SYNTHESIS SDP-40 DIGITAL SURROUND PROCESSOR/CONTROLLER USER GUIDE
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus, (including amplifiers) that produce heat.
DOCUMENTATION CONVENTIONS This document contains general safety, installation, and operating instructions for the SDP-40 Digital Surround Processor/ Controller. It is important to read this user guide before attempting to use this product. Pay particular attention to safety instructions. The following symbols are used in this document: WARNING Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in injury or death.
Introduction Introduction JBL Section 1: Getting Started About the SDP-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Highlights US Important Safety Instructions . . . . . . . . . . . . . . . . . . iv DE Wichtige Sicherheitsanweisungen . . . . . . . . . . . . . . . . . iv Installation Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 ES Instrucciones importantes de seguridad . . . . . . . . . . . . . v Remote Control Battery Installation . . . . . .
Introduction SDP-40 Section 3: SETUP Section 6: Troubleshooting & Maintenance (continued) TRIGGER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-48 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 LOCK OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Restoring Factory-Default Settings . . . . . . . . . . . . . . . . . . .
Introduction US JBL ENGLISH IMPORTANT SAFETY INSTRUCTIONS US Save these instructions for later use. • Follow all instructions and warnings marked on the unit. • Always use with the correct line voltage. Refer to the manufacturer’s operating instructions for the power requirements. Be advised that different operating voltages require the use of a different line cord and/or attachment plug.
Introduction SDP-40 ES ESPAÑOL INSTRUCCIONES IMPORTANTES DE SEGURIDAD ES Guarde esta instrucciones para uso posterior. • Utilice siempre el voltaje correcto. Diríjase a las instrucciones de operación del fabricante para obtener las especificaciones de potencia. Esté al tanto de que voltajes de operación distintos requieren el uso de cables y/o enchufes distintos.
Introduction IT JBL ITALIANO IMPORTANTI NORME DI SICUREZZA IT Conservare le presenti norme per l’utilizzo futuro. • Osservare tutte le istruzioni e le avvertenze apposte sull’unità. • Utilizzare esclusivamente con la tensione di rete corretta. Consultare le istruzioni operative fornite dal fabbricante per i dati riguardanti la tensione e l’assorbimento di corrente. Potrebbe essere necessario l’uso di cavi di rete e/o di spine diverse a seconda della tensione utilizzata.
Introduction SDP-40 DK DANSK VIGTIG INFORMATION OM SIKKERHED DK Gem denne vejledning til senere brug. • Følg alle anvisninger og advarsler på apparatet. • Apparatet skal altid tilsluttes den korrekte spænding. Der henvises til brugsanvisningen, der indeholder specifikationer for strømforsyning. Der gøres opmærksom på, at ved varierende driftsspændinger kan det blive nødvendigt at bruge andre lednings- og/eller stiktyper.
Introduction NO NORSK VIKTIG INFORMASJON OM SIKKERHET JBL NO Ta vare på denne veiledningen for senere bruk. • Følg alle anvisningene og advarslene som er angitt på apparatet. • Apparatet skal alltid anvendes med korrekt spenning. Produktbeskrivelsen inneholder spesifikasjoner for strømkrav. Vær oppmerksom på at det ved ulike driftsspenninger kan være nødvendig å bruke en annen ledning- og/eller støpseltype.
Introduction SDP-40 US Unpacking and Inspection After unpacking the unit, save all packing materials in case the unit ever needs to be shipped. Thoroughly inspect the modules and packing materials for signs of damage. Report any damage to the carrier at once; report equipment malfunction to the dealer. DE Contenu de l’emballage et inspection Après avoir ouvert l’emballage, conservez-le pour tout retour. Inspectez avec soin les modules et les matériaux d’emballage pour tout signe de dommage.
1 Getting Started About the SDP-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Highlights • Product Registration Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Do • Do Not Remote Control Battery Installation . . . . . . . . . . . . . . . . . . . . . . .
Getting Started ABOUT THE SDP-40 Thank you for purchasing the SDP-40 Digital Controller, a referencequality, 12-channel audio and video control center with independent zone monitoring to provide control of input source selection in three zones at the same time. As flexible as it is powerful, the SDP-40 includes 12 configurable inputs, each of which can be assigned to its 13 digital audio, 8 analog audio, 5 composite video, 8 S-video, or 4 component video input connectors.
Getting Started SDP-40 Complementing its pristine audio performance, the SDP-40 includes two broadcast-quality video switchers. An ultra-wide bandwidth component video switcher accepts analog component or RGB video signals, while a composite and S-video switcher accepts high-quality NTSC, PAL, or SECAM video signals. The component video switcher can pass High-Definition TV (HDTV) and Standard-Definition TV signals. Both switchers are designed to pass video signals without alteration or degradation.
Getting Started JBL DO NOT INSTALLATION CONSIDERATIONS The SDP-40 requires special care during installation to ensure optimal performance. Pay particular attention to the bulleted items that begin below and to other precautions that appear throughout this user guide. DO • • Install the SDP-40 on a solid, flat, level surface such as a table , shelf, or in a standard 19-inch equipment rack using the enclosed rack-mount kit. Select a dry, well-ventilated location out of direct sunlight.
Getting Started SDP-40 REMOTE CONTROL BATTERY INSTALLATION The remote control requires two AA batteries that should be replaced as needed. It is recommended to use Alkaline batteries, which last longer without leaking. When the batteries are low on power, the remote control enters a low-voltage condition that prevents it from operating the SDP-40. When this occurs, follow the instructions below to replace the batteries. Normal operation will resume when new batteries are installed.
2 Basic Operation Front Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Operation Considerations • MAIN MENU • Menu Navigation • Menu Item Selection • Command Bank Activation • Command Matrix Understanding the Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operation JBL FRONT PANEL OVERVIEW 2 4 1 3 6 IR Receiver Red LED Blue LED 2-2 5 Amber LED 7 11 9 8 10 12
Basic Operation SDP-40 1. Standby Button Activates and deactivates standby mode when the SDP-40 is powered on with the rear panel power switch. The standby button performs no function when the SDP-40 is powered off with the rear panel power switch. When standby mode is activated, pressing the standby button deactivates standby mode and activates the SDP-40 including all zones that were activated during the previous operating session.
Basic Operation JBL Front Panel Overview (continued from page 2-3) ZONE2 VOLUME -34dB The amber Mute button LED lights whenever mute is activated, whether activated automatically or manually. For instance, the SDP-40 briefly activates mute when changing input sources or listening modes. To use the volume knob to adjust Main Zone volume level: 1. Rotate the volume knob clockwise to increase or counterclockwise to decrease volume level in 1dB increments.
Basic Operation SDP-40 8. Main Zone Off Button Deactivates the Main Zone. 9. Zone 2 Input Selection Buttons Selects the input in Zone 2. When an input is selected, an amber LED lights on the corresponding input selection button. When Zone 2 is deactivated, pressing a Zone 2 input selection button activates Zone 2 and selects the corresponding input. The Main and Record Zones remain deactivated until a Main or Record Zone input is selected. REAR PANEL OVERVIEW 1.
Basic Operation JBL 9 4 2-6 10 8 3 15 5 12 6 13 11 7 16 1 14 2
Basic Operation SDP-40 When a 5.1-channel analog source is present in the Main Zone and the INPUT SETUP menu ZONE2 IN or RECORD IN parameter is set to DMIX, only the (L) and (R) input signals are sent to the Zone 2 or Record Zone audio output connectors. Input Connector(s) (L) & (R) Output Connector(s) Front L/R (C) Center (SUB) Subwoofer L/R & LFE (LS) & (RS) Side L/R & Rear L/R 7. Record Zone Audio Output Connectors Provide analog and digital audio output in the Record Zone.
Basic Operation Rear Panel Overview (continued from page 2-7) 10.Main Zone Video Output Connectors Provide video output in the Main Zone. Two composite video connectors, two S-video connectors, and one component video connector (BNC) are available. The composite and S-video connectors labeled 1 (OSD) incorporate the on-screen display. JBL 13.Trigger Output Connectors Provide 12V DC output to control connected components. Three trigger output connectors are available on a removable terminal block.
SDP-40 Basic Operation REMOTE CONTROL OVERVIEW The SDP-40 remote control provides full operation of the SDP-40, performing commands such as menu navigation that are not available from the front panel. The command matrix that begins on page 2-14 indicates the commands remote control buttons perform when each command bank is activated. The numbered items in the matrix correspond with the remote control illustrations on pages 2-14 to 2-18.
Basic Operation JBL MAIN MENU The MAIN MENU represents the beginning of the menu structure. It can be used to open the three main menu branches: MODE ADJUST, AUDIO CONTROLS, and SETUP. Button MENU 2-10 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP MENU NAVIGATION The remote control MENU and arrow buttons must be used to navigate the extensive menu structure shown in the Appendix. The table below indicates the navigation commands remote control buttons perform when the Main Zone command bank is activated.
