SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 7 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeep威 Commander and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and handling will have a different feel from what drivers experience with other vehicles, so take time to become familiar with your vehicle.
INTRODUCTION Roll Over Warning Utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can be caused to go out of control.
INTRODUCTION Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually. In a roll over crash an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.
INTRODUCTION WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .14 䡵 Doors And Door Locks . . . . . . . . . . . . . . . . . . . .18 ▫ Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .20 䡵 Sentry Key Immobilizer System . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Battery Service . . . . . . . . . . . . . . .24 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .33 䡵 Security Alarm System — If Equipped . . . . . . . . .25 ▫ Lap/Shoulder Belt Operating Instructions . . . . .34 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .26 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .37 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 13 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Ignition Key Insert the key fully, then turn the switch to one of the four illustrated positions. The key can be inserted or withdrawn only in the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder If the driver’s door is opened when the key is in the ignition and not turned to the ON position, a chime will sound to remind you to remove the key. CAUTION! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. SENTRY KEY IMMOBILIZER SYSTEM The Sentry Key Immobilizer System (SKIM) prevents unauthorized operation of the vehicle by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the SKIM indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. will sound and the SKIM indicator light will begin to flash. Turn the ignition switch OFF and remove the second key. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undesired operation. ILLUMINATED ENTRY The interior lights come on when you open any door. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will fade to off if you turn on the ignition after you close all the doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Child Protection Locks The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Automatic Unlock on Exit Feature — Only Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in P (Park) or N (Neutral). Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 of this manual or see your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If desired, the system can be programmed to unlock all doors on the first press of the “Unlock” button. Refer to “Remote Unlock Driver’s Door 1st” in the Personal Settings section of the “Electronic Vehicle Information Center (EVIC)”, or simply follow these steps: 1. Press and hold the “Lock” button for 4 to 10 seconds. 2. While the “Lock” button is pressed, (after 4 seconds) press the “Unlock” button. Release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Using The Panic Alarm To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. While the “Unlock” button is pressed, (after 4 seconds) press the “Lock” button. Release both buttons. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3. To reassemble the transmitter case, join the two halves of the case together. Install and tighten the screw until snug. Make sure there is an even “gap” between the two halves. Test transmitter operation. SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set the Alarm The alarm will set when you use the remote keyless entry transmitter to lock the doors and liftgate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, a red light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the system is arming. During this 16 second pre-arm period, opening any door or the liftgate will cancel the arming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate. Liftgate Release 27 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. WARNING! To avoid injury stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 POWER WINDOWS The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. 2 Power Window Switches The power window switches remain active for up to 10 minutes after the ignition switch has been turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. 2 Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up: Pull the window switch up and close the window completely, then pull and hold the switch for 1 second.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle 35 WARNING! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! 37 Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert) If the driver or front passenger seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver or front passenger seat belt remains unfastened. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle also is equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. They are located above the side windows. Their covers are also labeled SRS/AIRBAG. 43 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioner • Occupant Classification System (OCS) — Front Passenger Seat Only − Occupant Classification Module − Passenger Airbag Disable (PAD) Indicator Light − Weight Sensors How The Airbag System Works • The Occupant Restraint Control (ORC) Module determines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Ignoring the “Airbag Warning Light” in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 adult passenger is properly seated in the front passenger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occurs. For almost all properly installed rear facing child restraints, the “PAD Indicator Light” will be illuminated indicating that the front passenger airbag is turned off and will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Seat Occupant Passenger Airbag Disable (PAD) Indicator Light OFF Airbag Status Adult ON Grocery Bags, Heavy Briefcases and Other RelaON OFF tively Light Objects Empty or Very OFF* OFF Small Objects * Since the system senses weight, some small objects will turn the PAD Indicator Light on. The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE because this can also affect occupant classification. Also, if you fold down the rear seat check to be sure it doesn’t touch the front passenger seat. If the front passenger seat is damaged in any way, it should only be serviced by an authorized dealer. If the seat is removed (or even if the seat attachment bolts are loosened or tightened in any way), take the vehicle to an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The driver front airbag gas is vented through the vent holes in the sides of the airbag. The passenger front airbag gas is vented through the vent holes in the sides of the airbag. In this way, the airbags do not interfere with your control of the vehicle. • The Occupant Classification Module (OCM) is located beneath the front passenger seat. The OCM classifies the occupant into categories based on the measurements made by the seat weight sensors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger seat assembly contains critical components that affect the front passenger airbag deployment. Correctly functioning front passenger seat components are critical for the Occupant Classification System (OCS) to properly classify the front passenger and calculate the proper airbag deployment. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper or vehicle body structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with other data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Seat belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary). For the second and third row seat belts with the automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extracted from the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction, are for children who weigh 20 to 40 lbs (9 to 18 kg), and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CH ildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The second row outboard seating positions have lower anchorages that are capable of accommodating LATCHcompatible child seats having flexible, webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 2 Latch Anchorages Tether Strap Mounting In addition, there are tether strap anchorages behind each rear outboard seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. WARNING! You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Lights Have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .78 3 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 ▫ Operations . . . . . . . . . . . . . . . . . . . . . . . . . . .84 ▫ Inside Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ Phone Call Features . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Front Seat Adjustment — Recline . . . . . . . . . . 106 ▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . . . 118 ▫ Manual Lumbar Support Adjustment . . . . . . . 106 䡵 To Open And Close The Hood . . . . . . . . . . . . . 119 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 107 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 ▫ 8 - Way Driver’s Power Seat . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 125 ▫ TCS (Traction Control System) . . . . . . . . . . . . 133 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 126 ▫ BAS (Brake Assist System) . . . . . . . . . . . . . . . 133 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ ERM (Electronic Rollover Mitigation) . . . . . . . 134 ▫ High Beam Switch . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . . . 148 ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 157 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 149 ▫ Reprogramming a Single Homelink Button . . . 158 ▫ To Set At a Desired Speed . . . . . . . . . . . . . . . 149 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 161 ▫ Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . 166 䡵 Command-View™ Skylights — If Equipped . . . . 161 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . . 168 䡵 Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . . 168 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Adjusting Rear View Mirror Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Inside Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated. 79 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Power Remote Control Outside Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors. Sun Visor Extension This feature has a pull out extension on the sun visor for increased coverage. Lift the cover to reveal the mirror. The light will turn on automatically. HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can either use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you. Voice Command Tree Refer to “Voice Tree” at the end of this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the voice on beep, say ⬙Pair a Phone.⬙ • You will be asked to say a four-digit pin number which you will later need to enter into your cellular.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙). 87 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. Dial by Saying a Number • The UConnect™ system will confirm the phone number and then dial.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect™ phonebook. Refer to ⬙Add Names to Your UConnect™ Phonebook,⬙ to learn how to store a name in the phonebook. • The UConnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE four associated phone numbers and designations. Each language has a separate 32 name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the ⬙Voice Recognition’ button during the playing of the desired name and say ⬙Call.⬙ NOTE: the user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls.⬙ To combine two calls, refer to ⬙Conference Call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination To end a call in progress, momentarily press the ⬘Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete language selection. • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Towing Assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word ⬙Send.⬙ For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’ button and say ⬙3 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnect™ System Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up Phone settings phone set up 105 SEATS WARNING! Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 button which must be pushed in to lower the head restraint to all positions. The restraints may be raised without pushing in the button. 3 Manual Lumbar Control Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8 - Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicate the level of heat in use. Two LEDs are illuminated for high, one for low, and none for off. Pressing the switch once will select high-level heating. 109 When high-temperature heating is selected, the heaters provide a boosted heat level during the first five minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull up on the seatback lever located on the outboard side of the seat. WARNING! NOTE: Also, pulling upward on this handle allows the outboard seating positions to be reclined. Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury. Seatback Release Lever 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 NOTE: If sitting in the third row seat, pull rearward on the release strap located at the rear of the seat and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Middle Seatback (Second Row Seat) 1. Pull the release strap. Folding Center Seatback Release Strap 2. Lower the center seatback. Center Seat Armrest (Second Row Seat) — If Equipped The second row center seat may be equipped with a armrest. Pull strap to lower armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 1. Open the tailgate. 2. Push the seatback release handle (toward rear of vehicle), and lower the seatback using the pull strap. 3 Armrest (Second Row Seat) 50/50 Third Row Folding Seat To Lower Rear Seat Either side of the third row seat can be lowered to allow for extended cargo space, and still maintain some rear seating room. Seatback Release Handle 3. Close the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Close the tailgate. To Raise Rear Seat 1. Open the tailgate. 2. Detach pull strap from back of seat, and pull seatback upward until it locks into place. Reattach strap. Pull Strap 3. Raise the head restraints. WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position. Driver Memory Switches Your vehicle may have been delivered with two Remote Keyless Entry transmitters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. Turn the ignition switch to the OFF position and remove the key. 7. Press and release the SET (S) button located on the driver’s door. 8. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door. The next step must be performed within 5 seconds if you desire to also use a Remote Keyless Entry transmitter to recall memory positions. 9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under ⬙Electronic Vehicle Information Center (EVIC) — Customer Programmable Features⬙ in Section 4 for more information. Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to ⬙Electronic Vehicle Information Center (EVIC) — Customer Programmable Features⬙ in Section 4 for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Courtesy/Reading Lights Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Multi-Function Control Lever Turn Signal Auto-Mode — If Equipped Tap the multi-function control lever once and the turn signal (left or right) will flash 3 times, and automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 This system performs two functions. With the engine running and the multi-function control lever in the A (Auto) position, the headlights will turn on and off based on the surrounding light levels. Headlights On Automatically With Wipers If your vehicle is equipped with Automatic Headlights it also has this customer programmable feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “Instrument Panel and Interior Lights” below for setting the instrument panel lights to full daytime intensity. SmartBeams — If Equipped The SmartBeam system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped The fog light switch is located in the multifunction control lever. To activate the fog lights, turn on the park/turn lights, low beam headlights, or “Auto” headlights and pull out the end of the multifunction control lever. A light in the instrument cluster shows when the fog lights are on. NOTE: Turning on the high beam headlights turns off the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60, or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multifunction control lever must be rotated to the “Off” position after the ignition switch is turned OFF. Only the headlights will illuminate during this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of five settings to activate this feature. 3 Rain Sensitive Wiper Switch The sensitivity of the system can be adjusted with the multi-function lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system. NOTE: • The rain sensing feature will not operate when the wiper switch is in the LOW or HIGH speed position. • The rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • Use of Rain-X威 or products containing wax or silicone may reduce rain sensor performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Tilt Steering Column 131 WARNING! Tilting the steering wheel column while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ABS (Anti-Lock Brake System) This system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in Section 5 of this manual for more information about ABS. (See page 271 for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TCS (Traction Control System) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Anytime the ESP system is in the “Full Off” mode, ERM is disabled. Refer to ESP (Electronic Stability Program) for a complete explanation of the available ESP modes. WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ⬙ESP/TCS Indicator Light⬙ located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ESP/TCS Indicator Light⬙ also flashes when TCS is active. If the ⬙ESP/TCS Indicator Light⬙ begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Range (4WD Models) or 2WD Models On This is the normal operating mode for ESP in 4WD high range and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD low range or neutral back to 4WD high range, the ESP system will be in this mode. This mode should be used for most all driving situations. ESP should only be turned to “Partial Off” or “Full Off” for specific reasons as noted below.