus include three preferred listening mode selection parameters labeled 2-CH, DOLBY D, and DTS-ES.
Setup JBL Performance SELECTING PREFERRED LISTENING MODES (continued MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 2-CH MODE MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM 5.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.1 FILM D FILM ADVANCED 5.1 5.1 5.1 D SETUP When the INPUTS DVD1 D Opens the D MODE menu, which selects a preferred listening mode for Dolby Digital input sources.
Setup JBL Performance SELECTING PREFERRED LISTENING MODES (continued) MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup AV1 CONFIGURING ADVANCED SETTINGS MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ADVANCED MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup JBL Performance CONFIGURING ADVANCED SETTINGS MAIN MENU SETUP INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX INPUT SELECT SETUP (continued) INPUTS DIGITAL, ANALOG, AUTO DVD1 ADVANCED INPUT SELECT Controls the interaction of the digital and analog audio input connectors assigned for the selected input.
Setup AV1 INPUT SELECT PARAMETER SETTINGS The table below describes INPUT SELECT parameter settings. DIGITAL ANALOG AUTO The AV1 automatically sets the INPUT SELECT parameter to DIGITAL when the ANALOG IN parameter is set to NONE. The AV1 automatically sets the INPUT SELECT parameter to ANALOG when the DIGITAL IN parameter is set to NONE. The AV1 automatically sets the INPUT SELECT parameter to AUTO when both digital and analog audio input connectors are assigned.
Setup JBL Performance CONFIGURING ADVANCED SETTINGS (continued) MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ADVANCED MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ADVANCED MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup JBL Performance CONFIGURING ADVANCED ZONE SETTINGS MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ADVANCED MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 NAME COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ADVANCED MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 COAX-1 DIGITAL IN NONE ANALOG IN AUTO ANLG IN LVL S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.
Setup JBL Performance SPEAKER SETUP SETUP SPEAKERS SPEAKER SETUP Selecting the SETUP menu SPEAKERS option opens the SPEAKER SETUP menu, which can be used to configure the audio output connectors for the desired speaker setup, set speaker distances and calibrate output levels. The AV1 has eight audio output connectors labeled Front L/R, Center, Subwoofer, Side L/R and Rear L/R.
Setup AV1 In general, low frequencies will be redirected from speakers with the highest crossover points to speakers with the lowest crossover points. Lowfrequency signals lower than the lowest crossover point will be redirected to the subwoofer. If the lowest crossover point is FULL, low-frequency signals, excluding LFE information, will not be redirected to the subwoofer. High-pass Filter High-pass filters attenuate low frequencies at 24dB per octave.
Setup JBL Performance CUSTOM SPEAKER SETUPS (continued) MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP FRONT L/R SPEAKERS MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R 60 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 40 Hz SUBWOOFER ULTRA2 SUB OFF N/A BGC APART ASA FULL 30 Hz 40 Hz 50 Hz 60 Hz 70 Hz 80 Hz 80 Hz 90 Hz 100 Hz 110 Hz 120 Hz R 40Hz SR RR 60Hz 60Hz
Setup AV1 MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP CENTER SPEAKER MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 60 Hz SUBWOOFER 40 Hz ULTRA2 SUB OFF BGC N/A ASA APART FULL 30 Hz 40 Hz 50 Hz 60 Hz 70 Hz 80 Hz 80 Hz 90 Hz 100 Hz 110 Hz 120 Hz R 40Hz SR RR 60Hz 60Hz C 60Hz M SUB 40Hz CENTER SETUP FULL, 30Hz TO 120
Setup JBL Performance CUSTOM SPEAKER SETUPS (continued) MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP SIDE L/R SPEAKERS MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION FRONT L/R 40 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 60 Hz SUBWOOFER 40 Hz ULTRA2 SUB OFF BGC N/A ASA APART FULL 30 Hz 40 Hz 50 Hz 60 Hz 70 Hz 80 Hz 80 Hz 90 Hz 100 Hz 110 Hz 120 Hz R 40Hz SR RR 60Hz 60Hz
Setup AV1 MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP REAR L/R SPEAKERS MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R 60 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 40 Hz SUBWOOFER ULTRA2 SUB OFF N/A BGC APART ASA FULL 30 Hz 40 Hz 50 Hz 60 Hz 70 Hz 80 Hz 80 Hz 90 Hz 100 Hz 110 Hz 120 Hz R 40Hz SR RR 60Hz 60Hz C 60Hz M SUB 40Hz REAR L/R SETUP SPEAKERS FU
Setup JBL Performance CUSTOM SPEAKER SETUPS (continued) MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP SUBWOOFER MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R 60 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 40 Hz SUBWOOFER ULTRA2 SUB OFF N/A BGC APART ASA FULL 30 Hz 40 Hz 50 Hz 60 Hz 70 Hz 80 Hz 80 Hz 90 Hz 100 Hz 110 Hz 120 Hz R 40Hz SR RR 60Hz 60Hz C 60Hz
Setup AV1 MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R 60 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 40 Hz SUBWOOFER ULTRA2 SUB OFF N/A BGC APART ASA R 40Hz SR RR 60Hz 60Hz C ON OFF The BGC parameter is not available unless the THX ULTRA2 SUB parameter is set to OFF.
Setup JBL Performance CUSTOM SPEAKER SETUPS (continued) MAIN MENU SETUP SPEAKER SETUP CUSTOM SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION 40 Hz FRONT L/R 60 Hz CENTER 60 Hz SIDE L/R 60 Hz REAR L/R 40 Hz SUBWOOFER ULTRA2 SUB OFF N/A BGC APART ASA R 40Hz SR RR 60Hz 60Hz C 60Hz The ASA parameter is available on the CUSTOM and THX SETUP menus.
