TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Warnings And Cautions . . . . . . . . . . . . . . . . . . 7 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . 7 m How To Use This Manual . . . . . . . . . . . . . . . . . 6 m Vehicle Modifications / Alterations . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeept Wrangler and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle. Before you start to drive this vehicle, read the Owner’s Manual.
INTRODUCTION 5 Although your vehicle may be equipped with a soft top or optional hard top to give the occupants protection from the weather, these tops do not offer structural protection in the event of an accident and do not change the open-body characteristic of the vehicle. Even though your vehicle has a sport bar and side bars for some extra protection, it is a truly open vehicle-there is no structural integrated top and it has low sides and a folding windshield.
INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . .11 m Illuminated Entry — If Equipped . . . . . . . . . . .15 ▫ Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . .11 m Doors And Locks . . . . . . . . . . . . . . . . . . . . . . .15 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .15 m Sentry Key Immobilizer System — If Equipped . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .40 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . .41 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. 11 To remove the ignition key on models with an automatic transmission, place the gearshift lever in P (Park), turn the ignition key to LOCK, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. CAUTION! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. SENTRY KEY IMMOBILIZER SYSTEM — IF EQUIPPED The Sentry Key Immobilizer System (SKIS) prevents unauthorized operation of the vehicle by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 • Mobil Speedpass™, additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (Transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Also, cell phones, pagers, or other RF electronics will not cause interference with this system. At the time of purchase, the original owner is provided with a four digit PIN number.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds, a chime will sound and the SKIS indicator light will begin to flash. Turn the ignition switch OFF and remove the second key. 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound. The SKIS indicator light will stop flashing, turn on for 3 seconds; then turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY — IF EQUIPPED The interior lights will come on when you open any door. The lights will remain on after all of the doors are closed, and then fade to off or they will immediately fade to off once the ignition switch is turned on. DOORS AND LOCKS NOTE: The ignition key that is used to start the vehicle is used to lock or unlock the doors, tailgate, console storage, and glove box. To unlock doors and tailgate insert the key and turn.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt cannot do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you cannot straighten a belt in your vehicle, take it to your dealer and have it fixed. WARNING! 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt anchorage can be adjusted upward or downward to position the belt away from your neck. Push in on the anchorage near your outside shoulder and slide it up or down to reach the position that serves you best. 21 Seat Belts And Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and stow the seat belt extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Also, the ACM turns on the “Airbag Warning Light” in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. If the ACM detects a malfunction, the “Airbag Warning Light” will illuminate for a minimum of 12 seconds and will remain illuminated as long as the malfunction exists.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch — If Equipped NOTE: The Passenger Airbag ON/OFF Switch is designed so that the switch position can be changed using the ignition key. The key inserts into the switch far enough to fully depress a spring-loaded locking plunger, and then rotates to the desired position. The key will not insert fully into the switch, and the spring-loaded locking plunger prevents the key from remaining in the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Shut Off the Passenger Airbag 1. Turn ignition to OFF position. 2. Remove the water-resistant plug. 3. Place the ignition key in the Passenger Airbag ON/ OFF Switch, press inward and turn the key to the right to the OFF position. This will shut off the passenger airbag. 4. Reinstall the water-resistant plug. NOTE: When the Passenger Airbag ON/OFF Switch is in the OFF position, a indicator light will illuminate when the ignition is ON.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. • It is not advisable to drive your vehicle after the airbags have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit in the vehicle’s seat belts properly. If the child cannot sit with knees bent over the seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer also recommends that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CH ildren) Your vehicle’s front passenger and two rear outboard (if equipped) seating positions are equipped with the child restraint anchorage system called LATCH.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger and rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind the front passenger and the rear seat (on the floor behind each rear outboard seating position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forwardfacing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the child’s face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Safety Checks You Should Make Inside The Vehicle Safety Checks You Should Make Outside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 ▫ Replacing The Rear Seat . . . . . . . . . . . . . . . . .54 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .46 m To Open And Close The Hood . . . . . . . . . . . . .55 ▫ Inside Automatic Dimming Compass/ Temperature Mirror — If Equipped . . . . . . . . .46 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 ▫ Compass Calibration . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights — Canada Only . . . . .58 m Electrical Power Outlet . . . . . . . . . . . . . . . . . . .63 m Windshield Wipers And Washers . . . . . . . . . . .58 ▫ Electrical Outlet Use With Engine Off . . . . . . . .63 ▫ Intermittent Wiper System . . . . . . . . . . . . . . . .58 m Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Windshield Wiper Operation . . . . . . . . . . . . . .59 m Storage . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 45 m Soft Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 ▫ Door Frame Installation . . . . . . . . . . . . . . . . . 101 ▫ Folding Down The Soft Top . . . . . . . . . . . . . . .84 m Folding Windshield . . . . . . . . . . . . . . . . . . . . 102 ▫ Putting Up The Soft Top . . . . . . . . . . . . . . . . .91 ▫ Lowering The Windshield And Removing Side Bars . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 47 Each time the center button is pressed and released within 3 seconds, the display toggles through the following three configurations: • display compass/temperature (Fahrenheit), • display compass/temperature (Celsius), • and display off. Compass Calibration CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the vehicle is new, the compass should initially be verified for correct compass variance (refer to Compass Variation Adjustment) and calibrated manually (refer to Manual Calibration). This will ensure correct initial calibration and eliminate initial erroneous compass headings. Manual Calibration If the compass appears erratic and CAL does not appear, you must manually put the compass into the calibration mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 49 To set the variance: Turn the ignition ON, and press and hold the center button for 3 to 6 seconds. The last variance zone number will be displayed. Each press of the center button will select a new variance zone. When the proper zone is selected, wait 5 seconds to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Vehicles and other objects seen in the right side convex mirror will look smaller and f arther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. • Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Front Seat Adjustment Move seat forward or rearward by lifting the lever. Be sure the latch engages fully.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 Tilting Front Seats Push the lever upward on the seatback to tilt the entire seat forward. 3 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold And Tumble Rear Seat To expand the cargo area: 1. Slide seat belts through the seat cushions into the cargo area. 2. Lift the seatback release lever and fold seatback forward. 3. Slowly flip the entire seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Secure the seat with the strap. Wrap strap around sport bar, and put one end of the strap through loop of the other end. Pull to tighten strap around sport bar. Place the opposite loop around hook of seat. Route the strap so that it is between the plates of the seat to eliminate slack and increase tension, as shown. 5. When completed, return seat to it’s normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • First fold the rear seat forward following steps 1 through 3 under “Fold and Tumble Rear Seat” in this section. • Press down on release bar on each side, and pull seat out and away from lower bracket. • Remove seat from the vehicle. Replacing the Rear Seat Reverse steps for removing the seat. Be certain to pull the seat belts between the seat cushion and seatback. Position them for passenger use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 TO OPEN AND CLOSE THE HOOD To open hood, first release both hood latches. 