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch. Once the situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily depressing the “ESP Control Switch”. This may be done while the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver, the ESP and ERM systems will not engage to assist in maintaining stability. The “Full Off” ESP mode is intended for off-highway or off-road use only. 4WD Low Range Partial Off This is the normal operating mode for ESP in 4WD low range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 186 for more information.) To turn ESP on again, momentarily depress the “ESP Control Switch”. This will restore the normal “Partial Off” mode of operation in 4wd low range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approximately 11.8 inches (30 cm) up to 59 inches (150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the obstacle is detected at a distance of about 59 inches (150 cm) from the rear fascia, the outermost LEDs of the warning display will be ON with increased brightness. Along with the LED, a half second tone will occur. As the distance of the detected obstacle to the rear fascia decreases, more LEDs are illuminated. When the warning display has the first 5 yellow LEDs ON, the warning display will actuate an intermittent tone for about 10 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enable/Disable the Rear Park Assist System The Rear Park Assist System can be enabled and disabled with a switch located in the switch bank of the instrument panel. When the switch is pressed to disable the system, the instrument cluster will display the ⬙PARK ASSIST DISABLED⬙ message. Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service the Rear Park Assist System When the Rear Park Assist System is defective, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the ⬙SERVICE PARK ASSIST SYSTEM⬙ message. Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Cleaning the Rear Park Assist System Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To Set at a Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory. Pressing the ON·OFF to turn the system OFF or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting When the Speed Control is ON, speed can be increased by pressing and holding the RES·ACCEL button. When the button is released, a new set speed will be established. Tapping the RES·ACCEL button once will result in a 2 mph (3 km/h) (3.7L/4.7L Models) or a 1 mph (2 km/h) (5.7L Models) speed increase. Each time the button is tapped, speed increases, so tapping the button three times will increase speed by 6 mph (10 km/h) (3.7L/4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains an optional universal garage door opener (HomeLink威), storage for sunglasses, and optional power sunroof switches. GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. The Electronic Vehicle Information Center (EVIC) features a driver-interactive display which includes HomeLink system messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The EVIC display will show “CHANNEL X TRAINING” (where X is Channel 1, 2, or 3). Release both buttons after the EVIC display shows “CHANNEL X TRAINED.” NOTE: If the EVIC display shows “DID NOT TRAIN” repeat steps 2–4. HomeLink Buttons 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. 7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter signals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press and hold the two outer HomeLink buttons and release only when the EVIC display shows “CHANNELS CLEARED” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - Step 2. Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console. Power Sunroof Switch 159 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Hold onto shade handle until shade is completely open or closed. POWER OUTLET To the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear power outlet (if equipped) is located in the left rear cargo area. 163 The power outlets are a direct feed from the battery so they receive power whether the ignition is in the ON or OFF position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: The cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console surface. Cup Holders (Second Row Seat) The second row seat has two cup holders in the center armrest. Lower the center armrest. Refer to “Seats” in this section. Press the front of the cup holder, and the cup holder will come out of the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cup Holders (Third Row Seat) The third row seat passengers have cup holders on the left and right rear trim panels. CARGO AREA FEATURES Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray. 3 Rear Storage Cover NOTE: The cargo load floor latches should not be used as cargo tie-downs. 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. Cargo Load Floor 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Push loop(s) back down, so they are parallel to the top of the tray. REAR WINDOW FEATURES Rear Window Wiper/Washer A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the wiper. Rotating the center of the switch all the way up or down will turn on the wash function.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper. Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the rear cross rail (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception. For improved satellite radio reception, place the rear cross rail in detent position #4 when not in use. CAUTION! • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without cross rails installed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Interior Controls . . . . . . . 176 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 199 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 177 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 200 䡵 Instrument Cluster Description . . . . . . . . . . . . . 178 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 200 䡵 Electronic Vehicle Information Center — If Equipped . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions (CD Mode For CD Audio Play) . . . . . . . . . . . 206 ▫ Operating Instructions - Hands Free Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 222 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . 208 ▫ Operating Instructions - Satellite Radio — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 222 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 175 ▫ Selecting Satellite Mode In REF Radios . . . . . . 227 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 231 ▫ Selecting Satellite Mode In RAQ Radios . . . . . 227 䡵 Radio Operation And Cellular Phones . . . . . . . . 232 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 228 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 232 ▫ Storing And Selecting Pre-Set Channels . . . . . . 228 ▫ Climate Controls — Manual . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND INTERIOR CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 177 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light The BRAKE warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light stays on longer, it may be an indication that the parking brake has not been released.
UNDERSTANDING YOUR INSTRUMENT PANEL engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 8. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL prevailing road conditions. The “ESP/TCS Indicator Light” will flash any time the ESP or TCS is active and helping to improve vehicle stability. If the “ESP/TCS Indicator Light” is on solid, the ESP system has been turned off by the driver or a temporary condition exists that will not allow full ESP function. (See page 131 for more information.) 12.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Vehicle Information Center Display When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to “Electronic Vehicle Information Center” later in this section. (See page 186 for more information.) 183 BAS warning light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system.
UNDERSTANDING YOUR INSTRUMENT PANEL or remain on continuously. Refer to ⬙Enhanced Driver Seat Belt Reminder System (BeltAlert)⬙ in the Occupant Restraints section for more information. 21. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 19. Cruise Indicator Light This indicator lights when the speed control system is turned ON. 22. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 20.
UNDERSTANDING YOUR INSTRUMENT PANEL when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. 24. Front Fog Light Indicator Light— If Equipped This light shows the front fog lights are ON. 25.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER — IF EQUIPPED • TURN SIGNAL ON • PERFORM SERVICE • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PROGRAM LIMIT • PROGRAMMING ACTIVE — NEW KEY PROGRAMMED • SERVICE SECURITY KEY • INVALID KEY — TRY ALTERNATE KEY The electronic vehicle information center (EVIC) located in the instrument cluster, when the appropriate conditions exist, will display the following messages and
UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/DOOR OPEN (with graphic) • LIFTGLASS/HOOD OPEN (with graphic) • LIFTGATE/DOORS OPEN (with graphic) • WASHER FLUID LOW (with graphic) • LIFTGLASS OPEN (with graphic) • CHECK GAUGES • HOOD OPEN (with graphic) • AUTO HIGHBEAM ON • HOOD/DOOR OPEN (with graphic) • AUTO HIGHBEAM OFF • HOOD/DOORS OPEN (with graphic) • PARK ASSIST DISABLED • LIFTGATE/HOOD OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • HOOD/GLASS/DOOR OPEN (with graphic) • TRANSMISSI
UNDERSTANDING YOUR INSTRUMENT PANEL • CHECK GAS CAP • ESP OFF • MEMORY #1 POSITIONS SET • MEMORY #2 POSITIONS SET • MEMORY SYSTEM DISABLED — SEATBELT FASTENED (with graphic) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • DRIVER 1 MEMORY • PEDAL ADJUST DISABLED — SHIFTER IN REVERSE • SERVICE TIRE PRESS SYSTEM • LEFT FRONT LOW PRESSURE (Premium TPM System Only) • RIGHT FRONT LOW PRESSURE (Premium TPM System Only) • LEFT REAR LOW PRESSURE (Premium TPM System Only) • DRIVER 2 MEMORY • RIGHT REAR LOW
UNDERSTANDING YOUR INSTRUMENT PANEL Customer Programmable Features Press the MENU button until one of the display choices following appears: 189 Language? When in this display you may select one of three languages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display selects English, Espanol, or Francais. As you continue the displayed information will be shown in the selected language.
UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL memory set position using the door mounted switch. Pressing the STEP button when in this display will select “Yes” or “No.” Sound Horn With Lock? When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL this display will select “Low Beam” or “Low/High Beam.” Refer to “Lights — SmartBeams” in Section 3 of this manual. NOTE: System will activate at or above 20 mph (32 km/h). Headlamps On With Wipers? (Available with Auto Headlights Only) When this feature is selected and the headlight switch has at least once been moved to the A (Auto) position, the headlights will turn on when the wipers are turned on.
UNDERSTANDING YOUR INSTRUMENT PANEL Easy Entry/Exit Seat? (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. The Easy Entry/ Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/ Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
UNDERSTANDING YOUR INSTRUMENT PANEL Reset Button Press the RESET button to reset the display you are in. Press and hold the RESET button (for 2 seconds) to reset all of the displays. Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the accumulated ignition ON time since the last reset. Tire Pressure Display — If Equipped Shows the current pressure of all 4 road tires. 197 NOTE: Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures” in Section 5 for additional information. Miles to Service Shows the distance remaining to require service.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass. Refer to Variance Map. To Put Into a Calibration Mode Start the engine and leave the transmission in the P (Park) position. Set the display to “Compass/Temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the C/T button for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the STEP button for 1 second to select the new variance zone and press the RESET button to resume normal operation. RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 2. Adjust the hours by turning the right side Tune / Audio control. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. 3. After the hours are adjusted, press the right side Tune / Audio control to set the minutes. The minutes will begin to blink. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fifth time and FADE will display. Turn the TUNE control to the left or right to adjust the sound level between the front and rear speakers. Press the rotary TUNE control again to exit setting tone, balance and fade. RND/PTY Button (Radio Mode) Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Nostalgia Oldies Personality Public Rhythm_and_Blues Religious_Music Religious_Talk Rock Soft Soft_Rock Soft_R_&_B Sports Talk Top_40 Weather 205 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET/DIR button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM,12 FM and 12 Satellite (if equipped) stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT Button (CD Mode for CD Audio Play) Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 2. Adjust the hours by turning the right side Tune/ Audio control. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. The minutes will begin to blink. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will be displayed. Turn the TUNE control to the right or left to increase or decrease the Bass tones. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fifth time and FADE will be displayed. Turn the TUNE control to the left or right to adjust the sound level between the front and rear speakers. Press the tune control again or wait 5 seconds to exit setting tone, balance, and fade. RND/SET Button (Radio Mode) To SET The Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play. The display will show the track number and play time in minutes and seconds. Play will begin at the start of track one.
UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear. TIME Button (CD Mode) Press this button to change the display from elapsed CD playing time to time of day. The time of day will be displayed for 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will be displayed for 5 seconds. Operating Instructions - Satellite Radio — If Equipped Refer to the Satellite Radio section of the Owner’s Manual. RW/FF (Auxiliary Mode) No function. SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM RND/SET Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit.
UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The DVD player is mounted in the rear of the center console storage bin, and is concealed by a door that lifts up for access. Refer to your VES™ User’s Manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 The LCD screen is located on the headliner behind the front seats.
UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers over 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 first four digits are displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RAQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
UNDERSTANDING YOUR INSTRUMENT PANEL Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Pressing the ⬙SEEK⬙ or ⬙SCAN⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button ⴖSEEKⴖ When the desired program is obtained, press the ⬙SEEK⬙ button within five seconds. The channel will change to the next channel that matches the program type selected.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.).
UNDERSTANDING YOUR INSTRUMENT PANEL 231 The button located in the center of the left hand control will tune to the next preset station that you have programmed in the radio preset push-button. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: CD Player Pressing the top of the switch once will go to the next track on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Press this button to turn on and off the air conditioning. Cool dehumidified air comes through the outlets selected by the mode selector. Press the button a second time to turn off the air conditioning. The button includes an LED that illuminates when compressor operation is selected. Electric Rear Window Defroster Press this button to turn on the rear window defroster and the heated side mirrors (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The temperature of air can be selected by rotating the center temperature control knob. The coldest temperature setting is on the extreme left and the warmest setting on the extreme right of the rotation. The knob can be positioned at any point on the dial. Mode Selection The mode selector (the right rotary knob) can be placed in several positions.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to partially block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. Panel Air flows through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control — If Equipped The Infrared Dual-Zone Climate Control System automatically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face of the control unit.
UNDERSTANDING YOUR INSTRUMENT PANEL LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once the comfort level is selected the system will maintain that level automatically using the heating system.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off until the engine warms up.
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions. When the Mode is set to any position other than AUTO, The automatic control of air temperature is disabled.
UNDERSTANDING YOUR INSTRUMENT PANEL Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • Panel Air flows through the outlets located in the instrument panel. Air flows through the registers in the back of the center console to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The recirculation mode should only be used temporarily. The button includes an LED that illuminates, which indicates that the recirculation mode is active. You may use this feature separately. NOTE: Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the “Recirculate” icon button to return to outside air.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Mode Control If rear heating/cooling is desired, press the “Rear On/Off Switch” (located in the upper switch bank above the controls) and select “Floor” “Bi-Level” or “Panel” from the Rear Control Panel (right knob located on the right rear quarter trim panel). Rear Control Panel • Floor Air flows through the floor outlet located on the right side of the rear floor into the rear seating area.
UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Air flows through both the outlets located in the rear quarter trim panels, and the one located on the floor. The rear quarter trim panel outlets can be closed to block airflow. • Panel Air flows through the outlets located in the rear quarter trim panels. These registers can be closed to block airflow. Rear Blower Control The left knob on the Rear Control Panel has four positions, “Off”, and a range of three blower speeds.