Setup AV1 THX SPEAKER SETUPS SETUP SPEAKERS THX SETUP MAIN MENU SETUP SPEAKER SETUP THX SPEAKER SETUP THX SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION !CAUTION! PRESSING THE BUTTON WILL AUTOMATICALLY CHANGE THE OUTPUTS TO A THX SPEAKER CONFIGURATION 40 Hz FRONT L/R* 60 Hz CENTER* 60 Hz SIDE L/R* 60 Hz REAR L/R* 40 Hz SUBWOOFER* ULTRA2 SUB OFF N/A BGC APART ASA
Setup JBL Performance THX SPEAKER SETUPS (continued) MAIN MENU SETUP SPEAKER SETUP THX SPEAKER SETUP THX SETUP THX REAR SPEAKERS MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION !CAUTION! PRESSING THE BUTTON WILL AUTOMATICALLY CHANGE THE OUTPUTS TO A THX SPEAKER CONFIGURATION 40 Hz FRONT L/R* 60 Hz CENTER* 60 Hz SIDE L/R* 60 Hz REAR L/R 40 Hz SUBWOOFER* ULTRA2 SUB OFF N/A
Setup AV1 MEASURING SPEAKER DISTANCES SETUP SPEAKERS SPEAKER DISTANCES MAIN MENU SETUP SPEAKER SETUP SPEAKER DISTANCES MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER UNITS R 0.0 ft SR RR 0.0 ft 0.0 ft C 30.0 ft M SUB 0.
Setup JBL Performance MEASURING SPEAKER DISTANCES (continued) MAIN MENU SETUP SPEAKER SETUP SPEAKER DISTANCES MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER UNITS R 0.0 dB SR RR 0.0 dB 0.0 dB C 0.0 dB M SUB 0.0 dB FRONT LEFT & RIGHT SETUP SPEAKERS 0.0 to 30.0 ft or 0.0 to 12.
Setup AV1 CALIBRATING OUTPUT LEVELS SETUP SPEAKERS LEVELS CALIBRATION MAIN MENU SETUP SPEAKER SETUP LEVELS CALIBRATION MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER R 0.0 dB SR INTERNAL NOISE !CAUTION! HIGH AUDIO LEVELS RR 0.0 dB 0.
Setup CALIBRATING OUTPUT LEVELS JBL Performance (continued) Note: The AV1 automatically sets volume level to +0dB when the internal noise test begins. Avoid adjusting master volume level while the test is in progress to achieve a 75dB THX reference level (a 75dB SPL meter reading). When the internal noise test is conducted, a calibration test signal travels to the audio output connectors in the order listed on the SPEAKER LEVEL ADJUST menu.
Setup AV1 EXTERNAL NOISE TEST SETUP SPEAKERS LEVELS CALIBRATION EXTERNAL NOISE TEST MAIN MENU SETUP SPEAKER SETUP LEVELS CALIBRATION SPEAKER LEVEL ADJUST MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER R 0.0 dB SR RR 0.0 dB 0.
Setup JBL Performance SPEAKER LEVEL ADJUST SIDE LEFT & RIGHT SPEAKER LEVEL ADJUST is used to adjust output levels during the internal and external noise tests. Parameter Default Setting Possible Settings FRONT LEFT 0.0dB -18.0 to +12.0dB CENTER 0.0dB -18.0 to +12.0dB FRONT RIGHT 0.0dB -18.0 to +12.0dB SIDE RIGHT 0.0dB -18.0 to +12.0dB REAR RIGHT 0.0dB -18.0 to +12.0dB REAR LEFT 0.0dB -18.0 to +12.0dB SIDE LEFT 0.0dB -18.0 to +12.0dB SUBWOOFER 0.0dB -18.0 to +12.
Setup AV1 MAIN MENU SETUP SPEAKER SETUP LEVELS CALIBRATION BASS PEAK LIMITER MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER CAL NOISE LIMITER LIMIT ADJ R 0.0 dB SR ON OFF !CAUTION! HIGH AUDIO LEVELS RR 0.0 dB 0.0 dB ON ON 100dB C 0.0 dB M SUB 0.0 dB L 0.0 dB SL RL 0.
Setup JBL Performance SPEAKER LEVEL ADJUST MENU (continued) MAIN MENU SETUP SPEAKER SETUP LEVELS CALIBRATION BASS PEAK LIMITER MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER CAL NOISE LIMITER LIMIT ADJ R SR ON OFF !CAUTION! HIGH AUDIO LEVELS RR 0.0 dB 0.0 dB 0.0 dB ON ON 100dB C 60Hz M SUB 0.
Setup AV1 REAR PANEL CONFIG SETUP REAR PANEL CONFIG Selecting the SETUP menu REAR PANEL CONFIG option opens the REAR PANEL CONFIG menu, which is used to configure the analog audio input connectors as eight stereo connectors, one 5.1-channel and five stereo connectors or two 5.1-channel and two stereo connectors. MAIN MENU SETUP REAR PANEL CONFIG MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS 8 STEREO INPUTS OR 5 ST. & (1) 5.
Setup JBL Performance 5 ST. & (1) 5.1 ANLG (continued) SETUP REAR PANEL CONFIG 5 ST. & (1) 5.1 ANLG 2 ST. & (2) 5.1 ANLG SETUP REAR PANEL CONFIG 2 ST. & (2) 5.1 ANLG When the analog audio input connectors are configured as five stereo and one 5.1-channel connectors: Configures the analog audio input connectors as two stereo and two 5.1-channel connectors. Two-channel sources assigned to the stereo connectors are reassigned to the corresponding 5.1-channel connectors. The 5.
