VMA Series VMA160 VMA1120 VMA1240 VMA260 VMA2120 Commercial Series 1 Channel & 2 Channel Mixer-Amplifier Operation Manual MASTER 1 2 VMA 160 3 4 MUSIC USB 1 MASTER 1 1 VMA 260 2 3 1 MUSIC 1 4 4 5 6 MASTER 2 MUSIC 2 USB
Contents Important Safety Information ������������������������������������������������������������������������������������������������������������������������������3 Declaration of Conformity ����������������������������������������������������������������������������������������������������������������������������������5 1.0 Welcome �������������������������������������������������������������������������������������������������������������������������������������������������������7 1.
IMPORTANT SAFETY INFORMATION WARNING FOR YOUR PROTECTION READ THESE INSTRUCTIONS: WARNING KEEP THESE INSTRUCTIONS RISK OF ELETRIC SHOCK DO NOT OPEN AVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR WARNING: TO THE REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE Thesymbolsshownaboveareinternationallyacceptedsymbols thatwarnofpotentialhazardswithelectricalproducts.
IMPORTANT SAFETY INFORMATION U.K. MAINS PLUG WARNING A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUMSTANCESSHOULDYOUINSERTADAMAGEDORCUTMAINSPLUG INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your localretailer. Replacementfusesare13ampsandMUSTbeASTAapproved to BS1362.
EU - DECLARATION OF CONFORMITY Manufacturer: Harman International 8500 Balboa Blvd, Northridge, CA 91329 USA Phone +1.818.893.
SUPPLIER DECLARATION OF CONFORMITY (SDoC) Company: Address: Telephone: Model names: Harman Professional 3000 Research Dr. Richardson, Tx 75082 800.222.0193 VMA160, VMA1120, VMA1240, VMA260, VMA2120 1 Channel & 2 Channel Mixer-Amplifiers We, Harman International, declare that the SDoC is issued under our sole responsibility and belongs to the following prod VMA160,VMA1120,VMA1240,VMA260,VMA2120 1 Channel & 2 Channel Mixer-Amplifiers.
1.0 Welcome The JBL® VMA Series of Mixer-Amplifiers are professional tools designed and built for Installed sound applications. There are both single channel and two channel models with five or eight mixer channels, respectively. They provide mixer capability with independent level control for each input channel and amplification with a choice of low impedance, 70V or 100V outputs. The product includes a rack mounting kit for installations to a cabinet.
1.2 Front Panel Controls & Indicators A B C D MASTER E 1 2 VMA 160 3 4 MUSIC USB 1 F H G I J Figure 1.2.1 Front Panel, 1 Channel Model A. Input Level Controls B. Media Player Display C. Output Volume Control(s) Including an Illuminated ring around the output volume control will light green with signal presence while red indicates clipping, i.e. the signal has reached the threshold of audible distortion D. Power Switch E. Power on LED illuminates blue when power is switched on. F.
1.3 Rear Panel Controls & Connectors (VMA160, VMA1120, VMA1240) A B D C WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVERTISSEMENT - RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR. AVERTISSEMENT - ÉNERGIE ÉLECTRIQUE DANGEREUSE VOIR LA NOTICE DE FONCTIONNEMENT.
1.4 Rear Panel Controls & Connectors (VMA260 & VMA2120) A B Apparatet må tilkoples jordet stikkontakt Apparaten skall anslutas till jordat uttag Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN OUTPUTS CAN-ICES-3(B)/NMB-3(B) C THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
2.0 Setup 2.1 Unpacking Your Amplifier Please unpack and inspect your amplifier for any damage that may have occurred during transit. If damage is found, notify the transportation company immediately. Only you can initiate a claim for shipping damage. We will be happy to help as needed. Save the shipping carton as evidence of damage for the shipper’s inspection. We also recommend that you save all packing materials so you will have them if you ever need to transport the unit.
FRONT VIEW MASTER 1 MASTER 2 88.10 mm [3.47 in] 1 VMA 260 2 3 1 MUSIC 1 4 5 6 MUSIC 2 USB 4 432.00 mm [17.00 in] SIDE VIEW 401.00 mm [15.79 in] Figure 2.2.1 Dimensions Front Angle Brackets Rear Angle Brackets Rear Flat Brackets Figure 2.2.
Figure 2.2.3 Rack Mounting the Mixer-Amplifier To install, refer to Figure 2.2.3 and follow the steps below: 1. Attach the front angle brackets to each side of the front of the amplifier using the screws provided. 2. Attach the rear flat brackets to each side of the rear of the amplifier with the screws provided. 3. Install the unit into the cabinet using the rack mount screws through the front angle brackets.
2.3 Ensuring Proper Cooling When using an equipment rack, keep a minimum space of 4 inches (10 cm) from the top surface of the unit. Close any open spaces in the rack with blank panels. DO NOT block any air vents. The side walls of the rack should be a minimum of 2 inches (5 cm) from the amplifier sides. The back of the rack should be open. 2.
2.5 Output Wiring & Connectors To drive distributed speaker systems designed to operate at 70V or 100V, connect to the corresponding output terminals. JBL recommends using pre-built or professionally wired, high-quality, two-conductor, heavy gauge speaker wire. Speaker wires should be twisted cable, if possible. To prevent the possibility of short-circuits, the wires should be stripped back no greater than 6 mm (1/4 inch), see Figure 2.5.1.
2.6 Wiring Your Audio System WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVERTISSEMENT - RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR. AVERTISSEMENT - ÉNERGIE ÉLECTRIQUE DANGEREUSE VOIR LA NOTICE DE FONCTIONNEMENT.
