SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 7 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeep威 Wrangler and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle. Before you start to drive this vehicle, read the Owner’s Manual.
INTRODUCTION control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle and serious injury or death. Because of its open-body construction, your vehicle offers less protection than closed vehicles in the event of an accident. Roll Over Warning Label 5 Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S.
INTRODUCTION Operating this vehicle at excessive speeds or while intoxicated may result in loss of control, collision with other vehicles or objects, going off the road, or overturning, any of which may lead to serious injury or death. Also, failure to use standard seat belts subjects the driver and passengers to a greater risk of being thrown out of an open-body vehicle than out of a closed vehicle in an accident which can result in injury or death.
INTRODUCTION WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of vehicle through windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .13 䡵 Steering Wheel Lock — If Equipped . . . . . . . . . .17 ▫ Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Manually Lock The Steering Wheel . . . . . . .18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 ▫ To Release The Steering Wheel Lock . . . . . . . . .18 䡵 Sentry Key Immobilizer System — If Equipped . .14 䡵 Doors And Locks . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .26 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .45 ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags . . . . . . . . . .27 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .46 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. 2 Ignition Key Insert the key fully, then turn the switch to one of the four illustrated positions. The key can be inserted or withdrawn only in the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to LOCK, and remove the key. Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. CAUTION! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE keys that have been programmed to the vehicle can be used to start and operate the vehicle for longer than the 2 second validation time period. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the SKIM indicator light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Important Note About Service A four digit PIN number is needed to service the Sentry Key Immobilizer System. This number can be obtained from your authorized dealer. However, this number can also be found on your customer invoice that you were given upon receipt of your vehicle. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds, a chime will sound and the SKIM indicator light will begin to flash. Turn the ignition switch OFF and remove the second key. 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound. The SKIM indicator light will stop flashing, turn on for 3 seconds; then turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Manually Lock the Steering Wheel With the engine running, rotate the steering wheel 1/2 revolution from straight ahead position, turn off the engine and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To Release the Steering Wheel Lock Insert the key in the ignition and turn the wheel slightly to the right or left to disengage the lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Locks Doors on both hard-top and soft-top models are equipped with a rocker-type interior door lock. To lock a door when leaving your vehicle, press to the “Lock” position and close the door. Door Lock Knob 19 WARNING! • For personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will be carrying children too small for adult-size belts, your seat belts can also be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt cannot do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you cannot straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags 27 mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. NEVER ride in the front seat of a vehicle with a passenger front airbag, unless the airbag is turned off. An airbag deployment can cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 29 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Restraint Control (ORC) Module • Airbag Warning Light • Driver Airbag • Passenger Airbag • Steering Wheel And Column • Instrument Panel • Crash Sensor • Interconnecting Wiring • Knee Impact Bolsters How The Airbag System Works • The Occupant Restraint Control (ORC) Module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ORC detects a malfunction, the “Airbag Warning Light” will illuminate for a minimum of 12 seconds and will remain illuminated as long as the malfunction exists. WARNING! Ignoring the “Airbag Warning Light” in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags cannot protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. 33 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. Child Restraint Everyone in your vehicle needs to be buckled up all the time-babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The child seat is held in the vehicle by the lap belt, lap/shoulder belt, or the LATCH child restraint anchorage system. • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit in the vehicle’s seat belts properly. If the child cannot sit with knees bent over the seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer also recommends that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s instructions. • When your child restraint is not in use, secure it with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. In addition, there are tether strap anchorages behind the rear seat (on the floor behind each rear outboard seating position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forwardfacing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pull up on the shoulder portion of the lap/shoulder belt to tighten the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the child’s face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On hardtop models, keep the tailgate window closed when driving your vehicle. On fabric top models, do not drive with the rear window curtain up unless the side curtains are also open. This will prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires (including spare) for proper pressure. 