The SCS200.6 system is shown here. ® SURROUND CINEMA SPEAKERS SCS200.5/230 and SCS200.
READ FIRST! Important Safety Precautions! 1. Unpacking: Check the product carefully. If it has been damaged in transit, report the damage immediately by calling your dealer and/or the shipping company that delivered it. 2. Connections: Whenever changing, connecting or disconnecting signal or power cables etc., always turn off all equipment. This prevents transients from entering the equipment and prevents electrical energy from reaching you. Keep all connections out of the reach of children.
antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 18. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
THANK YOU FOR CHOOSING JBL For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident that the JBL system you have chosen will provide every note of enjoy- ment that you expected – and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL.
SPEAKER PLACEMENT FRONT SPEAKERS CENTER CHANNEL SPEAKER SUBWOOFER 0-0.6m 0-2 ft SURROUND SPEAKERS † 1.5 – 1.8m 5 – 6 ft † Alternate placement for surround speakers in SCS200.5 system only. † The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners’ ears will be, or they may be angled toward the listeners.
MOUNTING OPTIONS SATELLITES AND SURROUNDS On shelves. On the wall. Wall brackets are included. On optional stands. ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as described on page 8. Thread the two conductors through the two holes in the stand bracket. Make sure to preserve the proper polarity (+ and – connections) by threading the positive conductor through the hole on + – 6 the left, and the negative conductor through the hole on the right looking at the front of the stand.
WALL-MOUNTING Step 5: Tighten the Metal Nut ¡ with the star washer side between the Metal Nut ¡ 4 3 2 and the back of the Satellite Speaker ¶, using large needle-nose pliers until it is firmly seated against the back of the Speaker ¶ and has locked the Ball and Shaft £ and the Speaker ¶ together. Note that once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. However, these marks will be covered by the Metal Nut ¡.
Speaker ¶ as described in Step 5 before beginning Step 7 in order to avoid damage to the Threaded Insert §. Such damage would not be covered under the warranty. Step 7: Holding the Satellite Speaker ¶ with both hands, reinsert the ball portion of the Ball and Shaft £ into the Attachment Plate ¢. Step 8: Hand-tighten the Molded Nut ™ while positioning the speaker for the desired orientation.
DOLBY* DIGITAL OR DTS® (OR OTHER DIGITAL SURROUND MODE) CONNECTION RECEIVER LINE LFE LEVEL IN LFE OUT output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. SUBWOOFER L R Use this installation method for Dolby* Digital, DTS® or other digital surround processors: Make sure that you have configured your surround sound processor for “Subwoofer On”. For the SCS200.
DOLBY PRO LOGIC (NON-DIGITAL) – SPEAKER LEVEL Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor does not have a subwoofer output, or a volumecontrolled preamp (line-) level output: Left Front – + – – + + Subwoofer Connect your receiver or amplifier’s front left and right speaker terminals to the left and right terminals on the subwoofer that are marked “Speaker Level In.
OPERATION Move the Master Power switch (marked “Power” å) to the “•” (On) position to use the SUB200 subwoofer. ∫ If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power switch å to the Off position. å VOLUME Subwoofer Level MIN Volume may be adjusted using the Subwoofer Level control ∫ as shown.
TROUBLESHOOTING If there is no sound from any of the speakers: • Check that receiver/amplifier is on and a source is playing. • Check that the powered subwoofer is plugged in, and its Power switch å is switched on (“•” position). • Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. • Review proper operation of your receiver/amplifier.
If there is no sound from the surround speakers: • Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. • Review proper operation of your receiver/amplifier and its surround sound features. • Make sure the movie or TV show you are watching is recorded in a surround sound mode.
SPECIFICATIONS SCS200.5/230 AND SCS200.6/230 SYSTEMS Frequency Response 35Hz – 20kHz (–6dB) SATELLITES Maximum Recommended Amplifier Power 100 Watts Power Handling (Continuous/Peak) 50W/160W Nominal Impedance 8 Ohms Sensitivity 86dB @ 1 Watt/1 meter Frequency Response 110Hz – 20kHz (–6dB) Tweeter One 13mm (1/2") titanium-laminate dome, video-shielded Midrange One 75mm (3") driver, video-shielded Dimensions (H x W x D) (not including shelf stands) 184 x 102 x 89mm (7-1/4" x 4" x 3-1/2") Weight 0.8kg (1.