Setup AV1 DISPLAY SETUP SETUP DISPLAYS Selecting the SETUP menu DISPLAYS option opens the DISPLAY SETUP menu, which is used to customize the on-screen and front-panel displays, restore audio/video synchronization, and activate and create a custom unit name.
Setup JBL Performance (continued) MAIN MENU SETUP DISPLAY SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS ON-SCREEN DISPLAY FRONT PANEL DISPLAY OFF A/V SYNC DELAY OFF CUSTOM NAME EDIT CUSTOM NAME CUSTOM NAME SETUP DISPLAYS ON, OFF CUSTOM NAME Activates the display of a custom unit name, which appears when the AV1 is activated.
Setup AV1 ON-SCREEN DISPLAY SETUP SETUP DISPLAYS ON-SCREEN DISPLAY MAIN MENU SETUP DISPLAY SETUP ON-SCREEN DISPLAY MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME 2 SECONDS STATUS TOP POSITION NTSC FORMAT ON BACKGROUND ON REMOTE STATE Selecting the DISPLAY SETUP menu ON-SCREEN DISPLAY option opens the ON-SCREEN DISPLAY menu, which is used to
Setup JBL Performance ON-SCREEN DISPLAY SETUP MAIN MENU SETUP DISPLAY SETUP ON-SCREEN DISPLAY MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF OFF CUSTOM NAME EDIT CUSTOM NAME 2 SECONDS STATUS TOP POSITION NTSC FORMAT ON BACKGROUND ON REMOTE STATE POSITION SETUP DISPLAYS (continued) TOP, CENTER, BOTTOM ON-SCREEN DISPLAY 3-48 FORMAT POSITION SETUP Controls the vertical po
Setup AV1 MAIN MENU SETUP DISPLAY SETUP ON-SCREEN DISPLAY MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF OFF CUSTOM NAME EDIT CUSTOM NAME 2 SECONDS STATUS TOP POSITION NTSC FORMAT ON BACKGROUND ON REMOTE STATE BACKGROUND SETUP DISPLAYS ON, OFF ON-SCREEN DISPLAY BACK GROUND ON OFF REMOTE STATE SETUP DISPLAYS ON, OFF ON-SCREEN DISPLAY REMOTE STATE Activates and deactiva
Setup JBL Performance FRONT PANEL DISPLAY SETUP SETUP DISPLAYS FRONT PANEL DISPLAY Opens the FRONT PANEL DISPLAY menu, which is used to customize the front-panel display.
Setup AV1 VOLUME CONTROL SETUP SETUP VOLUME CONTROLS Selecting the SETUP menu VOLUME CONTROLS option opens the VOLUME CONTROL SETUP menu, which is used to configure volume and mute levels.
Setup JBL Performance TRIGGER SETUP SETUP TRIGGER Selecting the SETUP menu TRIGGER option opens the TRIGGER SETUP menu, which is used to configure the programmable trigger output (Trigger 1) in the 5-pin DIN connector located on the back panel. The 5-pin DIN connector provides 12VDC outputs for externally controlling compatible components. The Power Trigger pin cannot be configured and is active when the AV1 is active (not in Standby).
Setup AV1 PROGRAM OPERATION PARAMETERS SETUP TRIGGER ON, OFF (PROGRAM OPERATION PARAMETERS) Configures Trigger 1 for program operation. All TRIGGER SETUP menu parameters – except the REMOTE ONLY parameter – are considered program operation parameters. The connector can be associated with multiple inputs and listening modes at the same time. When the REMOTE ONLY parameter is OFF and program operation parameters are ON, Trigger 1 is associated with the corresponding listening modes.
Setup JBL Performance LOCK OPTIONS SETUP LOCK OPTIONS Selecting the SETUP menu LOCK OPTIONS option opens the LOCK OPTIONS menu, which is used to lock and unlock settings in the MODE ADJUST, AUDIO CONTROLS and SETUP menu branches.
4 Audio Controls Audio Controls ............................................................................
Audio Controls JBL Performance AUDIO CONTROLS Selecting the MAIN MENU AUDIO CONTROLS option opens the AUDIO CONTROLS menu, which can be used to customize the audio output connectors. These parameter settings affect all inputs and listening modes selected, except the 5.1a BYPASS and 2CH BYPASS listening modes. MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER to +6.0dB BASS Default Parameter Possible Value Settings BASS +0.0dB -6.0dB to +6.
Audio Controls AV1 BASS Parameter Settings The BASS parameter controls the amount of low-frequency boost or cut applied to the audio output connectors labeled Front L/R, Center and Subwoofer. TREBLE Parameter Settings The TREBLE parameter controls the amount of boost or cut applied to the audio output connectors labeled Front L/R and Center.
Audio Controls AUDIO CONTROLS JBL Performance (continued) MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER TILT EQ AUDIO CONTROLS -3.0 to +3.0dB +0.0dB +0.0dB +0.0dB OFF -3.0dB to +3.0dB TILT EQ Controls the amount of tilt equalization applied to the audio output connectors labeled Front L/R, Center and Subwoofer. This parameter setting affects the entire frequency spectrum with a hinge point at 1kHz.
Audio Controls AV1 TILT EQ Parameter Settings The TILT EQ parameter controls the amount of tilt equalization applied to the audio output connectors labeled Front L/R, Center and Subwoofer. LOUDNESS Parameter Settings The LOUDNESS parameter controls the amount of low-frequency boost that is automatically applied to the audio output connectors labeled Front L/R, Center and Subwoofer.
