SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 7 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeep威 Grand Cherokee SRT8 and welcome to our worldwide family. Before you start to drive this vehicle, read this manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering and transmission shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. Always observe federal, state, provincial, and local laws wherever you drive.
INTRODUCTION Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury. Drive carefully. 5 Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S.
INTRODUCTION NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar威 parts, and is interested in your satisfaction.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .12 䡵 Doors And Door Locks . . . . . . . . . . . . . . . . . . . .16 ▫ Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .13 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .19 䡵 Sentry Key Immobilizer System . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Battery Service . . . . . . . . . . . . . . .24 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .33 䡵 Security Alarm System — If Equipped . . . . . . . . .25 ▫ Lap/Shoulder Belt Operating Instructions . . . . .34 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .25 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .37 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 11 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Ignition Key Insert the key fully, then turn the switch to one of the four illustrated positions. The key can be inserted or withdrawn only in the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder If the driver’s door is opened when the key is in the ignition and not turned to the ON position, a chime will sound to remind you to remove the key. CAUTION! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. SENTRY KEY IMMOBILIZER SYSTEM The Sentry Key Immobilizer System (SKIM) prevents unauthorized operation of the vehicle by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the SKIM indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key Immobilizer System complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. ILLUMINATED ENTRY The interior lights come on when you open any door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! CAUTION! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. 19 If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit Feature — Only Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in P (Park) or N (Neutral). Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 of this manual or see your authorized dealer. NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors Press and release the “Unlock” button on the transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash twice to acknowledge the unlock signal. The illuminated entry system also turns on. NOTE: If desired, the system can be programmed to unlock all doors on the first press of the “Unlock” button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Release the Liftgate Flipper Glass Press the “Flipper Glass/Trunk Release” button on the transmitter two times to release the flipper glass. WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn Off “Flash Lights On Lock/Unlock” NOTE: If desired, the “Flash Lights On Lock/Unlock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 23 General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, remove the small screw, and separate the two halves of the transmitter. Make sure not to damage the rubber gasket during removal. Separating Transmitter Halves 2. Remove and replace the battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, join the two halves of the case together. Install and tighten the screw until snug. Make sure there is an even “gap” between the two halves. Test transmitter operation. SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE system is armed (after 16 seconds), when you pull the door handle to exit the alarm will sound. If this occurs, press the “Unlock” button on the remote keyless entry transmitter to disarm the system. The Security Alarm System will not disarm with a manual unlock, either through the lock plunger located on the inside of the door, or through a key in the driver’s door key cylinder. LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. 2 Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! To avoid injury stand back when opening. Glass will automatically rise. Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 POWER WINDOWS The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. 2 Power Window Switches The power window switches remain active for up to 10 minutes after the ignition switch has been turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. 2 Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up: Pull the window switch up and close the window completely, then pull and hold the switch for 1 second.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle 35 WARNING! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! 37 Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chime and flash the Seat Belt Warning Light for 96 seconds or until the driver or front passenger seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver or front passenger seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS/AIRBAG. Window Airbag Location 43 NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with window bags, do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Restraint Control Module • Driver and Front Passenger Seat Belt Pretensioner • Occupant Classification System (OCS) — Front Passenger Seat Only (If Equipped) • Airbag Warning Light − Occupant Classification Module • Driver Airbag − Passenger Airbag Disable (PAD) Indicator Light • Passenger Airbag − Weight Sensors • Side Curtain Airbags above Side Windows (If Equipped) • Side
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (If Equipped) (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The “PAD Indicator Light” should not be illuminated when teenagers, most children in a forward-facing child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passenger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occurs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE both the “PAD Indicator Light” and the “Airbag Warning Light” are illuminated to show that the passenger airbag is turned off until the fault is cleared. If an object is lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the “PAD Indicator Light” and the “Airbag Warning Light.” Once the lodged object is removed, the fault will be automatically cleared after a short period of time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Your vehicle has four Weight Sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Side Impact SRS Side Curtain Airbags are designed to activate only in certain side or rollover collisions. When the ORC (with side impact option) detects a collision requiring the side curtain airbag to inflate, it signals the inflators on the crash side of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The following requirements must be strictly adhered to: • Do not modify the front passenger seat assembly or components in any way. • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy when the Occupant Restraint Control (ORC) Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioner, and seat belt retractor assembly, replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • Does not come on during the 6 to 8 seconds after the ignition switch is first turned on. • Remains on after the 6 to 8 second interval. • Comes on for any period of time while driving.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating position. • Buckle the child into the restraint exactly as the manufacturer’s instructions tell you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Tether Strap Mounting Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ Operations . . . . . . . . . . . . . . . . . . . . . . . . . . .84 ▫ Inside Automatic Dimming Mirror . . . . . . . . . .78 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .90 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .79 ▫ UConnect™ System Features . . . . . . . . . . . . . .93 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Lumbar Support Adjustment . . . . . . . 106 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 107 ▫ Interior Lighting . . . . . . . . . . . . . . . . . . . . . . 118 ▫ 8 - Way Driver’s Power Seat . . . . . . . . . . . . . . 108 ▫ Front Map/Reading Lights . . . . . . . . . . . . . . 119 ▫ 4 - Way Passenger’s Power Seat — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ ERM (Electronic Rollover Mitigation) . . . . . . . 133 ▫ High Beam Switch . . . . . . . . . . . . . . . . . . . . 125 ▫ ESP (Electronic Stability Program) . . . . . . . . . 