Basic Operation SDP-40 MENU ITEM SELECTION The remote control arrow buttons must be used to select menu items. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS DISPLAY SETUP ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF CUSTOM NAME OFF OFF EDIT CUSTOM NAME ON OFF To select a menu item on the open menu: 1. Press the and arrow buttons to highlight the desired menu item. 2.
Basic Operation JBL To select a parameter setting with a horizontal graph: To activate a command bank: 1. When the horizontal graph appears, press the and arrow buttons to increase and decrease the setting in designated increments. The current setting appears at the right of the parameter name on the on-screen and front panel displays. 1. Press and release a command bank selection button to activate the desired command bank. 2.
Basic Operation SDP-40 2 1 LIGHT 3 MAIN ZONE Button SHIFT DVD-1 DVD-2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX FP MODE BLUE Zone 2 Record Zone Shift Activates and deactivates standby mode when the SDP-40 is powered on with the rear panel power switch. The standby button performs no function when the SDP-40 is powered off with the rear panel power switch.
Basic Operation JBL Button LIGHT MAIN ZONE 4 REC Main Zone Zone 2 Record Zone SA T Selects the SAT input for the Main Zone. Selects the SAT input for Zone 2. Selects the SAT input for the Record Zone. Sets the AUDIO CONTROLS menu LOUDNESS parameter to OFF. VC R Selects the VCR input for the Main Zone. Selects the VCR input for Zone 2. Selects the VCR input for the Record Zone. Reserved for future expansion. CD Selects the CD input for the Main Zone. Selects the CD input for Zone 2.
Basic Operation SDP-40 Button LIGHT MAIN ZONE REC 5 FP 6 BLUE 7 O SD SHIFT DVD-1 DVD-2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX 5 6 FP 8 MODE BLUE VOL 9 OSD STAT MUTE 7 10 8 MODE MENU 7/5 2 CH MUSIC 9 VOL 10 M UTE Main Zone Zone 2 Record Zone Shift Toggles the FRONT PANEL DISPLAY menu STATUS parameter between ALWAYS OFF and its current setting. Sets Zone 2 volume level to -15dB. Sets Record Zone volume level to -15dB. Sets Main Zone volume level to -15dB.
Basic Operation JBL Button LIGHT MAIN ZONE 11 REC STAT Main Zone Zone 2 Record Zone Shift Displays the Main Zone two-line status for 2 seconds. Displays the Zone 2 two-line status for 2 seconds. Displays the Record Zone two-line status for 2 seconds. Opens and closes the status menu for the current input source. When a menu is open, pressing the MENU button closes the menu structure. When no menus are open, pressing the MENU button opens the MAIN MENU.
Basic Operation SDP-40 Button LIGHT MAIN ZONE 16 REC Main Zone Zone 2 Record Zone Selects the THX mode family for the current input source. Reserved for future expansion. Reserved for future expansion. Activates the 5.1 , 5.1 ULTRA2 , or 5.1 SurEX listening mode when a 5.1-channel Dolby Digital source is present. Selects the Dolby mode family for the current input source. Reserved for future expansion. Reserved for future expansion.
Basic Operation UNDERSTANDING THE ZONES The SDP-40 features three zones of operation, called the Main Zone, Zone 2, and the Record Zone. The Main Zone controls audio and video sources in the primary listening space. Zone 2 controls audio and video sources in the secondary listening space. And, the Record Zone controls audio and video sources sent to recording devices or to a third listening space. JBL 3.
Basic Operation SDP-40 Record Zone Two-Line Status STATUS MENUS Opens on the on-screen and front panel displays whenever the SDP-40 detects a Record Zone status change. The Record Zone two-line status indicates the current input, DVD1 %!D VOL input source, and volume level selected in the RECORD -34dB Record Zone. When the Shift command bank is activated, pressing the remote control STAT button opens the status menu for the current input source.
Basic Operation 2CH STATUS INPUT MODE INPUT TYPE SAMPLE RATE dB L 0 -6 -15 -30 C X R X %!D STATUS INPUT MODE CHANNELS BIT RATE EX ENCODED SL SR SB LFE X JBL X X X X dB 0 -6 -15 -30 L C X R X PG1 SL SR SB LFE X X X X -45 -45 5.1 ANALOG STATUS INPUT MODE INPUT TYPE SAMPLE RATE 5.1a BYPASS STATUS INPUT MODE INPUT TYPE dB 0 -6 -15 -30 L C X R X %!D STATUS SAMPLE RATE 2.
Basic Operation SDP-40 D STATUS & •Provides information about Dolby Digital sources. STATUS • Provides information about dts(-ES) sources. • Includes L, C, R, SL, SR, and LFE level meters. • Includes L, C, R, SL, SR, SB, and LFE level meters. Parameter Possible Settings Parameter Possible Settings INPUT The current input INPUT The current input MODE The current listening mode MODE The current listening mode CHANNELS 3/2.1, 3/2, 3/1, 2/2, 2/1, 2/0, 1/0 CHANNELS 3/3.1, 3/2.
Basic Operation JBL 5.1 ANALOG STATUS • Provides information about 5.1-channel analog sources. • Includes L, C, R, SL, SR, and LFE level meters. 2CH BYPASS STATUS • Provides information about 2-channel analog sources when the MAIN ADV menu ANALOG BYPASS parameter is set to ON. Parameter Possible Settings Parameter Possible Settings INPUT The current input INPUT The current input MODE The current listening mode MODE 2CH BYPASS INPUT TYPE ANLG INPUT TYPE BYPASS SAMPLE RATE 44.
Basic Operation SDP-40 STATUS MENU PARAMETER DESCRIPTIONS 2.0 ENCODING MATRIX, NONE Indicates whether or not a matrix-encoded source is detected. When the parameter setting is MATRIX, a matrix-encoded source is detected. When the parameter setting is NONE, a matrix-encoded source is not detected. The SDP-40 cannot automatically detect matrix encoding in non-flagged input sources. BIT RATE 32 to 640 kbps or 754 to 1509.7kbps Indicates the rate at which the input signal is encoded.
Basic Operation JBL INPUT WORD LENGTH Indicates the current input (i.e. DVD1). Indicates the word length of the audio data present in the input signal. INPUT TYPE ANLG, BYP, PCM, --- Indicates the input source that is present. When the parameter setting is ANLG, an analog audio source is present and the MAIN ADV menu ANALOG BYPASS parameter is set to OFF. When the parameter setting is BYP, an analog audio source is present and the ANALOG BYPASS parameter is set to ON.
3 SETUP SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 INPUT SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Changing Input Names • Assigning Audio & Video Input Connectors • Selecting Preferred Listening Modes • Configuring Advanced Input Settings SPEAKER SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETUP JBL REAR PANEL CONFIG SETUP Selecting the MAIN MENU SETUP option opens the SETUP menu shown below, which can be used to configure the SDP-40. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUTS SETUP INPUTS Prompts the selection of the desired input (i.e. DVD1).
SETUP SDP-40 LOCK OPTIONS SETUP LOCK OPTIONS Opens the LOCK OPTIONS menu, which can be used to protect MODE ADJUST, AUDIO CONTROLS, and SETUP menu branch parameter settings from accidental changes. Refer to page 3-50 for more information. INPUT SETUP SETUP INPUTS DVD1 DVD1 INPUT SETUP Selecting the SETUP menu INPUTS option prompts the selection of the desired input (i.e. DVD1).
SETUP JBL CHANGING INPUT NAMES SETUP INPUTS DVD1 NAME Selecting the INPUT SETUP menu NAME option opens the INPUT NAME menu shown below, which can be used to customize or restore the factory-default name of the selected input. Factory-default input names correspond to front panel and remote control input selection button labels.
SETUP SDP-40 • Press the arrow button to return to the previous character space. When the cursor is positioned in the first character space, pressing the arrow button will close the EDIT INPUT NAME drop-down menu. 4. When the desired input name has been entered, press the arrow button until the EDIT INPUT NAME drop-down menu closes. RESTORE DEFAULT NAME SETUP INPUTS DVD1 NAME RESTORE DEFAULT NAME Restores the factory-default name of the selected input.
SETUP JBL ASSIGNING AUDIO & VIDEO INPUT CONNECTORS The SDP-40 has 12 configurable inputs, each of which can be assigned to its 13 digital audio, 8 analog audio, 5 composite video, 8 S-video, or 4 component video input connectors.
SETUP SDP-40 When no digital audio input connector is assigned, the SDP-40 automatically sets the: • MAIN ADV menu INPUT SELECT parameter to ANALOG • INPUT SETUP menu ZONE2 IN parameter to ANLG • INPUT SETUP menu RECORD IN parameter to ANLG ANALOG IN SETUP INPUTS ANALOG-1 to 8, 5.1 ANLG (6-8), NONE DVD1 The configuration of the analog audio input connectors determines available ANALOG IN parameter settings.
