SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 7 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeep威 Wrangler and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle. Before you start to drive this vehicle, read the Owner’s Manual.
INTRODUCTION 5 Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle and serious injury or death. Because of its open-body construction, your vehicle offers less protection than closed vehicles in the event of an accident. Roll Over Warning Label Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury.
INTRODUCTION Operating this vehicle at excessive speeds or while intoxicated may result in loss of control, collision with other vehicles or objects, going off the road, or overturning, any of which may lead to serious injury or death. Also, failure to use standard seat belts subjects the driver and passengers to a greater risk of being thrown out of an open-body vehicle than out of a closed vehicle in an accident which can result in injury or death.
INTRODUCTION 7 WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of vehicle through windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .13 䡵 Steering Wheel Lock — If Equipped . . . . . . . . . .17 ▫ Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Manually Lock The Steering Wheel . . . . . . .18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 ▫ To Release The Steering Wheel Lock . . . . . . . . .18 䡵 Sentry Key Immobilizer System — If Equipped . .14 䡵 Doors And Locks . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .26 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .44 ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags . . . . . . . . . .27 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. 2 Ignition Key Insert the key fully, then turn the switch to one of the four illustrated positions. The key can be inserted or withdrawn only in the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to LOCK, and remove the key. Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. CAUTION! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 keys that have been programmed to the vehicle can be used to start and operate the vehicle for longer than the 2 second validation time period. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the SKIS indicator light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Important Note About Service A four digit PIN number is needed to service the Sentry Key Immobilizer System. This number can be obtained from your authorized dealer. However, this number can also be found on your customer invoice that you were given upon receipt of your vehicle. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 will sound and the SKIS indicator light will begin to flash. Turn the ignition switch OFF and remove the second key. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Manually Lock the Steering Wheel With the engine running, rotate the steering wheel 1/2 revolution from straight ahead position, turn off the engine and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To Release the Steering Wheel Lock Insert the key in the ignition and turn the wheel slightly to the right or left to disengage the lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! • For personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will be carrying children too small for adult-size belts, your seat belts can also be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt cannot do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you cannot straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. NEVER ride in the front seat of a vehicle with a passenger front airbag, unless the airbag is turned off. An airbag deployment can cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver Airbag • Passenger Airbag • Steering Wheel And Column • Instrument Panel • Crash Sensor • Interconnecting Wiring • Knee Impact Bolsters How The Airbag System Works • The Airbag Control Module (ACM) determines if a frontal collision is severe enough to require the airbags to inflate. • The ACM will not detect side, roll over, or rear impacts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! Ignoring the “Airbag Warning Light” in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and in the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time-babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • The rearward-facing infant carrier is for babies weighing up to about 20 lbs (9 kg), and one year old or more. The infant restraint must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. The infant carrier is held in the vehicle by the lap belt, lap/shoulder belt, or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat unless the passenger frontal airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 portion of the lap/shoulder belt, or on the free end of the lap belt to tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • In the rear seat, you may have trouble tightening the lap belt or lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 2 Rear Seat Latch Anchors In addition, there are tether strap anchorages behind the rear seat (on the floor behind each rear outboard seating position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forwardfacing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pull up on the shoulder portion of the lap/shoulder belt to tighten the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach a child restraint tether strap: For the rear outboard seating positions, route the tether over the rear seat and attach to the rear floor tether anchors. If the Add-A-Trunk™ option is present in the vehicle, the lid should be opened and positioned against the back of the rear seat prior to attaching and adjusting the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. • If the shoulder belt contacts the child’s face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have it serviced. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 ▫ Tilting Front Seats . . . . . . . . . . . . . . . . . . . . . .57 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .50 ▫ Fold And Tumble Rear Seat . . . . . . . . . . . . . . .57 ▫ Inside Automatic Dimming Compass/Temperature Mirror — If Equipped . . . . . . . . . . . . . . . . . . . .50 ▫ Removing The Rear Seat . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Parking Lights, Instrument Panel Lights, And Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .63 ▫ Headlight Dimmer Switch . . . . . . . . . . . . . . . .63 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . .63 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 49 ▫ Console Storage Compartment — If Equipped . .72 ▫ Putting Up The Soft Top . . . . . . . . . . . . . . . . 117 ▫ Add-A-Trunk™ — If Equipped . . . . . . . . . . . .72 ▫ Sunrider — If Equipped (Unlimited Models Only) . . . . . . . . . . . . . . . . 125 䡵 Dual Top — If Equipped . . . . . . . . . . . . . . . . . .73 ▫ Removing The Soft Top . . . . . . . . . . . . . . . . . .73 ▫ Installing The Soft Top . . . . . . . . . . . . . . . . . .75 䡵 Hard Top . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. The compass/temperature display provides the outside temperature and one of eight compass headings (N, NE, E, SE, S, SW, W, NW).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Calibration Automatic Calibration Once calibrated, the compass has the ability to selfcorrect for changes in magnetic field to keep the compass accurate. This is referred to as Automatic Calibration. If magnetic field changes are too great, the compass will enter CAL mode on it’s own and manual calibration will be required.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Compass Variation Adjustment Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map. NOTE: When the mirror is in the VAR mode, the letter “Z” will be displayed along with the currently selected zone number.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON, and press and hold the center button for 3 to 6 seconds. The last variance zone number will be displayed. Each press of the center button will select a new variance zone. When the proper zone is selected, wait 5 seconds to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 WARNING! • Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. • Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Front Seat Adjustment Move seat forward or rearward by lifting the lever. Be sure the latch engages fully.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline To adjust seatback, lift lever, lean back, and release lever at desired position. To return seatback, lift the lever, lean forward and release the lever. Front Seat Recline Lever WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 Tilting Front Seats Push the lever upward on the seatback to tilt the entire seat forward. Fold And Tumble Rear Seat To expand the cargo area: 1. Slide seat belts through the seat cushions into the cargo area. 2. Lift the seatback release lever and fold seatback forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Slowly flip the entire seat forward. Removing the Rear Seat WARNING! Folding Rear Seat 4. When completed, return seat to it’s normal position. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 • Press down on release bar on each side, and pull seat out and away from lower bracket. • Remove seat from the vehicle. Replacing the Rear Seat Reverse steps for removing the seat. Be certain to pull the seat belts between the seat cushion and seatback. Position them for passenger use. WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open hood, first release both hood latches. have to push down slightly on hood before lifting up on handle. Insert the support rod into the slot in the radiator support. Hood Latch Location Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and radiator support and lift up on handle to raise hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 To close the hood, remove the support rod from the radiator support and place it in the retaining clip. Lower the hood slowly, then let it drop the last few inches. Secure both of the hood latches. LIGHTS WARNING! Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the muti-function control lever fully upward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The multi-function control lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming, and turn signals. Parking Lights, Instrument Panel Lights, and Headlights Turn the end of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 NOTE: If the driver’s door is left open, and the headlights or parking lights are left on, the “High Beam Indicator Light” will flash and a chime will sound. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. Headlight Dimmer Switch Pull the multi-function control lever towards you to switch the headlights to HIGH beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective. NOTE: A tone will chime if the turn signals are left on for more than 1 mile (2 km). Daytime Running Lights — Canada Only The headlights come on at a low intensity level after the vehicle has been driven approximately 3 feet (1 meter). They will turn off when the vehicle is turned off or when the headlights are switched on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Windshield Wiper Operation Move the lever upward to the second detent for LO speed wiper operation, or to the third detent for HI speed operation Windshield Washers To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back upwards to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory. Pressing the ON·OFF button or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting When the Speed Control is on and set, speed can be increased by pressing and holding the RESUME/ACCEL button. When the button is released, a new set speed will be established. Tapping the RESUME/ACCEL button once will result in a 2 mph (3 km/h) speed increase. Each time the button is tapped, speed increases, so tapping the button three times will increase speed by 6 mph (9 km/h), etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 ELECTRICAL POWER OUTLET To the right of the cigar lighter (if equipped) is the 12 volt power outlet. The outlet is connected directly to the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting. The outlet includes a tethered cap labeled with a battery symbol indicating the power source.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off WARNING! CUP HOLDERS In the center console there are two cup holders for the front seat passengers. • Many accessories that can be plugged in draw power NOTE: The cup holder insert is removable from the console, for cleaning. from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 The rear passengers have cup holders at the rear of the center console. STORAGE Glove Compartment To open the glove compartment, pull the latch up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Storage Compartment — If Equipped To unlock, insert key and turn. To open, press the latch button. Add-A-Trunk™ — If Equipped The factory-installed Add-A-Trunk™ option provides a secured compartment for parcels or equipment when the tailgate is closed and locked. To gain access to this compartment, simply open the tailgate and release the spring loaded latch pins. The cover of the Add-ATrunk™ can then be raised.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 DUAL TOP — IF EQUIPPED If your vehicle is equipped with a Dual Top, you must remove one of the tops from the vehicle. The soft top was installed at the factory for shipping purposes only. The soft top and the hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top, should both tops remain on the vehicle at the same time. Removing The Soft Top 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Using a rubber mallet, carefully tap the knuckles from the outside edge. This will disconnect the bow assembly from the pivot bracket. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot bracket. Remove the brackets using a #T40 Torx威 head driver. Recover and re-zip the sports bar cover. Store pivot brackets and screws in a safe place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Installing the Soft Top NOTE: The following procedures are for first time set up only. For future soft top procedures, refer to “Soft Top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (4) • right and left quarter windows 6. Reinstall the hard top. Refer to “Hard Top Installation” in this section. • rear tailgate window. 2. Remove the hard top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. a. If the pivot brackets have been removed, unzip the sport bar cover and attach the pivot brackets and screws with a #T40 Torx威 head driver. Re-cover and re-zip sport bar cover. b. If the door frames have been removed, re-install them (refer to “Door Frame” in this section). c.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. NOTE: A visual instruction sheet is enclosed in the dual top wrap. 6. Open the tailgate. 7. Remove the tailgate bar (black bar with end caps) that is located in the soft top and set aside. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 8.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Working from the rear of the vehicle with the tailgate open, lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 12. Move to the side of the vehicle and pull the side bow forward and down. You will see the 3 bow rise from the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 13. Unclip and move the sun visor to the side. 14. Open the header latches and engage the hooks on each side into the windshield slot. NOTE: Do not latch at this time. 3 15. Grasp the drip rail retainers and untuck them from the door frame. The soft top fabric should cover the header completely from one side to the other.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE require you to pull some of the fabric down and around the corners. Repeat this step for the other side. are not twisted or wrapped around the 2 bow. Move to the rear of the vehicle and gently pull the rear corners (sail panels) over the 3 bow letting them hang down. NOTE: Do not tuck the drip rail retainers into the frame at this time. 16. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 attaching it with the Velcro威. Exit the vehicle, and go to the rear of the vehicle. Fold the rear seat and sit in the rear cargo area facing rearward. Look up at the 3 bow and locate the 4 snaps on the 3 bow. Grasp the fabric (fabric contains snaps), and pull it around the 3 bow, and attach all 4 snaps. Return rear seat to it’s original position. 18. Align the sail panel retainer to the edge of the body side retainer at the rear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panels. 19. To install the quarter windows, affix the rear corner of the quarter window temporarily to the Velcro威. Start and zip the zipper only about 1 inch (2.5 cm). At this time, it is necessary to tuck in the door frame retainer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 20. Tuck in the bottom retainers on the quarter windows into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 21. Locate the black retainer bar that was set aside, and the rear window. Remove and discard the end caps. Slide the retainer bar over the receiver at the bottom inside of the rear window with the bulky seal away from you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 22. Zip the rear window beginning from the left using both zipper ends. Run the upper zipper around the window to the right side leaving the lower zipper end at the start on the left. 23. Tuck in the retainer bar ends into the tailgate clips on each side of the tailgate opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 24. Tuck the lower retainers on both sides of the rear window under the tailgate clips. Reinstall the left sail panel if it was untucked to get the rear window zipper started. 25. Tuck the drip rail retainers into the door frame slots above the door on both sides.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 26. Close the header latches and return the sun visor to it’s secure position. HARD TOP CAUTION! • The hard top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Hard Top Removal 1. Fold down the sun visors and move them to the side. 2. Unlatch the two hard top latches located at the top of the windshield. 3 CAUTION! 3. Unbolt the six Torx威 head screws which secure the hard top to the vehicle using a #40 Torx威 head driver. When removing the 2 front screws just rearward of the doors, make sure that the nut does not fall into the seat belt retractor. Grasp the nut to prevent this from occurring.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: On a dual top vehicle, the two rear and center nuts are retained onto the bodyside. 4. Open both doors. 5. Open tailgate all the way to ensure clearance of the rear window glass. Lift rear window glass. 6. Locate the wiring harness at the rear left side corner of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 7. Disconnect the washer hose and install the tethered cap. CAUTION! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system. 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pulling to disconnect.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected from the hard top. NOTE: If the doors are to be removed, pull the #4 fuse from the fuse block to prevent dome lamp illumination.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 SOFT TOP CAUTION! • The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result. • Do not lower the top when the windows are dirty. Grit may scratch the window. • Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered. • Do not lower the top with the windows installed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half door window by opening the door and lifting the half door window out. NOTE: Stow half doors carefully outside of the vehicle, never inside to avoid scratches. 2. Grasp the fabric of the top above the door frame.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Unclip and move the sun visor to the side. 4. Release the header latches and leave the hooks in the windshield slots. 