134 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ ESP/BAS Warning Lamp And ESP/TCS Indicator Light . . . . . . . . . . . . . . . . 137 ▫ Headlight Time Delay . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Set At a Desired Speed . . . . . . . . . . . . . . . 146 ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 155 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Reprogramming a Single Homelink Button . . . 156 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 147 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 159 ▫ Retractable Cargo Area Cover . . . . . . . . . . . . 164 䡵 Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . . . 165 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . 167 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Automatic Dimming Mirror This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Outside Automatic Dimming Mirror — If Equipped If your vehicle is equipped with a driver’s outside automatic dimming mirror, it operates when the inside automatic dimming mirror is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. After selecting a mirror move the knob in the same direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this section for details. Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors. 3 Lift the cover to reveal the mirror. The light will turn on automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. 83 The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operations Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. NOTE: • www.chrysler.com/uconnect Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Before attempting to pair phone, please see your cellular phone’s user manual (Bluetooth section) for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Call.⬙ • System will prompt you to say the name of the person you want call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. four associated phone numbers and designations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the ⬙Phonebook Edit⬙ feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the mobile phone is reachable: The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. • Pick up the phone and manually dial the emergency number for your area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour “Towing Assistance” coverage details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing ⬙Would you like to pair a phone, clear aѧ,⬙ you could press the ’Voice Recognition’ button and say ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted say the priority number of the cellular phone you wish to select. You can also press the ⬘Voice Recognition’ button anytime while the list is being played, then say the priority number of the phone that you wish to select. • The selected phone will be used for the next phone call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity, echo. and loudness to a large degree, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. 101 Bluetooth Communication Link Cellular phones have been found to occasionally lose connection to the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up Phone settings phone set up 105 SEATS WARNING! Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 button which must be pushed in to lower the head restraint to all positions. The restraints may be raised without pushing in the button. 3 Manual Lumbar Control Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8 - Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicate the level of heat in use. Two LEDs are illuminated for high, one for low, and none for off. Pressing the switch once will select high-level heating. 109 When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 1. Pull the release strap (toward the front of the vehicle) to release. Rear Seat Release NOTE: Do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. NOTE: The automatic folding rear head restraints will lower as the seat is folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat Raise the rear seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. The automatic folding rear head restraints must be manually returned from the folded position to the raised seating position. Storage — Rear Seat Armrest (If Equipped) The rear seat may be equipped with a center storage armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the latch and lift the top of the armrest to access the storage bin. DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the “Unlock” button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle may have been delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up to four transmitters, each one linked to either of the two memory positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Insert the ignition key and turn the ignition switch to the ON position. 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter ⬙Yes⬙ or select ⬙Use Factory Settings⬙ from the EVIC and enter ⬙Yes⬙. Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 for more information. 12.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Disable A Transmitter Linked to Memory 1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release memory button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to step 3. 3. Press and release the memory SET (S) button located on the driver’s door. 4. Within 5 seconds, press and release memory button 1 on the driver’s door. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The seat shall move to the position located 1 1/8 inches (30 mm) forward of the rear stop if the starting position is between 2.5 inches to 3.75 inches (60 mm to 90 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/driving position when the key is placed into the ignition, and turned out of the LOCK position toward the RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. 117 Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. LIGHTS Interior Lighting The interior lighting consists of courtesy lights mounted below the instrument panel, an overhead console light assembly which contains both driver and passenger reading lights, reading lights located above the rear doors, and a rear cargo light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Multi-Function Control Lever Turn Signal Auto-Mode — If Equipped Tap the multi-function control lever once and the turn signal (left or right) will flash 3 times, and automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights and Parking Lights Turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for “Auto” headlight operation (if equipped). 121 Automatic Headlight System — If Equipped Turn the end of the multi-function control lever to the third detent to activate the automatic headlight system. This system performs two functions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If your vehicle is equipped with a “Rain Sensitive Wiper System,” and it is activated, the headlights will automatically turn on after the wipers complete five wipe cycles within approximately 1 minute, and they will turn off approximately four minutes after the wipers completely stop. Refer to “Windshield Wipers and Washers” in this section for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate 1. Pull back on the muti-function control lever to manually deactivate the system (normal operation of high beams). 2. Pull back on the multi-function control lever once again to re-activate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — Canada Only The high beam headlights come on at a low intensity level whenever the engine is running, and the transmission in not in the P (Park) position. The lights remain on until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam Switch Pull the multi-function control lever towards you to switch the headlights to “High” beam. The “High Beam Indicator Light” on the instrument cluster will illuminate. Pull the multi-function control lever a second time to switch the headlights to “Low” beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multi-function control lever toward the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “Speed Sensitive Intermittent Wiper System” in this section. For information on the rear wiper and washer, refer to “Rear Window Features” in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of five settings to activate this feature. Rain Sensitive Wiper Switch The sensitivity of the system can be adjusted with the multi-function lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system. NOTE: • The rain sensing feature will not operate when the wiper switch is in the LOW or HIGH speed position. • The rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • Use of Rain-X威 or products containing wax or silicone may reduce rain sensor performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Tilt Steering Column WARNING! Tilting the steering wheel column while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ABS (Anti-Lock Brake System) This system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in Section 5 of this manual for more information about ABS.