47 Lights Have someone observe the operation of all exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 ▫ Tilting Front Seats . . . . . . . . . . . . . . . . . . . . . .59 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .52 ▫ Fold And Tumble Rear Seat . . . . . . . . . . . . . . .59 ▫ Inside Automatic Dimming Compass/Temperature Mirror — If Equipped . . . . . . . . . . . . . . . . . . .52 ▫ Removing The Rear Seat . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Parking Lights, Instrument Panel Lights, And Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .65 ▫ Headlight Dimmer Switch . . . . . . . . . . . . . . . .65 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . .66 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 ▫ Console Storage Compartment — If Equipped . .74 ▫ Putting Up The Soft Top . . . . . . . . . . . . . . . . 120 ▫ Add-A-Trunk™ — If Equipped . . . . . . . . . . . .74 ▫ Sunrider — If Equipped . . . . . . . . . . . . . . . . 127 䡵 Dual Top — If Equipped . . . . . . . . . . . . . . . . . .75 䡵 Door Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 ▫ Removing The Soft Top . . . . . . . . . . . . . . . . . .75 ▫ Door Frame Removal . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In some long, low speed traffic situations, the displayed temperature readings will be higher than the actual ambient temperature. This is considered normal. Accurate readings will resume with vehicle speed and sensor airflow. 53 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Calibration Automatic Calibration Once calibrated, the compass has the ability to selfcorrect for changes in magnetic field to keep the compass accurate. This is referred to as Automatic Calibration. If magnetic field changes are too great, the compass will enter CAL mode on it’s own and manual calibration will be required.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variation Adjustment Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map. NOTE: When the mirror is in the VAR mode, the letter “Z” will be displayed along with the currently selected zone number.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON, and press and hold the center button for 3 to 6 seconds. The last variance zone number will be displayed. Each press of the center button will select a new variance zone. When the proper zone is selected, wait 5 seconds to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. • Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. 57 SEATS WARNING! Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment Move seat forward or rearward by lifting the lever. Be sure the latch engages fully. Front Seat Adjustment — Recline To adjust seatback, lift lever, lean back, and release lever at desired position. To return seatback, lift the lever, lean forward and release the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 3 Tilting Front Seats Push the lever upward on the seatback to tilt the entire seat forward. Front Seat Tilt Lever Fold And Tumble Rear Seat To expand the cargo area: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Lift the seatback release lever and fold seatback forward. Folding Rear Seat 4. When completed, return seat to it’s normal position. Rear Seat Release Lever 3. Slowly flip the entire seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing the Rear Seat WARNING! • Press down on release bar on each side, and pull seat out and away from lower bracket. • Remove seat from the vehicle. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Replacing the Rear Seat Reverse steps for removing the seat. Be certain to pull the seat belts between the seat cushion and seatback. Position them for passenger use. TO OPEN AND CLOSE THE HOOD To open hood, first release both hood latches. WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and radiator support and lift up on handle to raise hood. You may have to push down slightly on hood before lifting up on handle. Insert the support rod into the slot in the radiator support. 63 To close the hood, remove the support rod from the radiator support and place it in the retaining clip. Lower the hood slowly, then let it drop the last few inches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the muti-function control lever fully upward. The overhead light will automatically turn off in about 20 minutes if a door is left open or the dimmer control is left in the dome light position. Turn the ignition switch ON to restore the overhead light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 NOTE: If the driver’s door is left open, and the headlights or parking lights are left on, the “High Beam Indicator Light” will flash and a chime will sound. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. Headlight Dimmer Switch Pull the multi-function control lever towards you to switch the headlights to HIGH beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Fog Lights — If Equipped The front fog light switch is in the multi-function control lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the end of the lever. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS CAUTION! Windshield Wiper Operation Move the lever upward to the second detent for LO speed wiper operation, or to the third detent for HI speed operation In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermittent interval previously selected. TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator operations at speeds greater than 35 mph (56 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory. Pressing the ON·OFF button or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. (If the vehicle speed drops below 35 mph (56 km/h), the Speed Control will automatically disengage). If this happens, you can push down on the accelerator pedal to maintain the desired speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off WARNING! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear passengers have cup holders at the rear of the center console. 73 STORAGE Glove Compartment To open the glove compartment, pull the latch up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Storage Compartment — If Equipped To unlock, insert key and turn. To open, press the latch button. Add-A-Trunk™ — If Equipped The factory-installed Add-A-Trunk™ option provides a secured compartment for parcels or equipment when the tailgate is closed and locked. To gain access to this compartment, simply open the tailgate and release the spring loaded latch pins. The cover of the Add-ATrunk™ can then be raised.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DUAL TOP — IF EQUIPPED If your vehicle is equipped with a Dual Top, you must remove one of the tops from the vehicle. The soft top was installed at the factory for shipping purposes only. The soft top and the hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top, should both tops remain on the vehicle at the same time. Removing The Soft Top 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Using a rubber mallet, carefully tap the knuckles from the outside edge. This will disconnect the bow assembly from the pivot bracket. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot bracket. Remove the brackets using a #T40 Torx威 head driver. Recover and re-zip the sports bar cover. Store pivot brackets and screws in a safe place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Installing the Soft Top NOTE: The following procedures are for first time set up only. For future soft top procedures, refer to “Soft Top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (4) • right and left quarter windows 6. Reinstall the hard top. Refer to “Hard Top Installation” in this section. • rear tailgate window. 2. Remove the hard top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. a. If the pivot brackets have been removed, unzip the sport bar cover and attach the pivot brackets and screws with a #T40 Torx威 head driver. Re-cover and re-zip sport bar cover. b. If the door frames have been removed, re-install them (refer to “Door Frame” in this section). c.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. NOTE: A visual instruction sheet is enclosed in the dual top wrap. 79 7. Remove the tailgate bar (black bar with end caps) that is located in the soft top and set aside. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 8.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Working from the rear of the vehicle with the tailgate open, lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 12. Move to the side of the vehicle and pull the side bow forward and down. You will see the 3 bow rise from the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 13. Unclip and move the sun visor to the side. 81 14. Open the header latches and engage the hooks on each side into the windshield slot. NOTE: Do not latch at this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 15. Grasp the drip rail retainers and untuck them from the door frame. The soft top fabric should cover the header completely from one side to the other. This may require you to pull some of the fabric down and around the corners. Repeat this step for the other side. For Unlimited Models — Pull the side bow forward and down. Make certain the blocks on the side bows line up with the retainers on the door rails. Ensure the blocks are locked in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. Make sure the nylon check straps between the 2 bow and 3 bow are not twisted or wrapped around the 2 bow. Move to the rear of the vehicle and gently pull the rear corners (sail panels) over the 3 bow letting them hang down. 83 NOTE: Do not tuck the sail panel retainers at this time. 17. Enter the vehicle and sit in the rear seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For Unlimited Models — Look up at the 3 bow and remove the four screws. Grasp the fabric rearward of the 3 bow, and pull it up and around, reinstalling all four screws through the existing fabric holes. (Refer to the Instruction Sheet in the soft top for additional information and photos). 18. Align the sail panel retainer to the edge of the body side retainer at the rear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panels. 19. To install the quarter windows, affix the rear corner of the quarter window temporarily to the Velcro威. Start and zip the zipper only about 1 inch (2.5 cm). At this time, it is necessary to tuck in the door frame retainer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 20. Tuck in the bottom retainers on the quarter windows into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 21. Locate the black retainer bar that was set aside, and the rear window. Remove and discard the end caps. Slide the retainer bar over the receiver at the bottom inside of the rear window with the bulky seal away from you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 22. Zip the rear window beginning from the left using both zipper ends. Run the upper zipper around the window to the right side leaving the lower zipper end at the start on the left. 87 23. Tuck in the retainer bar ends into the tailgate clips on each side of the tailgate opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 24. Tuck the lower retainers on both sides of the rear window under the tailgate clips. Reinstall the left sail panel if it was untucked to get the rear window zipper started. 25. Tuck the drip rail retainers into the door frame slots above the door on both sides.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 26. Close the header latches and return the sun visor to it’s secure position. 89 HARD TOP CAUTION! • The hard top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed. Hard Top Removal 1. Fold down the sun visors and move them to the side. 2. Unlatch the two hard top latches located at the top of the windshield. 