P User’s Guide P R X 5 1 2 M P R X 5 1 5 P R X 5 3 5 P R X 5 2 5 R X 5 1 8 S
CONTENTS Important Safety Instructions 4 Precautions 5 The PRX500 Series Power Amplifier 8-9 Introduction To The PRX500 Series 10 System Specifications 11 - 15 System Setup 16 - 19 Setting Input Sensitivity 20 Setting The Gain 21 Application Examples 22 - 25 Reference 26 Cables and Connectors 27 Troubleshooting 28 - 29 Contact Information 30 Warranty Information 31 3
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
PRECAUTIONS The PRX500 series speakers covered by this manual are not intended for fixed installation and high moisture environments. Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts. Avoid exposing the speakers to direct moisture. Keep speakers out of extended or intense direct sunlight. The driver suspension will prematurely dry out and finished surfaces may be degraded by long-term exposure to intense ultra-violet (UV) light.
WATCH FOR THESE SYMBOLS! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated." "Dangerous Voltage" within the products enclosure that may be of sufficient magnitude to consitute a risk of electric shock to persons. 6 ! WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
PRX500 Series speakers Declaration of Conformity Safety And EMC Compliance Specifications EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions EN 55103-1:1997 Magnetic Field Emissions-Annex A @ 10 cm and 20 cm EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits; Conducted, Class A EN 55103-2:1997 Electromagnet
The PRX500 Series power amplifier AC Power Requirements Standard PRX500 series speaker systems are equipped with a multi-channe Crown Class-D power amplifier and loudspeaker specific DSP electronics and require appropriate AC power. Before plugging a PRX500 speaker into an outlet ensure that it is able to provide the appropriate AC power as set on the speaker. A robust AC supply is necessary for maximum performance.
Operating Temperature The design of the Crown amplifier is such that it is very energy efficient and as a result does not get really hot. In the rare event that it does get too hot it will automatically shut down to protect itself. When its temperature has returned to within its operating range it will turn back on. A Condition under which this may occur is when the system is operated in very high ambient temperatures and the heat sink on the rear of the enclosure is in direct sunlight.
Introduction to the PRX500 series PRX512M PRX518S PRX515 PRX525 PRX535 Thank you for choosing the JBL PRX500 series self-powered PA loudspeakers. There are five models in the series, four full-range systems and one subwoofer. All are powered by integrated digital power amplifiers developed by Crown, the most trusted name in professional sound reinforcement power amplification.
SYSTEM SPECIFICATIONS PRX512M System Type: Self powered 12", two-way, bass-reflex Frequency Range (-10 dB): 46Hz - 20kHz (EQ in main position) 60Hz - 20kHz (EQ in monitor position) Frequency Response (±3 dB): 76Hz - 20kHz (EQ in main position) 90Hz - 20kHz (EQ in monitor position) Coverage Pattern: 70º x 70º nominal Directivity Index (DI): 10.2 dB Directivity Factor (Q): 10.8 Crossover Modes: DSP controlled 48dB filter slope Crossover Frequency: 1.
PRX515 System Type: Self powered 15", two-way, bass-reflex Frequency Range (-10 dB): 45Hz - 20kHz (EQ in flat position) Frequency Response (±3 dB): 52Hz - 20kHz (EQ in flat position) Coverage Pattern: 70º x 70º nominal Directivity Index (DI): 10.3 dB Directivity Factor (Q): 10.8 Crossover Modes: DSP controlled 48dB filter slope Crossover Frequency: 1.
PRX525 System Type: Self powered dual 15", two-way, bass-reflex Frequency Range (-10 dB): 40Hz - 20kHz (EQ in flat position) Frequency Response (±3 dB): 52Hz - 20kHz (EQ in flat position) Coverage Pattern: 70º x 70º nominal Directivity Index (DI): 10.3 dB Directivity Factor (Q): 10.8 Crossover Modes: DSP controlled 48dB filter slope Crossover Frequency: 1.