SETUP JBL Assigning Audio & Video Input Connectors (continued from page 3-7) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
SETUP SDP-40 AUTO SETUP ON, OFF INPUTS DVD1 ANLG IN LVL AUTO AUTO GAIN SETUP Activates automatic adjustment of 2-channel analog audio input levels. When ON is selected, the SDP-40 automatically monitors and optimizes 2-channel analog audio input levels. When the input signal is too high, the SDP-40 quickly decreases input levels to avoid overload. When the input signal is too low, the SDP-40 slowly increases input levels to maximize signal-to-noise ratio and dynamic range.
SETUP JBL Assigning Audio & Video Input Connectors VIDEO IN SETUP (continued from page 3-9) COMPOSITE-1 to 5, S-VIDEO-1 to 8, NONE INPUTS DVD1 VIDEO IN COMPONENT IN SETUP Opens the VIDEO IN menu shown below, which can be used to assign a composite or S-video input connector for the selected input. INPUTS Note: • Composite video output connectors are available when a composite or S-video source is present. • • S-video output connectors are available when an S-video source is present.
SETUP SDP-40 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
SETUP JBL Selecting Preferred Listening Modes MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP DVD1 SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS MODE FILM MUSIC 2-CHAN USE LAST (continued from page 3-11) INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
SETUP SDP-40 was activated the last time a 2-channel source was present. The SDP-40 will not activate a listening mode unless a 44.1 or 48kHz PCM digital source is present. The listening modes are not compatible with 88.2 or 96kHz, Dolby Digital, or analog sources. R R Note: When the 2-CH parameter is set to USE LAST, the SDP-40 will not activate the 2-CHANNEL listening mode if the 2CH button was used to activate the 2-CHANNEL listening mode the last time a 2-channel source was present.
SETUP JBL CONFIGURING ADVANCED INPUT SETTINGS MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
SETUP SDP-40 Parameter Possible Settings INPUT SELECT DIGITAL, ANALOG, AUTO ANALOG BYPASS ON, OFF S-VIDEO 16:9 AUTO, OFF S-VIDEO OSD 4:3 ON, OFF COMPONENT OSD ON, OFF INPUT SELECT SETUP INPUTS • When a 5.1-channel analog source is present, the SDP-40 passes analog input signals to the Main Zone audio output connectors as indicated in the table on pages 2-7 and 3-41.
SETUP JBL Configuring Advanced Input Settings (continued from page 3-15) INPUT SELECT Parameter Settings DIGITAL ANALOG AUTO The SDP-40 sends the assigned digital audio input connector to the Main Zone audio output connectors. The SDP-40 ignores the assigned analog audio input connector. The SDP-40 sends the assigned analog audio input connector to the Main Zone audio output connectors. The SDP-40 ignores the assigned digital audio input connector.
SETUP SDP-40 S-VIDEO OSD 4:3 SETUP INPUTS DVD1 ON, OFF MAIN ADVANCED S-VIDEO OSD 4:3 Controls the on-screen display aspect ratio when the display device is connected to a Main Zone S-video output connector. Aspect ratio refers to the size of the picture or the display device screen. A 4:3 aspect ratio is almost square. A 16:9 aspect ratio, often referred to as widescreen, is almost twice as wide as high.
SETUP JBL Configuring Advanced Input Settings (continued from page 3-17) ZONE2 & RECORD IN Parameter Settings DIGITAL ANLG (Analog) DMIX (Downmix) The SDP-40 sends the assigned digital audio input connector to the Zone 2 or Record Zone audio output connectors. The SDP-40 ignores the assigned analog audio input connector. Independent zone monitoring is available. The SDP-40 sends the assigned analog audio input connector to the Zone 2 or Record Zone audio output connectors.
SETUP SDP-40 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.1a FILM MAIN ADVANCED ZONE2 IN DIGITAL RECORD IN DIGITAL RECORD ADVANCED -18 to +12dB DVD1 RECORD ADV ANLG IN LVL +0dB DIGITAL BYPASS OFF DIG OUT RATE 44.
SETUP JBL Configuring Advanced Input Settings (continued from page 3-19) DIG OUT RATE SETUP ANLG IN LVL SETUP INPUTS -18 to +12dB DVD1 RECORD ADVANCED ANLG IN LVL Allows adjustment of analog audio input levels for input signals sent to the Record Zone digital audio output connectors. The SDP-40 applies these adjustments to input signals before passing them to the Record Zone digital audio output connectors.
SETUP SDP-40 SPEAKER SETUP SETUP Note: SPEAKERS The SDP-40 Balanced also includes 10 balanced Main Zone audio output connectors labeled Front L/R, Center, LFE, Subwoofer L/R, Side L/R, and Rear L/R. Two additional audio output connectors labeled Aux L/R are provided for future expansion. Selecting the SETUP menu SPEAKERS option opens the SPEAKER SETUP menu shown below, which can be used to configure the Main Zone audio output connectors for the desired speaker setup.
SETUP JBL Setting Crossover Points (continued from page 3-21) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz SR RR 80Hz 80Hz C 80Hz M SUB 80Hz Custom Speaker Setups SETUP SPEAKERS SET CROSSOVERS CUSTOM SETUP To configure a custom speaker setup: Select the crossover point closest to the low-frequency rating of the associate
SETUP SDP-40 Highpass Filter Lowpass Filter dB 0 0 -12 -24 -36 -48 0 0 -60 10 Highpass filters attenuate low-frequency signals at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover point. From left to right, the curves represent crossover points from 30 to 120Hz. This graph does not include the THX 80Hz crossover point, which attenuates low-frequency signals at 12dB per octave.
SETUP JBL Setting Crossover Points (continued from page 3-23) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS THX SETUP 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz SR RR 80Hz 80Hz C 80Hz M SUB 80Hz L 80Hz SL RL 80Hz SPEAKERS SET CROSSOVERS SYNTHESIS 7CH SETUP Selecting the CROSSOVER SETUP menu SYNTHESIS 7CH SETUP option opens the SYNTHESIS 7CH SPEAKER SETUP screen
SETUP SDP-40 Speaker Setup Parameters SETUP SPEAKERS SET CROSSOVERS CUSTOM SETUP OR SETUP SPEAKERS The table below indicates the speaker setup parameters that can be used to configure the Main Zone audio output connectors for the desired speaker setup. These parameters appear on the CUSTOM and SYNTHESIS 7CH SETUP menus. SET CROSSOVERS Speaker setup parameters perform the same function regardless of which speaker setup is selected.
SETUP JBL Setting Crossover Points (continued from page 3-25) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz SR RR 80Hz 80Hz C 80Hz M SUB 80Hz SUB XOVER FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz FRONT L/R SUBWOOFERS L/R MONO STEREO NONE REAR L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 9
SETUP SDP-40 SETUP SPEAKERS SET CROSSOVERS SYNTHESIS 7CH SETUP When a SYNTHESIS 7CH speaker setup is selected, the FRONT L/R parameter cannot be adjusted. The SDP-40 automatically applies a 80Hz crossover point to the Front L/R output connectors. SIDE L/R Assigns a crossover point for the Main Zone audio output connectors labeled Side L/R. SETUP CENTER FULL, 30 to 120Hz, THX 80Hz, NONE Assigns a crossover point for the Main Zone audio output connector labeled Center.
SETUP JBL Setting Crossover Points (continued from page 3-27) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS THX SETUP 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz SR RR 80Hz 80Hz C SYNTHESIS 7CH SETUP !CAUTION! PRESSING THE V BUTTON WILL AUTOMATICALLY CHANGE THE OUTPUTS TO A SYNTHESIS SPEAKER CONFIGURATION 80Hz M SUB 80Hz L 80Hz SL 80Hz RL SYNTHESIS 7CH SETUP FRONT
SETUP SDP-40 SUB L/R SETUP SPEAKERS MONO, STEREO, NONE SET CROSSOVERS CUSTOM SETUP SUB L/R Configures the Main Zone audio output connector labeled Subwoofer L/R for a speaker setup that includes one, two, or no subwoofer(s). When a custom speaker setup is selected, the SUB L/R parameter opens the SUBWOOFERS L/R menu shown on page 3-26, which can be used to select the desired configuration for the Subwoofer L/R output connectors. • Select MONO if the speaker setup includes one subwoofer.