3 Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and radiator support and lift up on handle to raise hood. You may have to push down slightly on hood before lifting up on handle. Insert the support rod into the slot in the radiator support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. LIGHTS Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the muti-function control lever fully upward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Lights, Instrument Panel Lights, and Headlights Turn the end of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. 57 NOTE: If the driver’s door is left open, and the headlights or parking lights are left on, the “High Beam Indicator Light” will flash and a chime will sound.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Fog Lights — If Equipped The front fog light switch is in the multi-function control lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the end of the lever. Daytime Running Lights — Canada Only The headlights come on at a low intensity level after the vehicle has been driven approximately 3 feet (1 meter). They will turn off when the vehicle is turned off or when the headlights are switched on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE of the lever. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. Windshield Wiper Operation Move the lever upward to the second detent for LO speed wiper operation, or to the third detent for HI speed operation 59 Windshield Washers To use the washer, pull the lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back upwards to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory. Pressing the ON·OFF button or turning off the ignition erases the memory. To Resume Speed To resume a previously set speed, press and release the RESUME/ACCEL button. Resume can be used at any speed above 30 mph (50 km/h). To Activate Press and release the ON·OFF button to turn the system on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. (If the vehicle speed drops below 30 mph (48 km/h), the Speed Control will automatically disengage).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET To the right of the cigar lighter (if equipped) is the 12 volt power outlet. The outlet is connected directly to the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting. The outlet includes a tethered cap labeled with a battery symbol indicating the power source.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS In the center console there are two cup holders for the front seat passengers. NOTE: The cup holder insert is removable from the console, for cleaning. The rear passengers have cup holders at the rear of the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 STORAGE Glove Compartment To unlock the glove compartment, insert the key and turn. To open, pull the latch up. 3 Console Storage Compartment — If Equipped To unlock, insert key and turn. To open, press the latch button. Add-A-Trunk™ — If Equipped The factory-installed Add-A-Trunk™ option provides a secured compartment for parcels or equipment when the tailgate is closed and locked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the Add-A-Trunk™ is not desired, it can be easily removed from the rear compartment. Remove the four knobs that secure the “trunk” to the body. Lift the Add-A-Trunk™ out and place the knobs in the molded-in storage area. Storage space is also provided for the wheel lock, and lock key tool. Do not leave the Add-A-Trunk™ loose in your vehicle. Remove it and store it in a safe place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 4. Using a rubber mallet, carefully tap the knuckles from the outside edge. This will remove the bow assembly from the pivot bracket. Remove the soft top from the vehicle and store in a clean, dry location.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unzip the zipper on the sport bar cover to expose the pivot bracket. Remove the brackets using a #T40 Torxt head driver. Recover and re-zip the sports bar cover. Store pivot brackets and screws in a safe place. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (4) • right and left quarter windows • rear tailgate window. 2. Remove the hard top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 c. Lay the soft top back into the vehicle with the curved portion of the bows facing upward. CAUTION! d. Tap the knuckles on the side with a rubber mallet to reattach them to the pivot bracket. Do not overtighten the screws. You can strip the screws if they are overtightened. e. Screw the pivot screws back into place. Secure them until they are snug being careful not to crossthread the screws. 5. Unsnap and remove the black boot cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Open the tailgate. 7. Remove the tailgate bar (black bar with end caps) that is located in the soft top and set aside. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 8. Lift the soft top fabric up and away from the plastic header with latches. 9. Pull all of the soft top fabric toward the rear of the vehicle and wrap around the plastic header. 10.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. Move to the side of the vehicle and pull the side bow forward and down. You will see the 3 bow rise from the rear of the vehicle. 71 13. Unclip and move the sun visor to the side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Open the header latches and engage the hooks on each side into the windshield slot. NOTE: Do not latch at this time. 15. Grasp the drip rail retainers and untuck them from the door frame. The soft top fabric should cover the header completely from one side to the other. This may require you to pull some of the fabric down and around the corners. Repeat this step for the other side. NOTE: Do not tuck the drip rail retainers into the frame at this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow. Let them hang down over the sport bar. Make sure that the nylon check straps between the 2 bow and 3 bow are not twisted or wrapped around the 2 bow. NOTE: Do not tuck the sail panel retainers at this time. 73 17. Fold the rear seat back and sit in the rear cargo area, facing rearward. Look up at the 2 bow. Wrap fabric around 2 bow attaching it with the Velcrot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 18. Begin working from the rear tailgate opening and align the sail panel retainer to the edge of the body side retainer. Tuck the retainer around the corner working from back to front. NOTE: This may be difficult to do the first time. The fabric will stretch after the soft top is installed in the up position. 19. To install the quarter window, affix the rear corner of the quarter window temporarily to the Velcrot in the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 20. Tuck in the bottom retainers on the quarter windows into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 75 21. Locate the black retainer bar that was set aside. Remove and discard the end caps. Slide the retainer bar over the receiver at the bottom inside, with the bulky seal away from you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 22. Zip the rear window beginning from the left using both zipper ends. Leave one zipper end at the start. 23. Tuck in the retainer bar ends into the tailgate clips on each side of the tailgate opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 24. Tuck in the plastic retainers on each side of the rear window under the tailgate clips. 77 25. Tuck in the drip rail retainers into the rail slot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 26. Close the header latches and position the sun visor. HARD TOP CAUTION! • The hard top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! 79 3. Unbolt the six Torxt head screws which secure the hard top to the vehicle using a #40 Torxt head driver. Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed. 3 Hard Top Removal 1. Fold down the sun visors and move them to the side. 2. Unlatch the two hard top latches located at the top of the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: On a dual top vehicle, the two rear and center nuts are retained onto the bodyside. 4. Open both doors. 5. Open tailgate all the way to ensure clearance of the rear window glass. Lift rear window glass. 6. Locate the wiring harness at the rear left side corner of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Disconnect the washer hose and install the tethered cap. 81 NOTE: If the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected from the hard top. CAUTION! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system. 8.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the doors are to be removed, pull the #4 fuse from the fuse block to prevent dome lamp illumination. Hard Top Installation NOTE: If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. NOTE: The hard top must be positioned properly to ensure sealing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts. Folding Down The Soft Top 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the drip rail retainers and untuck both of them from the door frame slot. Repeat this on the other side. 85 4. Release the header latches and leave the hooks in the windshield slots. 3 3. Unclip and move the sun visor to the side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Open the tailgate, partially unzip the rear window on each side, and unlock the rear window retainers. NOTE: If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through Mopart distributors. 6. Pull the retainer bar straight out from the tailgate clips. • Remove the rear window entirely.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Beginning from the rear, moving forward, partially unzip the side window and untuck the bottom retainers. 87 8. Finish unzipping the window and repeat this step on the other side. NOTE: Stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the bodyside.