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TCS (Traction Control System) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or roll overs, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ⬙ESP/TCS Indicator Light⬙ located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ESP/TCS Indicator Light⬙ also flashes when TCS is active. If the ⬙ESP/TCS Indicator Light⬙ begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ESP system has 2 available operating modes. On This is the normal operating mode for ESP. Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most all driving situations. ESP should only be turned to “Partial Off” for specific reasons as noted below. Partial Off This mode is entered by momentarily depressing the ⬙ESP Control Switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “ESP Partial Off” mode by pressing the ESP switch. Once the situation requiring ESP to be switched to the “ESP Partial Off” mode is overcome, turn ESP back on by momentarily depressing the “ESP Control Switch.” This may be done while the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM— IF EQUIPPED The Rear Park Assist System provides visual and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to the Warning Section and Note Section for limitations of this system and recommendations. The Rear Park Assist System will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the flipper glass, provides both visual and audible warnings to indicate the distance between the rear fascia and the detected obstacle. 139 When the ignition is changed to the RUN/ON position, the warning display will turn ON all of its LEDs for about 1 second. Each side of the warning display has 6 yellow and 2 red LEDs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the detected obstacle is about 11.8 inches (30 cm) from the rear fascia, the warning display will actuate a continuous tone for about 10 seconds, and it will turn ON all 8 LEDs, including both RED LEDs, on the corresponding side of the display. The radio will be muted while the tone is actuated. When the obstacle is less than 11.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message. The Rear Park Assist Switch LED will be ON when the Rear Park Assist System is disabled or defective. The Rear Park Assist Switch LED will be OFF when the system is enabled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • The Rear Park Assist System is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when the obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Clean all four Rear Park Assist Sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The system might not detect an obstacle behind the fascia or it could provide a false indication that an obstacle is behind the fascia. Assure objects are not within 11.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Press the left side of the button to move the pedals rearward (toward the driver). CAUTION! Press the right side of the button to move the pedals forward (away from the driver). Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator operations at speeds greater than 25 mph (40 km/h). The controls are mounted on the steering wheel and consist of ON·OFF, SET, RES·ACCEL, CANCEL, and DECEL controls. To Activate Press the ON·OFF button to turn the system ON. To turn the system OFF, press the ON·OFF button again. The system should be turned OFF when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed To resume a previously set speed, press and release the RES·ACCEL button. Resume can be used at any speed above 25 mph (40 km/h). To Vary the Speed Setting When the Speed Control is ON, speed can be increased by pressing and holding the RES·ACCEL button. When the button is released, a new set speed will be established. Tapping the RES·ACCEL button once will result in a 1 mph (2 km/h) speed increase.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, and optional power sunroof switches. 149 Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door or rear door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed. NOTE: The HomeLink威 Universal Transceiver is disabled when the Vehicle Theft Alarm is active.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 3 The Electronic Vehicle Information Center (EVIC) features a driver-interactive display which includes HomeLink system messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and release only when the EVIC display shows “CHANNELS CLEARED” (after 20 seconds). Do not hold the buttons for longer than 30 seconds and do not repeat step one to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until step 4 has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The EVIC display will show “CHANNEL X TRAINING” (where X is Channel 1, 2, or 3).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink button while you press and release every two seconds (⬙cycle⬙) your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. The EVIC display will show “CHANNEL X TRAINED” (where X is Channel 1, 2, or 3). Proceed with ⬙Programming⬙ step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. Press and hold the desired HomeLink button. Do NOT release the button. • This device may not cause harmful interference. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch 157 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER OUTLET To the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. The rear power outlet (if equipped) is located in the left rear cargo area. Rear Power Outlet Front Power Outlet The power outlets are a direct feed from the battery so they receive power whether the ignition is in the ON or OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE All accessories connected to this outlet should be removed or turned off when the vehicle is not in use to protect the battery against discharge. 161 CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS In the center console there are two cup holders for the front seat passengers. cup depression towards the passenger seat, but the top surface will not be flush with the console surface. The rear passengers have access to two cup holders that pull out from the lower center of the rear seat. Front Cup Holders NOTE: The cup holder insert is removable, from the console, for cleaning.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the liftgate is open, pushing on the cargo light lens surface will turn off all interior lamps. Push on the lens surface a second time to restore the interior lights to normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. Cargo Tie-Down Hooks The tie-downs located on cargo area floor should be used to safely secure loads when vehicle is moving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. WARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. 3 Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. the wash function. The wash pump will continue to operate as long as the button is pressed. Upon release, the wipers will cycle three times before returning to the set position. 3. Lift tray over loop(s), and reposition tray. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “Park” position. If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Interior Controls . . . . . . . 174 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 197 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 197 䡵 Instrument Cluster Description . . . . . . . . . . . . . 176 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 197 䡵 Electronic Vehicle Information Center . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions (CD Mode For CD Audio Play) . . . . . . . . . . . 204 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . 205 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 207 ▫ Operation Instructions (CD Mode For MP3 Audio Play) . . . . . . . . . . 210 ▫ Load/Eject Button (CD Mode For MP3 Play) . . 210 䡵 Sales Code REC — AM/FM/CD (6–Disc) Radio With Navigation System . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 173 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Summer Operation . . . . . . . . . . . . . . . . . . . . 228 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Winter Operation . . . . . . . . . . . . . . . . . . . . . 228 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 221 ▫ Vacation Storage . . . . . . . . . . . . . . . . . . . . . . 229 䡵 Radio Operation And Cellular Phones . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND INTERIOR CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 175 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light The BRAKE warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light stays on longer, it may be an indication that the parking brake has not been released.