5. Open the tailgate, partially unzip the rear window on each side, and untuck the lower retainers on the window from the tailgate clips on both sides of the tailgate opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 6. Pull the retainer bar straight out from the tailgate clips. to the top. Pull up on the window to disengage zipper end. Stow the windows carefully to avoid scratching. 7. Beginning from the rear, moving forward, partially unzip the side window and untuck the bottom retainers. • Remove the rear window entirely.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. NOTE: Stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the bodyside retainer. NOTE: If difficulty is experienced with fabric tension, place your hand on the rear upper corner of the top and pull down to help untuck the sail panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 10. Completely release the hooks on the rear side of the windshield. Grasp the side bow behind the header and lift top back. 3 11. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. NOTE: If your vehicle is equipped with a Dual Top, prevent connector damage by ensuring that the hard top wire harness is folded back and secured to the main harness, using the attached Velcro威 strap. 12.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tuck the top material between the 2 bow and the 3 bow as it folds. 13. Tuck the top material between the 2 bow and the header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 14. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 3 Putting Up The Soft Top 15. After the top is folded down, tuck the check straps so that they are not hanging and flapping outside the vehicle. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 1. Begin working from the rear of the vehicle, with the tailgate open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 2. Move to the side of the vehicle and pull the side bow forward and down. Be sure the check straps are not tangled around the 2 bow. You will see the 3 bow rise from the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 3. Unclip and move the sun visor to the side. 4. Open the header latches and engage the hook on each side into the windshield slot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Grasp the drip rail retainer and untuck them from the door frame. NOTE: Do not tuck the drip rails into the door frame at this time. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 7. Align the sail panel retainer to the edge of the bodyside retainer at the rear. Tuck the sail panel into the bodyside retainer beginning from the rear and working to the corner. Tuck the retainer around the corner and continue forward. NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panel retainers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. To install the quarter window, affix the rear corner of the window temporarily to the Velcro威. Start and zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has been completely tucked in, finish zipping in the window. Then affix the Velcro威 flaps around the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 10. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. To assist in getting the zipper started, lay the retainer bar inside the vehicle on the wheel wells and uninstall half of the left sail panel from the bodyside retainer beginning at the tailgate to expose zipper ends.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper at the start. 13. Tuck the retainer bar into the tailgate clips.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 14. Tuck the lower retainers of the rear window under the tailgate clips. Reinstall the left corner if it was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slot above the door on both sides.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Close the header latches and return the sun visor to it’s secured position. SOFT TOP — UNLIMITED MODELS CAUTION! • The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains. CAUTION! • Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • Do not lower the top when the temperature is below 41°F (5°C).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 1. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start at the back of the rear drip rail retainer and work forward towards the windshield. Repeat this on the other side. 3. Release the header latches and hooks from the windshield slots. 3 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Grip and rotate the retainer bar up towards you to release it from the upper portion of the tailgate clips. The retainer bar runs along the bottom of the rear window. will remain on the zipper track attached to the top. Pull up on the window to disengage zipper end. Stow window carefully to avoid scratching. 7. Undo the Velcro威 that runs along the top and rear edge of the side window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. NOTE: Stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the rear corners of the vehicle. NOTE: If difficulty is experienced with fabric tension, place your hand on the rear corner of the top and pull down to help untuck the corners.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Release the Sunrider pins to release the top bows from the brackets located on both door rails. Push up and back on the bow slightly so it does not fall back and lock into the brackets. 11. Grasp the side bow behind the header and lift the top back.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 12. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. 13. Make sure the sides of the top are folded inward as the top continues to fold, and check straps are clear of the vehicle. Tuck the top between the 2 bow and 2-1/2 bow and 2-1/2 bow and 3 bow as it folds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Tuck the top material between the 2 bow and the header. 15. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 16. After the top is folded down, tuck the check straps inside the rear corners of the vehicle. This will keep them from hanging and flapping outside the vehicle. 3 Putting Up The Soft Top 17. Hook the header latches back onto the header to keep them from rattling. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. Make certain Sunrider sleeves are covering the Sunrider links. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Begin working from the rear of the vehicle with the tailgate open. Standing to the side of the vehicle, lift the top by the 2 bow and 3 bow over the sport bar. become so tight that it will make many of the remaining steps difficult or even impossible. That is why locking the latches will be the last step. 4. Engage the hooks on each side of the header into the windshield slots and do not fully engage the header latch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 5. Pull the side bow forward and down. Make certain the blocks on the side bows line up with the retainers on the door rails. Lock the blocks in place. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow. 3 NOTE: Check to make certain the check straps are not tangled on any of the other top hardware. This will prevent the top from being put all the way up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Tuck the sail panel retainer into the bodyside retainer. Begin working from the rear tailgate opening and work to the corner. NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and pull down to help tuck in the sail panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 8. To install the quarter windows, affix the upper rear corner of the window temporarily using the Velcro威. Next, start the zipper about 1 inch (2.5 cm) at the upper forward corner of the window. At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has been completely tucked in, finish zipping in the window. Then affix the Velcro威 flaps around the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Tuck the bottom retainer on the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper in at the start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: To assist in getting the zipper started, lay the bar inside the vehicle on the right wheel well, uninstall half of the left sail panel from the bodyside retainer, beginning near the tailgate open to expose zipper ends. 12. Tuck the retainer bar into the upper portion of the tailgate clips.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 13. Tuck the lower retainers on the rear window under the tailgate clips. 14. Reinstall the corner of the sail panel that was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slots above the door on both sides. Start at the front next to the windshield and work rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 16. Fully engage the header latch. SUNRIDER — IF EQUIPPED (UNLIMITED MODELS ONLY) NOTE: If you are going to be driving faster than 40 mph (64 km/h) with the Sunrider feature open, it is recommended that you remove the rear window of the vehicle. 17. Return the sun visors to their secure position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise 1. Grasp the drip rail retainers and untuck both of them starting at the rear of the door frame slot. Repeat this on the other side. 2. Unclip and move the sun visors to the side. 3. Release the header latches, and slide the plastic sleeves forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Secure latches to plastic retainer on header. 5. Locate strap to secure the header to the sport bar. Wrap strap around sport bar and hook to header and tighten. 3 6. Attach and reposition sun visors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Lower 1. Remove strap from header and sport bar. 2. Release header latches from header retainer. 3. Unclip and move the sun visors to the side. 4. Grasp the front header and pull to the front of the vehicle. 5. Slide plastic sleeve rearward over Sunrider link. 6. Tuck drip rail retainers into the door frame slots. 