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Remove Sunrider™ pins to release side rails from brackets located on both door rails (Unlimited Models Only). 12. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. 11. Release the hook portion of the latches. Grasp the side bow behind the header and lift the top back.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tuck the top between the 2 bow and the 3 bow as it folds. 89 14. Tuck the top between the 2 bow and the header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 15. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 16. After the top is folded down, the check straps must be wrapped around the header. This will keep them from hanging and flapping outside the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Putting Up The Soft Top NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 1. Slide Sunrider sleeve towards header to cover Sunrider link (Unlimited Models Only). 2. Begin working from the rear of the vehicle, with the tailgate open. Lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 91 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Unclip and move the sun visor to the side. 5. Open the header latches and engage the hook on each side into the windshield slot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Guide side bows down into bracket on door rails. Make sure door rail Sunrider pins engage into bracket on side bows (Unlimited Models Only). 7. Grasp the drip rail retainer and untuck them from the door frame. NOTE: Do not tuck the drip rails into the door frame at this time. 93 8. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow. Let them hang down over the sport bar.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Tuck the sail panel retainer into the bodyside retainer. Begin working from the rear tailgate opening and work to the corner. NOTE: This may be difficult to do the first time. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and push down to help tuck in the sail panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. To install the quarter windows, affix the rear corner of the window temporarily. Now, zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 95 11. After the door frame retainer has been completely tucked in, finish zipping in the window. Then affix the Velcrot flaps around the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. Tuck the bottom retainers on the quarter window into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 13. Zip in rear window beginning from the left using both zipper ends. Leave one zipper end at the start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. To assist in getting the zipper started, lay the bar on the inside of the wheel wells and uninstall half of the D-pillar retainer from U-rail to expose zipper ends. 97 15. Tuck the retainer bar into the tailgate clip.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Tuck in the solid plastic retainers on each side of the tailgate under the tailgate clip. 17. Tuck in drip rail retainers into the door frame slots.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 18. Close the header latches and return the sun visor to it’s original position. 99 SUNRIDER™ — IF EQUIPPED (UNLIMITED MODELS ONLY) To Raise 1. Grasp the drip rail retainers and untuck both of them from the door frame slot. Repeat this on the other side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Unclip and move the sun visors to the side. 3. Release the header latches, and slide the plastic sleeves forward. 5. Attach and reposition sunvisors. To Lower 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Secure latches to plastic retainer on header. Locate strap to secure the header to the sport bar. Wrap strap around sport bar and hook to header and tighten. 1. Remove strap from header and sport bar. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Tuck drip rail retainers into the door frame slots. 7. Close the header latches, and return sun visors to their original position. 101 2. Fold the door frames and store the knobs and door frames outside of the vehicle. Repeat this step for the other side. WARNING! DOOR FRAME WARNING! Do not drive your vehicle on-pavement with the door frame removed or the windshield down as you lose the protection these structural elements can provide.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Insert the top front of the door frame into the opening at the top corner of the door opening. Push the top rear of the door frame to the side bar. FOLDING WINDSHIELD The fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents. The windshield also provides some protection against weather, road debris and intrusion of small branches and other objects. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Before lowering windshield, disconnect the electrical connector for the inside Compass/Temperature mirror (if equipped). If required for certain off-road uses, the side bars can be removed and the windshield folded down. However, the protection afforded by these features is then lost. If you remove the side bars and fold down the windshield, drive slowly and cautiously.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Carefully follow these warnings to help protect against personal injury: • Do not drive your vehicle on-road with the windshield down. • Do not drive your vehicle unless the windshield is securely fastened, either up or down. • Eye protection, such as goggles, should be worn at all times when the windshield is down. • Be sure that you carefully follow the instructions for raising the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3. Remove the two Torxt head screws holding each side bar to the windshield frame. Shift the side bar inboard to clear windshield pillar molding when removing the side bar. 3 Do not loosen or remove the adjusting bolts on the side of the side bars. These bolts are set at the factory to properly fit the side bar to the vehicle. NOTE: Store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. To safely store the side bars in your vehicle, use four of the cinch straps, found in the glove box. Attach the straps through the footman loops located in the floor behind the folded rear seat on each side of the vehicle. WARNING! You or others could be injured if you carry the side bars loose in your vehicle. Remove the bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Remove the black round headed windshield Torxt head screw on each side of the base of the windshield. 107 8. Lower the windshield gently until it contacts the rubber hood bumpers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Secure the windshield by passing the remaining cinch strap, found in the glove box, through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising The Windshield And Replacing Side Bars To raise the windshield, install the windshield wipers, and install the side bars use these same steps in reverse.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel And Interior Controls . . . . . . 114 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 115 m Instrument Cluster Description . . . . . . . . . . . . 116 m Electronic Digital Clock . . . . . . . . . . . . . . . . . 120 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 121 m Radio General Information . . . . . . . . . . . . . . . 121 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 121 ▫ Two Types Of Signals . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ To Set The Radio Push-Button Memory . . . . . . 123 ▫ Operation Instructions — CD Player . . . . . . . . 128 ▫ Operating Instructions - RDS Mode . . . . . . . . 124 ▫ Inserting The Compact Disc . . . . . . . . . . . . . . 128 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 128 ▫ TA (Traffic Announcement) Button . . . . . . . . . 125 ▫ EJT CD (Eject) Button . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ To Set The Push-Button Memory . . . . . . . . . . 131 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 ▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 ▫ Bass And Treble Tone Control . . . . . . . . . . . . 131 ▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 132 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Cassette Player Features . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 m Satellite Radio — If Equipped . . . . . . . . . . . . . 145 ▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 143 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 145 ▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 145 ▫ EJT Tape . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 113 m Cassette Tape And Player Maintenance . . . . . . 148 ▫ Air Conditioning — If Equipped . . . . . . . . . . 151 m CD/DVD Disc Maintenance . . . . . . . . . . . . . . 149 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 154 m Radio Operation And Cellular Phones . . . . . . . 149 m Rear Window Features — Hard Top Only . . . . 154 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . 149 ▫ Rear Window Defogger . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND INTERIOR CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 115 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION Your vehicle is equipped with the instrument cluster described on the following pages. 1. Voltmeter Indicates available battery voltage and charging system operation. The lower red zone indicates that battery charge may be too low to start the engine. With the engine running, the normal operating range is between 11 and 15 volts.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. High Beam Indicator Light This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low. If the driver’s door is open, and the headlights or parklights are left on, the “High Beam Indicator Light” will flash and a chime will sound. 8. Seat Belt Indicator Light A warning chime and an indicator light will alert you to buckle the seat belts.
