Owner`s manual

English
7
SPECIFICATIONS ES150PW ES250PW
Frequency Response 27Hz – 150Hz 25Hz – 150Hz
Amplifier RMS Power 300 Watts 400 Watts
Amplifier Peak Dynamic Power
†
500 Watts 700 Watts
Crossover Frequency 50Hz – 150Hz; 24dB/octave 50Hz – 150Hz; 24dB/octave
continuously ajustable continuously ajustable
when activated when activated
Driver 250mm (10") PolyPlas
™
300mm (12") PolyPlas
™
Operating Range Up to 22m (75'), Up to 22m (75'),
depending upon conditions depending upon conditions
RF Operating Frequency 2.4GHz 2.4GHz
Subwoofer Dimensions 457mm x 337mm x 409mm 502mm x 400mm x 454mm
(H x W x D) (18" x 13-1/4" x 16-1/8") (19-3/4" x 15-3/4" x 17-7/8")
Transmitter Dimensions 95mm x 124mm x 100mm 95mm x 124mm x 100mm
(H x W x D) (3-3/4" x 4-7/8" x 3-15/16") (3-3/4" x 4-7/8" x 3-15/16")
Subwoofer Weight 17.7kg (39 lb) 19.5kg (43 lb)
Transmitter Weight 0.2kg (0.5 lb) 0.2kg (0.5 lb)
†
The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to
minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product
described in this ownerʼs manual is in compliance
with technical standards:
EN 55013:2001+A1:2003
EN 55020:2002+A1:2003
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:2001
EN 60065:2002
Laurent Rault
Harman Consumer Group, Inc.
Château du Loir, France 6/08
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product
described in this ownerʼs manual is in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group, Inc.
Château du Loir, France 6/08
struction methods and materials, atmospheric conditions and other
sources of interference. Please consult your JBL dealer or distribu-
tor, or visit www.jbl.com, for further information or assistance.
Wall-Mounting the Transmitter Module
NOTE: The customer is responsible for the correct selection and use
of mounting hardware (available through hardware stores) that will
ensure the proper and safe wall-mounting of the transmitter.
1. Insert the two M3 x 4 machine
screws through the wall bracket
and into the rear of the transmitter
module, as shown.
2. Attach the transmitter module with
wall bracket to the wall, using suit-
able hardware and, if necessary,
wall anchors.
MAINTENANCE AND SERVICE
The enclosure may be cleaned using a soft cloth to remove finger-
prints or to wipe off dust.
The grille may be gently vacuumed. Stains may be removed with an
aerosol cleaner, following its instructions. Do not use any solvents
on the grille.
All wiring connections should be inspected and cleaned or remade
periodically. The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions and other
factors, but once per year is the minimum.
In the event that your subwoofer ever needs service, contact your
local JBL dealer, or visit www.jbl.com for a service center near you.
0048CSK - JBL ES150PW_ES250PW ENG v2.qxp:33346_JBL ES150_250_ENG 30/07/08 6:47 Side 7 (Sort/Black plade)