UNDERSTANDING YOUR INSTRUMENT PANEL engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 8. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL prevailing road conditions. The “ESP/TCS Indicator Light” will flash any time the ESP or TCS is active and helping to improve vehicle stability. If the “ESP/TCS Indicator Light” is on solid, the ESP system has been turned off by the driver or a temporary condition exists that will not allow full ESP function. (See page 130 for more information.) 12.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Vehicle Information Center Display When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to “Electronic Vehicle Information Center” later in this section. 15. Electronic Stability Program (ESP) Warning Light/Brake Assist System (BAS) Warning Light — If Equipped The ESP/BAS warning light in the instrument cluster comes on when the ignition switch is turned to the “ON” position.
UNDERSTANDING YOUR INSTRUMENT PANEL U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 19. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 20.
UNDERSTANDING YOUR INSTRUMENT PANEL 22. Front Fog Light Indicator Light— If Equipped This light shows the front fog lights are ON. 183 ELECTRONIC VEHICLE INFORMATION CENTER 23. Voltage Warning Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL • PERFORM SERVICE • LIFTGATE/DOORS OPEN (with graphic) • KEY NOT PROGRAMMED — DAMAGED KEY • LIFTGLASS OPEN (with graphic) • KEY NOT PROGRAMMED — INVALID KEY • HOOD OPEN (with graphic) • KEY NOT PROGRAMMED — EXCEEDED KEY PROGRAM LIMIT • HOOD/DOOR OPEN (with graphic) • PROGRAMMING ACTIVE — NEW KEY PROGRAMMED • SERVICE SECURITY KEY • INVALID KEY — TRY ALTERNATE KEY • DRIVER/PASSENGER DOOR OPEN (with graphic) • LEFT/RIGHT REAR DOOR OPEN (with graphic) • X DOORS
UNDERSTANDING YOUR INSTRUMENT PANEL 185 • WASHER FLUID LOW (with graphic) • MEMORY #2 POSITIONS SET • UPSHIFT (with graphic) • MEMORY SYSTEM DISABLED — SEATBELT FASTENED (with graphic) • CHECK GAUGES • AUTO HIGHBEAM ON • AUTO HIGHBEAM OFF • PARK ASSIST DISABLED • SERVICE PARK ASSIST SYSTEM • TRANSMISSION OVER TEMP • LOW BRAKE FLUID LEVEL • WARNING! LIMIT SPEED • CHECK GAS CAP • ESP OFF • MEMORY #1 POSITIONS SET • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • DRIVER 1 MEMORY • DRIVER 2 MEMORY • PEDAL
UNDERSTANDING YOUR INSTRUMENT PANEL • LEFT REAR LOW PRESSURE Customer Programmable Features Press the MENU button until one of the display choices following appears: Language? When in this display you may select one of three languages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display selects English, Espanol, or Francais. As you continue the displayed information will be shown in the selected language.
UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL memory set position using the door mounted switch. Pressing the STEP button when in this display will select “Yes” or “No.” Sound Horn With Lock? When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL this display will select “Low Beam” or “Low/High Beam.” Refer to “Lights — SmartBeams” in Section 3 of this manual. NOTE: System will activate at or above 20 mph (32 km/h). Headlamps On With Wipers? (Available with Auto Headlights Only) When this feature is selected and the headlight switch has at least once been moved to the A (Auto) position, the headlights will turn on when the wipers are turned on.
UNDERSTANDING YOUR INSTRUMENT PANEL Easy Entry/Exit Seat? (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. The Easy Entry/ Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/ Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING YOUR INSTRUMENT PANEL 191 WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING YOUR INSTRUMENT PANEL Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
UNDERSTANDING YOUR INSTRUMENT PANEL Reset Button Press the RESET button to reset the display you are in. Press and hold the RESET button (for 2 seconds) to reset all of the displays. 193 Distance To Empty Shows the estimated distance that can be travelled with the fuel remaining in the tank. This is calibrated using the miles per gallon during the last driving period. Trip A Shows the total distance travelled for trip A since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Engine Oil Temperature Shows the current engine oil temperature. The scale will read from 140° – 300°F (60° – 149°C). Tire Pressure Display Shows the current pressure of all 4 road tires. NOTE: Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures” in Section 5 for additional information.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass. Refer to Variance Map. To Put Into a Calibration Mode Start the engine, and leave the transmission in the P (Park) position. Set the display to “Compass/ Temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the C/T button approximately 5 seconds. The last variance zone number will be displayed. Press and hold the STEP button for 1 second to select the new variance zone and press the RESET button to resume normal operation. Two Types of Signals There are two basic types of radio signals...
