CS6100-120V om.
CS6100-120V om.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 5 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 6 THANK YOU FOR CHOOSING JBL PLANNING YOUR SYSTEM For more than 60 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. Before deciding where to best place your speakers, survey your room and study Figures 1 and 2.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 7 PLACEMENT Left and Right Front Channels For left and right front channels, place one satellite to the left and another to the right of the television, as shown in Figure 1. Since the speakers are magnetically shielded, you can place them very close to the TV without worrying about the magnetic field distorting the picture. Center Channel For the center channel, place the speaker directly on top of, or below, your television.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 8 WALL - MOUNTING THE SATELLITES AND CENTER CHANNEL The CS6100 satellites and center channel are designed to be mounted on the wall. There is a fixed-mount wall bracket and an adjustable wall bracket provided for each satellite and the center channel. Each speaker bracket will require up to four 1-1/2" #10 wood screws; each screw should be fastened to a wall stud. If a wall stud is unavailable, install an anchor appropriate for a 1-1/2" #10 screw.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 9 CENTER AND SATELLITE SPEAKER CONNECTIONS Turn Off All Power After placing the speakers, you are ready to connect your system. First, turn off all audio-system power. Use high-quality speaker wire to make your connections (#18-gauge speaker wire with polarity coding is included). For longer distances, #16-gauge or heavier wire is recommended. The side of the wire with a ridge or other coding is usually considered positive (+) polarity.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 10 SUBWOOFER CONTROLS Rear Panel Subwoofer Connections If you have a Dolby® Digital or DTS® receiver/processor with a low-frequency-effects (LFE) or subwoofer output: RECEIVER/PROCESSOR SUBWOOFER OR LFE OUTPUT 15' (4.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 11 OPERATION Surround Modes When using the CS6100 speakers in a Dolby Digital or DTS home theater system, make sure all speakers are set to “Small”. In a Dolby Pro Logic® home theater system, make sure the receiver’s center channel mode is set to “Normal.” Some Dolby Digital-equipped receivers/processors offer different setup options for each source or surround mode (e.g., CD-stereo, videotape, Dolby, Pro Logic).
CS6100-120V om.qxd 12/15/06 4:26 PM Page 12 SPECIFICATIONS CS6100 SATELLITES Frequency Response (– 6dB): 100Hz – 20kHz Recommended Amplifier Power Range: 10 – 100 Watts Sensitivity (2.83V @ 1 meter): 88dB Nominal Impedance: 8 Ohms Crossover Frequency: 3.
CS6100-120V om.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 2 All features and specifications are subject to change without notice. JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries. Pro Sound Comes Home is a trademark of Harman International Industries, Incorporated. Dolby and Pro Logic are registered trademarks of Dolby Laboratories. DTS is a registered trademark of DTS, Inc. PRO SOUND COMES HOME™ ® Harman Consumer Group, Inc.