PRX535 System Type: Self powered 15", three-way, bass-reflex Frequency Range (-10 dB): 39Hz - 20kHz (EQ in flat position) Frequency Response (±3 dB): 46Hz - 20kHz (EQ in flat position) Coverage Pattern: 90º x 50º nominal Directivity Index (DI): 10.6 dB Directivity Factor (Q): 11.4 Crossover Modes: DSP controlled 24dB filter slope Crossover Frequency: 430 Hz, 2.
PRX518S System Type: Self powered 18", bass-reflex Frequency Range (-10 dB): 37Hz - 140Hz Frequency Response (±3 dB): 52Hz – 110Hz Crossover Modes: DSP controlled 48dB filter slope Crossover Frequency: 110Hz System Power Rating: 500 W continuous, 1000W peak LF Power amp: Class-D, 500 Watt (continuous) at driver impedance Distortion: Less than 0.
SYSTEM SET UP - FULL RANGE MODELS PRX500 Amplifier Input Configuration for PRX512M, PRX515, PRX525 And PRX535 Full-Range Models: 1 2 EQ INPUT BOOST MIC 3 4 LEVEL -10 dB +4 dB FLAT 9 5 OVERLOAD PRX515 SIGNAL l 6 LINE SELECT 7 IN JBL PROFESSIONAL Northridge, CA. USA AC LINE INPUT Equipped with Differential Drive® Transducer Technology U.S. PATENT 5,748,760 Other U.S.
2 - INPUT MIC / LINE: Allows the selection of different input sensitivities to permit the connection of many different sources, with or without the use of a mixer or external microphone preamplifier. See “Setting Input Sensitivity” on page 18. 3 - LEVEL: Sound level adjustment. With the input in the “MIC” position the level can be adjusted over a large range. In the “LINE” position most typical applications will require that the level control is set at 12 o’clock.
SYSTEM SET UP - SUBWOOFER PRX500 Amplifier Input Configuration for PRX518S Subwoofer Model: 1 2 3 4 XOVER POLARITY IN 0 LEVEL 5 OVERLOAD PRX518S SIGNAL l POWER 180 OUT 6 LINE SELECT 9 IN 7 JBL PROFESSIONAL Northridge, CA. USA AC LINE INPUT RIGHT LEFT CSA Certification applies to Amplifier Module Only 100V~ -240V~ 50/60 Hz 5A 600W CSA Certificated to operate at 120V~ in Canada 10 8 OUT N 108 Designed, Engineered and Assembled in U.S.A.
3 - LEVEL: Sound level adjustment. The 12 o’clock position is a good starting point for most usages. Once the full-range system has been connected the level can be varied to match and deliver the desired balance (for details see Setting the Gain on page 21). 6 - POWER SWITCH: Turns the power on. Power “on” status is indicated with the illumination of the logo on the grille. 7 - LINE SELECT: Allows the user selection for different local voltage ratings.
SETTING THE INPUT SENSITIVITY PRX500 series systems have been designed to allow the connection of a variety of sources. This provides a great deal of versatility, especially with the PRX512M and PRX515, as a microphone or instrument can be connected directly to the input. Low levels output from consumer products like MP3 and CD players, can also be accommodated. There are two user selectable gain or input sensitivity ranges: Mic and Line.
The following levels should be used as a reference if you know the maximum output in dBu of the source connected to the system’s input. For each position stated below there is an input signal level in dBu that is required to deliver absolute maximum output of the system.
APPLICATION EXAMPLES Basic Sound Reinforcement System This is a very basic sound system. PRX500 series speakers allow the direct connection of sound sources, without the need for extra mixer or pre-amplifier. The XLR or 1/4 inch input jack provides versatility and cabling options and the mic/line input sensitivity selector switch optimizes the speaker gain for the input source. Additional speakers may be connected (daisy chained together) in mono mode.