Audio Controls AUDIO CONTROLS JBL Performance (continued) MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER BALANCE AUDIO CONTROLS L< >R +0.0dB +0.0dB +0.0dB OFF L to R BALANCE Controls the left-to-right balance of the audio output connectors.
5 Mode Adjust Mode Adjust ...............................................................................5-2 Listening Mode Activation...........................................................5-2 Listening Mode Descriptions .......................................................5-4 Listening Mode Menu Option & Parameter Descriptions...........
Mode Adjust 5-2 JBL Performance MAIN MENU MODE ADJUST MODE ADJUST AUDIO CONTROLS SETUP FILM TV MUSIC MUSIC SURR PLII MOVIE PLII MUSIC PLII + PRO LOGIC PL + CIN MUSIC + NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC SurEX MUSIC DIGITAL EX* 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM* MUSIC* * MUSIC * 2-CHAN* 5.
Mode Adjust AV1 PREFERRED LISTENING MODE SELECTION PARAMETERS The INPUT SETUP menus include four preferred listening mode selection parameters labeled 2-CH, DOLBY D, DTS(-ES) and 5.1a. These parameters can be used to select a preferred listening mode for 2-channel, Dolby Digital, DTSDTS(-ES) and 5.1a input sources. The AV1 automatically activates the selected listening mode whenever a new input is selected or a new input source is present.
Mode Adjust JBL Performance LISTENING MODE DESCRIPTIONS FILM MODE ADJUST TV FILM MODE ADJUST TV • A proprietary listening mode. • A proprietary listening mode. • Designed for enhanced playback of 2-channel stereo or matrix-encoded film sources. • Based on the L7 FILM listening mode, but specifically tailored for broadcast sources.
Mode Adjust AV1 MUSIC MODE ADJUST MUSIC SURR MODE ADJUST MUSIC MUSIC SURR • A proprietary listening mode. • A proprietary listening mode • Designed for playback of 2-channel stereo or matrix-encoded music sources. • • Recommended for 2-channel music sources. Designed for playback of 2-channel stereo music sources recorded in real spaces and for playback of recordings that contain added reverb. • Extracts ambient sounds from the input source and sends these sounds to all speakers.
Mode Adjust JBL Performance PLII MOVIE MODE ADJUST • PLII MOVIE Similar to the PRO LOGIC listening mode, but uses full-frequency stereo surround channels to realistically increase the perceived width of the listening space. • Designed for playback of Dolby Surround-encoded sources. • Decodes five channels from Dolby Surround-encoded sources. • Provides impressive enhancement compared to Dolby Pro Logic decoding.
Mode Adjust AV1 PRO LOGIC PLII + MODE ADJUST MODE ADJUST PLII + PRO LOGIC • Designed for playback of Dolby Surround-encoded sources. • Designed for playback of Dolby Surround-encoded sources. • Uses Dolby Pro Logic II decoding to derive five channels from Dolby Surround-encoded sources. • Decodes four channels from Dolby Surround-encoded sources. • • Applies THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters.
Mode Adjust JBL Performance PL + MODE ADJUST CIN MODE ADJUST PL + • Designed for playback of Dolby Surround-encoded sources. • Decodes four channels from Dolby Surround-encoded sources. • Uses a mono surround channel with a high-frequency rolloff above 7kHz. • Applies THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters. Most films are mixed for movie theaters, and might sound too bright when played back in home theaters without re-equalization.
Mode Adjust AV1 MUSIC MODE ADJUST + MUSIC MODE ADJUST + • Designed for playback of matrix-encoded digital stereo music sources. • Designed for playback of matrix-encoded digital stereo film sources. • Derives six channels when both side and rear speakers are present (rear channels will be in parallel). Derives five channels when only side or rear speakers are present. The subwoofer channel is generated through bass management in the AV1.
Mode Adjust JBL Performance NIGHTCLUB MODE ADJUST • CONCERT HALL NIGHTCLUB MODE ADJUST Designed for playback of “dry” music sources that benefit from the addition of room reflections, especially music sources that lack ambience in the recording. • Generates early reflections to simulate small, intimate listening spaces. • Sends early reflections to the front, side and rear channels.
Mode Adjust AV1 CHURCH MODE ADJUST • • CATHEDRAL MODE ADJUST CHURCH CATHEDRAL Uses a reverb algorithm to emphasize the rich, smooth, reverberant decay characteristic of small and medium listening spaces with long reverberation time relative to their size, such as churches and chambers. • Similar to the CHURCH listening mode.
Mode Adjust JBL Performance PANORAMA MODE ADJUST PANORAMA CALIBRATION PANORAMA MODE ADJUST PANORAMA CALIBRATION • Designed for playback of stereo and matrix-encoded sources. • • Uses proprietary algorithms to move the stereo image outward from the front speakers, producing a wider stereo field with greater depth. The PANORAMA listening mode must be calibrated to take full advantage of its effects.
Mode Adjust AV1 Negative settings (-127 to -1) compensate for primary listening positions located to the left of the center between the front left and right speakers. The +0 setting indicates a primary listening position centered between the front left and right speakers. 6. When playback of the calibration source is in progress, set the SPEAKER ANGLE parameter (next column) so the sound is not heard in the left ear. 7. Set the SOURCE parameter to LEFT. 8.