3. Unbolt the six Torx威 head screws which secure the hard top to the vehicle using a #40 Torx威 head driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 NOTE: On a dual top vehicle, the two rear and center nuts are retained onto the bodyside. 4. Open both doors. 5. Open tailgate all the way to ensure clearance of the rear window glass. Lift rear window glass. CAUTION! When removing the 2 front screws just rearward of the doors, make sure that the nut does not fall into the seat belt retractor. Grasp the nut to prevent this from occurring.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Locate the wiring harness at the rear left side corner of the vehicle. CAUTION! 7. Disconnect the washer hose and install the tethered cap. Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pulling to disconnect. NOTE: If the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected from the hard top. 3 9. Remove the hard top from the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Hard Top Installation NOTE: If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. NOTE: The hard top must be positioned properly to ensure sealing. Set the hard top on the windshield frame so that there is no overhang.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Stow half doors carefully outside of the vehicle, never inside to avoid scratches. 2. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start with the rear retainer and work forward towards the windshield. Repeat this on the other side. 97 3. Unclip and move the sun visor to the side. 4. Release the header latches and leave the hooks in the windshield slots.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Open the tailgate, partially unzip the rear window on each side, and untuck the lower retainers on the window from the tailgate clips on both sides of the tailgate opening. 6. Pull the retainer bar straight out from the tailgate clips. • Remove the rear window entirely. This is done by unzipping the window by bringing both the right zipper and left zipper tabs all the way to the end of the zipper track at the bottom left corner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Beginning from the rear, moving forward, partially unzip the side window and untuck the bottom retainers. 99 9. Untuck the sail panels from the bodyside retainer. NOTE: If difficulty is experienced with fabric tension, place your hand on the rear upper corner of the top and pull down to help untuck the sail panels. 3 8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Completely release the hooks on the rear side of the windshield. Grasp the side bow behind the header and lift top back. 11. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. NOTE: If your vehicle is equipped with a Dual Top, prevent connector damage by ensuring that the hard top wire harness is folded back and secured to the main harness, using the attached Velcro威 strap. 12.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tuck the top material between the 2 bow and the 3 bow as it folds. 101 13. Tuck the top material between the 2 bow and the header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 15. After the top is folded down, tuck the check straps so that they are not hanging and flapping outside the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Putting Up The Soft Top NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. 1. Begin working from the rear of the vehicle, with the tailgate open. Lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 103 2. Move to the side of the vehicle and pull the side bow forward and down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Unclip and move the sun visor to the side. 4. Open the header latches and engage the hook on each side into the windshield slot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Grasp the drip rail retainer and untuck them from the door frame. 105 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. 3 NOTE: Do not tuck the drip rails into the door frame at this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Align the sail panel retainer to the edge of the bodyside retainer at the rear. Tuck the sail panel into the bodyside retainer beginning from the rear and working to the corner. Tuck the retainer around the corner and continue forward. NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panel retainers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. To install the quarter window, affix the rear corner of the window temporarily to the Velcro威. Start and zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 107 9. After the door frame retainer has been completely tucked in, finish zipping in the window. Then affix the Velcro威 flaps around the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. To assist in getting the zipper started, lay the retainer bar inside the vehicle on the wheel wells and uninstall half of the left sail panel from the bodyside retainer beginning at the tailgate to expose zipper ends.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper at the start. 109 13. Tuck the retainer bar into the tailgate clips.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Tuck the lower retainers of the rear window under the tailgate clips. Reinstall the left corner if it was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slot above the door on both sides.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Close the header latches and return the sun visor to it’s secured position. 111 SOFT TOP — SUNRIDER EQUIPPED MODELS CAUTION! • The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains. CAUTION! • Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • Do not lower the top when the temperature is below 41°F (5°C).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start at the back of the rear drip rail retainer and work forward towards the windshield. Repeat this on the other side. 3. Release the header latches and hooks from the windshield slots. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Grip and rotate the retainer bar up towards you to release it from the upper portion of the tailgate clips. The retainer bar runs along the bottom of the rear window. 