USER’S GUIDE For: Français, Deutsch, Español, visit www.jblpro.
Contents Section 1: Important Safety Instructions ���������������������������������������������������������� 1 Care & Cleaning ��������������������������������������������������������������������������������������������������������������������������������������������������2 Section 2: Precautions ���������������������������������������������������������������������������������������� 3 Section 3: EON ONE PRO System Declaration of Conformity ������������������������ 4 Section 4: Introduction to the EON ONE
Section 1: Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
CARE & CLEANING EON ONE PRO systems may be cleaned with a dry cloth. Do not get moisture into any of the openings in the system. Ensure that the system is unplugged from the AC outlet before cleaning. THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES. TO PREVENT ELECTRIC SHOCK OR HAZARD, DO NOT REMOVE CHASSIS, MIXER MODULE, OR AC INPUT COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Section 2: Precautions ! The EON ONE PRO system covered by this manual is not intended for use in high moisture environments. Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts. Avoid exposing the speakers to direct moisture. Keep speakers out of extended or intense direct sunlight. The driver suspension will prematurely dry out and finished surfaces may be degraded by long-term exposure to intense ultra-violet (UV) light.
Section 3: EON ONE PRO System Declaration of Conformity This equipment complies with the EMC directive 89/336/EEC Modified by 92/31/EEC 93/68/EEC 98/13/EEC and LVD 73/23/EEC modified by 93/68/EEC This product meets safety standards: EN60065:2002 UL6500 7th Edition: 2003 UL 60065 - STANDARD FOR AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY EQUIREMENTS - Edition 7 - Revision Date 2007/12/11 CSA C22.
Section 4: Introduction to the EON ONE PRO System Thank you for choosing the JBL EON ONE PRO system. The EON ONE PRO is a portable all-in-one linear-array system featuring rechargeable battery power, multiple input channels with individual tone controls, reverb, and Bluetooth® audio streaming.
4. Connect the female end of the power cable to the EON ONE PRO and plug the male end into a wall socket. Ensure the Power switch is turned off and the power LED is not lit. If using the unit's battery power feature, allow the unit to charge. The Battery Level meter will illuminate, indicating the unit is charging. The lithiumion battery will take approximately 5 hours to fully charge, and the Battery Level meter will fully illuminate to indicate charging is complete.
7. Turn the POWER switch to the “on” position. The POWER LED indicators on the front and back of the unit will illuminate to indicate power is turned on. Power Switch 8. If connecting a Bluetooth device for audio streaming, follow these steps: a. Enable Bluetooth on your source device. b. Press the BLUETOOTH button. c. Find JBL EON ONE PRO on your device and select it. d. If applicable, connect the device to the USB POWER port to keep it charged. Bluetooth Button 9.
PA BASICS A mixing board is actually a very simple device that takes the audio input signals (from the input channels) and "mixes" them to the outputs. The mixing board controls will typically enable the user to blend the input channel signal levels, affect their tone, and adjust each channel's reverb level. The signal is then fed from the mixing board to the amplifiers and on to the speakers. The EON ONE PRO is a self-contained PA system, which includes a mixing board, amplifiers, and speakers.
AUDIO INPUTS The EON ONE PRO has 7 inputs: 4 mono inputs, a 2-channel (stereo) input, and a Bluetooth audio streaming input. All of the inputs will route to the speakers, the MONITOR OUT jack, and the PASS THRU out jack. MONO MIC/LINE INPUTS Moving from left to right there are four identical input strips comprised of (from top to bottom) a treble control, bass control, reverb control, reverb on/off button, mic/line selector, volume control, and a XLR / 1/4" combination input connector.
PHANTOM POWER DISCLAIMER When using condenser microphones, +48V phantom power is required to be present at the contacts of the microphone (XLR) connector for the microphone to operate correctly. When phantom power is enabled, it is applied to both the CH1 and CH2 XLR inputs. Ensure that phantom power is off when not required.
STEREO INPUTS The CH 5/6 stereo inputs are intended to be used primarily for MP3 or other personal music players and offer the option of using RCA plugs or a 3.5 mm stereo connector plug (the type typically found on personal music players). The CH 5/6 control is used to control volume for this stereo input. Volume control for the CH 5/6 stereo input Stereo in 5/6 RCA inputs for use with personal music player or any consumer-type electronics CH 5/6 3.
AUDIO OUTPUTS Monitor Out connectors with volume control are used to route the stereo mixer signal to another destination, such as a recording device, powered personal monitor, or another PA system PASS THRU output can be connected to the XLR input of another JBL EON ONE PRO to expand the system for higher output capabilities USB POWER PORT This port can be used to charge a Bluetooth device or other portable music playback device during use.
Section 5: Accessories WHEELED BAG The optional wheeled bag is available for effortless transport of an EON ONE PRO system. Visit jblpro.com or contact your local JBL Pro dealer for more information.
Section 6: System Specifications System Battery Amplifier Mixer System Type: Battery-operated portable line array with powered mixer Maximum SPL Output: 118 dB peak system output (pink noise) Frequency Range (-10dB): 37.5Hz – 18.
Section 7: Cables & Connectors XLR/F to XLR/M microphone cable The standard cable for interconnection of microphone and linelevel signals in professional audio systems. Example: Microphone to mixer. TRS (balanced) 1/4" phone to XLR/M cable For connecting balanced devices with 1/4" phone; may be used interchangeably. TRS (unbalanced) 1/4" phone to XLR/M cable For connecting instruments with unbalanced outputs to balanced XLR inputs.
Section 8: Contact Information Mailing Address: JBL Professional 8500 Balboa Blvd. Northridge, CA 91329 Shipping Address: JBL Professional 8500 Balboa Blvd., Dock 15 Northridge, CA 91329 (Do not return product to this address without first obtaining prior authorization from JBL) Customer Service: Monday through Friday 8:00am - 5:00pm Pacific Coast Time in the U.S.A. (800) 8JBLPRO (800.852.5776) www.jblproservice.com On The World Wide Web: www.jblpro.
Section 9: Warranty Information The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the date of original purchase. Enclosures and all other JBL products are warranted for two years from the date of original purchase. Who Is Protected By This Warranty? Your JBL Warranty protects the original owner and all subsequent owners so long as: A.
Rev C