Music Playback Reinforcement With Subwoofer (PRX512M Pole Mounted On A PRX518S) This is a very powerful, but flexible combination. The subwoofer provides the extra low frequency extension and also serves as the base for the pole mount. The compact 12 inch satellite system, PRX512M is a perfect match to the subwoofer. From the master outputs of your mixer route the wires to the subwoofer first and select the x-over in (high-pass) option. Route the cable form the subwoofer output connector to the top.
Live Performance Or Music Playback Reinforcement System With Stage Monitors (PRX535 And PRX512M) This is an ideal system when wide coverage and good directivity is required, specifically in highly reverberant rooms. The horn loaded PRX535 3-way system will control the propagation of the sound much better than a conventional 2-way system. The more directional or controlled the sound is the more independent the system becomes from the room acoustics present, resulting in a much clearer sound.
Large Live Performance Or Music Playback Reinforcement System With Stage Monitor (4 x PRX518S, 4 x PRX525 And 2 x PRX512M) For larger crowds in and outdoors, a flexible system like this will deliver excellent results. The dual 15 inch PRX525 delivers mighty bottom end and crisp highs. The combination of extra PRX518S subwoofers gives it a even more thunderous low end. The PRX525’s can be arrayed as pair of two’s each side for a wider coverage and some extra SPL (extremely useful in outdoor applications).
REFERENCE Balanced vs. Unbalanced Lines Your PRX500 series can accept either type of input. There are two basic types of audio system interconnections for audio signals: Balanced and Unbalanced. Balanced Lines In audio, a balanced line is a three-conductor system in which the two signal wires carry an equal, but opposite voltage with respect to the ground wire. The ground wire acts only as a shield and does not carry any audio signal current.
CABLES AND CONNECTORS XLR/F to XLR/M Microphone Cable The standard cable for interconnection of microphone and line level signal in professional audio systems. • Microphone to mixer • Microphone to PRX500 direct input • Professional audio mixer to PRX500 • Daisy chaining PRX500 speakers TRS (balanced) 1/4 inch phone jack to XLR/M For connecting balanced devices with 1/4 inch phone and maybe used interchangeably.
TROUBLESHOOTING Symptom Likely Cause No sound. Speaker not connected to active AC power. Verify that speaker is connected and that the circuit is on. Switch on power and verify that illuminated logo is on. Speaker power Cable is faulty or improperly Connected. • Re-seat the power cable at both ends. • Substitute a known-good power cable. Blown fuse. • Replace the fuse with the specified value. • Take your speaker to a competent servicer.
Noise or hiss heard at output Noisy Source Device Disconnect the devices that are connected to your speaker one at a time. If the noise goes away, the problem is with the source or the connecting cable. Hum or Buzz that increases or decreases when the mixer level controls are moved. Improper A/C ground or faulty equipment connect to mixer input Disconnect or mute channels one at a time to isolate the problem. Refer to the owner’s manual of the faulty equipment for troubleshooting help.
CONTACT INFORMATION Mailing Address: JBL Professional 8500 Balboa Blvd. Northridge, CA 91329 Shipping Address: JBL Professional 8370 Balboa Blvd., Dock D Northridge, CA 91329 (Do not return product to this address without first obtaining prior authorization from JBL) Customer Service: Monday through Friday 8:00am -5:00pm Pacific Coast Time In the U.S.A. (800)8JBLPRO (800.852.5776) www.jblproservice.com On The World Wide Web: www.jblpro.
WARRANTY INFORMATION The JBL Limited Warranty on professional loudspeaker products (except for enclosures)remains in effect for five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the date of original purchase. Enclosures and all other JBL products are warranted for two years from the date of original purchase. Who Is Protected By This Warranty? Your JBL Warranty protects the original owner and all subsequent owners so long as: A.
Part Number: 363264-002 8/2008 8500 Balboa Boulevard Northridge, CA 91329 USA Visit us online at www.jblpro.