UNDERSTANDING YOUR INSTRUMENT PANEL • When the temperature knob is in the cold (Blue) position, cold air will be delivered from the outlets. As the temperature knob is turned towards the hot (Red) position, the air will get warmer. Winter Operation Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost, and turning on the high blower. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 253 ▫ Rocking The Vehicle . . . . . . . . . . . . . . . . . . . 263 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 253 䡵 Four-Wheel Drive Operation . . . . . . . . . . . . . . . 264 ▫ Extreme Cold Weather (Below –20°F (–29°C) . . 254 ▫ Quadra-Trac I威 Operating Instructions/Precautions — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 264 ▫ If Engine Fails To Start . . . . . . . . .
STARTING AND OPERATING 䡵 Anti-Lock Brake System . . . . . . . . . . . . . . . . . . 271 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 281 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 274 ▫ Tire Identification Number (TIN) . . . . . . . . . . 284 䡵 On-Road Driving Tips . . . . . . . . . . . . . . . . . . . 275 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 285 䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 251 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . . 297 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 307 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . . 297 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 308 ▫ Premium System . . . . . . . . . . . . . . . . . . . . . . 299 䡵 Fuel Tank Filler Cap (Gas Cap) . . . . . . . . . . . . . 309 ▫ General Information . . . . . . . . . . . . . . . . . . . 303 ▫ Loose Fuel Filler Cap Message . .
STARTING AND OPERATING ▫ Towing – 2WD Models . . . . . . . . . . . . . . . . . 323 ▫ Towing — Quadra-Trac I (Single-Speed Transfer Case) 4WD Models . . . . 323 ▫ Towing — Quadra–Trac II /Quadra–Drive II 4WD Models . . . . . . . . . . . . . . . . . . . . . . . . 324 䡵 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. 253 Normal Starting Normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme Cold Weather (below –20°F (–29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended.
STARTING AND OPERATING After Starting The idle speed will automatically decrease as the engine warms up. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather.
STARTING AND OPERATING TRANSMISSION SHIFTING 5–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should apply the park brake, shift the transmission into P (Park), and remove the key from the ignition. Once the key is removed from the ignition the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING shifter is in the D (Drive) position, allowing the selection of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid.
STARTING AND OPERATING NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, the transmission will shift to 3rd gear and 4th will be enabled under steady cruise conditions. 261 activated. Pressing the switch a second time restores normal operation. If the “TOW/HAUL” mode is desired, the switch must be pressed each time the engine is started. Transmission Limp Home Mode Transmission function is monitored for abnormal conditions.
STARTING AND OPERATING 4. Wait approximately 10 seconds, then restart the engine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, P (Park), R (Reverse), and N (Neutral) will continue to operate. Only Second gear range will operate in the D (Drive) shifter position. Have the transmission checked at your authorized dealer as soon as possible.
STARTING AND OPERATING cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. Rocking the Vehicle If the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between D (Drive) and R (Reverse), while applying slight pressure to the accelerator.
STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION Quadra-Trac I姞 Operating Instructions/Precautions — If Equipped The Quadra-Trac I威 is a single speed (HI range only) transfer case which provides convenient full-time 4–wheel drive. No driver interaction is required. This transfer case divides engine torque almost evenly with 48 percent of engine torque to the front axle and 52 percent of engine torque to the rear axle.
STARTING AND OPERATING road surfaces only. Driving in the 4 LOW position on dry hard surfaced roads may cause increased tire wear and damage to driveline components. When operating your vehicle in 4 LOW, the engine speed is approximately three times that of the 4 HI position at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.
STARTING AND OPERATING N (Neutral) Neutral — Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in Section 5 of this manual. 4 LOW Four Wheel Drive Low Range — Low speed 4 wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only.
STARTING AND OPERATING 267 LOW Indicator Lamp” in the instrument cluster will flash and go out when the shift is complete. Release the T-handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 186 for more information.
STARTING AND OPERATING Neutral (N) Shift Procedure 1. Key ON, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission in N (Neutral). 4. Hold down N (Neutral) “pin” switch (with a pen, etc.) for 4 seconds until the LED lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (stay on solid) when Neutral shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic Vehicle Information Center).
STARTING AND OPERATING NOTE: If shift conditions/interlocks are not met, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 186 for more information.) Quadra-Drive II姞 System — If Equipped The optional Quadra-Drive II威 System features three torque transfer couplings.
STARTING AND OPERATING NOTE: The instrument cluster “Brake Warning Light” indicates only that the parking brake is applied. It does not indicate the degree of brake application. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the P (Park) position. Make certain the transfer case is in gear. Failure to do so may cause the vehicle to roll and cause damage or injury.
STARTING AND OPERATING WARNING! • Leaving children unattended in a vehicle is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING WARNING! WARNING! Significant over or under inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. The Anti-Lock Brake System conducts a low-speed selftest at about 12 mph (20 km/h).
STARTING AND OPERATING 273 WARNING! CAUTION! • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
STARTING AND OPERATING • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission or locking out overdrive whenever possible.
STARTING AND OPERATING NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and does not indicate that there is a problem with the power steering system. Upon initial start-up in cold weather, the power steering pump may make noise for a short period of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and does not in any way damage the steering system.
STARTING AND OPERATING conventional 2-wheel drive vehicles any more than lowslung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover.
STARTING AND OPERATING caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing Water If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches. The flowing water can erode the streambed causing your vehicle to sink into deeper water.
STARTING AND OPERATING Hill Climbing NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4WD LOW. Use first gear and 4WD LOW for very steep hills. If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine and shift to R (Reverse).
STARTING AND OPERATING Traction Downhill Shift the transmission into a low gear and the transfer case to 4WD LOW range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 281 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 283 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 285 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 289 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper cold tire inflation pressure is listed on either the face of the driver’s door, or the driver’s side “B” pillar. 3.
STARTING AND OPERATING 291 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your dealer for radial tire repairs.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE PRESSURE MONITOR SYSTEM (TPMS) Base System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
STARTING AND OPERATING NOTE: For vehicles with optional wheel/tire sizes and significantly different tire placard pressures, the placard pressure value and the low-pressure threshold value is re-programmable at your authorized dealer to accommodate the customer selected wheel/tire combinations recommended by DaimlerChrysler Corporation. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. NOTE: • The TPMS can inform the driver of a low tire pressure condition. • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition.
STARTING AND OPERATING when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset.