2.7 Connecting to AC Mains Connect your amplifier to the AC mains power source (power outlet) with the supplied AC power cord. First, connect the IEC end of the cord set to the IEC connector on the amplifier; then, plug the other end of the cord set to the AC mains. When properly connected to a live power source, the power LED should illuminate blue. WARNING: The third prong of this connector (ground) is an important safety feature.
3.0 Operation 3.1 Precautions Your amplifier is protected from internal and external faults, but you should still take the following precautions for optimum performance and safety: 1. Before use, your amplifier first must be configured for proper operation, including input and output wiring hookup. Improper wiring can result in serious operating difficulties. For information on wiring and configuration, please consult the Setup section of this manual. 2.
3.2 Input Routing The two-channel models, VMA260 and VMA2120, include a default routing of Input channels 1-3, Music 1 and the Bluetooth/USB source to amplifier 1. Input channels 4-6 and Music 2 are routed to amplifier 2. The user may take any input and have it routed to both outputs by selecting the appropriate switch. For example, if you set switch 1 to ON, Input 1 will be routed to both AMP1 and AMP2. 3.
3.4 VOX Function Voice activated ducking is available on input channel 2 of the VMA160, VMA1120 and VMA1240. The feature is available for both input channels 2 and 5 of the VMA260, and VMA2120. The audio input level required to activate ducking is set using the trim pot on the rear panel. Adjusting in the counterclockwise direction will reduce that level while the full clockwise setting will disable the VOX function. 3.
3.7 Media Player 3.7.1 Bluetooth Operation To activate Bluetooth, perform the following: 1. Press the Bluetooth Key until the Bluetooth Indicator begins to flash. 2. Enable Bluetooth of your source media player and search for “JBL COMMERCIAL (XX)”. Establish a connection. (Note that the “XX” represents the last two digits of the MAC address which allows the user to have multiple systems in close proximity.) 3. Once connected, the Bluetooth Indicator will stop flashing and remain illuminated. 4.
• REPEAT ALL 60Min Message – Play the track with the predefined name, “MESSAGE_1.mp3” every 60 minutes while repeating all other tracks. • REPEAT OFF – No repeat. 5. Press the PLAY/PAUSE key to pause or resume playing. 6. Press the STOP key to stop playing. 7. Press the PREVIOUS Key once to jump to the beginning of the current track or twice to the previous track. 8. Hold down the PREVIOUS Key to rewind. 9. Press the NEXT Key to jump to the beginning of the next track. 10.
4.0 Troubleshooting CONDITION: No power to the mixer-amplifier so that the power LED is not illuminated. POSSIBLE REASON: The mixer-amplifier is not plugged into the power outlet. CONDITION: No sound or low sound. POSSIBLE REASON: The input signal is not present or at a very low level. POSSIBLE REASON: The Master Volume control is turned down. POSSIBLE REASON: A CSR-V is connected and turned down. POSSIBLE REASON: Mixer channel inputs are turned down.
Appendix A: Preliminary Performance Specifications Performance Max Output Power per Channel into 4 Ω or 8 Ω; 1kHz, ≤ 0.
Appendix B: Block Diagrams VMA260 & VMA2120 TO CH2 Input 1 Mic/Line [1/4" Bal] +27V TO CH2 Input 2 Mic/Line [Bal] 1/4" Bal Input 2 PTT VOX +27V TO CH2 Input 3 Mic/Line [Bal] Summed RCA TO CH2 Music 1 Line [Summed RCA] TO CH2 BT/USB *CH1_BT_SW* Control: - Chime CH2 ON/OFF - Input 5 PTT Input 4 Input 4 to Ch 1 Input 5 to Ch 1 Input 6 to Ch 1 Attenuation (VOX/PTT) Input 5 Input 6 CH1_PRIORITY Music 2 Music 2 to Ch 1 TO CH1 Input 4 Mic/Line [1/4" bal] *CH2_CTRL_1* Control: - Input 1 to Ch 2
VMA260 & VMA2120 Continued Hi-Z Switch OUTPUT TRANSFORMER (CH 1) 100V 70V COMMON TONE CONTROL SPI CLIP VCA HPF POWER AMP + MASTER VOLUME REMOTE VOLUME Feedback CRYSTAL SDRAM MCU DAC BT/USB FLASH BT MODULE MCU SECTION Hi-Z Switch OUTPUT TRANSFORMER (CH 2) 100V 70V COMMON TONE CONTROL SPI CLIP HPF VCA MASTER VOLUME REMOTE VOLUME Feedback 26 POWER AMP +
VMA160, VMA1120 & VMA1240 Input 1 Mic/Line [1/4" Bal] +27V Input 2 Mic/Line [Bal] Input 2 PTT VOX Input 3 Mic/Line [1/4" Bal] +27V Input 4 Mic/Line [Bal] Summed RCA Attenuation (VOX/PTT) Music Line [Summed RCA] BT/USB CH1_PRIORITY Hi-Z Switch OUTPUT TRANSFORMER 100V 70V COMMON TONE CONTROL SPI CLIP HPF VCA POWER AMP + MASTER VOLUME REMOTE VOLUME Feedback CRYSTAL SDRAM MCU DAC BT/USB FLASH BT MODULE MCU SECTION 27
Appendix C: Contact Information For additional information, please consult JBL Professional Customer Service, your system installer or retailer. On The World Wide Web: www.jblcommercialproducts.com Professional Contacts, Outside the USA: Contact the JBL Professional Distributor in your area. A complete list of JBL Professional international distributors is provided at our U.S.A. Website: www.jblpro. com.
JBL Commercial 3000 Research Dr.