SETUP JBL Setting Crossover Points (continued from page 3-29) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz SR RR 80Hz 80Hz C 80Hz M SUB 80Hz SYNTHESIS 7CH SETUP !CAUTION! PRESSING THE V BUTTON WILL AUTOMATICALLY CHANGE THE OUTPUTS TO A SYNTHESIS 7CH SPEAKER CONFIGURATION ON, OFF Activates and deactivates the Main Zone audi
SETUP SDP-40 ULTRA2 SUB SETUP SPEAKERS OR SETUP SPEAKERS ON, OFF SET CROSSOVERS SET CROSSOVERS CUSTOM SETUP THX SETUP @** ULTRA2 SUB @** ULTRA2 SUB Select ON if the subwoofer using the Main Zone audio output connectors labeled Subwoofer L/R is THX Ultra2-certified. When ON is selected, the BGC parameter can be used to adjust boundary gain compensation. Select OFF if the subwoofer using the Main Zone audio output connectors labeled Subwoofer L/R is not THX Ultra2-certified.
SETUP JBL CALIBRATING SPEAKER DISTANCES & OUTPUT LEVELS The SDP-40 offers manual calibration of speaker distances and output levels. Calibration helps to ensure accurate output signal arrival time and level at the primary listening position. However, it is not a substitute for proper speaker placement. Before calibrating speaker distances and output levels: Speaker Distance Parameters • Set crossover points for the Main Zone audio output connectors.
SETUP SDP-40 Speaker Distance Settings Parameter Output Level Settings Default Setting Possible Settings Default Setting Possible Settings FRONT LEFT +0.0ft +0.0 to 30.0ft or 12.0m +0.0dB -18.0 to +12.0dB CENTER +0.0ft +0.0 to 30.0ft or 12.0m +0.0dB -18.0 to +12.0dB FRONT RIGHT +0.0ft +0.0 to 30.0ft or 12.0m +0.0dB -18.0 to +12.0dB SIDE LEFT +0.0ft +0.0 to 30.0ft or 12.0m +0.0dB -18.0 to +12.0dB REAR LEFT +0.0ft +0.0 to 30.0ft or 12.0m +0.0dB -18.0 to +12.0dB REAR RIGHT +0.
SETUP SDP-40 MANUAL CALIBRATION SETUP SPEAKERS MANUAL Selecting the SPEAKER SETUP menu MANUAL option opens the MANUAL SPEAKER SETUP menu shown below, which can be used to manually calibrate speaker distances and output levels. The table below indicates available manual calibration options.
SETUP JBL Performing Manual Speaker Distance Calibration SETUP SPEAKERS MANUAL SPEAKER DISTANCES Selecting the MANUAL SPEAKER SETUP menu SPEAKER DISTANCES option opens the SPEAKER DISTANCES menu shown below, which can be used to manually calibrate speaker distances. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER SPEAKER DISTANCES DISTANCES LEVELS CALIBRATION R +0.
SETUP SDP-40 Performing Manual Output Level Calibration SETUP SPEAKERS MANUAL LEVELS CALIBRATION Selecting the MANUAL SPEAKER SETUP menu LEVELS CALIBRATION option opens the LEVELS CALIBRATION menu shown below, which can be used to manually calibrate output levels. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R +0.0dB S R RR +0.
SETUP JBL Performing Manual Output Level Calibration (continued from page 3-36) To manually calibrate output levels during the internal noise test: 1. Set the SPL meter to “C” weighting and “SLOW” response. INTERNAL NOISE TEST SETUP SPEAKERS MANUAL LEVELS CALIBRATION INTERNAL NOISE TEST Opens the INTERNAL NOISE message shown on the previous page, which indicates that the internal noise test generates loud calibration noise signals.
SETUP SDP-40 Note: The internal noise and DACS CALIBRATON modes will turn on TRIGGER1 . DACS CALIBRATION SETUP SPEAKERS MANUAL LEVELS CALIBRATION DACS CALIBRATION Selecting DACS CALIBRATION accesses the SPEAKER LEVEL ADJUST menu (pictured on page 3-36). DACS CALIBRATION requires an external noise source. In JBL Synthesis systems, this source is the JBL Digital Acoustical Calibration System (DACS®). However, an alternate source such as an audio calibration disc can also be used.
SETUP JBL SETTING BASS PEAK LIMITERS SETUP SPEAKERS MANUAL LEVELS CALIBRATION BASS PEAK LIMITERS Selecting the LEVELS CALIBRATION menu BASS PEAK LIMITERS option opens the BASS PEAK LIMITERS menu shown below, which can be used to set amplitude limits for low-frequency signals sent to the Main Zone audio output connectors labeled Subwoofer L/R and LFE as well as low-frequency signals redirected to other Main Zone audio output connectors.
SETUP SDP-40 CAL NOISE SETUP SPEAKERS ON, OFF MANUAL LEVELS CALIBRATION BASS PEAK LIMITERS CAL NOISE LFE LIMITER SETUP SPEAKERS ON, OFF MANUAL LEVELS CALIBRATION BASS PEAK LIMITERS LFE LIMITER Determines whether bass peak limiters are set with an internal or external calibration source. When ON is selected, the SDP-40 activates an internal calibration noise signal to set bass peak limiters. When OFF is selected, the SDP-40 deactivates the internal calibration noise signal.
SETUP JBL 5 STEREO & 5.1 ANLG REAR PANEL CONFIG SETUP SETUP REAR PANEL CONFIG Selecting the SETUP menu REAR PANEL CONFIG option opens the REAR PANEL CONFIG menu shown below, which can be used to configure the analog audio input connectors as eight stereo connectors or as five stereo and one 5.1-channel connectors. REAR PANEL CONFIG 5 STEREO & 5.1 ANLG Select the 5 STEREO & 5.1 ANLG option to configure the analog audio input connectors as five stereo and one 5.1-channel connectors.
SETUP SDP-40 DISPLAY SETUP SETUP DISPLAYS Selecting the SETUP menu DISPLAYS option opens the DISPLAY SETUP menu shown below, which can be used to customize the on-screen and front panel displays, restore audio/video synchronization, and create and activate a custom unit name.
SETUP JBL Display Setup (continued from page 3-42) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS EDIT CUSTOM NAME SETUP DISPLAYS EDIT CUSTOM NAME Opens the EDIT CUSTOM NAME drop-down menu shown above, which can be used to create a custom unit name. The factorydefault unit name is SDP-40. To create a custom unit name: 1. Follow the EDIT CUSTOM NAME menu path shown above to open the EDIT CUSTOM NAME drop-down menu. 2.
SETUP SDP-40 ON-SCREEN DISPLAY SETUP DISPLAYS ON-SCREEN DISPLAY Selecting the DISPLAY SETUP menu ON-SCREEN DISPLAY option opens the ON-SCREEN DISPLAY menu shown below, which can be used to customize the on-screen display.
SETUP JBL On-Screen Display (continued from page 3-44) POSITION SETUP DISPLAYS Note: ON-SCREEN DISPLAY POSITION Controls the vertical alignment of the two-line status on the display device screen. When TOP is selected, the two-line status appears near the top of the display device screen. When CENTER is selected, the two-line status appears centered on the display device screen. When BOTTOM is selected, the two-line status appears near the bottom of the display device screen.
SETUP SDP-40 FRONT PANEL DISPLAY SETUP DISPLAYS FRONT PANEL DISPLAY Opens the FRONT PANEL DISPLAY menu shown below, which can be used to customize the front panel display.
SETUP JBL MAIN PWR ON VOLUME CONTROL SETUP SETUP SETUP VOLUME CONTROLS Selecting the SETUP menu VOLUME CONTROLS option opens the VOLUME CONTROL SETUP menu shown below, which can be used to configure Main Zone, Zone 2, and Record Zone volume levels.
SETUP SDP-40 REC PWR ON SETUP LAST LVL, -80 to +6dB VOLUME CONTROLS REC PWR ON MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP Selects the volume level at which the Record Zone activates. When a value is selected, the SDP-40 automatically sets Record Zone volume level to the selected value when the Record Zone is activated. When LAST LVL is selected, the SDP-40 sets Record Zone volume level to the last volume level that was selected in the Record Zone during the previous operating session.
TRIGGER SETUP TRIGGER 1 REMOTE TRIGGER 2 REMOTE TRIGGER 2 SETUP REMOTE ONLY DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX ZONE2 INPUTS RECORD INPUTS FILM TV MUSIC MUSIC SURR PLII + PLII MOVIE PLII MUSIC PRO LOGIC FILM MUSIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC 5.1 SurEX 5.1 MUSIC DIGITAL EX 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM MUSIC R R MUSIC 2-CHAN 5.1a FILM 5.1a MUSIC 5.1a SurEX 5.1a MUSIC 5.
SETUP SDP-40 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS LOCK OPTIONS SETUP UNLOCKED AUDIO CNTRL UNLOCKED MODES UNLOCKED LOCKED UNLOCKED When configured for program operation, the connector activates when the associated inputs or listening modes are activated and deactivates when the associated inputs or listening modes are deactivated.
SETUP JBL SETUP SETUP LOCKED, UNLOCKED LOCK OPTIONS SETUP Protects SETUP menu branch settings from accidental changes. When LOCKED is selected, SETUP menu branch settings cannot be adjusted. When UNLOCKED is selected, SETUP menu branch settings can be adjusted. Note the following: • When the MODES parameter is set to LOCKED, the up and down arrows can still be used to adjust subwoofer output levels applied to the selected listening mode when the Shift command bank is activated.