UNDERSTANDING YOUR INSTRUMENT PANEL 15. Coolant Temperature Gauge Indicates engine coolant temperature. The red zone to the far right indicates possible overheating. Seek authorized service immediately if the gauge operates in the red zone. In U.S. vehicles, temperature is indicated in degrees fahrenheit; in Canadian vehicles in degrees centigrade. 16. Airbag Warning Light This indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on.
UNDERSTANDING YOUR INSTRUMENT PANEL 19. Trip Odometer Button Press and release this button to toggle between the odometer and trip odometer displays. This button is also used to reset the trip odometer to 0. While the display is showing the trip odometer, press and hold the button for approximately 2 seconds and the display will reset to 0. 20. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL If the parking brake is applied and the vehicle is in motion, the red BRAKE warning light will “flash” and a chime will sound. The operation of the BRAKE warning light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Turn the ignition switch to the ON or ACC position and press the time button. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio. 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAD—AM & FM STEREO RADIO WITH GRAPHIC EQUALIZER, CASSETTE TAPE PLAYER WITH CD PLAYER To enter the code, turn the key to the ON or ACC position and press the ON/VOL control. The word CODE will appear on the display. Enter your four digit code by pressing the appropriate preset buttons in sequence. Your radio is now ready for basic operation. If an invalid code is entered into the radio, the radio will allow two more attempts.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the MW/LW or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 5 seconds after pressing the SET button, the station will continue to play, but will not be locked into push-button memory. Time Button Briefly press the Time button to change the display between radio frequency and time. You may add a second FM station to each push button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will appear in the radio display window. Each button can be set for SET 1 and SET 2 in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL TA (Traffic Announcement) Button Pressing the TA button will enable the Traffic Information system. If the current station does not have the TP function or is not a RDS station the radio will beep and display “NO TA” and then go into the TA seek mode. During Tape/CD mode the TA will give priority to traffic announcements from the last tuned TA station. TA mode is always off in the MW/LW mode. • Children During TA seek mode the radio display will flash “TA SEEK”.
UNDERSTANDING YOUR INSTRUMENT PANEL • Oldies • Other M • Phone In • Pop M • Religion • Rock M • Science • Social • Sport • Travel • Varied • Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation. Sometimes poor playback may be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year. Changing Tape Direction Press the top of the PTY button to change tape play direction. The display will confirm the selected tape play direction. The time is always displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL EJT CD (Eject) Button Press the EJT CD button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded, and the display will remain unchanged in whatever mode it is in. FF/TUNE/RW Button Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL make another selection. Holding the button will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency. If the button is pushed and held, the radio will continue to tune until the button is released. The frequency will be displayed and continuously updated while the button is pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player, CD changer, or the Satellite Radio (if equipped). When the Satellite Radio (if equipped) is selected “SA” will appear in your radio display.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 Time Button Press the time button to toggle between station frequency and time of day. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Pressing this button while playing a cassette tape will change the side of the tape being played.
UNDERSTANDING YOUR INSTRUMENT PANEL Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS 135 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL Bass and Treble Tone Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down increases or decreases amplification of that band. The mid position provides a balanced output. AM/FM Selection Press the AM/FM button to change from AM to FM.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! 137 If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
UNDERSTANDING YOUR INSTRUMENT PANEL Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. SALES CODE RBT/RBY—AM STEREO & FM STEREO RADIO WITH GRAPHIC EQUALIZER, CASSETTE TAPE PLAYER AND CD PLAYER Operating Instructions - Radio Mode NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek (Radio Mode) Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Time Press the TIME button to change the display between radio frequency and time. To set the clock, use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. Press any other button to exit from the clock setting mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction. Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the disc icon will be displayed in addition to the time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/CD-C Press the bottom of the AM/FM CD/CD-C button to switch between the CD and CD changer (if equipped). Time Press the TIME button to change the display from elapsed CD playing time to time of day. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBP, RBU, RAZ, and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. NOTE: Pressing the 9SEEK9 or 9SCAN9 button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL Heater Only — If Equipped Temperature Control The temperature control is the center knob located on the climate controls. It controls the temperature of the air delivered to the passenger compartment. The “Blue” area on the left side of the control indicates cooler temperatures while the “Red” area indicates warmer temperatures. Mode Selection The mode selector is the right knob located on the climate controls.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Bi-Level Air comes from both instrument panel and floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Defrost Air comes from the windshield outlets with a slight amount of air being directed through the floor and demisters. Use this setting when necessary to defrost or defog your windshield. Floor Air Conditioning — If Equipped Air comes from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The temperature control is the center knob located on the climate controls. It controls the temperature of the air delivered to the passenger compartment. Mode Selection The mode selector is the right knob located on the climate controls. It can be set in any of the following positions: The “Blue” area on the left side of the control indicates cooler temperatures while the “Red” area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Select this position when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior air only. Air flows through the panel outlets in this mode. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Panel Outside air flows through the air conditioning system, and then through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For improved safety, the A/C compressor is activated when “Mix” or “Defrost” modes are selected. This is done to assist in drying the air and it will help in keeping the windshield from fogging. Operating Tips Summer Operation The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 CAUTION! Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements. Rear Window Wiper/Washer To utilize the rear wiper, press the switch to the first detent. To activate the rear washer, depress the switch to the second detent.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 160 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 160 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 160 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 160 m Four–Wheel Drive Operation (Command-Trac™ Or Rock-Trac™) — If Equipped . . . . . . . . . . . 170 ▫ Operating Instructions/Precautions . . . . . . . . . 170 ▫ Shift Positions . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING m Off-Road Driving Tips . . . . . . . . . . . . . . . . . . 181 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 193 ▫ When To Use Low Range . . . . . . . . . . . . . . . 181 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 194 ▫ In Snow, Mud And Sand . . . . . . . . . . . . . . . . 181 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 194 ▫ Hill Climbing . . . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Alignment And Balance . .