UNDERSTANDING YOUR INSTRUMENT PANEL FM Reception Because FM transmission is based on frequency variations, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: On vehicles so equipped the radio, steering wheel radio controls and 6 disc CD/DVD changer will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Roc
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) CAUTION! NOTE: The ignition switch must be in the ON or ACC position to operate the radio. This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
UNDERSTANDING YOUR INSTRUMENT PANEL MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the MSG or INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual. SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to separate Video Entertainment System (VES威) Guide.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit.
UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The DVD player is mounted in the rear of the center console storage bin, and is concealed by a door that lifts up for access. Refer to your VES™ User’s Manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 The LCD screen is located on the headliner behind the front seats.
UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers over 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RAQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • The current program type and channel number will then be displayed for 5 seconds. • The current channel number will then be displayed until an action occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. Using the PTY (Program Type) Button — If Equipped Follow the PTY button instructions that apply to your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. 4 • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Automatic Temperature Control The Infrared Dual-Zone Climate Control System automatically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face of the control unit.
UNDERSTANDING YOUR INSTRUMENT PANEL LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once the comfort level is selected the system will maintain that level automatically using the heating system.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off until the engine warms up.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 4
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions.
UNDERSTANDING YOUR INSTRUMENT PANEL Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • Panel Air flows through the outlets located in the instrument panel. Air flows through the registers in the back of the center console to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The recirculation mode should only be used temporarily. The button includes an LED that illuminates, which indicates that the recirculation mode is active. You may use this feature separately. NOTE: Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the “Recirculate” icon button to return to outside air.
UNDERSTANDING YOUR INSTRUMENT PANEL Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 234 䡵 AutoStick . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 234 ▫ AutoStick Operation . . . . . . . . . . . . . . . . . . . 240 ▫ Extreme Cold Weather (Below –20°F (–29°C) . . 235 ▫ AutoStick General Information . . . . . . . . . . . . 241 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 235 䡵 Parking Brake . . . . .
STARTING AND OPERATING ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 252 ▫ Premium System . . . . . . . . . . . . . . . . . . . . . . 265 䡵 Tires — General Information . . . . . . . . . . . . . . . 256 ▫ General Information . . . . . . . . . . . . . . . . . . . 268 ▫ Run Flat Tires . . . . . . . . . . . . . . . . . . . . . . . . 256 䡵 Tire Rotation Recommendations . . . . . . . . . . . . 268 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 257 䡵 Fuel Requirements . . .
STARTING AND OPERATING 233 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 274 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 278 ▫ Common Towing Definitions . . . . . . . . . . . . . 275 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 280 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . . 277 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 284 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal starting procedure. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be in the N (Neutral) or P (Park) position before you can start the engine.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme Cold Weather (below –20°F (–29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended.
STARTING AND OPERATING After Starting The idle speed will automatically decrease as the engine warms up. vehicle, may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should apply the park brake, shift the transmission into P (Park), and remove the key from the ignition. Once the key is removed from the ignition the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING NOTE: The Electronic Stability Program (ESP) and Traction Control (if equipped) should be turned OFF before attempting to rock the vehicle. Refer to “Electronic Brake Control System” in Section 3 of this manual. The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
STARTING AND OPERATING Autostick Operation By placing the shift lever in the D (Drive) position the lever can be moved from side to side. This allows the driver to engage the AutoStick mode. Moving the shift lever to the right (+) or the left (-) will engage the Autostick mode. In normal driving mode (Boxed “D” displayed in the PRNDL), moving the shift lever to the right (+) will engage the Autostick mode putting the transmission in the currently engaged gear.
STARTING AND OPERATING upshift, the engine control system will limit the engine speed to protect the engine. Refer to “Electronic Vehicle Information Center” in Section 4 of this manual. Shifting into or out of the Autostick mode can be done at any time without taking your foot off the accelerator pedal. When the driver wishes to engage Autostick, simply move the shift lever to the Left or Right (D-/D+) position while in D (Drive).
STARTING AND OPERATING NOTE: The instrument cluster “Brake Warning Light” indicates only that the parking brake is applied. It does not indicate the degree of brake application. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the P (Park) position. Make certain the transfer case is in gear. Failure to do so may cause the vehicle to roll and cause damage or injury.
STARTING AND OPERATING WARNING! • Leaving children unattended in a vehicle is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING The Anti-Lock Brake System conducts a low-speed selftest at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring you may feel slight pedal movement. The movement can be more apparent on ice and snow. This is normal. The Anti-Lock Brake System pump motor runs during the self-test at 12 mph (20 km/h) and during an ABS stop. The pump motor makes a low humming noise during operation, which is normal.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning.
STARTING AND OPERATING • Do not drive too fast for road conditions, especially when roads are wet or slushy. A wedge of water can build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. 247 TIRE SAFETY INFORMATION Tire Markings CAUTION! 5 Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the power steering pump may occur. NOTE: • P (Passenger)-Metric tire sizing is based on U.S.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 249 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 251 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING 255 5
STARTING AND OPERATING WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Do not exceed 55 mph (88 km/h) if the “Tire Pressure Monitoring Telltale Light” is illuminated. Vehicle handling and braking may be reduced. You could have an accident and be severely or fatally injured.