Mode Adjust PANORAMA CALIBRATION JBL Performance (continued) PARTY MODE ADJUST SPEAKER ANGLE 10deg to 90deg Compensates for a wide or narrow speaker angle relative to the primary listening position. Select the setting closest to the angle between the front left and right speakers and the primary listening position. PARTY • Designed for playback of stereo sources. • Sends stereo sources to all channels. • Recommended for background music.
Mode Adjust AV1 MONO LOGIC MODE ADJUST MONO MONO LOGIC MODE ADJUST MONO • Designed for playback of mono sources. • Designed for playback of mono sources. • Uses proprietary reverb algorithms to realistically expand mono sources to use all channels, dramatically increasing the perceived width and sense of envelopment of the listening space. • Sends mono sources to the center channel.
Mode Adjust 5.1 JBL Performance FILM MODE ADJUST 5.1 5.1 FILM TV MODE ADJUST 5.1 TV • A proprietary listening mode. • A proprietary listening mode. • Designed for playback of 5.1-channel Dolby Digital-encoded film sources. • Based on the 5.1 L7 FILM listening mode, but specifically tailored for broadcast sources. • Derives seven channels from 5.1-channel input sources. When both side and rear speakers are present, the 5.
Mode Adjust AV1 5.1 MUSIC MODE ADJUST 5.1 , MUSIC MODE ADJUST ULTRA2, & or SUREX ULTRA2 or 5.1 SurEX • A proprietary listening mode. • • Based on the 5.1 L7 FILM listening mode, but specifically tailored for music sources. Designed for playback of 5.1-channel Dolby Digital film sources. • • Designed for playback of 5.1-channel Dolby Digital-encoded music sources. • Recommended for 5.1-channel Dolby Digital-encoded music sources.
Mode Adjust JBL Performance Option/Parameter Default Setting Possible Settings • RE-EQUALIZER ON ON, OFF Listening mode name differs depending on the encoding present in the input source, the SURROUND EX parameter setting and the speaker setup. SURROUND EX AUTO AUTO, ON, OFF – COMPRESSION OFF AUTO, ON, OFF The THX ULTRA2 listening mode is available when THX Ultra2 decoding is engaged. LFE MIX +0.0dB -10.0dB to +0.
Mode Adjust AV1 MUSIC MODE ADJUST DIGITAL & MUSIC MODE ADJUST • Designed for playback of 5.1-channel Dolby Digital music sources. • The 5.1 THX MUSIC listening mode cannot be activated unless side and rear speakers are present. • ASA processing is applied to signals sent to the rear speakers. See “ASA” on page 3-32 for more information. • Recommended for home theaters with THX-certified speaker setups.
Mode Adjust JBL Performance The table below indicates the conditions in which Dolby Digital Surround EX decoding is engaged. • Dolby Digital Surround EX decoding is engaged when the EX DECODING parameter is set to ON, or the EX DECODING parameter is set to AUTO and a flagged 5.1-channel Dolby Digital source recorded with Dolby Digital Surround EX is detected.
Mode Adjust AV1 5.1 2-CHANNEL MODE ADJUST 5.1 MONO LOGIC 5.1 2-CHANNEL MODE ADJUST • Designed for converting 5.1-channel Dolby Digital-encoded input sources into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.1-channel Dolby Digital input signals to the front speakers and subwoofer. • Recommended for recording purposes. 5.1 MONO LOGIC • Designed for playback of Dolby Digital-encoded mono sources.
Mode Adjust 5.1 MONO SURR MODE ADJUST 5.1 MONO SURR JBL Performance 5.1 MONO MODE ADJUST 5.1 MONO • Designed for playback of Dolby Digital-encoded mono sources. • Designed for playback of Dolby Digital-encoded mono sources. • Sends mono signals to all channels. • Sends a mono signal to the center channel.
Mode Adjust AV1 Note: DECODING The table below indicates the conditions in which DTS-ES decoding is engaged. • DTS-ES decoding is engaged when the ES DECODING parameter is set to ON, or the ES DECODING parameter is set to AUTO and a 5.1-channel matrix-encoded or 6.1-channel discrete-encoded DTS-ES source is detected. • DTS-ES decoding is not engaged when the ES DECODING parameter is set to OFF, or the ES DECODING parameter is set to AUTO and a 5.1-channel DTS source is detected.
Mode Adjust JBL Performance FILM MODE ADJUST MUSIC FILM MODE ADJUST MUSIC • A proprietary listening mode. • A proprietary listening mode. • Designed for playback of 5.1- and 6.1-channel DTS(-ES) film sources. • Designed for playback of 5.1- and 6.1-channel DTS(-ES) music sources. • Uses an advanced matrix to derive seven channels from 5.1and 6.1-channel DTS(-ES) sources.
Mode Adjust AV1 to the ASA parameter description on page 3-37 for more information. ULTRA2 & MODE ADJUST ULTRA2 or • Designed for playback of 5.1-channel DTS, 5.1-channel matrix-encoded DTS-ES and 6.1-channel discrete-encoded DTS-ES film sources. • Listening mode name differs depending on the encoding present in the input source, the ES DECODING parameter setting and the speaker setup. The table below indicates the conditions in which THX Ultra2 and DTS-ES decoding are engaged.
Mode Adjust The table at the bottom of the previous page indicates the conditions in which THX Ultra2 and DTS-ES decoding are engaged. JBL Performance MUSIC MODE ADJUST MUSIC • THX Ultra2 decoding is engaged when the ES DECODING parameter is set to OFF, or the ES DECODING parameter is set to AUTO and a 5.1-channel DTS source is detected. • Designed for playback of 5.1-channel DTS music sources.