7. Close the header latches, and return sun visors to their original position. NOTE: Sunrider is a trademark of Bestop, Inc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 2. Fold the door frames and store the knobs and door frames outside of the vehicle. Repeat this step for the other side. WARNING! • Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. • Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Slide door frame forward until the pin holes in the top line up with the holes in the side bar. Screw in the knobs and tighten, beginning with the front knob. Repeat procedures on the other side. FOLDING WINDSHIELD The fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 If required for certain off-road uses, the side bars can be removed and the windshield folded down. However, the protection afforded by these features is then lost. If you remove the side bars and fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred, if you are driving off-road with the windshield folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Carefully follow these warnings to help protect against personal injury: • Do not drive your vehicle on-road with the windshield down. • Do not drive your vehicle unless the windshield is securely fastened, either up or down. • Eye protection, such as goggles, should be worn at all times when the windshield is down. • Be sure that you carefully follow the instructions for raising the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3. Remove the two Torx威 head screws holding each side bar to the windshield frame. Shift the side bar inboard to clear windshield pillar molding when removing the side bar. 4. Unzip the sport bar padding to expose the side bar bolts. Remove the two front and rear Torx威 head screws for each bar. Remove the side bars and rezip sport bar padding in place. 3 NOTE: Store all of the mounting bolts in their original threaded holes and tighten for safekeeping.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not remove the head impact foam from the side bars, as damage to the foam may result. 5. To safely store the side bars in your vehicle, use four of the cinch straps, found in the glove box. Attach the straps through the footman loops located in the floor behind the folded rear seat on each side of the vehicle. WARNING! You or others could be injured if you carry the side bars loose in your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 7. Remove the black round headed windshield Torx威 head screw on each side of the base of the windshield. 8. Lower the windshield gently until it contacts the rubber hood bumpers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Secure the windshield by passing the remaining cinch strap, found in the glove box, through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising The Windshield And Replacing Side Bars To raise the windshield, install the windshield wipers, and install the side bars use these same steps in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 REAR WINDOW FEATURES — HARD TOP ONLY Rear Window Defogger To turn the rear window defogger on, press the rocker switch. If you press the switch a second time, you will turn the defogger off. A light on the rocker switch will indicate the defogger is on. The defogger will automatically turn off after about ten minutes. For five more minutes of operation, depress the top of the switch to turn the defogger on again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Wiper/Washer To utilize the rear wiper, press the switch to the first detent. To activate the rear washer, depress the switch to the second detent. The washer will continue to spray as long as the switch is held. The switch will return to the wiper mode when released. To turn the rear wiper off, lift the bottom of the switch.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Interior Controls . . . . . . . 141 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 149 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 142 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 149 䡵 Instrument Cluster Description . . . . . . . . . . . . . 143 䡵 Sales Code RBK—AM/ FM Stereo Radio With CD Player And CD Changer Controls . . . . . . . . 150 䡵 Electronic Digital Clock . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 156 ▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 166 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 159 ▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 166 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 163 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 167 ▫ System Activation . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENT PANEL AND INTERIOR CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER DESCRIPTION Your vehicle is equipped with the instrument cluster described on the following pages. 1. Voltmeter Indicates available battery voltage and charging system operation. The lower red zone indicates that battery charge may be too low to start the engine. With the engine running, the normal operating range is between 11 and 15 volts.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. High Beam Indicator Light This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low. If the driver’s door is open, and the headlights or parklights are left on, the “High Beam Indicator Light” will flash and a chime will sound. 8. Seat Belt Indicator Light A warning chime and an indicator light will alert you to buckle the seat belts.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 13. Oil Pressure Gauge Indicates engine oil pressure. This gauge does not indicate oil level, and pressure varies with engine speed, temperature and oil viscosity. Consistent lower readings indicate possible malfunction. Seek authorized service. 14. Coolant Temperature Gauge Indicates engine coolant temperature. The red zone to the far right indicates possible overheating. Seek authorized service immediately if the gauge operates in the red zone. In U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 20. Anti-Lock (ABS) Warning Light After ignition is turned on, illuminates to indicate function check at vehicle start-up. If light remains on after start-up or comes on and stays on at road speeds, it may indicate that the ABS has detected a malfunction or has become inoperative. The system reverts to standard non-anti-lock brakes. If the parking brake is applied and the vehicle is in motion, the red BRAKE warning light will “flash” and a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 23. Fuel Cap Indicator This symbol indicates the side of the vehicle where the fuel cap is located. 24. Fuel Gauge The pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to E, for your safety, approximately 2 U.S. Gallons (7.6L) of fuel remain. NOTE: When the ignition switch is turned to OFF, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. Satellite Radio (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. To select Sirius Satellite Radio™ (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING YOUR INSTRUMENT PANEL show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player. Radio display will show “loading” when it is being loaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Time Press the TIME button to change the display from elapsed CD playing time to time of day. CD ERROR will appear on the display if the laser is unable to read the Disc data for the following reasons: • Warped disc Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. • Excessive vibration CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-5397474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Switch The blower switch is the rotary knob to the left of the controls. The blower speed will increase as the knob is turned clockwise. There are four blower speeds. Mode Selection The mode selector is the right knob located on the climate controls. It can be set in any of the following positions: NOTE: The blower motor will run until the mode control knob is turned to the “Off” (“O”) position or the ignition is turned OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 Bi-Level Outside air comes from both instrument panel and floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Defrost Outside air comes from the windshield outlets with a slight amount of air being directed through the floor and demisters. Use this setting when necessary to defrost or defog your windshield. Floor Air Conditioning — If Equipped Outside air comes from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The temperature control is the center knob located on the climate controls. It controls the temperature of the air delivered to the passenger compartment. Mode Selection The mode selector is the right knob located on the climate controls. It can be set in any of the following positions: Mode Selection Knob Temperature Control Knob You can choose your degree of comfort by rotating the knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Recirculation Select this position when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior air only. Air flows through the panel outlets in this mode. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Panel Outside air flows through the air conditioning system, and then through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Outside air comes from the windshield outlets with a small amount being directed through the floor outlets. Use this setting when necessary to defrost your windshield. NOTE: For improved safety, the A/C compressor is activated when “Mix” or “Defrost” modes are selected. This is done to assist in drying the air and it will help in keeping the windshield from fogging.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 178 䡵 Transmission Shifting . . . . . . . . . . . . . . . . . . . . 181 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 178 ▫ 6-Speed Manual Transmission . . . . . . . . . . . . 181 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 178 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 184 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Axle Lock (Tru–Lok™) — If Equipped . . . . . . . . 195 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 207 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 196 ▫ Tire Identification Number (TIN) . . . . . . . . . . 210 䡵 About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 198 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 211 䡵 Anti-Lock Brake System — If Equipped . . . . . . . 200 䡵 Tires — General Information . . . . .