STARTING AND OPERATING Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 257 1. Safety— WARNING! Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper cold tire inflation pressure is listed on either the face of the driver’s door, or the driver’s side “B” pillar. 3.
STARTING AND OPERATING 259 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your dealer for radial tire repairs.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! All tires should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury. Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. 263 Replacement Tires The tires on your new vehicle provide a balance of many characteristics.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE PRESSURE MONITOR SYSTEM (TPMS) Premium System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
STARTING AND OPERATING The system consists of tire pressure monitoring sensors attached to each wheel through the valve stem mounting hole, a central receiver module, Wheel Sensor Trigger Modules mounted in three of the four wheel wells, various Tire Pressure Monitoring System Display Messages in the EVIC, and a “Tire Pressure Monitoring Telltale Light.
STARTING AND OPERATING CHECK TPM SYSTEM See your authorized dealer when this message appears in the EVIC. This message indicates that a system fault condition has been detected. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. The tire pressure sensors are covered under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . .
STARTING AND OPERATING 269 Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. FUEL TANK FILLER CAP (GAS CAP) The fuel cap is located on the left side of the vehicle.
STARTING AND OPERATING 273 CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • Turn the engine off.
STARTING AND OPERATING WARNING! WARNING! • Remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ GVWR (Gross Ve- GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Tongue Transmission hicle Wt. Rating) bined Wt. Rating) Trailer Wt.) Wt. (See Note 1) 6.1L Auto5,650 lbs (2 563 kg) 8,800 lbs (3 992 kg) 40 Sq. Ft. (3.
STARTING AND OPERATING Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. 279 Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle in P (Park). Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded.
STARTING AND OPERATING − When replacing tires, refer to “Tires–General Information” for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements — Trailer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury.
STARTING AND OPERATING 283 WARNING! NOTE: Do not cut or splice wiring into the vehicles wiring harness. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Highway Driving Reduce speed. − Don’t use in hilly terrain or with heavy loads. − Air Conditioning Turn off temporarily. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . . 288 䡵 Jump Starting Procedure . . . . . . . . . . . . . . . . . . 289 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not to be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set the parking brake, place the transmission in P (Park), and turn the ignition to OFF for both vehicles. 3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! Jump starting can be dangerous. To avoid personal injury or damage to electrical components in vehicle, observe the following warnings: • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin, or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 6.1L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 304 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 297 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 297 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 310 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 311 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 312 ▫ Windshield Washers — Front And Rear . . . . . 312 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 319 ▫ Brake System . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 295 ▫ Center High Mounted Stop Light (CHMSL) . . . 340 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 341 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . .
MAINTAINING YOUR VEHICLE 6.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. 301 NOTE: Fill engine oil one quart at a time. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). CAUTION! Operating the engine with the oil levels below the safe zone, or operating with oil levels that exceed the top of the safe zone may cause engine damage.
MAINTAINING YOUR VEHICLE 303 NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that are API rated as SM/CF and meet the requirements of DaimlerChrysler Material Standard MS-10725. Use Mopar or an equivalent oil meeting the specification MS-10725.
MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
MAINTAINING YOUR VEHICLE 305 Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Malfunctioning spark plugs can damage the catalytic converter. For proper type of replacement spark plugs, refer to the “Vehicle Emission Control Information” label in the engine compartment.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery. To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. 309 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the appropriate “Maintenance Schedule,” the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator.
MAINTAINING YOUR VEHICLE 319 ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE WARNING! Insure nylon tubing in these areas has not melted or collapsed. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE 321 should be replaced immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failure. Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. WARNING! Overfilling of fluid is not recommended because it may cause leaking in the system. Worn brake hoses can burst and cause brake failure. You could have an accident.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended MOPAR DOT 3 product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service. Automatic Transmission Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
MAINTAINING YOUR VEHICLE CAUTION! The fluid level is preset at the factory and does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your authorized dealer has the proper tools to accurately adjust the fluid level. Fluid and Filter Changes Automatic transmission fluid and filter should be changed as follows: Maintenance Schedule “A” — No change necessary.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner.
MAINTAINING YOUR VEHICLE • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar威 Touch Up Paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar威 Total Clean to clean fabric upholstery and carpeting. Interior Trim should be cleaned starting with a damp cloth, a damp cloth with Mopar威 Total Clean, then Mopar威 Spot & Stain Remover if absolutely necessary.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
MAINTAINING YOUR VEHICLE Cavity 4 5 6 7 8 9 Fuse Panel Location Cavity 1 2 3 Fuse/Color 30 Amp Green 15 Amp Blue 10 Amp Red Description Audio Amp (B+) Sunroof (B+) Htd Mirror (EBL) 10 11 12 13 14 15 Fuse/Color 20 Amp Yellow 10 Amp Red 10 Amp Red 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 10 Amp Red Spare 10 Amp Red Spare 20 Amp Yellow 10 Amp Red 329 Description Rr Pwr Out (B+) Rr HVAC (R/O) OCM (B+) Door Locks (B+) Steer Col Lock (B+) Pwr Outlet (B+) Ign Run Only Out (R/O) Mem.