4 AUDIO CONTROLS AUDIO CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUDIO CONTROLS JBL AUDIO CONTROLS Selecting the MAIN MENU AUDIO CONTROLS option opens the AUDIO CONTROLS menu shown below, which can be used to customize the Main Zone, Zone 2, and Record Zone audio output connectors. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP L< • • • <|> >R AUDIO CONTROLS BASS +0.0dB TREBLE +0.0dB TILT EQ +0.
AUDIO CONTROLS SDP-40 BASS -6.0 to +6.0 AUDIO CONTROLS BASS BASS Controls the amount of low-frequency boost or cut applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. The graph shown at the right indicates the frequency response of all BASS parameter settings. +6.0 +5.5 +5.0 +4.5 +4.0 +3.5 Note: +3.0 When the Shift command bank is activated: +2.0 • Pressing the CD button increases the BASS parameter setting in 0.5dB increments. +1.
AUDIO CONTROLS TREBLE JBL -6.0 to +6.0 AUDIO CONTROLS TREBLE TREBLE Controls the amount of boost or cut applied to the Main Zone audio output connectors labeled Front L/R and Center. The graph shown at the right indicates the frequency response of all TREBLE parameter settings. +6.0 +5.5 +5.0 +4.5 +4.0 +3.5 +3.0 +2.5 +2.0 +1.5 +1.0 +0.5 +0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 -5.5 -6.
AUDIO CONTROLS SDP-40 TILT EQ -3.0 to +3.0 AUDIO CONTROLS TILT EQ TILT EQ Controls the amount of tilt equalization applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. This parameter setting affects the entire frequency spectrum with a hinge point at 1kHz. As the setting increases, frequencies higher than 1kHz are boosted while frequencies lower than 1kHz are simultaneously cut.
AUDIO CONTROLS LOUDNESS AUDIO CONTROLS JBL ON, OFF LOUDNESS Controls the amount of low-frequency boost that is automatically applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. When ON is selected, loudness compensation is automatically applied based on volume level. As volume level increases, the amount of low-frequency boost automatically decreases. The loudness contour is optimized for input sources calibrated to THX reference levels.
AUDIO CONTROLS SDP-40 BALANCE L< to <|> to >R AUDIO CONTROLS BALANCE ZONE2 BALANCE AUDIO CONTROLS Controls the left-to-right balance of the Main Zone audio output connectors labeled Front L/R. L< to <|> to >R ZONE2 BALANCE Controls the left-to-right balance of the Zone 2 audio output connectors. Note: Note: When the Shift command bank is activated: When the Zone 2 command bank is activated: • Pressing the MENU button centers the Main Zone BALANCE parameter.
5 MODE ADJUST MODE ADJUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Listening Mode Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Preferred Listening Mode Selection Parameters • Mode Buttons • Mode Family Selection Buttons Listening Mode Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODE ADJUST MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP JBL MODE ADJUST FILM TV MUSIC MUSIC SURR PLII + PLII MOVIE PLII MUSIC PRO LOGIC FILM MUSIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC 5.1 * 5.1 MUSIC DIGITAL* 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM* MUSIC* * MUSIC * 2-CHAN* 5.1a FILM 5.1a MUSIC 5.1a * 5.1a MUSIC 5.1a STANDARD 5.1a 2-CHANNEL 5.
MODE ADJUST SDP-40 PREFERRED LISTENING MODE SELECTION PARAMETERS DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.1a FILM MAIN ADVANCED ZONE2 IN DIGITAL RECORD IN DIGITAL RECORD ADVANCED The SDP-40 allows the selection of four preferred listening modes for each Main Zone input, including one listening mode each for 2-channel, Dolby Digital, dts(-ES), and 5.1-channel analog sources.
MODE ADJUST JBL MODE BUTTONS MODE FAMILY SELECTION BUTTONS The front panel and remote control Mode buttons can be used to audition listening modes with the current Main Zone input source. Pressing the Mode or + button scrolls upward through listening modes available for the current Main Zone input source. Pressing the Mode or – button scrolls downward through listening modes available for the current Main Zone input source.
MODE ADJUST SDP-40 LISTENING MODE DESCRIPTIONS The SDP-40 offers an assortment of listening modes for 2-channel, Dolby Digital, dts(-ES), and analog sources. Listening mode descriptions begin below and continue in the order shown on the MODE ADJUST menu. The table included with each description indicates the corresponding listening mode menu parameters, as well as their factory-default and possible parameter settings. All listening mode menus are shown in the Appendix beginning on page A-14.
MODE ADJUST JBL TV MODE ADJUST MUSIC L7 TV MODE ADJUST L7 MUSIC • A proprietary listening mode. • A proprietary listening mode. • Similar to the FILM listening mode, but specifically tailored for broadcast sources. • Similar to the FILM listening mode, but specifically tailored for music sources. • Designed for enhanced playback of 2-channel stereo or matrixencoded broadcast sources. • Designed for enhanced playback of 2-channel stereo or matrixencoded music sources.
MODE ADJUST SDP-40 MUSIC SURR MODE ADJUST PLII + L7 MUSIC SURR MODE ADJUST @*PLII + @** • A proprietary listening mode. • Designed for playback of Dolby Surround-encoded sources. • Similar to the MUSIC SURROUND listening mode available in other JBL products. • Uses Dolby Pro Logic II decoding to derive five channels from Dolby Surround-encoded sources.
MODE ADJUST JBL PLII MOVIE MODE ADJUST • PLII MUSIC @*PLII MOVIE Similar to the PRO LOGIC listening mode, but uses fullfrequency stereo surround channels to realistically increase the perceived width of the listening space. MODE ADJUST @*PLII MUSIC • Similar to the PLII MOVIE listening mode. • Designed for playback of stereo music sources. • Designed for playback of Dolby Surround-encoded sources. • Decodes five channels from Dolby Surround-encoded sources.
MODE ADJUST SDP-40 PRO LOGIC MODE ADJUST Parameter @*PRO LOGIC OUTPUT LEVELS Refer to page 5-32 Refer to page 5-33 • Designed for playback of Dolby Surround-encoded sources. CUSTOM • Decodes four channels from Dolby Surround-encoded sources. Listening mode menu parameter descriptions begin on page 5-34. • Uses a mono surround channel with a high-frequency rolloff above 7kHz.
MODE ADJUST JBL NIGHTCLUB MODE ADJUST • CONCERT HALL NIGHTCLUB MODE ADJUST CONCERT HALL Designed for playback of “dry” music sources that benefit from the addition of room reflections, especially music sources that lack ambience in the recording. • Generates early reflections to simulate large listening spaces. • Sends early reflections to the front, side, and rear channels. • Generates early reflections to simulate small, intimate listening spaces.
MODE ADJUST SDP-40 CHURCH MODE ADJUST • • CATHEDRAL CHURCH MODE ADJUST Uses a reverb algorithm to emphasize the rich, smooth, reverberant decay characteristic of small and medium listening spaces with long reverberation time relative to their size, such as churches and chambers. Unlike other room simulation listening modes, this mode uses a proprietary reverb algorithm that is relied upon by a majority of recording engineers to add ambience to recordings.
MODE ADJUST JBL PANORAMA MODE ADJUST CALIBRATION PANORAMA MODE ADJUST • Designed for playback of stereo and matrix-encoded sources. • Uses proprietary algorithms to move the stereo image outward from the front speakers, producing a wider stereo field with greater depth. • Depends on proper location of the primary listening position and front speakers.
MODE ADJUST SDP-40 Front Left Front Left Front Right Front Left Front Right Front Right 60° L127 . . . . . . Center . . . . . . R127 Primary Listening Position 5-A 5-B To calibrate the PANORAMA listening mode: 1. Remove all obstructions between the primary listening position and the speakers. 2. Make sure the distances between the primary listening position and the speakers are properly measured.
MODE ADJUST JBL PARTY MONO LOGIC MODE ADJUST PARTY MODE ADJUST MONO LOGIC • Designed for playback of stereo sources. • Designed for playback of mono sources. • Sends stereo sources to all channels. • • Recommended for background music. Uses proprietary reverb algorithms to realistically expand mono sources to use all channels, dramatically increasing the perceived width and sense of envelopment of the listening space.
MODE ADJUST SDP-40 MONO SURROUND MODE ADJUST 5.1 MONO SURROUND FILM MODE ADJUST 5.1 L7 FILM • Designed for playback of mono sources. • A proprietary listening mode. • Sends mono sources to all channels. • Designed for enhanced playback of 5.1-channel Dolby Digital film sources. • Derives seven channels from 5.1-channel sources. When both side and rear speakers are present, the 5.1 FILM listening mode also increases the perceived length and sense of envelopment of the listening space.