Mode Adjust AV1 2-CHAN MODE ADJUST MODE ADJUST 2-CHAN • Designed for playback of 5.1- and 6.1-channel DTS(-ES) sources. • Designed for converting 5.1- or 6.1-channel DTS(-ES) sources into 2-channel LOGIC7-encoded output signals. • Decodes 5.1 matrix or 6.1 discrete channels from DTS(-ES) sources. The six main channels are full-frequency. The .1 channel, often referred to as LFE information, has a limited frequency range of 120Hz. • Sends downmixed 5.1- or 6.
Mode Adjust JBL Performance 5.1a BYPASS MODE ADJUST 2CH BYPASS MODE ADJUST 5.1a BYPASS • Designed for playback of 5.1-channel analog sources, such as DVD-A or SACD players. • The 5.1-channel analog input connectors are sent directly to the volume control and audio output connectors as shown on page 3-49. These signals receive no internal processing. • When both side and rear speakers are present, surround channel signals are sent in parallel to the side and rear speakers.
Mode Adjust AV1 LISTENING MODE MENU OPTION & PARAMETER DESCRIPTIONS 5 SPKR ENHANCE ON, OFF Simulates 7-channel playback in 5-channel speaker configurations. When set to ON, the AV1 provides an increased sense of spaciousness and envelopment through the surround speakers. This enhancement is most noticeable when the surround speakers are positioned to the side of the primary listening position, or when the primary listening position is located against the rear wall.
Mode Adjust JBL Performance LISTENING MODE MENU OPTION & PARAMETER DESCRIPTIONS BASS RT 5ms to 48.6s Works with the MID RT and SIZE parameters to adjust the amount of time required for low-frequency information to decay below 60dB in level. The BASS RT parameter setting should match the MID RT parameter setting for more natural effects in smaller listening spaces. CAUTION! (continued) CENTER MIX -25dB to +5dB Indicates the relative center channel level for downmixing.
Mode Adjust AV1 CUSTOM VS PRESET MODE ADJUST (Listening Mode) DIMENSION CUSTOM CUSTOM VS PRESET Allows comparison listening to the custom and factory-default versions of the selected listening mode. When PRESET is selected, the listening mode is heard in its factory-default condition – as if all parameters had been restored to their factory-default settings. No parameter settings are affected when this option is selected.
Mode Adjust JBL Performance When the Shift command bank is activated, pressing the remote control DTS button while a DTS(-ES) input source is present toggles the ES DECODING parameter, cycling through the AUTO, ON and OFF settings. Note: The DTS(-ES) STATUS menu includes the SB level meter when: • The ES DECODING parameter is set to ON and a 5.1-channel DTS source is present. • The ES DECODING parameter is set to AUTO and a 5.1-channel matrix-encoded or 6.
Mode Adjust AV1 LFE MIX -20.0dB or -10.0dB to +0.0dB Controls the output level of LFE information – the .1 channel in a 5.1or 6.1-channel input source – that is sent to the audio output labeled Subwoofer. Low frequencies from up to seven other channels might be combined with the LFE information to create the subwoofer output signal, which significantly increases subwoofer output levels.
Mode Adjust PANORAMA JBL Performance ON, OFF REAR L/R When set to ON, extends the front stereo image to include surround channel signals, which creates a “wraparound” effect with side wall imaging. MODE ADJUST Note: OFF, 1ms to 100ms Adjusts delay time between the direct sound and the onset of reverberation. Higher settings make the simulated space sound larger.
Mode Adjust AV1 ROLLOFF 500Hz to 20.0kHz, OFF Simulates the absorption of high frequencies in a real space. It is recommended that you begin with a low setting to simulate highfrequency absorbative spaces. SIDE L/R MODE ADJUST OFF, -30dB to +12dB (Listening Mode) OUTPUT LEVELS SOURCE RIGHT, LEFT & RIGHT, LEFT See “PANORAMA CALIBRATION” on page 5-12 for more information. SPEAKER ANGLE 10deg to 90deg See “PANORAMA CALIBRATION” on page 5-12 for more information.
Mode Adjust SURR ROLLOFF JBL Performance 500Hz to 20.0kHz, OFF Applies high-frequency attenuation control to the audio output connectors labeled Side L/R and Rear L/R. This filter is only applied to output signals generated by the AV1. SURROUND DLY 0ms to 15ms Increases the perceived depth of the listening space by delaying the arrival time of signals from the side and rear speakers. It is recommended that you increase the setting when a greater sense of depth is desired in the listening space.
6 Troubleshooting & Maintenance Troubleshooting..........................................................................6-2 Routine Maintenance ..................................................................6-3 Restoring Factory-default Settings ...............................................
Troubleshooting & Maintenance TROUBLESHOOTING The AV1 does not power on. 1. Attempt to power on the AV1 with the front panel Standby button and remote control On button. 2. Make sure the rear panel power switch is set to the c (“on”) position. 3. Examine the power cord to ensure a good connection between the rear panel AC input connector and the wall outlet. 4. Check the electrical circuit and breaker. JBL Performance 3. Make sure audio has not been muted.
Troubleshooting & Maintenance AV1 The AV1 is powered on, but there is no video. 4. Contact JBL customer service at 888-691-4171. 1. Examine the video cables – particularly the S-video cables – to ensure a good connection to the associated component. Note: 2. Check the INPUT SETUP menu VIDEO IN (page 3-11) and COMPONENT IN (page 3-12) parameters to ensure the appropriate video connector is assigned to the selected input. Visit www.jbl.com for additional troubleshooting information.