STARTING AND OPERATING 177 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 222 䡵 Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . 226 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 223 ▫ Locking Fuel Filler Cap (Gas Cap) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 223 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 224 ▫ Materials Added To Fuel . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual Transmission Apply the parking brake, place the gearshift control lever in N (Neutral) and depress the clutch pedal before starting vehicle.
STARTING AND OPERATING 179 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal starting procedure. Extreme Cold Weather (below –20°F or –29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended. If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded.
STARTING AND OPERATING If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. After Starting The idle speed will automatically decrease as the engine warms up.
STARTING AND OPERATING 181 WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. 5 TRANSMISSION SHIFTING 6-Speed Manual Transmission Follow the shift pattern on the gearshift knob. NOTE: The backup lights will come on when your vehicle is in reverse gear and the ignition is in the ON position.
STARTING AND OPERATING WARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. • Do not operate at sustained high engine or road speeds in lower gears. Engine damage may result. • Do not downshift into a low gear while traveling at too high a speed for that gear. Engine, clutch, or transmission damage may result.
STARTING AND OPERATING 183 • Push in the clutch pedal completely when shifting. Otherwise, transmission or clutch damage may result. • When “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • The manual transmission may be equipped with a “Reverse Blocker” to prevent inadvertent shifts from 5th gear to Reverse.
STARTING AND OPERATING off-road driving (4L range only), which will allow cranking the engine without depressing the clutch, follow these steps: 1. Locate the Power Distribution Center (PDC) in the engine compartment. Refer to “Fuse Panel” in Section 7 of this manual. Automatic Transmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped.
STARTING AND OPERATING 185 WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 187 CAUTION! WARNING! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shifter could result. Do not coast in N (Neutral) and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle.
STARTING AND OPERATING When frequent transmission shifting occurs while using Overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off overdrive will improve performance and extend transmission life by reducing excessive shifting and heat buildup. Overdrive can be locked out by pressing the O/D OFF switch located on the instrument panel.
STARTING AND OPERATING 189 WARNING! CAUTION! Never use P (Park) position with an automatic transmission as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Before moving the shift lever out of P (Park), you must turn the ignition from LOCK so the steering wheel and shift lever are released. Otherwise, damage to steering column or shifter could result.
STARTING AND OPERATING NOTE: The transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation in D (Drive) position. If the transmission becomes hot enough, the TRANS TEMP warning light in the instrument cluster will come on.
STARTING AND OPERATING 191 Operating Instructions/Precautions The transfer case provides four mode positions — two (rear) wheel drive high range, four wheel drive high range, neutral, and four wheel drive low range. This transfer case is intended to be driven in the two wheel drive (2H) position for normal street and highway conditions such as dry hard surfaced roads.
STARTING AND OPERATING Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Shift Positions Because four wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. 2H Position Rear Wheel Drive High Range — Normal street and highway driving.
STARTING AND OPERATING 193 4L Position Four Wheel Drive Low Range — Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedure 2H to 4H or 4H to 2H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h).
STARTING AND OPERATING WARNING! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have an injury accident. Do not drive the vehicle unless the transfer case is fully engaged. TRAC-LOK™ REAR AXLE The Trac-Lok™ rear axle provides a constant driving force to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel.
STARTING AND OPERATING 195 AXLE LOCK (TRU–LOK™) — IF EQUIPPED The Axle Lock switch is located on the lower center of the instrument panel. • The vehicle must be traveling at 10 mph (16 km/h) or less. To activate the system, press the switch once to lock the rear axle only (the REAR LOCK indicator light will illuminate), press the switch again to lock the front axle (the FRONT LOCK indicator light will illuminate). Once the rear axle is locked, pressing the switch again will lock or unlock the front axle.
STARTING AND OPERATING PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the BRAKE warning light in the instrument cluster will light. NOTE: The BRAKE warning light indicates only that the parking brake is applied. It does not indicate the degree of brake application. NOTE: If the parking brake is applied and the vehicle is in motion, the BRAKE warning light will flash and a chime will sound.
STARTING AND OPERATING 197 NOTE: Your vehicle has automatically adjusting rear brakes and we do not recommend any adjustment other than the maintenance performed by your authorized dealer. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the P (Park) position (automatic transmission) or first gear (manual transmission). Make certain the transfer case is in gear.
STARTING AND OPERATING The parking brake should always be applied when the driver is not in the vehicle. WARNING! • Leaving children unattended in a vehicle is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate controls or move the vehicle. ABOUT YOUR BRAKES Your vehicle is equipped with power assisted brakes as standard equipment.
STARTING AND OPERATING 199 WARNING! WARNING! To use your brakes and decelerate more safely, follow these tips: The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in personal injury, follow these guidelines: • Always place cargo evenly on the cargo floor, and locate heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle.
STARTING AND OPERATING WARNING! To help avoid personal injury, follow these tips: • Never reach through the steering wheel to operate steering column controls. Injury to your hands or loss of vehicle control may result. • If the engine stalls or power assist fails due to a malfunction, vehicle steering and braking will require greater effort. ANTI-LOCK BRAKE SYSTEM — IF EQUIPPED The Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING 201 regulated hydraulic pressure. The motor pump makes a low humming noise during operation, this is normal. During off-road use, loss of traction can temporarily defeat the system and cause the warning light to illuminate. Turn the ignition OFF and ON again to restore Anti-Lock Brake System function. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning.
STARTING AND OPERATING 203 where additional low speed pulling power is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L (Low) range. Driving Through Water Although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water: CAUTION! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward.
STARTING AND OPERATING Standing Water Avoid driving in standing water deeper than 20 inches, and reduce speed appropriately to minimize wave effects. Maximum speed in 20 inches of water is less than 5 mph (8 km/h). Maintenance After driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission oil, axle, transfer case) to assure the fluids have not been contaminated.
STARTING AND OPERATING 205 your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back carefully straight down a hill in R (Reverse) gear. Never back down a hill in N (Neutral) using only the brake.
STARTING AND OPERATING After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage.
STARTING AND OPERATING 207 TIRE SAFETY INFORMATION Tire Markings • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 209 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 211 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressures are listed on the lower front inside corner of the driver door opening.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 213 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING 215 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper cold tire inflation pressures are listed on the lower front inside corner of the driver door opening. 3.