MODE ADJUST 5.1 JBL TV MODE ADJUST 5.1 5.1 L7 TV MUSIC MODE ADJUST 5.1 L7 MUSIC • A proprietary listening mode. • A proprietary listening mode. • Similar to the 5.1 FILM listening mode, but specifically tailored for broadcast sources. • Similar to the 5.1 FILM listening mode, but specifically tailored for music sources. • Designed for enhanced playback of 5.1-channel Dolby Digital broadcast sources. • Designed for enhanced playback of 5.1-channel Dolby Digital music sources.
MODE ADJUST SDP-40 5.1 ULTRA2, 5.1 MODE ADJUST SurEX, & 5.1 • The 5.1 Ultra2 and 5.1 SurEX listening modes are not available unless both side and rear speakers are present. • The 5.1 listening mode is available when neither THX Ultra2 nor THX Surround EX decoding is engaged. 5.1 @** ULTRA2 OR 5.1 @** SurEX OR 5.1 @** Listening mode name differs depending on the encoding present in the input source, the SURROUND EX parameter setting, and the speaker setup.
MODE ADJUST 5.1 ULTRA2, 5.1 JBL SurEX, & 5.1 (continued from page 5-17) MODE ADJUST 5.1 @** ULTRA2 OR 5.1 @** SurEX OR 5.1 @** When THX Surround EX decoding is engaged: • Applies matrix decoding to derive three surround channels from 5.1-channel Dolby Digital sources. • Designed for playback of 5.1-channel Dolby Digital film sources. • Allows 7-channel playback of 5.1-channel Dolby Digital sources without THX Surround EX encoding.
MODE ADJUST SDP-40 5.1 MUSIC MODE ADJUST DIGITAL EX & 5.1 @** MUSIC MODE ADJUST • Designed for playback of 5.1-channel Dolby Digital music sources. • The 5.1 MUSIC listening mode is not available unless both side and rear speakers are present. • Applies ASA processing to signals sent to the rear speakers. Refer to the ASA parameter description on page 3-31 for more information. • Recommended for home theaters.
MODE ADJUST DIGITAL EX & MODE ADJUST JBL DIGITAL (continued from page 5-19) When Dolby Digital Surround EX decoding is engaged: @*DIGITAL EX OR @*DIGITAL • Note: The SDP-40 cannot automatically detect Dolby Digital Surround EX encoding in non-flagged 5.1channel Dolby Digital sources. A non-flagged input source does not include information in the input signal t h a t identifies Dolby Digital Surround EX encoding. • • Designed for playback of 5.1-channel Dolby Digital sources.
MODE ADJUST SDP-40 5.1 2-CHANNEL MODE ADJUST 5.1 MONO LOGIC 5.1 2-CHANNEL MODE ADJUST • Designed for converting 5.1-channel Dolby Digital input signals into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.1-channel Dolby Digital input signals to the front speakers and the subwoofer. • Recommended for recording purposes.
MODE ADJUST JBL 5.1 MONO SURR MODE ADJUST DECODING 5.1 MONO SURR • Designed for playback of Dolby Digital mono sources. • Sends mono sources to all channels. and listening mode names differ depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. The table at the top of the next page indicates the conditions in which dts-ES decoding is engaged. • listening modes are available when dts-ES decoding is not engaged.
MODE ADJUST SDP-40 Input Source 5.1-Channel dts Parameter Setting 5.1-Channel Matrix-Encoded dts-ES 6.1-Channel Discrete-Encoded dts-ES DECODING: AUTO DECODING: ON DECODING: OFF FILM & MODE ADJUST • @@@! L7 FILM OR FILM @@ L7 FILM Listening mode name differs depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. Refer to the previous page for more information. Parameter Default Setting Possible Settings VOCAL ENHANCE +0.0dB +6.0dB, +3.
MODE ADJUST JBL MUSIC & MODE ADJUST @@@! L7 MUSIC OR @@ L7 MUSIC • Listening mode name differs depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. Refer to page 5-22 for more information. • A proprietary listening mode. • Designed for enhanced playback of 5.1-channel dts, 5.1channel matrix-encoded dts-ES, or 6.1-channel discreteencoded dts-ES music sources. • Similar to the FILM listening mode, but specifically tailored for music sources.
MODE ADJUST SDP-40 • • Applies THX timbre matching to minimize timbre differences between the front and surround channels, which results in smoother sound movements between them. Recommended for home theaters with THX-certified speakers. • Default Setting Possible Settings RE-EQUALIZER ON ON, OFF LFE MIX +0.0dB -10.0 to +0.0dB AUTO AUTO, ON, OFF DECODING When THX Ultra2 decoding is engaged: • Parameter Applies adaptive de-correlation to increase the perceived width of the listening space.
MODE ADJUST JBL MUSIC MODE ADJUST & @@ @** MUSIC MODE ADJUST • Designed for playback of 5.1-channel dts music sources. • The MUSIC listening mode is not available unless both side and rear speakers are present. • • @@@* • Listening mode name differs depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. Refer to page 5-22 for more information. Applies ASA processing to signals sent to the rear speakers.
MODE ADJUST SDP-40 & MODE ADJUST 2-CHAN 5.1a @@@* 2-CHAN FILM MODE ADJUST • Designed for converting 5.1- or 6.1-channel dts(-ES) input signals into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.1- or 6.1-channel dts(-ES) input signals to the front speakers and the subwoofer. • Recommended for recording purposes. 5.1a L7 FILM • A proprietary listening mode. • Designed for enhanced playback of 5.1-channel analog film sources. • Derives seven channels from 5.
MODE ADJUST 5.1a JBL MUSIC MODE ADJUST 5.1a 5.1a L7 MUSIC MODE ADJUST • A proprietary listening mode. • Similar to the 5.1a FILM listening mode, but specifically tailored for music sources. • Designed for enhanced playback of 5.1-channel analog music sources. • Recommended for 5.1-channel analog music sources. Parameter Default Setting Possible Settings VOCAL ENHANCE +0.0dB +6.0dB, +3.0dB, +0.
MODE ADJUST SDP-40 Input Source Parameter Setting SURROUND EX: ON SURROUND EX: OFF 5.1-Channel Analog 5.1a 5.1a SurEX ULTRA2 • Designed for playback of 5.1-channel analog film sources. • Allows 7-channel playback of 5.1-channel analog sources without THX Surround EX encoding. • Applies THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters. Most films are mixed for movie theaters, and might sound too bright when played back in home theaters without re-equalization.
MODE ADJUST 5.1a JBL MUSIC MODE ADJUST 5.1a STANDARD 5.1a @** MUSIC MODE ADJUST 5.1a STANDARD • Designed for playback of 5.1-channel analog music sources. • Designed for playback of 5.1-channel analog sources. • The 5.1a MUSIC listening mode is not available unless both side and rear speakers are present. • Converts 5.1-channel analog input signals into digital audio for internal processing. • Applies ASA processing to signals sent to the rear speakers.
MODE ADJUST SDP-40 5.1a 2-CHANNEL MODE ADJUST 5.1a BYPASS 5.1a 2-CHANNEL MODE ADJUST 5.1a BYPASS • Designed for converting 5.1-channel analog input signals into 2-channel LOGIC7-encoded output signals. • Designed for playback of 5.1-channel analog sources, such as DVD-A or SACD players. • Sends downmixed 5.1-channel analog input signals to the front speakers and the subwoofer.
MODE ADJUST 2CH BYPASS MODE ADJUST 2CH BYPASS • Designed for playback of 2-channel analog sources. • Sends analog audio input signals to the Main Zone audio output connectors labeled Front L/R. These signals receive no internal processing. • The 2CH BYPASS listening mode is automatically activated whenever a 2-channel analog source is present and the MAIN ADV menu ANALOG BYPASS parameter is set to ON.
MODE ADJUST SDP-40 To toggle between the custom and factory-default versions of the selected listening mode: CUSTOM MODE ADJUST Listening Mode CUSTOM Opens the CUSTOM menu shown below, which can be used to compare custom and factory-default versions of the selected listening mode and to restore the factory-default version of the selected listening mode.
MODE ADJUST RESET MODE MODE ADJUST JBL (continued from page 5-33) Listening Mode CUSTOM RESET MODE 2. When RESET MODE message appears, press the arrow button to restore the factory-default version of the selected listening mode. Press the arrow button to close the message without restoring the factory-default version of the selected listening mode.
MODE ADJUST SDP-40 BASS ENHANCE ON, OFF Selecting the ON setting enhances stereo bass, which results in low-frequency reproduction that is less localizable and more realistic in the listening space. The effectiveness of the BASS ENHANCE parameter varies depending on room acoustics and the ability of the surround speakers to reproduce low frequencies. It is recommended to use front, side, or rear speakers that are capable of reproducing frequencies of 40Hz or lower.