STARTING AND OPERATING Telltale Light” will illuminate continuously (solid) and shall remain illuminated until the warning condition is removed/reset. NOTE: The “Tire Pressure Monitoring Telltale Light” will only illuminate for the four active road tires. A low spare tire pressure will not cause the “Tire Pressure Monitoring Telltale Light” to illuminate When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
STARTING AND OPERATING CAUTION! CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage.
STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. 303 TIRE CHAINS Certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
STARTING AND OPERATING FUEL REQUIREMENTS 3.7/4.7L Engines (If Equipped) All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended. Under normal conditions, the use of premium gasoline will not provide a benefit over high quality regular gasolines, and in some circumstances may result in poorer performance.
STARTING AND OPERATING Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasoline that meets the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as Reformulated Gasoline.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. 309 FUEL TANK FILLER CAP (GAS CAP) The fuel cap is located on the left side of the vehicle. If the fuel cap is lost or damaged, make sure the replacement cap is the correct one for this vehicle.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. • Turn the engine off. • Rotate the fuel cap to the left to remove.
STARTING AND OPERATING Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “CHECK GAS CAP” message will be displayed in the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center” in Section 4 of this manual. (See page 186 for more information.) Tighten the fuel filler cap properly and press the odometer reset button to turn the message off.
STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible.
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers. Weight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame.
STARTING AND OPERATING 315 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Model GVWR (Gross Ve- GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmission hicle Wt. Rating) bined Wt. Rating) Trailer Wt.) (See Note 1) 3.7L/ 4x2 6,200 lbs (2 812 kg) 8,670 lbs (3 933 kg) 40 Sq. Ft (3.72 3,500 lbs (1 587 kg) 350 lbs (159 kg) Automatic square meters) 3.
STARTING AND OPERATING Note 1 – The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to the Tire– Safety Information Section in this manual. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING 321 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 5 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transmission fluid change intervals. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”Tow/ Haul” mode (if equipped) or the “3” range should be selected.
STARTING AND OPERATING − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning Turn off temporarily. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. 323 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing – 2WD Models Recreational towing is allowed ONLY if the driveshaft is removed.
STARTING AND OPERATING Towing — Quadra–Trac II /Quadra–Drive II 4WD Models CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: The transfer case must be in the N (Neutral) position, and the transmission must be in the P (Park) position for recreational towing. Shifting Into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing.
STARTING AND OPERATING “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 186 for more information.) 325 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into P (Park). 10. Place the ignition key in the OFF position, and remove key. 11. Apply parking brake. 12. Attach vehicle to the tow vehicle with tow bar. 13. Release parking brake. Neutral Switch 5. Start engine. 6. Shift transmission into D (Drive).
STARTING AND OPERATING CAUTION! Transmission damage may occur if the transmission is shifted into P (Park) with the transfer case in N (Neutral) and the engine running. With the transfer case in N (Neutral) ensure that the engine is OFF prior to shifting the transmission into P (Park) (refer to steps 7 – 8 above). Shifting Out Of Neutral (N) Use the following procedure to prepare your vehicle for normal usage. 1. Depress brake pedal. 2. Turn the ignition key ON, engine off. 3.
STARTING AND OPERATING 327 NOTE: When shifting out of transfer case N (Neutral), turning the engine OFF may be required to avoid gear clash. WARNING! Neutral Switch 5. Shift transmission into P (Park). 6. Start the engine. 7. Shift transmission into D (Drive). You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
STARTING AND OPERATING CAUTION! WARNING! Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured. SNOW PLOW Snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . . 330 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 335 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 331 䡵 Jump Starting Procedure . . . . . . . . . . . . . . . . . . 338 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 332 䡵 Emergency Tow Hooks — If Equipped . . . . . . . . 340 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not to be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes.
WHAT TO DO IN EMERGENCIES 333 Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the liftgate opening. WARNING! Do not use power tools to winch the tire up or down. Impact type tools can damage the winch mechanism.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Fit the jack handle extension over the drive nut. Use the Lug Wrench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in P (Park). Turn OFF the ignition.
WHAT TO DO IN EMERGENCIES For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. 335 3. Assemble the jack and jacking tools as shown. Connect jack handle driver (A) to two extensions (B), then to the lug wrench (C). Jacking Instructions 1. Remove the spare tire, jack, and tools from storage. 2.
WHAT TO DO IN EMERGENCIES 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise.
WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered.
WHAT TO DO IN EMERGENCIES NOTE: Tire should be stowed with the “beauty” side up. Storing the tire upside down may result in scratching or damage to the wheel face. Continue winching up the tire until you hear the winch “ratchet” three times. Double check to ensure the tire is snug against the underbody of the vehicle. Damage to the winch cable may result if the vehicle is driven with the tire loose. WARNING! Do not use power tools to winch the tire up or down.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then connect the other end to a non-paint metal surface on the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7.
WHAT TO DO IN EMERGENCIES • Be sure your vehicle is not touching the jump start vehicle. • Observe all Battery Warnings in Section 7 of this manual, while jump starting your vehicle. WARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. TOWING A DISABLED VEHICLE 2WD Models Only Provided the transmission is operable, tow only in N (Neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km) can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . . 351 䡵 4.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 352 䡵 5.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 360 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 361 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 363 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 363 ▫ Windshield Washers — Front And Rear . . . . . 363 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 364 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 365 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . .
MAINTAINING YOUR VEHICLE 345 3.
MAINTAINING YOUR VEHICLE 4.
MAINTAINING YOUR VEHICLE 347 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Trailer towing • Taxi, Police, or delivery service (Commercial Service) • Off road or desert operation 353 Engine Oil Selection For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar威 or an equivalent oil meeting the specification MS-6395. Engine Oil Viscosity (5.7L Engines) SAE 5W-20 engine oil is recommended for all operating temperatures.
MAINTAINING YOUR VEHICLE Materials Added to Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of the used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the converter as an emission control device.
MAINTAINING YOUR VEHICLE 357 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing. • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE 359 WARNING! WARNING! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery.
MAINTAINING YOUR VEHICLE To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information Book for additional warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not use Automatic Transmission Fluid (ATF) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid.
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and operate the system for a few seconds to flush out the residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you.
MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Engine Coolant Checks Check antifreeze/coolant protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush, And Refill At the intervals shown in the appropriate “Maintenance Schedule,” the system should be drained, flushed, and refilled. If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze/coolant solution.
MAINTAINING YOUR VEHICLE Adding Engine Coolant Your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same antifreeze/coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) antifreeze/coolant.
MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! The warning words DO NOT OPEN HOT on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
MAINTAINING YOUR VEHICLE When additional antifreeze/coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Hoses and Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold.
MAINTAINING YOUR VEHICLE fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking.
MAINTAINING YOUR VEHICLE 373 for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly. CAUTION! Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving.
MAINTAINING YOUR VEHICLE 5. Remove the dipstick, wipe it clean and reinsert it until seated. (upper) reference holes when the transmission reaches 180°F (82°C). Remember it is best to check the level at the normal operating temperature. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature.
MAINTAINING YOUR VEHICLE Special Additives The manufacturer recommends against the addition of any additives to the transmission. Exception to this policy is the use of special dyes to aid in detecting fluid leaks. Transfer Case Fluid Level Check Inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be checked by removing the filler plug located on the back side of the transfer case.
MAINTAINING YOUR VEHICLE Front/Rear Axle Fluid Front Axle Fluid Level Check Lubricant should be to the bottom of the oil fill hole. Rear Axle Fluid Level Check Lubricant should be 1/2” (1 cm) below the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE CAUTION! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body components, all driveline joints and steering linkage more often than in normal service to prevent excessive wear. Appearance Care And Protection From Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar威 Super Kleen Bug and Tar Remover to remove. • Use Mopar威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 379 • Aluminum wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopar威 cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.
MAINTAINING YOUR VEHICLE do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. 381 FUSE PANEL Interior Fuses The fuse panel is on the lower instrument panel just to the left of the steering column. If the belts need cleaning, use Mopar威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them.
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 9 10 11 12 Fuse/Color 30 Amp Pink 15 Amp Blue 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 10 Amp Red Spare 10 Amp Red Description Audio Amp (B+) Sunroof (B+) Htd Mirror (EBL) Rr Pwr Out (B+) Rr HVAC (R/O) OCM (B+) Door Locks (B+) Steer Col Lock (B+) Pwr Outlet (B+) Ign Run Only Out (R/O) 13 14 15 Spare 20 Amp Yellow Cigar Ltr (R/A) 10 Amp Red Tire Press Mon (R/O) Mem.
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Power Distribution Center Cavity 1 2 3 Fuse/Color 40 Amp Green 30 Amp Pink 30 Amp Pink Description HVAC Blower Power Outlets Rr Wiper/Ign R/O Cavity 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Fuse/Color 30 Amp Pink 50 Amp Red 50 Amp Red 30 Amp Pink 40 Amp Green Spare 40 Amp Green 30 Amp Pink 40 Amp Green 40 Amp Green 50 Amp Red 50 Amp Red 25 Amp Natural Spare 20 Amp Yellow 20 Amp Yellow 383 Description ABS Pump Cabin Htr 1 (Diesel
MAINTAINING YOUR VEHICLE Cavity 20 21 22 23 24 25 26 27 28 29 30 31 Fuse/Color 20 Amp Yellow 30 Amp Pink Spare 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 15 Amp Blue 25 Amp Natural Spare Spare Mini Relay 32 33 34 Micro Relay Micro Relay Micro Relay Description PCM Batt (Gasoline Only) ABS Valves Cavity Fuse/Color 35 Micro Relay 36 Mini Relay FDCM Fuel Pump FDCM/E-Diff.
MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Integrated Power Module Cavity 1 2 3 Fuse/Color Micro Relay Micro Relay Micro Relay Description Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly Cavity 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Fuse/Color Micro Relay Micro Relay Micro Relay Micro Relay 10 Amp Red 10 Amp Red 10 Amp Red Mini Relay 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Rear Fog Rly (BUX Only)
MAINTAINING YOUR VEHICLE Cavity 20 21 22 23 24 25 26 27 28 29 30 Fuse/Color 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 50 Amp Red Mini Relay Micro Relay Micro Relay 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Description FCM Batt #3 Rt T-Tow Stop/Turn FDCM Mod Rad Fan Rad Fan Lo Rly Ft Fog Lamps Rly Adjustable Pedal Rly IOD #1 IOD #2 (Audio) ORC (Ign R/.S) ORC (Ign R/O) VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Interior Lights Bulb Type Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Grab Handle Light . . . . . . . . . . . . . . . . L002825W5W Overhead Console Reading Lights . . . . . . . . . . VT4976 Rear Cargo Light . . . . . . . . . . . . . . . . . . . . . . . 214–2 Visor Vanity Light . . . . . . . . . . . . . . . . . . . . . V26377 Underpanel Courtesy Lights . . . . . . . . . . . . . . . . . 906 Instrument Cluster (General Illumination) . . . .
MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (5W-30, API Certified) 4.7 Liter Engine (5W-30, API Certified) 5.7 Liter Engine (5W-20, API Certified) Cooling System * 3.7 Liter Engine (Mopar威 Engine Coolant/Antifreeze 5 Year/ 100,000 Mile Formula) 4.7 Liter Engine (Mopar威 Engine Coolant/Antifreeze 5 Year/ 100,000 Mile Formula) 5.
MAINTAINING YOUR VEHICLE 389 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (3.7L/4.7L Engines) Engine Oil (5.7L Engines) Oil Filter (All Engines) Spark Plugs Fuel Selection (3.7L and 4.7L Engines) Fuel Selection (5.7L Engines) Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case (3.7L Engines) Transfer Case (4.7L/5.7L Engines) Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid Mopar威 ATF+4 Automatic Transmission Fluid Mopar威 NV 247 Transfer Case Lubricant Mopar威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 392 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 395 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 392 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 392 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service) • Off-road or desert driving • If equipped for and operated with E-85 (ethanol) fuel. NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” NOTE: If ANY of these apply to you, change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance recommendations in “Maintenance Schedule B.
M A I N T E N A N C E S C H E D U L E S 8 394 MAINTENANCE SCHEDULES • Check the windshield washer solvent, add as required. At Each Oil Change Once a Month • Change the engine oil filter. • Check the tire pressure and look for unusual wear or damage. • Inspect the exhaust system. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
M 396 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Drain and refill the front and rear axles. Inspect the brake linings. Drain the transfer case and refill.