MAINTAINING YOUR VEHICLE Cavity 16 17 19 20 21 22 24 25 Fuse/Color 10 Amp Red 15 Amp Blue 10 Amp Red 10 Amp Red 15 Amp Blue 15 Amp Blue 10 Amp Red 10 Amp Red CB1 CB2 CB3 20 Amp 20 Amp 20 Amp Description SCM, Cluster OBD (B+) Flipper Glass (B+) OCM (R/S) WCM, Cluster (R/S) Autowipe (Accy Delay) Rear Wiper (B+) PDC, FCM, A580 (R/S) ABS, Trans.
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Fuse/Color 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink Spare 50 Amp Red Spare 40 Amp Green Spare 40 Amp Green 30 Amp Pink 40 Amp Green 40 Amp Green Spare Spare Description HVAC Blower Power Outlets Rr Wiper/Ign R/O ABS Pump ASD Acc Delay/Seats Starter/JB Power Cig Ltr/T-Tow EBL/Htd Mirror JB Power Cavity 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Fuse/Color 25 Amp Natural Spare 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 30 Amp Pink
MAINTAINING YOUR VEHICLE Cavity 30 31 32 33 34 35 36 38 39 40 Fuse/Color Spare Spare Micro Relay Micro Relay Micro Relay Micro Relay Spare Spare Mini Relay Mini Relay Description Underhood Fuses (Integrated Power Module) TCM Rly (Gasoline Only) Starter Rly AC Clutch Rly Fuel Pump Rly HVAC Blower Rly ASD Rly Integrated Power Module
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Fuse/Color Micro Relay Micro Relay Micro Relay Spare Micro Relay Micro Relay Micro Relay 10 Amp Red 10 Amp Red 10 Amp Red Mini Relay 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly Lt T-Tow Stop/Turn Rly Rt T-Tow Stop/Turn Rly Park Lamps Rly Lt Park Lamps T-Tow Park Lamps Rt Park Lamps Rad Fan Hi Rly FCM Batt #4 FCM Batt #2 Adjustable Pedal Ft Fog Lamps Horn
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • Remove fuse #27 in the Intelligent Power Module labeled Ignition-Off Draw (IOD#1). • Or, disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
MAINTAINING YOUR VEHICLE Exterior Lights Bulb Type Backup Lights . . . . . . . . . . . . . . . . . . . . . . . . . 3157K Front Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . 9145 Front Park/Turn Light . . . . . . . . . . . . . . . . . . . 3157K Front Side Marker . . . . . . . . . . . . . . . . . . . . . . . 2825 Headlights (Low Beam) . . . . . . . . . . . . . . . . . . . 9006 Headlights (High Beam) . . . . . . . . . . . . . . . . . . . 9005 Rear License Plate Light. . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. 4. Disconnect the electrical connector and replace the bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
MAINTAINING YOUR VEHICLE 337 Front Turn Signal 1. Open the hood. 2. Remove the headlamp cover. 4. Disconnect the electrical connector and replace the bulb. 3. Turn the turn signal bulb 1/4 turn counter clockwise to remove from housing.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2.
MAINTAINING YOUR VEHICLE 339 Rear Tail, Stop, Turn Signal, and Back-Up Lights 1. Raise the liftgate. 2. Remove the two Torx fasteners. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly. 3. Squeeze the socket assembly tabs to remove it from the housing.
MAINTAINING YOUR VEHICLE Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
MAINTAINING YOUR VEHICLE 341 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 6.1 Liter Engine (SAE 0W-40, API Certified) Cooling System * 6.1 Liter Engine (Mopar威 Engine Coolant/Antifreeze 5 Year/ 100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 20.6 Gallons Metric 78 Liters 7 Qts 6.6 Liters 14.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (6.1L Engine) Oil Filter (6.1L Engine) Spark Plugs Fuel Selection (6.1L Engine) Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SM/CF synthetic engine oil. SAE 0W-40 is recommended, meeting the requirements of DaimlerChrysler Material Standard MS-10725.
MAINTAINING YOUR VEHICLE 343 Chassis Component Automatic Transmission Transfer Case Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid Castrol威 BOT89 M1 Plus Lubricant Usage of other fluid/lubricants is NOT recommended. Mopar威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent. Mopar威 DOT 3 Brake Fluid, SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 346 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 349 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 346 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 346 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 347 M NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” CAUTION! NOTE: If ANY of these apply to you, change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance recommendations in “Maintenance Schedule B.” Failure to perform the required maintenance items may result in damage to the vehicle.
M A I N T E N A N C E S C H E D U L E S 8 348 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect brake hoses.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
M 350 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the engine air cleaner filter, replace if necE essary. S C H E D U L E S 8 Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Drain and refill the front and rear axles. Inspect the brake linings. Drain the transfer case and refill.
M 352 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the engine air cleaner filter, replace if necE essary. S C H E D U L E S 8 Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Inspect drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axles. Drain and refill the transfer case fluid. Drain and refill the automatic transmission fluid, and replace filter. Flush and replace engine coolant/anti-freeze.