Troubleshooting & Maintenance RESTORING FACTORY-DEFAULT SETTINGS When factory-default settings are restored, all parameters and userdefined values are restored to their factory-default settings. Before restoring factory-default settings, it is recommended to record all user-defined settings on the installation worksheet that begins on page A-14. To restore factory-default settings: JBL Performance 5. Press the remote control and arrows to highlight the desired option.
A Appendix Specifications ............................................................................. A-2 Declaration of Conformity.......................................................... A-4 Menu Tree ................................................................................. A-5 Installation Worksheet ..............................................................
Appendix JBL Performance SPECIFICATIONS Audio Input & Output Connectors Video Input & Output Connectors Analog Audio Inputs Video Inputs 5 composite (RCA), 5 S-video, and 3 component video (RCA) Video Outputs 1 composite (RCA), 1 S-video, and 1 component (RCA) Digital Audio Inputs Audio Outputs 8 stereo (RCA) or 5 stereo and one 5.1-channel or 2 stereo and two 5.
Appendix AV1 Component Video Performance Other Compatibility Trigger Outputs 1 power on/off and 1 programmable connector on detachable screw terminals (+12 VDC, 0.5 amps each) RS-232 Serial Input/ Output 2 9-pin D-sub connectors Power Requirements 90-250 VAC, 50-60Hz, 60W (universal line input), detachable power cord AV1 Dimensions & Weight • • • • Rack Mounting Optional brackets are available for installation in a standard 19" equipment rack (2 rack units required for AV1).
Appendix JBL Performance DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC and 93/68/EEC Standard(s) to Which Conformity is Declared: EN55022:1994 + A1:1995 + A2:1997, EN55024:1998, EN61000-3-2: 2000, EN61000-3-3:2000, and EN60065: 1998 Manufacturer: Harman Specialty Group 3 Oak Park Bedford, MA 01730-1413 USA The equipment identified here conforms to the Directive(s) and Standard(s) specified above.
Appendix AV1 MENU TREE This menu tree is based on software version 1.0. TRIGGER SETUP MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP REAR PANEL CONFIG DVD1 DVD2 SAT VCR TV CD TUNER AUX 8 STEREO INPUTS OR 5 ST. & (1) 5.1 ANLG OR 2 ST. & (2) 5.1 ANLG 8 STEREO INPUTS FOR REAR PANEL CFG 5 ST. & (1) 5.1 ANLG FOR REAR PANEL CFG 2 ST. & (2) 5.
Appendix JBL Performance MENU TREE (continued) MAIN MENU SETUP INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP SAT INPUT SETUP TV INPUT SETUP TUNER INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH D 5.
Appendix AV1 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS DVD1 DVD2 SAT VCR TV CD TUNER AUX NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.1 FILM D Selecting an INPUT SETUP menu item opens the corresponding menu shown below. These menus are identical regardless of which input is selected.
Appendix JBL Performance MENU TREE (continued) MAIN MENU SETUP SPEAKER SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 40Hz SR Selecting a SPEAKER SETUP menu option opens the corresponding menu shown below and to the right (for example, selecting the CUSTOM SETUP option opens the CUSTOM SETUP menu shown below).
Appendix AV1 MAIN MENU SETUP SPEAKER SETUP MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 40Hz SR RR 60Hz 60Hz LEVELS CALIBRATION C 60Hz M SUB 40Hz L 40Hz SL RL 60Hz 60Hz INTERNAL NOISE !CAUTION! HIGH AUDIO LEVELS INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER SPEAKER LEVEL ADJUST BASS PEAK LIMITER FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT R
Appendix JBL Performance MENU TREE (continued)) MAIN MENU MODE ADJUST MODE ADJUST AUDIO CONTROLS SETUP FILM TV MUSIC MUSIC SURR PLII MOVIE PLII MUSIC PLII + PRO LOGIC 0 PL + CIN MUSIC + NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC SurEX MUSIC DIGITAL EX* 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM* MUSIC* * MUSIC * 2-CHAN* 5.
Appendix AV1 5.1 2-CHANNEL SUB LEVEL CUSTOM +0dB MONO LOGIC EFFECT LVL -9dB ACADMY FILTER ON SURR ROLLOFF 3.1kHz OUTPUT LEVELS CUSTOM 5.1 MONO SURROUND OUTPUT LEVELS CUSTOM MONO SUB LEVEL CUSTOM 5.1 +0dB FILM VOCAL ENHANCE +0.0dB 5 SPKR ENHANCE ON BASS ENHANCE OFF RE-EQUALIZER ON REAR DLY OFFSET 15ms COMPRESSION OFF LFE MIX +0.0dB OUTPUT LEVELS CUSTOM TV VOCAL ENHANCE +0.0dB 5 SPKR ENHANCE ON BASS ENHANCE OFF RE-EQUALIZER ON REAR DLY OFFSET 15ms COMPRESSION OFF LFE MIX +0.
Appendix JBL Performance MENU TREE (continued) 5 SPKR ENHANCE ON OFF ACADEMY FILTER ON OFF AUTO AZIMUTH ON OFF BASS CONTENT CALIBRATION CNTR DLY SAMPLES PANORAMA CALIBRATION SOURCE LEFT & RIGHT SPEAKER ANGLE 30deg LISTENER POS +0 COMPRESSION -127 CTR WIDTH +127 10 to 90deg RIGHT LEFT & RIGHT LEFT BINAURL MONO STEREO BASS ENHANCE CENTER DEPTH PRESET CUSTOM MASTER LEVEL FRONT STEERING -25 to +5dB DIMENSION FRONT REAT NEUTRAL OFF, 1 to 100ms RE-EQUALIZER MID RT OFF MSURR MUSIC FILM O
Appendix AV1 SOUND STAGE FRONT NEUTRAL REAR SPEECH DETECT ON OFF SUB LEVEL OFF, -30 to +12dB SURR ROLLOFF 500Hz to 20.0 kHz, OFF SURROUND DLY 0 to15ms SURROUND EX AUTO ON OFF SURROUND MIX -5 to + 5dB VOCAL ENHANCE +6.0dB +3.0dB +6.0dB Activating the AV1 while pressing and holding the front-panel or remote control Mute button opens the FACTORY SETTINGS menu shown below. Refer to page 6-4 for more information.