STARTING AND OPERATING 217 more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. High Speed Operation WARNING! Inflation pressures specified on the label are always “Cold Inflation Pressure.” Cold inflation pressure is defined as the tire pressure after the vehicle has been idle for at least 3 hours, or driven less than a mile after a 3 hour period.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial tires in sets of four. Never combine them with other types of tires. Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone.
STARTING AND OPERATING 219 Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in quality and performance when replacement is needed (see section on tread wear indicators). Failure to use equivalent replacement tires may adversely affect the safety, handling, ride and fuel economy of your vehicle.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Check with your dealer before replacing tires with a different size. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING 221 Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your dealer for proper diagnosis of the problem. Improper alignment will not normally cause vehicle vibration, which may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Install chains on rear tires only. Tire chains may be installed on all models except the Sahara and Rubicon.
STARTING AND OPERATING aggressive tread designs such as those on On/Off Road type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
STARTING AND OPERATING 223 premium gasoline will provide no benefit over high quality regular gasoline, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations.
STARTING AND OPERATING CAUTION! DO NOT use gasoline containing METHANOL. Gasoline containing methanol may damage critical fuel system components. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles.
STARTING AND OPERATING 225 • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance.
STARTING AND OPERATING the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. FUEL FILLER CAP (GAS CAP) The fuel cap is located on the left side of the vehicle. If the fuel cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING 227 CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • Turn the engine off.
STARTING AND OPERATING WARNING! WARNING! • Remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING 229 • Be sure to remove the key. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. TRAILER TOWING In this section you will find information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.
STARTING AND OPERATING A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg). WARNING! CAUTION! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
STARTING AND OPERATING 231 5
STARTING AND OPERATING NOTE: Refer to “Recommended Fluids, Lubricants, and Genuine Parts” in Section 7 for axle differential lubrication specifications for towing. Shifting Into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing.
STARTING AND OPERATING 233 5. Shift automatic transmission into D (Drive) or manual transmission into gear. CAUTION! 6. Release brake pedal and ensure that there is no vehicle movement. Damage to the transmission may occur if the transmission is shifted into P (Park) with the transfer case in N (Neutral) and the engine running. With the transfer case in N (Neutral) ensure that the engine is off prior to shifting the transmission into P (Park) (refer to steps 7 – 8 above). 7.
STARTING AND OPERATING NOTE: When shifting out of transfer case N (Neutral) on automatic transmission equipped vehicles, turning the engine off may be required to avoid gear clash. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 236 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 239 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 237 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 240 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 238 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 242 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
WHAT TO DO IN EMERGENCIES 237 Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes.
WHAT TO DO IN EMERGENCIES 239 NOTE: If you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations For Jacking Park on a firm level surface, avoid ice or slippery areas, set the parking brake and place automatic transmission in P (Park), or manual transmission in R (Reverse). Turn OFF the ignition.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. 4. Operate jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. • Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1.
WHAT TO DO IN EMERGENCIES 241 and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position spare wheel/tire on vehicle and install lug nuts with cone-shaped end toward wheel. Lightly tighten nuts clockwise.
WHAT TO DO IN EMERGENCIES JUMP STARTING WARNING! To prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin, or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other. Keep open flames or sparks away from battery vent holes. Always wear eye protection when working with batteries. Do not use a booster battery or any other booster source that has a greater than 12–volt system, i.e.
WHAT TO DO IN EMERGENCIES 243 1. Attach one end of the jumper cable to the positive terminal of the discharged battery and the other end of the same cable to the positive terminal of the booster battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 2. Connect one end of the other jumper cable to the negative terminal of the booster battery.
WHAT TO DO IN EMERGENCIES 4. After the engine is started or if the engine fails to start, the cables must be disconnected in the following order: a. Disconnect the negative cable at the engine ground. b. Disconnect the negative cable at the negative terminal on the booster battery. c. Disconnect the cable from the positive terminals of both batteries. WARNING! Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out the battery vent.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Drive Belts — Check Condition And Tension . . 257 䡵 4.0L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 258 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 250 ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 258 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 262 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 276 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 263 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . 277 ▫ Driveline And Steering Component Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 264 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . . 278 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 247 ▫ Front Side Marker . . . . . . . . . . . . . . . . . . . . . 292 䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 292 䡵 Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 ▫ Rear Tail, Stop, Turn Signal, And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ Center High Mounted Stop Light (CHMSL) .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 249 4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 251 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
MAINTAINING YOUR VEHICLE 253 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding 1 U.S. Quart (0.95L) of oil when the reading is at the ADD mark will result in a SAFE reading on these engines.
MAINTAINING YOUR VEHICLE 255 • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Taxi, Police, or delivery service (commercial service) • Trailer towing • Off-road or desert driving • If equipped for and operating with E–85 (ethanol) fuel If ANY of these apply to you, then change your engine oil at every interval shown in schedule “B” of the “Maintenance Schedules” section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (2.4L Engines) SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. Engine Oil Viscosity (4.0L Engines) SAE 10W-30 engine oil is recommended. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. 4.
MAINTAINING YOUR VEHICLE 257 Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the mileage specified in the appropriate maintenance chart.
MAINTAINING YOUR VEHICLE 259 WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Engine Timing Belt — 2.4L Engine Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition Wiring System — 2.4L Engine Replace the ignition cables at the intervals described in the appropriate maintenance schedule. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits.
MAINTAINING YOUR VEHICLE 261 WARNING! WARNING! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery.
MAINTAINING YOUR VEHICLE To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE 263 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information Book for additional warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 265 amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder. Windshield Washers Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
MAINTAINING YOUR VEHICLE WARNING! Commercial windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE 267 system should be drained, flushed and refilled with fresh antifreeze/coolant. Check the front of the A/C condenser (if equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the A/C condenser (if equipped) or the back of the radiator core.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of antifreeze/coolant other than the specified HOAT antifreeze/coolant may result in decreased corrosion protection and engine damage. If a non-HOAT antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coolant as soon as possible. • Do not use plain water alone or alcohol base antifreeze/coolant products.
MAINTAINING YOUR VEHICLE 269 Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
MAINTAINING YOUR VEHICLE children, do not store ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate.
MAINTAINING YOUR VEHICLE 271 coolant needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent antifreeze/coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain antifreeze/coolant concentration at 50% HOAT antifreeze/coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components.