MODE ADJUST JBL Listening Mode Menu Parameter Descriptions EFFECT LVL (continued from page 5-35) Adjusts the amount of effect applied to the listening mode. CTR WIDTH MIN, 1 to 6, MAX DECODING -12 to +6dB AUTO, ON, OFF Adjusts the center image. When MIN is selected, the center image is heard from just the center speaker. When MAX is selected, the center image is heard from just the front left and right speakers as a “phantom” center image.
MODE ADJUST SDP-40 • The STATUS menu includes an SB level meter when the DECODING parameter is set to ON and a 5.1-channel dts source is present or when the DECODING parameter is set to AUTO and a 5.1-channel matrix-encoded or 6.1-channel discrete-encoded dts-ES source is present. is available when Dolby Digital Surround EX decoding is not engaged. Refer to the DIGITAL EX & DIGITAL listening mode descriptions that begin on page 5-19 for more information.
MODE ADJUST JBL Listening Mode Menu Parameter Descriptions (continued from page 5-37) LFE The LISTENER POS parameter range might extend past the location of the front left and right speakers. OFF, -30 to +12dB Controls the output level of the Main Zone audio output connector labeled LFE. The OUTPUT LEVELS menu does not include the LFE parameter unless an LFE subwoofer is present.
MODE ADJUST SDP-40 OUTPUT LEVELS REAR DLY OFFSET Opens the OUTPUT LEVELS menu, which can be used to adjust output levels for the Main Zone audio output connectors labeled Center, Subwoofer L/R, LFE, Side L/R, and Rear L/R. Refer to page 5-32 for more information. Increases the perceived depth of the listening space by delaying the arrival time of rear speaker signals.
MODE ADJUST JBL Listening Mode Menu Parameter Descriptions (continued from page 5-39) SIZE 4 to 20 or 30m Adjusts listening space length within a 4 to 20 or 30m range (depending on the listening mode). Increase the size of the space to increase the reverb effect. The full parameter range might not be available depending on the BASS RT and MID RT parameter settings. CAUTION Setting the BASS RT, MID RT, or SIZE parameters to a high value may produce undesirable or damaging audio.
MODE ADJUST SDP-40 SURR ROLLOFF 500Hz to 20.0kHz, OFF Applies high-frequency attenuation control to the Main Zone audio output connectors labeled Side L/R and Rear L/R. This filter is only applied to output signals generated by the SDP-40. SURROUND DLY 0 to 15ms Increases the perceived depth of the listening space by delaying the arrival time of signals from the side and rear speakers. It is recommended to increase the setting when a greater sense of depth is desired in the listening space.
MODE ADJUST JBL Listening Mode Menu Parameter Descriptions (continued from page 5-41) SURROUND MIX -5 to +5dB Controls the relative level of surround channel information sent to the Main Zone audio output connectors labeled Front L/R. It is recommended to set this parameter to +2 or +3dB for all input sources. VOCAL ENHANCE +6.0dB, +3.0dB, +0.0dB Controls the level of dialog boost in the Main Zone audio output connector labeled Center.
6 Troubleshooting & Maintenance Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Restoring Factory-Default Settings . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting & Maintenance JBL TROUBLESHOOTING The SDP-40 is powered on, but there is no audio. The SDP-40 does not power on. 1. Examine the audio cables to ensure a solid connection between the SDP-40 and all associated power amplifiers. 1. Make sure the rear panel power switch is set to the|(“on”) position. 2. Attempt to deactivate standby mode with both the front panel and remote control standby buttons. 3.
Troubleshooting & Maintenance SDP-40 A humming sound is present in the audio. The SDP-40 is exhibiting erratic behavior. 1. If a cable TV connection is present, disconnect the cable from the wall outlet. If this eliminates the humming sound, a ground loop isolation device is required. Contact an authorized Lexicon dealer or the cable provider for assistance. 1. Set the rear panel power switch to the c (“off”) position. Wait 10 seconds. Then, set the rear panel power switch to the|(“on”) position. 2.
Troubleshooting & Maintenance JBL ROUTINE MAINTENANCE RESTORING FACTORY-DEFAULT SETTINGS The following routine maintenance should be performed on a periodic basis: When factory-default settings are restored, all parameters and user-defined values are restored to their factory-default settings. Before restoring factory-default settings, it is recommended to record user-defined settings. • • Clean the SDP-40 exterior surface with a soft, lint-free cloth.
Troubleshooting & Maintenance SDP-40 Note: The Mute button must be pressed within 2 seconds of deactivating standby mode. Otherwise, the "MUTE ON" message will appear on the on-screen and front panel displays. If this occurs, too much time has passed. Begin again with step 2. 5. Press the and arrow buttons to highlight the desired option. • Highlight the RESTORE DEFAULTS option to restore factorydefault settings.
A Appendix Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Menu Trees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5 Installation Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix JBL SPECIFICATIONS Audio Input & Output Connectors Main Zone Audio Performance Analog Audio Inputs • 8 stereo (RCA) or 5 stereo and one 5.1-channel connectors THD + Noise • Below 0.
Appendix SDP-40 Zone 2 & Record Zone Audio Performance (continued) Composite & S-video Performance (continued) Signal-to-Noise Ratio • 105dB minimum, 108dB typical, 22kHz bandwidth Input Return Loss • >40dB Input Sensitivity • 200mVrms (4Vrms for maximum output level) Differential Gain • <0.5% Input Impedance • 100kΩ in parallel with 150pF Differential Phase • <0.
Appendix Specifications JBL (continued from page A-3) DECLARATION OF CONFORMITY Other Trigger Outputs • 1 power on/off and 2 programmable connectors on detachable screw terminals (+12 VDC, 0.5 amps each) RS-232 Serial Input/ Output • 2 9-pin D-sub connectors Power Requirements • 90-250 VAC, 50-60Hz, 90W (universal line input), detachable power cord SDP-40 Dimensions & Weight • Height (with feet): 5.
Appendix SDP-40 MENU TREES MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX REAR PANEL CONFIG 8 STEREO INPUTS OR 5 STEREO & 5.1 ANLG 8 STEREO INPUTS FOR REAR PANEL CFG 5 STEREO & 5.
TRIGGER 2 REMOTE ONLY DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX ZONE2 INPUTS RECORD INPUTS FILM TV MUSIC MUSIC SURR PLII + PLII MOVIE PLII MUSIC PRO LOGIC FILM MUSIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC 5.1 SurEX 5.1 MUSIC DIGITAL EX 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM MUSIC R R MUSIC 2-CHAN 5.1a FILM 5.1a MUSIC 5.1a SurEX 5.1a MUSIC 5.1a STANDARD 5.1a 2-CHANNEL 5.
Appendix SDP-40 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP DVD1 INPUT NAME EDIT INPUT NAME RESTORE DEFAULT NAME PRESS MENU V TO RESTORE INPUT NAME EDIT INPUT NAME DVD-1 ^ W Y BUTTONS TO EDIT UP TO 8 CHARACTERS V BUTTON TO ADVANCE DVD1 DIGITAL IN COAX-1 COAX-2 COAX-3 COAX-4 COAX-5 COAX-6 OPTICAL-1 OPTICAL-2 OPTICAL-3 OPTICAL-4 OPTICAL-5 OPTICAL-6 AES/EBU NONE SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS DVD1 ANALOG IN ANALOG-1 ANALOG-2 ANALOG-3 ANALOG-4 ANALOG-5
Appendix Menu Trees JBL (continued from page A-7) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS DVD1 MAIN ADV INPUT SELECT DIGITAL ANALOG BYPASS OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD ON SAT MAIN ADV INPUT SELECT ANALOG BYPASS S-VIDEO 16:9 S-VIDEO OSD 4:3 COMPONENT OSD DVD2 MAIN ADV INPUT SELECT DIGITAL ANALOG BYPASS OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD ON VCR MAIN ADV INPUT SELECT AN
Appendix SDP-40 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R SR 40Hz RR 60Hz 60Hz C 60Hz M SUB 40Hz CUSTOM SETUP FRONT L/R 40Hz CENTER 60Hz SIDE L/R 60Hz REAR L/R 60Hz SUB L/R MONO SUB XOVER 40Hz LFE OFF ULTRA2 SUB OFF BGC N/A ASA APART FRONT L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz CENTE
Appendix JBL MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRAITON R SR +0.0dB LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITERS RR +0.0dB +0.0dB C +0.0dB M SUB +0.0dB SPEAKER DISTANCES FRONT LEFT 0.0ft CENTER 0.0ft FRONT RIGHT 0.0ft SIDE RIGHT 0.0ft REAR RIGHT 0.0ft REAR LEFT 0.0ft SIDE LEFT 0.0ft MONO SUB 0.