STARTING AND OPERATING 159 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 202 ▫ Shifting Into Neutral (N) . . . . . . . . . . . . . . . . 205 ▫ Warranty Requirements . . . . . . . . . . . . . . . . . 203 ▫ Shifting Out Of Neutral (N) . . . . . . . . . . . . . . 206 m Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 m Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual Transmission Apply the parking brake, place the gearshift control lever in N (Neutral) and depress the clutch pedal before starting vehicle.
STARTING AND OPERATING 161 CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. Extreme Cold Weather (below –20°F or –29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. After Starting The idle speed will automatically decrease as the engine warms up. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle.
STARTING AND OPERATING TRANSMISSION SHIFTING 5-Speed Manual Overdrive Transmission Follow the shift pattern on the gearshift knob. NOTE: The backup lights will come on when your vehicle is in reverse gear and the ignition is in the ON position. 163 WARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake.
STARTING AND OPERATING • Do not downshift into a low gear while traveling at too high a speed for that gear. Engine, clutch, or transmission damage may result. • Do not rest your foot on the clutch pedal. This causes heat buildup and damages the clutch. • When you slow down or go up a grade, downshift as speed requires or the engine may overheat. • Never hold the vehicle stopped on a hill by using the clutch pedal. The clutch may be damaged.
STARTING AND OPERATING Clutch Interlocking Ignition System Manual transmission vehicles are equipped with a clutch interlock safety feature. With this feature engaged, you must depress the clutch pedal to allow cranking of the engine. To temporarily bypass this safety feature while off-road driving, which will allow cranking the engine without depressing the clutch, follow these steps: 1. Locate the instrument panel fuseblock behind the glove compartment. 2.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING WARNING! Do not coast in N (Neutral) and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle. strong head winds, or trailer towing), turning off overdrive will improve performance and extend transmission life by reducing excessive shifting and heat buildup. Overdrive (O/D) For most city and highway driving.
STARTING AND OPERATING 2 (Second) For moderate grades and to assist braking on dry pavement or in mud and snow. Begins at a stop in low gear with automatic upshift to 2nd gear. Will not shift to 3rd. 1 (First) For hard pulling at low speeds in mud, sand, snow, or on steep grades. Begins and stays in low gear with no upshift. Provides engine compression braking at low speeds. WARNING! Never use P (Park) position with an automatic transmission as a substitute for the parking brake.
STARTING AND OPERATING Torque Converter Clutch A feature designed to improve fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly different feeling or response during normal operation in high gear. When the vehicle speed drops or during acceleration, the clutch automatically and smoothly disengages.
STARTING AND OPERATING NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshafts speeds must be equal for the shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. When operating your vehicle in 4L, the engine speed is approximately three times that of the 2H or 4H positions at a given road speed.
STARTING AND OPERATING 4H Position Four Wheel Drive High Range — Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces. N (Neutral) Position Neutral — Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in Section 5 of this manual.
STARTING AND OPERATING NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however, difficulty may occur due to the mating teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the vehicle rolling at 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h).
STARTING AND OPERATING WARNING! On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. AXLE LOCK (TRU–LOK™) — IF EQUIPPED The Axle Locker switch is located on the lower center of the instrument panel. This feature will only activate when the following conditions are met: • Key in ignition, vehicle in 4L (Low) range.
STARTING AND OPERATING 175 PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the BRAKE warning light in the instrument cluster will light. NOTE: The BRAKE warning light indicates only that the parking brake is applied. It does not indicate the degree of brake application. 5 NOTE: If the parking brake is applied and the vehicle is in motion, the BRAKE warning light will flash and a chime will sound.
STARTING AND OPERATING WARNING! WARNING! • Always fully apply the parking brake when leaving your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave a automatic transmission in P (Park), or a manual transmission in 1st gear. Make certain the transfer case is in gear. Failure to do so may cause the vehicle to roll and cause damage or injury.
STARTING AND OPERATING 177 If the parking brake is not completely released, the BRAKE warning light will remain on. WARNING! NOTE: Your vehicle has automatically adjusting rear brakes and we do not recommend any adjustment other than the maintenance performed by your authorized dealer. Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING WARNING! WARNING! To use your brakes and decelerate more safely, follow these tips: The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in personal injury, follow these guidelines: • • • • • • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage.
STARTING AND OPERATING 179 WARNING! WARNING! To help avoid personal injury, follow these tips: • Never reach through the steering wheel to operate steering column controls. Injury to your hands or loss of vehicle control may result. • If the engine stalls or power assist fails due to a malfunction, vehicle steering and braking will require greater effort. Significant over or under-inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness.
STARTING AND OPERATING WARNING! WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. 181 conventional 2-wheel drive vehicles any more than lowslung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers.
STARTING AND OPERATING Don’t shift to a lower gear than necessary to maintain headway. Over-revving the engine can spin the wheels and traction will be lost. help regulate your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. Do not downshift on icy or slippery roads because engine braking may cause skidding and loss of control.