MAINTAINING YOUR VEHICLE are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the appropriate “Maintenance Schedule” in Section 8 for suggested service intervals. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
MAINTAINING YOUR VEHICLE 273 WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the BRAKE warning light shows system failure Be sure to clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. WARNING! • Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE 275 CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE (cross-hatched area) on the oil level indicator. The fluid level indicator should be in the COLD region at 70° F (21° C) fluid temperature. If the fluid level is low, add sufficient fluid to bring to the proper level. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid is added through the dipstick tube.
MAINTAINING YOUR VEHICLE 277 Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. Transfer Case Fluid Level Check The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position.
MAINTAINING YOUR VEHICLE CAUTION! Front/Rear Axle Fluid When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Fluid Level Check Lubricant should be at bottom edge of the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.
MAINTAINING YOUR VEHICLE 279 Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Appearance Care And Protection From Corrosion Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE Washing Appearance Care For Fabric Top Models • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap and rinse the panels completely with clear water. CAUTION! • If insects, tar, or other similar deposits have accumulated on your vehicle, wash it as soon as possible.
MAINTAINING YOUR VEHICLE 281 • Be especially careful when washing the windows by following the directions for “Care of Fabric Top Windows.” 1. Never use a dry cloth to remove dust. Instead, use a soft cotton cloth moistened with cold or warm, clean water, and wipe across the window, not up and down. WASHING — Always use mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use a mild foaming cleaner on the entire top, but support top from underneath. 2.
MAINTAINING YOUR VEHICLE Soft Top Zipper Cleaner and Lubricant to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both sides of the zipper, not just one side. Rinse both zipper halves with fresh water and allow to dry. Aggressively work the Mopar威 Soft Top Zipper Cleaner and Lubricant into the zipper teeth. If a stuck zipper slide is experienced, work the Mopar威 Soft Top Zipper Cleaner and Lubricant into the zipper slide.
MAINTAINING YOUR VEHICLE 283 Do not use scouring pads or metal polishes. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Interior Care Use Mopar威 Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar威 Vinyl Cleaner to clean vinyl or leather upholstery. Mopar威 Vinyl Cleaner is specifically recommended for interior vinyl trim. WARNING! Do not use volatile solvents for cleaning purposes.
MAINTAINING YOUR VEHICLE WARNING! Only remove the carpet for cleaning purposes. It provides insulation against high floor pan temperatures. You or your passengers could be burned if the carpet is not properly in place. Always put the carpet back into the vehicle before driving. NOTE: If your vehicle is equipped with an Add-ATrunk™ it must be removed to be able to remove the cargo floor and wheelhouse carpets. For Add-A-Trunk™ removal procedure, refer to “Storage” in Section 3 of this manual.
MAINTAINING YOUR VEHICLE 285 Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
MAINTAINING YOUR VEHICLE FUSE PANEL Interior Fuses The fuse panel is located behind the glove box. Fuse Panel To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orientation, engage the hinge hook formations on the lower edge of the glove box door with the hinge pins on the lower edge of the instrument panel.
MAINTAINING YOUR VEHICLE 287 Cavity 1 7 Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red 8 9 10 11 10 Amp 10 Amp 10 Amp 10 Amp 2 3 4 5 6 Red Red Red Red Description Park Lights, Skim (Sentry Key) Stop Lights Cavity 12 Fuse 10 Amp Red 13 14 15 10 Amp Red 10 Amp Red 10 Amp Red Door Switch Defeat Airbag Rear Wiper 16 10 Amp Red 17 Back-Up Lights, Rear Window Defroster Relay, ABS HEVAC Airbag Instrument Cluster Solenoids, DRL 18 25 Amp Natural 20 A
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Your vehicle is equipped with an electrical power distribution center located in the engine compartment near the battery. This power center houses plug-in “Cartridge” fuses, ISO relays, and Mini (Micro) fuses. Power Distribution Center A label inside the latching cover of the center identifies each component for ease of replacement, if necessary. Cartridge and mini (micro) fuses can be obtained from your authorized dealer.
MAINTAINING YOUR VEHICLE 289 Cavity 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Fuse/Color 40 Amp Green Open 50 Amp Red Open 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Lt.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: REPLACEMENT BULBS — IF EQUIPPED • Store the removed IOD fuse in the Power Distribution Center location #11 labeled “IOD Storage.” Interior Lights Bulb Type Auto. Trans. Indicator Light . . . . . . . . . . . . . . . . . 658 Courtesy Lights, Under Dash (1) . . . . . . . . . . . . . . 906 Heater Control Lights (2) . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 291 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H3 Front Park/Turn Lights (2) . . . . . . . . . . . . . . . . . 3157 Front Side Marker Lights (2) . . . . . . . . . . 168 or W3W Headlights (2) . . . . . . . . . . . . . . . . . . . . . . H 6024BL Stop/Tail/Turn Lights (2) . . . . . . . . . . . . . . . . . . 1157 Underhood Light. . . . . . . . . . . . . . . . . . . . . . . . . 561 License Light. . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 4. Remove and replace the lamp. 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front Side Marker 1. Reach under the front fender and locate the front side marker socket. 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front Fog Light Front Park/Turn Signal 1.
MAINTAINING YOUR VEHICLE 293 3. Squeeze the bulb/element spring retainer from the reflector. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7 4. Disconnect the electrical connector.
MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, and Back-Up Lights 1. Remove the screws attaching the lens to the tailight housing. 2. Separate the lens from the housing. 3. Push the bulb in, turn it counter-clockwise 1/3 turn, then remove it from the housing, and replace. Center High Mounted Stop Light (CHMSL) The stop lamp is mounted on a bracket that extends upward from the tailgate. Remove the two screws holding the lens in place. Take the lens off and pull the bulb from the socket.
MAINTAINING YOUR VEHICLE 295 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 2.4 Liter Engine (SAE 5W-30, API Certified Engine Oil) 4.0 Liter Engine (SAE 10W-30, API Certified Engine Oil) Cooling System * 2.4 Liter Engine (Mopar威 Antifreeze/Engine Coolant 5 Year/ 100,000 Mile Formula) 4.0 Liter Engine (Mopar威 Antifreeze/Engine Coolant 5 Year/ 100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 19 Gallons Metric 71.9 Liters 5 Qts 6 Qts 4.7 Liters 5.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (4.0L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) API Certified SAE 5W-30 Engine Oil is recommended for the 2.4L engine. API Certified SAE 10W-30 Engine Oil is recommended for the 4.0L engine.
MAINTAINING YOUR VEHICLE 297 Chassis Component Automatic Transmission Manual Transmission Transfer Case Axle Differential (Front) Axle Differential (Rear) Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 Manual Transmission Lubricant or equivalent (meeting the requirements of DaimlerChrysler Material Standard MS-9224) Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent.
