P-Series Owner's Manual 5/25/99 9:46 AM Page 1 Automotive Loudspeakers P -4 3 2, P- 5 32 , P -63 2 , P -9 6 32 , P- 96 3 3, P - 33 2, P- 6 4 32 , P- 7 5 32 , P -23 t & P-K it Ow n er ’s M a nu al GE NU I NE J BL
P-Series Owner's Manual 5/25/99 9:46 AM Thank you for purchasing JBL's Power Series™ automotive loudspeakers. In order that we may better serve you should you require warranty service on your new speakers, please retain your original purchase receipt and return the enclosed warranty registration card. Important: Installation of automotive stereo components can require extensive experience performing a variety of mechanical and electrical procedures.
P-Series Owner's Manual 5/25/99 9:46 AM Page 3 Installation of the P-332, P-6432 and P-7532, as shown in Figure 1. Figure 1. Note: The P-332, P-6432 and P-7532 are designed as direct replacements for original-equipment speakers mounted behind factory grilles. Installation of the P-432, P-532, P-9632 and P-9633, as shown in Figures 2 and 3. Figure 2. Note: If you are mounting the P-532, P-9632 or P-9633 behind factory grilles, omit the grille and grille tray in Figure 2. Figure 3.
P-Series Owner's Manual 5/25/99 9:46 AM Page 4 Installation of the P-632, as shown in Figures 4a and 4b. The P-632 uses JBL's Intermount III™ mounting system. Intermount III™ provides for easy installation of these speakers in many standard and nonstandard locations that will accommodate a 6-1/2" speaker. Figure 4a. Using Intermount III™ in American and Japanese cars with openings for 6-1/2" speakers.
P-Series Owner's Manual 5/25/99 9:46 AM Page 5 Converting the P-432, P-532 and P-632 to a component system using the optional P-Kit (sold separately), as shown on pages 5 and 6. Separating the tweeter and woofer, as shown in Figures 5a and 5b. Figure 5a. Remove the orange wire cover by inserting a small screwdriver into the notch between the two terminals and prying upwards. Disconnect the tweeter wires from the terminal. Reinstall the cover after removing the tweeter. Figure 5b.
P-Series Owner's Manual 5/25/99 9:46 AM Page 6 Mounting the tweeter (P-23t), as shown in Figures 6a and 6b. The tweeter may be either surface-mounted or flush-mounted with parts supplied in the P-Kit. Connecting the woofer and tweeter to the passive crossover, as shown in Figures 7a and 7b. Figure 7a. Figure 6a. Figure 7b. Position the "Lo Pass" and "Twt Frq" according to the speaker you are using as shown in the callouts in Figure 7b. Surface-mounting the P-23t.
P-Series Owner's Manual 5/25/99 9:46 AM Page 7 Specifications Woofer-Cone Material Tweeter-Diaphragm Material Frequency Response Sensitivity Recommended Amplifier Power Range as Multielement Recommended Amplifier Power Range as Component Mounting Depth Woofer-Cone Material Tweeter-Diaphragm Material Frequency Response Sensitivity Recommended Amplifier Power Range as Multielement Recommended Amplifier Power Range as Component Mounting Depth P-432 P-532 P-632 P-9632 P-9633 4" 2-Way or Component Sy
P-Series Owner's Manual 5/25/99 9:46 AM Page 8 Declaration of Conformity We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992 Steen Michaelsen JBL Europe A/S Birkerød. DENMARK. 3/99 JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 800-336-4JBL (4525) www.jbl.com Part No.