STARTING AND OPERATING Traction Downhill Shift the transmission into a low gear and transfer case to 4L (Low) range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving. After driving off-road, it is always a good idea to check for damage.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H NOTE: LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 185 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 187 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The tire placard is located on the lower driver’s side instrument panel. Tire and Loading Information Placard 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 191 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Over inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING High Speed Operation 193 Radial-Ply Tires WARNING! WARNING! High speed driving with your vehicle under load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to maximum capacity at continuous speeds above 75 mph (120 km/h). Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident.
STARTING AND OPERATING WARNING! These indicators are narrow strips 1/16 inch (1.6 mm) thick and are found in the tread pattern grooves. Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING 195 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration, which may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Install chains on rear tires only. Tire chains may be installed on all models except Sahara. Follow these recommendations to guard against damage and excessive tire and chain wear: • Use chains on P205/75R15 or P215/75R15 tires only. P225/75R15, LT30 x 9.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. The suggested rotation method is the “forward-cross” shown in the following diagram.
STARTING AND OPERATING Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasoline that meets the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as Reformulated Gasoline.
STARTING AND OPERATING It is even more important to look for gasoline without MMT in Canada because MMT can be used at levels higher than allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Sulfur In Gasoline If you live in the northeast United States, your vehicle may have been designed to meet California low emission standards with clean burning, low sulfur, California gasoline.
STARTING AND OPERATING FUEL FILLER CAP (GAS CAP) The fuel cap is located on the left side of the vehicle. If the fuel cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING 201 CAUTION! WARNING! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • Remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle.
STARTING AND OPERATING WARNING! CAUTION! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle. Remember that everything put in or on the trailer adds to the load on your vehicle. Warranty Requirements The manufacturer’s warranty will apply to vehicles used to tow trailers for noncommercial use, however the following conditions must be met: • The “D” Overdrive range can be selected when towing.
STARTING AND OPERATING
STARTING AND OPERATING NOTE: Refer to “Recommended Fluids, Lubricants, and Genuine Parts” in Section 7 for axle differential lubrication specifications for towing. Shifting Into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing. SNOW PLOW Snow plows should not be added to the front end of your vehicle. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 6. Release brake pedal and ensure that there is no vehicle movement. 7. Shut the engine off and place the ignition key into the unlocked OFF position. Shifting Out Of Neutral (N) Use the following procedure to prepare your vehicle for normal usage. 8. Shift automatic transmission into P (Park). 1. Shift automatic transmission into N (Neutral) or depress clutch pedal on manual transmission. 9. Apply parking brake. 2. Shift transfer case lever into desired position. 10.
STARTING AND OPERATING 207 WARNING! CAUTION! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake. The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 210 ▫ Spare Tire Location . . . . . . . . . . . . . . . . . . . . 213 m If Your Engine Overheats . . . . . . . . . . . . . . . . 210 ▫ Tire Changing Procedures . . . . . . . . . . . . . . . 213 m Changing A Flat Tire . . . . . . . . . . . . . . . . . . . 211 m Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Tool Kit Location . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off. Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES Control to maximum heat, the Mode Control to floor, and the Fan Control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
WHAT TO DO IN EMERGENCIES To remove the jack from its stowage position, carefully release the rubber strap from the bracket. Turn the thumb screw counterclockwise to loosen jack and then remove it from the bracket. WARNING! Always store the jack, lug wrench, jack handle driver, jack extension, and spare, flat or damaged tire securely in the proper place. Never leave them loose in the vehicle where they could become dangerous projectiles during a quick stop or collision.
WHAT TO DO IN EMERGENCIES 213 Tire Changing Procedures Spare Tire Location To remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. If equipped with an anti-theft lug nut (A), use the “Key” (B) and the lug wrench. The “Key” is stored in the glove box. WARNING! You can be injured or killed if you try to change a wheel too close to moving traffic.
WHAT TO DO IN EMERGENCIES • Get everyone out of the vehicle before you jack it up. If the jack should fall, someone in the vehicle could be hurt. • Block tire diagonally opposite tire to be changed to prevent forward and backward vehicle movement. Instructions 1. Remove spare tire, jack and tools from stored location. 2. Before raising vehicle, loosen lug nuts on wheel with flat tire. 3. Assemble the jack and jacking tools as shown.
WHAT TO DO IN EMERGENCIES 215 5. Use a clockwise rotation to raise the jack. Raise vehicle just enough to be able to remove flat tire and install spare tire. 6. Remove lug nuts and wheel. 7. Position spare wheel/tire on vehicle and install lug nuts with cone-shaped end toward wheel. Lightly tighten nuts clockwise. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. 8.
WHAT TO DO IN EMERGENCIES • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Apply the parking brake firmly before jacking. • Always block the wheel diagonally opposite the wheel being raised. • Do not raise the vehicle higher than is necessary to remove the tire. • Never start the engine with the vehicle on a jack. • Do not let passengers sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack.
WHAT TO DO IN EMERGENCIES 217 Set the parking brake, place an automatic transmission in P (Park) (or N (Neutral) for a manual transmission). Turn off lights, heater, and other electrical loads. Observe charge indicator in the battery. If indicator is light or yellow, replace the battery. CAUTION! Use the “Jump Starting” procedure only when the charge indicator is dark in the center. Do not attempt jump starting when the battery charge indicator is bright or yellow.
WHAT TO DO IN EMERGENCIES WARNING! • Do not connect the cable to the negative terminal of the discharged battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting to jump start. 3.
WHAT TO DO IN EMERGENCIES 219 TOWING A DISABLED VEHICLE The manufacturer recommends towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the other end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ▫ Engine Timing Belt — 2.4L Engine . . . . . . . . . 233 m 4.0L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 224 ▫ Ignition Wiring System — 2.4L Engine . . . . . . 233 m Onboard Diagnostic System — OBD II . . . . . . 225 ▫ Crankcase Emission Control System . . . . . . . . 234 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . 226 ▫ Fuel Filter . . . .
MAINTAINING YOUR VEHICLE ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 238 m Fuse Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 238 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . 254 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Underhood Fuses (Power Distribution Center) . . . . . . . . . . . . . . 256 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . .
MAINTAINING YOUR VEHICLE 223 2.