Appendix JBL Performance INSTALLATION WORKSHEET INPUT SETUP NAME DIGITAL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2-CH D ADVANCED INPUT SELECTION 2-CH ANLG BYP S-VIDEO 16:9 S-VIDEO 4:3 OSD COMPONENT OSD A-14 DVD1 DVD2 SAT VCR TV CD TUNER AUX
Appendix AV1 SPEAKER SETUP CUSTOM SETUP THX SETUP FRONT LEFT/RIGHT THX 80hZ CENTER THX 80hZ SIDE LEFT/RIGHT THX 80hZ SPEAKER DISTANCES LEVELS CALIBRATION REAR LEFT/RIGHT SUBWOOFER THX 80hZ THX ULTRA2 SUB BGC ASA UNITS CAL NOISE LIMITER LIMIT ADJ REAR PANEL CONFIG Circle One SETTINGS 8 STEREO INPUTS 5 ST. & (1) 5.1 ANLB 2 ST. & (2) 5.
Appendix JBL Performance INSTALLATION WORKSHEET (continued) DISPLAY SETUP SETTING ON-SCREEN DISPLAY TRIGGER SETUP SETTING LOCK OPTIONS REMOTE ONLY SETUP AUDIO CNTRL POSITION If the REMOTE ONLY parameter is set to OFF, circle the inputs and listening modes selected for program operation. FORMAT DVD1 PANORAMA DVD2 2-CH SURROUND SAT 2-CHANNEL VCR MONO LOGIC TV MONO SURROUND CD MONO TUNER 5.1 L7 FILM PHONO 5.1 L7 TV L7 FILM 5.
Index Numerics 2 CH button, 2-13, 3-20 2 ST. & (2) 5.1 ANLG setting, 3-44 2.0 ENCODING parameter, 2-18 2-CH ANLG BYP parameter, 3-20 2CH BYPASS listening mode, 5-28 2CH BYPASS STATUS menu, 2-17 2-CH parameter, 3-14 2CH STATUS menu, 2-15 2-CHANNEL listening mode, 5-14 5 SPKR ENHANCE parameter, 5-29 5 ST. & (1) 5.1 ANLG setting, 3-43 5.1 2-CHANNEL listening mode, 5-21 5.1 L7 FILM listening mode, 5-16 5.1 L7 MUSIC listening mode, 5-17 5.1 L7 TV listening mode, 5-16 5.1 MONO listening mode, 5-22 5.
Index DOLBY button, 2-13 DOLBY D parameter, 3-15 DOLBY D STATUS menu, 2-16 DOLBY DIGITAL EX listening mode, 5-19 DOLBY DIGITAL listening mode, 5-19 DOLBY PL + THX listening mode, 5-8 DOLBY PLII + THX listening mode, 5-7 DOLBY PLII MOVIE listening mode, 5-6 DOLBY PLII MUSIC listening mode, 5-6 DOLBY PRO LOGIC listening mode, 5-7 dts button, 2-13 DTS NEO:6 + THX listening mode, 5-9 DTS NEO:6 CIN listening mode, 2-13, 5-8 DTS NEO:6 MUSIC listening mode, 5-9 DTS THX MUSIC listening mode, 5-26 DTS THX ULTRA2 lis
Index AV1 MUTE ON message, 2-3 N NAME parameter, 3-4 NIGHTCLUB listening mode, 5-10 O Off button, 2-10 On button, 2-10 ON-SCREEN DISPLAY menu, 3-47 operation considerations, 2-6 OSD button, 2-10 output connectors audio, 2-5 trigger, 2-5 video, 2-5 OUTPUT LEVELS parameter, 5-33 output levels, calibrating, 3-37 P PANORAMA Calibration, 5-12 PANORAMA listening mode, 5-12 PANORAMA parameter, 5-34 parameter drop-down menus, 2-8 parameters listening mode menu, 5-29 preferred listening mode selection, 3-13 sele
Index two-line status, 2-14 U UNITS parameter, 3-36 USE LAST setting, 3-14 V VCR button, 2-12 VIDEO IN parameter, 3-11 video input connectors, 2-5 video output connectors, 2-5 VOCAL ENHANCE parameter, 5-36 Vol button, 2-11 VOLUME CONTROL SETUP menu, 3-2, 3-51 Volume knob, 2-3 W WORD LENGTH parameter, 2-20 I-4 JBL Performance
JBL PERFORMANCE LIMITED WARRANTY Performance Limited Warranty The JBL Performance products listed below are warranted for the period stated from the date of original purchase: Amplifiers, Equalizers, and Surround Sound Processors – two (2) year warranty. Who is protected by this warranty? Your JBL warranty protects the original owner and all subsequent owners, so long as the original bill of sale is presented when warranty service is requested.
JBL Performance 8500 Balboa Boulevard Northridge, CA 91329 250 Crossways Park Drive Woodbury, NY 11797 800-336-4JBL Part No.