Appendix SDP-40 Menu Trees (continued from page A-10) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP MODE ADJUST FILM TV MUSIC MUSIC SURR PLII + PLII MOVIE PLII MUSIC PRO LOGIC FILM MUSIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC 5.1 * 5.1 MUSIC DIGITAL* 5.1 2-CHANNEL 5.1 MONO LOGIC 5.1 MONO SURR 5.1 MONO FILM* MUSIC* * MUSIC * 2-CHAN* 5.1a FILM 5.1a MUSIC 5.1a * 5.1a MUSIC 5.1a STANDARD 5.1a 2-CHANNEL 5.
Appendix JBL PARTY OUTPUT LEVELS CUSTOM 2-CHANNEL SUB L/R LVL CUSTOM +0dB MONO LOGIC EFFECT LVL -9dB ACADEMY FILTER ON SURR ROLLOFF 3.1kHz OUTPUT LEVELS CUSTOM MONO SURROUND OUTPUT LEVELS CUSTOM MONO SUB L/R LVL CUSTOM +0dB 5.1 FILM VOCAL ENHANCE +0.0dB 5 SPKR ENHANCE ON BASS ENHANCE OFF RE-EQUALIZER ON REAR DLY OFFSET 15ms COMPRESSION OFF LFE MIX +0.0dB OUTPUT LEVELS CUSTOM A-12 5.1 TV VOCAL ENHANCE +0.
Appendix SDP-40 Menu Trees (continued from page A-12) Selecting the listening mode menu CALIBRATION, OUTPUT LEVELS, or CUSTOM option opens the corresponding menu shown below. The CALIBRATION option is available for the PANORAMA listening mode. The OUTPUT LEVELS and CUSTOM options are available for most listening modes. These menus are identical regardless of which listening mode is selected. Listening mode menu parameter drop-down menus are shown below and on the next page.
Appendix JBL INPUT BALANCE L< <|> MASTER LEVEL >R LFE MIX -5 to +5dB MID RT LISTENER POSITION +0 +127 LIVENESS ON OFF PRE-DELAY 30ms to 20.2s LOW FREQ WIDTH -25 to +25dB A-14 24ms to 24.3s PANORAMA RE-EQUALIZER ON OFF SPEECH DETECT SOUND STAGE RESET MODE PRESS RIGHT V TO RESTORE MODE 500Hz to 20.
JBL SDP-40 Menu Trees (continued from page A-14) FACTORY SETTINGS EXIT RESTORE DEFAULTS FACTORY SETTINGS HAVE BEEN RESTORED PRESS ANY KEY TO RESTART Pressing and holding the Mute button while the SDP-40 is activated opens the FACTORY SETTINGS menu shown at the left, which can be used to restore factory-default settings. When the Shift command bank is activated, pressing the STAT button opens the status menu for the current input source.
Appendix JBL INSTALLATION WORKSHEET INPUT SETUP NAME DIGITAL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2-CH D 5.
Appendix SDP-40 Installation Worksheet SPEAKER SETUP FRONT L/R (continued from page A-16) CUSTOM SETUP SYNTHESIS 7CH SETUP 1 2 LEVELS CALIBRATION 80Hz CENTER 80Hz SIDE L/R 1 2 80Hz REAR L/R 1 2 80Hz 1 2 3 80Hz SUB L/R SPEAKER DISTANCES SUB XOVER 80Hz LFE OFF ULTRA2 SUB BGC ASA UNITS BASS PEAK LIMITERS CAL NOISE L/R LIMITER L/R LIMIT ADJ LFE LIMITER LFE LIMIT ADJ REAR PANEL CONFIG Circle one. 8 STEREO INPUTS 5 STEREO & 5.
Appendix DISPLAY SETUP ON-SCREEN DISPLAY STATUS POSITION FORMAT BACKGROUND REMOTE STATE FRONT PANEL DISPLAY STATUS BRIGHTNESS A/V SYNC DELAY CUSTOM NAME EDIT CUSTOM NAME AUDIO CONTROLS BASS TREBLE TILT EQ LOUDNESS JBL TRIGGER 1 SETUP Circle all parameters set to ON.
I Index SYMBOLS & LOGOS Documentation Conventions, ii , see Dolby , see also dts, dts-ES, dts(-ES) R , see dts Neo:6 NUMBERS (continued) 5.1 MUSIC Listening Mode, 5-4, 5-16, A-12 (menu ill.) 5.1 NUMBERS (continued) 7/5 Button, 2-16 8 STEREO INPUTS Option, 3-41, A-5 TV Listening Mode, 5-4, 5-16, A-12 (menu ill.) 5.1 MONO Listening Mode, 5-22, A-12 (menu ill.) A 5.1 MONO LOGIC Listening Mode, 5-21, A-12 (menu ill.) A/V SYNC DELAY Parameter, 3-42, A-5 , see LOGIC7 5.
Index A (continued) C AUTO Parameter, 3-8 to 3-9, A-7 CHURCH Listening Mode, 5-11, A-11 (menu ill.) B BACKGROUND Parameter, 3-44, 3-45, A-5 BALANCE Parameter, 4-2, 4-7, A-10 D (continued) (continued) DISPLAY SETUP Menu, 2-11 (ills.), 3-2, 3-59 to 3-63 (ills.
E EDIT CUSTOM NAME Option, 3-42, 3-43, A-5 EDIT INPUT NAME Option, 3-4 to 3-5 (menu ill.), A-7 EFFECT LVL Parameter, 5-10, 5-11, 5-12, 5-14, 5-21, 5-36, A-13 DECODING Parameter, 5-23, 5-24, 5-25, 5-26, 5-27, 5-36 to 5-37, A-13 ENCODING Parameter, 2-21, 2-23 EX DECODING Parameter, 5-20, 5-37, A-13 EX ENCODED Parameter, 2-21, 2-23 External Noise Test, 3-34, F Factory-Default Settings, Restoring, 6-4 to 6-5 FACTORY SETTINGS Menu, 6-4, A-15 (ill.
Index L M (continued) LOUDNESS Parameter, 4-2, 4-6 (frequency-response graph), A-10 MODE FAMILY SELECTION BUTTONS , 2-17, 5-4 , 2-17, 5-4 , 2-17, 5-4 MUSIC, 2-17, 5-4 , 2-17, 5-4 TVL, 2-17, 5-4 LOW FREQ WIDTH Parameter, 5-12, 5-38, A-11 MODE Parameter, 2-20, 2-21, 2-22, 2-23 Lowpass Filter, 3-23 (ill.) MODES Parameter, 3-50, A-5, A-20 FILM Listening Mode, 5-4, 5-5, A-11 (menu ill.) MUSIC Listening Mode, 5-4, 5-6, A-11 (menu ill.) MUSIC SURR Listening Mode, 5-7, A-11 (menu ill.
P R (continued) PARAMETERS Preferred Listening Mode Selection, 5-3 Selecting, 2-11 to 2-12 POSITION Parameter, 3-44, 3-45, A-5 Power Switch, 2-5 PRE-DELAY Parameter, 5-10, 5-11, 5-39, A-14 Preferred Listening Mode Selection Parameters 2-CH Parameter, 3-11, 3-12 to 3-13 (menu ill.), 5-3, A-7 (menu ill.) D Parameter, 3-11, 3-12 (menu ill.), 3-13, 5-3, A-7 (menu ill.), A-11 Parameter, 3-11, 3-12 (menu ill.), 3-13, 5-3, A-7 (menu ill.), A-12 5.1a Parameter, 3-11, 3-12 (menu ill.), 3-13, 5-3, A-7 (menu ill.
Index S (continued) SPEAKER SETUP Menu, 3-2, 3-21 to 3-40 (ills.), A-5 (ill.), A-9 to A-10 (ills.) SPEAKER SETUP PARAMETERS ASA, 3-25, 3-31 to 3-32, A-9, BGC, 3-25, 3-31, A-9 CENTER, 3-25, 3-26 (menu ill.), 3-27, A-9 (menu ill.), A-20 FRONT L/R, 3-25, 3-26 to 3-27 (menu ill.), A-9 (menu ill.) LFE, 3-25, 3-30, A-9, A-10 REAR L/R, 3-25, 3-26 (menu ill.), 3-28 (menu ill.), A-9 (menu ill.) SIDE L/R, 3-25, 3-26 (menu ill.), 3-27, A-9 (menu ill.), A-10 SUB L/R, 3-25, 3-26 (menu ill.), 3-29, A-9 (menu ill.
SYNTHESIS LIMITED WARRANTY The JBL Synthesis products listed below are warranted for the period stated from the date of original purchase: Amplifiers, Equalizers, and Surround Sound Processors – two (2) year warranty. Who is protected by this warranty? Your JBL warranty protects the original owner and all subsequent owners, so long as the original bill of sale is presented when warranty service is requested.
JBL SIS Products Group 8500 Balboa Boulevard Northridge, CA 91329 250 Crossways Park Drive Woodbury, NY 11797 800-336-4JBL Part No.