MAINTAINING YOUR VEHICLE 4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE 227 If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. 229 • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Taxi, Police, or delivery service (commercial service) • Trailer towing • Off-road or desert driving Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. Engine Oil Viscosity Chart The proper SAE viscosity grade of engine oil should be selected based on the following recommendation and be within the operating temperature shown in the engine oil viscosity chart.
MAINTAINING YOUR VEHICLE 231 Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. 4.
MAINTAINING YOUR VEHICLE Inspect the drive belt for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, adjust the belts according to the specifications and procedures shown in the Service Manual. Special tools are required to properly measure tension and to restore belt tension to factory specifications.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. 233 • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing.
MAINTAINING YOUR VEHICLE Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! Check ventilation hose for indication of damage or plugging deposits. Replace if necessary.
MAINTAINING YOUR VEHICLE 235 CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is used while battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to battery. Do not use a “fast charger” to provide starting voltage.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 237 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated.
MAINTAINING YOUR VEHICLE Windshield Washers WARNING! Commercial windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Windshield Washer Aiming To change the aim of the windshield washers, place a safety pin into the nozzle opening and move the nozzle slightly. Continue making slight adjustments until you obtain the desired pattern.
MAINTAINING YOUR VEHICLE If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
MAINTAINING YOUR VEHICLE Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals or children. If ingested by a child, contact a physician immediately.
MAINTAINING YOUR VEHICLE 241 Adding Coolant When adding coolant, a minimum solution of recommended 50% ethylene glycol antifreeze coolant in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below -37°F (-38°C) are anticipated. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution.
MAINTAINING YOUR VEHICLE service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the BRAKE warning light shows system failure Be sure to clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result. Automatic Transmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance.
MAINTAINING YOUR VEHICLE 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Apply the brakes and shift the transmission into P (Park). 5. The fluid MUST be checked with the transmission in P (Park) to be sure that the fluid level is accurate. 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading.
MAINTAINING YOUR VEHICLE 247 Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16” (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle.
MAINTAINING YOUR VEHICLE CAUTION! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Front/Rear Axle Fluid Fluid Level Check Lubricant should be at bottom edge of the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea-coast localities. 249 Washing • Wash your vehicle regularly.
MAINTAINING YOUR VEHICLE Appearance Care For Fabric Top Models CAUTION! To maintain the appearance of your vehicle’s interior trim and top, follow these precautions: • Avoid leaving your vehicle unattended with the top down, as exposure to sun or rain may damage interior trim. • Do not use harsh cleaners or bleaching agents on top material, as damage may result. • Do not allow any vinyl cleaner to run down and dry on the paint, leaving a streak.
MAINTAINING YOUR VEHICLE 3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de-icing chemicals. Use warm water only if you must clean the window quickly. 5. Debris (sand, mud/dirt, dust, or salt) from off-road driving will have a major impact on zipper operation. Even normal on-road driving and vehicle washing will eventually impact window zipper operation.
MAINTAINING YOUR VEHICLE • Use Mopart Touch Up Paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. • Aluminum wheels should be cleaned regularly with mild soap and water to prevent corrosion. To remove heavy soil, select a non-abrasive, non-acidic cleaner. Do not use scouring pads or metal polishes. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.
MAINTAINING YOUR VEHICLE WARNING! Only remove the carpet for cleaning purposes. It provides insulation against high floor pan temperatures. You or your passengers could be burned if the carpet is not properly in place. Always put the carpet back into the vehicle before driving. 253 Follow These Steps To Replace The Carpet: 1. Place the front floor carpets in the vehicle. 2. Attach the carpet to the studs in the footwell and press on the attachment caps to secure the carpet. 3.
MAINTAINING YOUR VEHICLE Maintenance After Off-Road Driving After extended operation in mud, sand or water, or similar dirty conditions, have your brake drums, brake linings, and axle joints inspected and cleaned as soon as possible. This will prevent any abrasive material from causing excessive wear or unpredictable braking action. Following off-road usage, completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension and exhaust system for damage.
MAINTAINING YOUR VEHICLE To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orientation, engage the hinge hook formations on the lower edge of the glove box door with the hinge pins on the lower edge of the instrument panel.
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Your vehicle is equipped with an electrical power distribution center located in the engine compartment near the battery. This power center houses plug-in “Cartridge” fuses, ISO relays, and Mini (Micro) fuses. VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS — IF EQUIPPED Interior Lights Bulb Type Auto. Trans. Indicator Light . . . . . . . . . . . . . . . . . 658 Courtesy Lights, Under Dash (1) . . . . . . . . . . . . . . 906 Heater Control Lights (2) . . . . . . . . . . . . . . . . . . . 194 Rocker Switch Indicator Light (Rear Window Defogger, and Rear Wash/Wipe). . . . . . . . . . . . . . . ** Soundbar Dome Light . . . . . . . . . . . . . . . . . . . . . 912 ** Bulbs only available from authorized dealer.
MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 2.4 Liter Engine (SAE 5W-30, API Certified Engine Oil) 4.0 Liter Engine (SAE 10W-30, API Certified Engine Oil) Cooling System * 2.4 Liter Engine (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.0 Liter Engine (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 19 Gallons Metric 72 Liters 5 Qts 6 Qts 4.7 Liters 5.7 Liters 9 Qts 8.
MAINTAINING YOUR VEHICLE 259 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (4.0L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) API Certified SAE 5W-30 Engine Oil is recommended for the 2.4L engine. API Certified SAE 10W-30 Engine Oil is recommended for the 4.0L engine.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Manual Transmission Transfer Case Axle Differential (front-rear) Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopart ATF+4 Automatic Transmission Fluid. Mopart Manual Transmission Lubricant or equivalent. Mopart ATF+4 Automatic Transmission Fluid. Mopart Hypoid Gear Lubricant (SAE 80W-90) (API GL5) or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . 262 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 265 m Maintenance Schedules . . . . . . . . . . . . . . . . . . 262 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 262 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Schedule “B.” Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. 263 M A • Check the windshield washer solvent, add as required. I N T E • Check the tire pressure and look for unusual wear or N A damage.
M 264 MAINTENANCE SCHEDULES A I • Rotate the tires at each oil change interval shown on N Schedule “A” 6,000 miles (10 000 km) or every other T E interval shown on Schedule “B” 6,000 miles (10 000 N km). A N C E S C H E D U L E S 8 • After completion of off-road operation, the underside of the vehicle should be thoroughly inspected. Examine threaded fasteners for looseness.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions 265 M • Trailer towing • Taxi, police, or delivery service (commercial service) • Off-road or desert driving E N A N C E • If equipped for and operated with E-85 (ethanol) S C fuel. • Short trips of less than 10 miles (16.
