Gateway 900 Installation Manual
NOTICE Specifications described in this manual are subject to change without notice. Revision Level: 5.0 Revision Date: 1/3/2004 © Copyright 2004 by JBM Electronics Co. For further information, contact: JBM Electronics Co. 4645 LaGuardia St. Louis, MO 63134 (314) 426-7781 Fax: (314) 426-0007 Website: © JBM Electronics Co. http://www.jbmelectronics.com 1-800-489-7781 www.jbmelectronics.
Gateway 900 Installation Manual Page 1 Overview JBM Electronics' Gateways are low-cost routers designed for users who need to interface Legacy protocol devices to a Frame Relay network. The Gateway 900 (G900) provides one serial port, a 10/100BaseT port and a WAN port with an integrated T1/E1 DSU Converts data from a TCP/IP device to UDP for Ethernet networks. The Gateways convert Legacy protocols to TCP/IP or UDP for connection to a Frame Relay network.
Gateway 900 Installation Manual Page 2 Benefits The Gateway simplifies network design by eliminating the need for network changes to handle Legacy protocols. The conversion eliminates the need for a separate network for the legacy protocol and protects the investment in Legacy devices when moving to an IP network. The Gateway can help protect the investment in Legacy devices when moving to a new network.
Gateway 900 Installation Manual Page 3 Diagnostics The Gateways can be configured through Application Commands entered via Telnet interface. The Telnet connection provides command and control of the Gateway. SNMP Traps provide notification of major events in the Gateway. All of the protocol-specific diagnostics, such as LUSTATS, Notify, and Status and Sense Bytes are supported. Extensions to the Telnet or SNMP commands are available as a special order.
Gateway 900 Installation Manual Page 4 The Gateways can be ordered with Frame Relay connections using an internal or external DSU. The Gateway 700 provides the same port configuration as the G900 but uses an external DSU. The Gateway 800 provides an integrated 56/64/72 KB DSU. With the frame connection, the Gateways provide a complete router replacement with full protocol conversion.
Gateway 900 Installation Manual Page 5 Installation The manuals used with the Gateways are: Manual Installation Setup Operations Cables Usage Unpacking and installing the Gateway Defining the Gateway’s configuration Controlling the Gateway Cable Wire Lists The Setup and Operations Manuals are on the CD supplied with the Gateway. 1. Remove the JBM Electronics Gateway 900 from the shipping carton. 2. Inspect the Gateway for shipping damage.
Gateway 900 Installation Manual Page 6 AVERTISSEMENT: Points d’accès RJ-45. Ceux-ci sont protégés par des prises de données. Ils ne peuvent pas êntre utilisés comme prises de téléphone conventionnelles standard, ni pour la connection de l’unité à un réseau téléphonique central privé ou public. Raccorder seulement connecteurs de données RJ-45, systèmes de réseaux de téléphonie ou téléphones de réseaux à ces prises.
Gateway 900 Installation Manual Page 7 Operation The Gateways are designed for unattended operation. The Gateways can be controlled through the Console Port (Port 5) or via Telnet (if the Gateway’s IP Address is known). The connection provides access through a variety of Application Commands. The JBM Operations Manual provides further information on the operation of the Gateway, including Command Line instructions, JBM Administrative Menu and other features.
Gateway 900 Installation Manual 3. Page 8 The Gateway will display the Login Screen. Screen 1 – Initial Login Screen 4. Once this screen is displayed, Log in to the Gateway using root for the user name and gateway for the password. These entries are case sensitive and must be entered in the appropriate case. This userid and password is used for Console and Telnet access. Note: We recommend you change password using the instructions in the Gateway Operations Manual.
Gateway 900 Installation Manual Page 9 Configure the WAN interface Instructions for configuring the WAN interface are available through the console: - Readme.config (configuring IP over frame) Wanpipe Configuration.pdf (general overview) Wanpipe Configuration Before starting WANPIPE, a configuration file (wanpipeN.conf, where N=1,2,3..etc.) must be created in /etc/wanpipe directory. This file contains the line, hardware and interface definitions for the WAN connection.
Gateway 900 Installation Manual Page 10 For the rest of this document, we will assume we are working with the following ISP/Telco supplied data: Protocol: Prot Info: IP Info: Frame Relay Num of DLCI's = 2 DLCI=16 and 17 LCI 16 Local =201.1.1.1 PtoP =201.1.1.2 Netmask =255.255.255.0 Gateway =201.1.1.2 (i.e. this is the system default gateway) DLCI 17 Local =202.1.1.1 PtoP =202.1.1.2 Netmask =255.255.255.0 Gateway =N/A WANCFG 1. Start /usr/sbin/wancfg 2. Select 'Create' option 3.
Gateway 900 Installation Manual Page 11 This example is Frame Relay with two DLCIs. The first input is: "Please specify the number of DLCIs supported on this Frame Relay connection" Enter in number 2 For each network interface do the following: - DLCI Number: Enter in the DLCI number. Note the default number is always 16. - Interface Name: The Interface name will also have default value. You can leave it as is or change it. For instance, you could change it to ?chicago? or ?toronto?.
Gateway 900 Installation Manual Page 12 Thus if errors occur, first check /var/log/messages to find out what exactly went wrong with the drivers startup. Once the device is started you should see a "link connecting" message. This message indicates that the card was been configured successfully and that the link is trying to connect. Reset Function The Gateways have a Reset Button that can be used to perform the following function: Function Restart Action Press and release the switch.
Gateway 900 Installation Manual Page 13 Gateway 900 Specifications Serial Port: WAN Port: LAN Port: Console Port: Management: LED Indicators: Power: Physical: Processor: Memory: Warranty: © JBM Electronics Co. Baud Rate: Interface: 110-56,000 bps One Female DB-25 connector RS-232C/V.
Gateway 900 Installation Manual Page 14 SAFETY INFORMATION Please read the following safety information carefully before installing the Gateway. WARNING: Installation and removal of the unit must be carried out by qualified personnel only. The unit must be connected to an earthed (grounded) outlet to comply with international safety standards. Do not connect the unit to an A.C. outlet (power supply) without an earth (grounded) connection.
Gateway 900 Installation Manual Page 15 UK The supply plug must comply with BS1363 (3-pin 13-amp) and be fitted with a 5 A fuse which compiles with BS1362. The main cords must be or marked and be of type HO3VVF3G0.75 (minimum). Europe The supply plug must comply with CEE7/7 (“SCHUKO”) The main cords must be or marked and be of type HO3VVF3G0.75 (minimum).
Gateway 900 Installation Manual Page 16 Danemark La prise mâle d’alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a. Suisse La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011. Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”) Le cordon secteur doit porter la mention ou et doit être de type H03VVF3GO.75 (minimum).
Gateway 900 Installation Manual Page 17 Information To The User If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient the receiving antenna. Relocate the equipment with respect to the receiver. Move the equipment away from the receiver.
Gateway 900 Installation Manual Page 18 Except for the express warranty set forth herein, JBM Electronics Co. grants no warranties, either express or implied, of merchantability and fitness. The stated express warranty is in lieu of all liabilities or obligations of JBM Electronics Co. for damages including but not limited to consequential damages occurring out of or in connection with the delivery, use or performance of JBM products.