MAINTAINING YOUR VEHICLE Component Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 Multi-Purpose Grease NLGI Grade 2 EP, GC-LB or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 300 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 303 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 300 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 300 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 301 M • Off-road or desert driving • If equipped for and operated with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “Schedule B” of the “Maintenance Schedules” section of this manual.
M A I N T E N A N C E 302 MAINTENANCE SCHEDULES Once a Month • Inspect brake hoses. • Check the tire pressure and look for unusual wear or damage. • Check the coolant level, hoses, and clamps. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake S master cylinder, and transmission, and add as needed. C H E D U L E S 8 • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
M 304 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the transfer case fluid, add if necessary.
M 306 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.〫 Inspect the ignition cables, and replace if necessary (2.4L Only). Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
M 308 SCHEDULE “B” A I N Miles T (Kilometers) E N Inspect the drive belt and replace as needed. Not A required if belt was previously. N C Drain and refill the transfer case fluid. E Flush and replace the engine coolant/anti-freeze at S C H E D U L E S 8 60 months, if not done at 102,000 miles (163 000 km).
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced.
M 310 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Replace the timing belt (2.4L Only)〫. Inspect the brake linings.
SCHEDULE “B” 311 M Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced.
M 312 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Inspect the ignition cables, and replace if necessary (2.4L Only). Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Inspect the drive belt and replace as needed. Not required if belt was previously replaced. Drain and refill the transfer case fluid. Flush and replace the engine coolant/anti-freeze at 120 months, if not replaced at 102,000 miles (163 000 km). 108,000 (173 000) Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. † Applies only if vehicle is used for frequent trailer towing or fleet/commercial service.
M 314 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change the engine oil and engine oil filter. E Rotate the tires. S C H E D U L E S 8 Inspect the engine air filter element, and replace if necessary. Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the transfer case fluid.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Lubricate the steering and suspension ball joints. Lubricate the steering linkage joints and outer tie rod ends. Inspect the brake linings.
M 316 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Inspect the engine air filter element, and replace if necS C H E D U L E S 8 essary. Inspect the PCV Valve, and replace if necessary.〫 Replace the ignition cables (2.4L Only). Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Flush and replace the engine coolant/anti-freeze at 60 months, if not done at 102,000 miles (163 000 km). Inspect transfer case fluid.
M 318 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Inspect the engine air filter element, and replace if necS C H E D U L E S 8 essary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the drive belt, and replace as needed.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if necessary. Replace the ignition cables (2.4L Only). Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Replace the timing belt (2.4L Only).〫 Inspect the drive belt, and replace as needed.
M 320 SCHEDULE “A” A I 108,000 114,000 120,000 N Miles T (Kilometers) (173 000) (182 000) (192 000) E [108] [114] [120] N [Months] A Flush and replace the engine coolant/anti-freeze, if not done at X N 102,000 miles (163 000 km). C E Inspection and service should also be performed anytime 〫 This maintenance is recommended by the manufacS C H E D U L E S 8 a malfunction is observed or suspected. Retain all receipts. turer to the owner, but is not required to maintain emissions warranty.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ Prepare For The Appointment . . . . . . . . . . . . 322 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 322 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 322 䡵 Warranty Information . . . . . . . . . . . . . . . . . . . . 325 䡵 Mopar威 Parts . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 323 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE 325 We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE 327 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 329 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 198 ABS (Anti-Lock Brake) System . . . . . . . . . . . . 147,200 Add-A-Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 138 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 260 Air Conditioner Maintenance . . . . . . . . . . . . . . . 262 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 171 Air Conditioning Controls . . . . . . . . . . .
INDEX 333 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Body Mechanism Lubrication . . . . . . . . . . . . . . . 264 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 211 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Hoses . . . .
INDEX Child Restraint . . . . . . . . . . . . . . . . . . . . . . 34,38,41 Child Restraint Tether Anchors . . . . . . . . . . . . . 37,38 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 169 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Clutch Interlocking Ignition System . . . . . . . . 178,183 Compact Disc Maintenance . . . . . . . . . . . . . . . . . 168 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Compass Calibration . . . . . .
INDEX 335 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . . 63 Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 244 Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Used Coolant . . . . . . . . . . . . . . . . . . . . . . . . . 269 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Oil Pressure Gauge . . . . . . . . . . . . . . . . . . . . . 145 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 295 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 145 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . .
INDEX 337 Front Axle . . . . . . . Fuel . . . . . . . . . . . Filler Cap . . . . . . Filter . . . . . . . . . Gasoline . . . . . . Gauge . . . . . . . . Materials Added . Octane Rating . . Requirements . . . Tank Capacity . . Fuel System Caution Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 . . . . . . . . . . . . . . . . . . . . . . 222 . . . . . . . . . . . . . . . . . . . . . . 226 . . . . . . . . . . . . . . . . . . . . . . 260 . . . . . . . . . . . . . . . . . . . . . .
INDEX Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 180 High Beam Indicator . . . . . . . . . . . . . . . . . . . . . 144 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271,272 Hydraulic Clutch Fluid . . . . . . . . . . . . . . . . . . . . 276 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 339 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 222 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33,145 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Anti-Lock Warning . . . . . . . . . . . . . . . . . . . . . 147 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 147 Bulb Replacement . .
INDEX Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 37,38 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 264 Maintenance, Airbag . . . . . . . . . . . . . . . . . . . . . . 33 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 261 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 253 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 300 Schedule ⬙A⬙ . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 341 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Identification Logo . . . . . . . . . . . . . . . . . . . . . 255 Materials Added to . . . . . . . . . . . . . . . . . . . . . 257 Recommendation . . . . . . . . . . . . . . . . . . . 255,295 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . 256,295 Onboard Diagnostic System . . . . . . . . . . . . . . 250,251 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 54 Overheating, Engine . . . . . . . . . .
INDEX Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 232 Shifting into Transfer Case Neutral (N) . . . . . . . 232 Shifting out of Transfer Case Neutral (N) . . . . . 233 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 223 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 Release, Hood . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 343 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 255 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 16 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . 16 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 322 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 324 Service Manuals .
INDEX Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 290 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . 290 Supplemental Restraint System - Airbag . . . . . . . . 27 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Temperature Gauge, Engine Coolant . . . . . . . . . . 145 Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 37 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . . 66 Tire and Loading Information Placard . . .
INDEX 345 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Four-Wheel-Drive Operation . . . . . . . . . . . . . . 191 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Maintenance . . . . . . . . . . . . . . . . . . . . . . . 274,276 Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Shifting . . . .
INDEX Windshield, Folding . . . . . . . . . . . . . . . . . . . . . . 130 Windshield Washers . . . . . . . . . . . . . . . . . . . . 64,265 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 265 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 64 Wiper, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