M 354 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the engine air cleaner filter, replace if necE essary. S C H E D U L E S 8 Inspect the drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axle fluid.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary.* Drain and refill the transfer case fluid. Inspect the brake linings. Drain and refill the front and rear axle fluid.
M 356 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the engine air cleaner filter, replace if necE essary. S C H E D U L E S 8 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Flush and replace the engine coolant/anti-freeze, if not done at 60 months.
SCHEDULE “B” Miles 108,000 (Kilometers) (180 000) Change the engine oil and engine oil filter, if not replaced X at 3 months. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary.* Inspect the brake linings. X Drain and refill the front and rear axle fluid. Drain and refill the automatic transmission fluid, and replace filter. Drain and refill the transfer case fluid.
M 358 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change the engine oil and engine oil filter. E Inspect the engine air cleaner filter, and replace if S C H E D U L E S 8 necessary. Inspect the brake linings. Drain the transfer case and refill.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the brake linings.
M 360 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Inspect the engine air cleaner filter, and replace if necE essary. S C H E D U L E S 8 Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary. Flush and replace the engine coolant/anti-freeze at 60 months, if not replaced at 102,000 miles (170 000 km). Inspect the brake linings. Drain the transfer case and refill.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not replaced at 60 months. Drain the transfer case and refill.
M 362 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Inspect the engine air cleaner filter, and replace if necessary. E Inspect the PCV Valve, replace if necessary.〫 S C H E D U L E S 8 Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not done at 102,000 miles (170 000 km). Drain the transfer case and refill.
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Prepare For The Appointment . . . . . . . . . . . . 366 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 366 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 366 䡵 Warranty Information (U.S. Vehicles Only) . . . . . 369 䡵 Mopar威 Parts . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 371 Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 177,243 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 316 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 169 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 270 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 144 Air Conditioner Maintenance . . . . . . . . . . . . . . . 309 Air Conditioning Refrigerant . . . . . . . . . . . . . . . 310 Air Pressure, Tires . . . . . . . . . . . . . . . .
INDEX Emergency Starting . . . . . . . . . . . . . . . . . . . . . 289 Keyless Transmitter Replacement (RKE) . . . . . . . 24 Saving Feature (Protection) . . . . . . . . . . . . . . . 120 Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Body Mechanism Lubrication . . . . . . . . . . . . . . . 311 B-Pillar Location . . . . . . . . . . . .
INDEX Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Child Restraint . . . . . . . . . . . . . . . . . . . . . . 59,65,67 Child Restraint Tether Anchors . . . . . . . . . . . . . 63,65 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 17 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . 269 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 222 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 317 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 19 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 150 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 DVD Player (Video Entertainment System) . . . . . . 214 Electric Remote Mirrors . .
INDEX Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 180 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . 303 Engine Oil Viscosity Chart . . . . . . . . . . . . . . . . . 303 Enhanced Accident Response Feature . . . . . . . . . . 56 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 16 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 57 Exhaust Gas Caution . . . . . . . . . . . . . . . . 70,271,313 Exhaust System . . . . . . . . . . . . . . . . .
INDEX Filler Door (Gas Cap) . . . . . . . . . . . . . . . . . . . 272 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 Requirements . . . . . . . . . . . . . . . . . . . . . . 268,341 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 341 Fuel System Caution . . . .
INDEX Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 277 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 HomeLink威 (Garage Door Opener) Transmitter . . . 150 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319,322 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 118 Interior Lights . . . . . . . . . . . . . . . . . . . . . . .
INDEX Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Liftgate Flipper Glass . . . . . . . . . . . . . . . . . . . . . . 27 Liftgate Window Wiper/Washer . . . . . . . . . . . . . 168 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71,118 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57,177 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Anti-Lock .
INDEX Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . 119,149 Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . . 339 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 181 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . 178 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Memory Seats and Radio . . . . . . . . . . . . . . . . . . 112 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 192 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 78 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 80 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . . 80 Exterior Folding . . . . . . . . .
INDEX Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Paint Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Park Assist System, Rear . . . . . . . . . . . . . . . . . . 138 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 144 Pets . . .
INDEX Rear Park Assist System . . . . . . . . . . . . . . . . . . . 138 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 109 Rear Window Features . . . . . . . . . . . . . . . . . . . . 168 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 168 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 106 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 57 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 285 Refrigerant . . . . . . . . . . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 71,328 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . . 37 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Easy Entry . . . . .
INDEX Emergency (Jump Starting) . . . . . . . . . . . . . . . 289 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 235 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 246,310 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Storage, Behind the Seat . . . . . . . . . . . . .
INDEX Radial . . . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . Sizes . . . . . . . . . . . . . . . . . . . . . . Spinning . . . . . . . . . . . . . . . . . . . Tread Wear Indicators . . . . . . . . . . Tongue Weight/Trailer Weight . . . . . Towing . . . . . . . . . . . . . . . . . . . . . . Behind a Motor Home . . . . . . . . . Guide . . . . . . . . . . . . . . . . . .
INDEX Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 196 Vehicle Identification Number (VIN) . . . . . . . . . . . . 7 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . . 253 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 8 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 229,334 Video Entertainment System (Rear Seat Video System) . . . . . . . . . . . . . . . . . .
INDEX
NOTES
NOTES