M 398 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axles. Drain and refill the automatic transmission fluid, and replace main sump filter (4.
M 400 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axle fluid.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Drain and refill the transfer case fluid. Inspect the brake linings. Drain and refill the front and rear axle fluid.
M 402 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Flush and replace the engine coolant/anti-freeze, if not done at 60 months.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid.
M 404 SCHEDULE “B” A I 108,000 111,000 114,000 117,000 120,000 N Miles T (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) E X N Flush and replace the engine coolant/anti-freeze at A 120 months, if not replaced at 102,000 miles (170 N 000 km). C E Inspection and service should also be performed anytime * This maintenance is not required if the belt was S C H E D U L E S 8 a malfunction is observed or suspected. Retain all receipts.
SCHEDULE “A” 405 M Schedule “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Replace the spark plugs. Inspect the brake linings. Drain the transfer case and refill.
M 406 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Inspect the brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary. Flush and replace the engine coolant/anti-freeze at 60 months, if not replaced at 102,000 miles (170 000 km). Inspect the brake linings.
M 408 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not replaced at 60 months.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not done at 102,000 miles (170 000 km). Drain the transfer case and refill.
M 410 SCHEDULE “A” A I * This maintenance is not required if the belt was N T previously replaced. E N WARNING! A N C You can be badly injured working on or around a E S C H E D U L E S 8 motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ Prepare For The Appointment . . . . . . . . . . . . 412 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 412 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 415 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 415 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 179,271 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 169 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 147 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 358 Air Conditioner Maintenance . . . . . . . . . . . . . . . 360 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 232 Air Conditioning, Operating Tips . . . . . . . . . . . . 236 Air Conditioning, Rear Zone . . . . . . . . . . . . . .
INDEX Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 Auxiliary Electrical Outlet (Power Outlet) . . . . . . 162 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 162 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 338 Keyless Transmitter Replacement (RKE) . . . . . . . 24 Saving Feature (Protection) . . . . . . . . . . . . . . . 122 Belts, Drive . . . . . . . . . . . . . . . . . . . .
INDEX Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 332 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 282 Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . 70,71 Child Restraint . . . . . . . . . . . . . . . . . . . . 58,59,64,66 Child Restraint Tether Anchors . . . . . . . . . . . . . 63,64 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 19 Climate Control .
INDEX Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 233 Defroster, Windshield . . . . . . . . . . . . . . . . 71,234,241 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 348 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 126 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . 373 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 352 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 361 Disabled Vehicle Towing . . . . . . . . .
INDEX Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 255 Break-In Recommendations . . . . . . . . . . . . . . . . 68 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . 346 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 69,308 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . 254 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . 254 Fuel Requirements . . . . . . . . . .
INDEX Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . 372,373 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 361 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 389 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 126,185 Fold and Tumble Rear Seat . . . . . . . . . . . . . . . . . 109 Folding Rear Seat .
INDEX Gear Ranges . . . . . . . . . . . General Information . . . . . . Glass Cleaning . . . . . . . . . . Gross Axle Weight Rating . . Gross Vehicle Weight Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 24,303 . . 380 . . 313 . . 312 Hands-Free Phone (UConnect™) . . . . . . . . . . . . . . 82 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 330 Head Restraints . . .
INDEX Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 120 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 120,125 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 128 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . 332,335 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . 335 Jump Starting . . . .
INDEX Dimmer Switch, Headlight . . . . . . . . . . . . . 122,126 Electronic Stability Program (ESP) Indicator . . . . . . . . . . . . . . . . . . . . . . . . 140,180,183 Electronic Throttle Control Warning . . . . . . . . . 184 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126,185 Four-Wheel Drive Indicator . . . . . . . . . . . . . . . 183 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 Hazard Warning Flasher . . . . . . . . . . . . . . . . .
INDEX Liftgate, Tailgate . . . . . . . . . . . . . . . . . . . . . . . . 18 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63,64 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 363 Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . 169 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 106 Maintenance Free Battery . . . . . . . . . . . . .
INDEX Occupant Classification System (OCS) . . . . . . . . . . 48 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 32 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 305 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 183,184 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Off-Pavement Driving (Off-Road) . . . . . . . . . . 276,376 Off-Road Driving (Off-Pavement) . . . . . . . . . . 276,376 Oil, Engine . . . . . . . . . . . . . . . . .
INDEX Polishing and Waxing . . . . . . . . . . . . . . . . . . . . . 378 Power Distribution Center . . . . . . . . . . . . . . . . . . . . . 383 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 162 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 274,361 Sunroof . . . . . . . . .
INDEX Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 56 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 323 Shifting into Transfer Case Neutral (N) . . . . . . . 324 Shifting out of Transfer Case Neutral (N) . . . . . 326 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 306 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Reminder, Lights On . . . . . . . . . . . . . . . . . . . . . 125 Reminder, Seat Belt . . . . . . . . . . . . .
INDEX Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . . 37 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Fold and Tumble Rear . . . . . . . . . . . . . . . . . . . 109 Head Restraints . . . . . . .
INDEX Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Speed Control (Cruise Control) . . . . . . . . . . . . . . 148 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Automatic Transmission . . . . . . . . . . . . . . . . . 253 Cold Weather . . . . . . . . . . . . . . . . . . . . . . 254,255 Emergency (Jump Starting) . . . . . . . . . . . . . . . 338 Engine Block Heater . . . . . . .
INDEX Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 290 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Load Capacity . . . . . . . . . . . . . . . . . . . . . 285,286 Pressure Monitor System (TPMS) . . . . . . . . . . . 297 Pressure Warning Light . . . . . . . . . . . . . . . . . . 181 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 417 Radial . . . . . . . . . . . . . . . . . . . . .
INDEX Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . 256,372 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 372 Range Indicator . . . . . . . . . . . . . . . . . . . . . . . 184 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Transmitter Battery Service (Remote Keyless Entry) . 24 Transmitter, Garage Door Opener (HomeLink威) . . 152 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 21 Tread Wear Indicators . . . . . . . . . . . . . .
INDEX 437 Windows Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Windshield Defroster . . . . . . . . . . . . . . . . 71,234,241 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . 127 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 363 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 127 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . .
INDEX
NOTES
NOTES