M 266 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Inspect the engine air filter element, replace if N C necessary. E Inspect the PCV Valve, and replace if necessary.L S C H E D U L E S 8 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the transfer case fluid, add if necessary.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed.
M 268 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Inspect the engine air filter element, replace if N C necessary. E Inspect the PCV Valve, and replace if necessary.L S C H E D U L E S 8 Inspect the ignition cables, and replace if necessary (2.4L Only). Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced.
M 270 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Inspect the engine air filter element, replace if N C necessary. E Inspect the PCV Valve, and replace if necessary.L S C H E D U L E S 8 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Replace the timing belt (2.4L Only). Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced. Flush and replace the engine coolant.
M 272 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Inspect the engine air filter element, replace if N C necessary. E Inspect the PCV Valve, and replace if necessary.L S C H E D U L E S 8 108,000 (173 000) X Replace the spark plugs. Inspect the ignition cables, and replace if necessary (2.4L Only). Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” ‡Off-highway operation, trailer towing, taxi, limousine, bus, snow plowing, or other types of commercial service or prolonged operation with heavy loading, especially in 273 M hot weather, require front and rear axle service indicated with a ‡ in Schedule “B”. Perform these services if the vehicle is usually operated under these conditions.
M 274 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change the engine oil and engine oil filter. E Inspect the engine air filter element, and replace S C H E D U L E S 8 if necessary. Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the transfer case fluid.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Lubricate the steering and suspension ball joints. Lubricate the steering linkage joints and outer tie rod ends. Inspect the brake linings.
M 276 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Inspect the engine air filter element, and replace if necE essary. S C H E D U L E S 8 Inspect the PCV Valve, and replace if necessary.L Replace the ignition cables (2.4L Only). Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the drive belt, and replace as needed.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air filter element, and replace if necessary. Inspect the PCV Valve, and replace if necessary.L Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the drive belt, and replace as needed. Not required if previously replaced.
M 278 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Inspect the engine air filter element, and replace if necessary. E Replace the ignition cables (2.4L Only). S C H E D U L E S 8 Inspect the PCV Valve, and replace if necessary.L Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Replace the timing belt (2.4L Only).
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Prepare For The Appointment . . . . . . . . . . . . 280 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 280 m If You Need Assistance . . . . . . . . . . . . . . . . . . 280 m Warranty Information . . . . . . . . . . . . . . . . . . . 283 m Mopart Parts . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 283 WARRANTY INFORMATION See your manufacturer’s Warranty Information Booklet for information on warranty coverage and transfer of warranty.
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 177 Add-A-Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . 155 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 234 Air Conditioner Maintenance . . . . . . . . . . . . . . 235 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . 151 Air Conditioning Controls . . . . . . . . . . . . . . . . 152 Air Conditioning, Operating Tips . . . . . . .
INDEX Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . 244 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Warning Light . . . . . . . . . . . . . . . . . . . . . . . 119 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Brake/Transmission Interlock . . . . . . . . . . . . . . 166 Break-In Recommendations, New Vehicle . . . . . . 39 Bulb Replacement . . . . . . . . . . . . . . . . . .
INDEX Coolant Level . . . . . . . . . . . . . . . . . . . . . . . . 241 Disposal of Used Coolant . . . . . . . . . . . . . . . 240 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . 239 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Points to Remember . . . . . . . . . . . . . . . . . . . 242 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . 241 Selection of Coolant . . . . . . . . . . . . . . . . 240,258 Temperature Gauge . . . . . . . . . . . . . . . . . . .
INDEX Coolant Temperature Gauge . . . . . . . . . . . . . 118 Engine Oil Pressure Gauge . . . . . . . . . . . . . . 117 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 216 Emission Control System Maintenance . . . . 226,262 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 162 Break-In Recommendations . . . . . . . . . . . . . . .
INDEX Power Steering . . . . . . . . . . . . . . . . . . . . . . . 236 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . 52 Folding Windshield . . . . . . . . . . . . . . . . . . . . . 102 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . . 170 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Four Wheel Drive Operation . . . . . . . . . . . . . . 170 Front Axle . . . . . . . . . . . . . .
INDEX Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242,243 Hydraulic Clutch Fluid . . . . . . . . . . . . . . . . . . 246 Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . 29,30 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . .
INDEX Daytime Running . . . . . . . . . . . . . . . . . . . . . . 58 Dimmer Switch, Headlight . . . . . . . . . . . . . . . 57 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 57 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . 117 High Beam Indicator . . . . . . . . . . . . . . . . . . . 117 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 57 Interior . . . . . . . . . . . . . . . . . . . . . .
INDEX Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . 227,284 Multi-Function Control Lever . . . . . . . . . . . . . . . 56 New Vehicle Break-In Period . . . . . . . . . . . . . . . 39 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . 16 Octane Rating, Gasoline . . . . . . . . . . . . . . . . . . 197 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Off-Pavement Driving . . . . . . . . . .
INDEX Rear Window Defroster . . . . . . . . . . . . . . . . . . 154 Rear Window Features . . . . . . . . . . . . . . . . . . . 154 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . 155 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 46 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 50 Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Recreational Towing . . . . . . . . . . . . . . . . . . . . .
INDEX Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Sentry Key Programming . . . . . . . . . . . . . . . . . . 13 Sentry Key Replacement . . . . . . . . . . . . . . . . . . 13 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 280 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . 282 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 285 Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . 120 Shift Indicator Light . . . . . . . . .
INDEX Tire and Loading Information Placard . . . . . . . 188 Tire Identification Number (TIN) . . . . . . . . . . . 187 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . 184 Tire Safety Information . . . . . . . . . . . . . . . . . . . 184 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 192 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Alignment and Balance . . . . . . . . . . . .
INDEX Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 58,116 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . . . 256 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 252 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . 242 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 48 Vehicle Identification Number . . . . . . . . . . . . . . . 7 Vehicle Modifications/Alterations . . . . . . . . . . . . 8 Vehicle Storage . . . . . . . . . . . . . . . . . . .