115 will remain on the zipper track attached to the top. Pull up on the window to disengage zipper end. Stow window carefully to avoid scratching. 7. Undo the Velcro威 that runs along the top and rear edge of the side window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. NOTE: Stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the rear corners of the vehicle. NOTE: If difficulty is experienced with fabric tension, place your hand on the rear corner of the top and pull down to help untuck the corners.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Release the Sunrider pins to release the top bows from the brackets located on both door rails. Push up and back on the bow slightly so it does not fall back and lock into the brackets. 117 11. Grasp the side bow behind the header and lift the top back.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. For Unlimited Models — Tuck the top between the 2 bow and 2-1/2 bow and 2-1/2 bow and 3 bow as it folds. For Wrangler Models — Tuck the top between the 2 bow and 3 bow as it folds. 13. Make sure the sides of the top are folded inward as the top continues to fold, and check straps are clear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Tuck the top material between the 2 bow and the header. 119 15. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. After the top is folded down, tuck the check straps inside the rear corners of the vehicle. This will keep them from hanging and flapping outside the vehicle. Putting Up The Soft Top 17. Hook the header latches back onto the header to keep them from rattling. NOTE: Be sure the wire harness is not attached to the soft top bows before you lift the top. Make certain Sunrider sleeves are covering the Sunrider links. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Begin working from the rear of the vehicle with the tailgate open. Standing to the side of the vehicle, lift the top by the 2 bow and 3 bow over the sport bar. 121 For Wrangler Models — You may need to pull the Sunrider pins on the door rails in order to engage the header latches into the windshield slots. 3 4. Engage the hooks on each side of the header into the windshield slots and fully engage the header latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull the side bow forward and down. Make certain the blocks on the side bows line up with the retainers on the door rails. Lock the blocks in place. NOTE: Check to make certain the check straps are not tangled on any of the other top hardware. This will prevent the top from being put all the way up. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Tuck the sail panel retainer into the bodyside retainer. Begin working from the rear tailgate opening and work to the corner. 123 NOTE: This may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and pull down to help tuck in the sail panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. To install the quarter windows, affix the upper rear corner of the window temporarily using the Velcro威. Next, start the zipper about 1 inch (2.5 cm) at the upper forward corner of the window. At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has been completely tucked in, finish zipping in the window. Then affix the Velcro威 flaps around the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Tuck the bottom retainer on the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 125 11. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper in at the start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To assist in getting the zipper started, lay the bar inside the vehicle on the right wheel well, uninstall half of the left sail panel from the bodyside retainer, beginning near the tailgate open to expose zipper ends. 13. Tuck the lower retainers on the rear window under the tailgate clips. 12. Tuck the retainer bar into the upper portion of the tailgate clips.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3 14. Reinstall the corner of the sail panel that was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slots above the door on both sides. Start at the front next to the windshield and work rearward. 16. Return the sun visors to their secure position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise 2. Unclip and move the sun visors to the side. 1. Grasp the drip rail retainers and untuck both of them starting at the rear of the door frame slot. Repeat this on the other side. 3. Release the header latches, and slide the plastic sleeves forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Secure latches to plastic retainer on header. 129 5. Locate strap to secure the header to the sport bar. Wrap strap around sport bar and hook to header and tighten. 3 6. Attach and reposition sun visors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Lower 1. Remove strap from header and sport bar. 2. Release header latches from header retainer. 3. Unclip and move the sun visors to the side. 4. Grasp the front header and pull to the front of the vehicle. 5. Slide plastic sleeve rearward over Sunrider link. 6. Tuck drip rail retainers into the door frame slots. 7. Close the header latches, and return sun visors to their original position. NOTE: Sunrider is a trademark of Bestop, Inc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the door frames and store the knobs and door frames outside of the vehicle. Repeat this step for the other side. WARNING! • Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. • Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Slide door frame forward until the pin holes in the top line up with the holes in the side bar. Screw in the knobs and tighten, beginning with the front knob. Repeat procedures on the other side. FOLDING WINDSHIELD The fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Do not drive your vehicle on-road with the windshield down and the side bars removed as you lose the protection these structural elements can provide. speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred, if you are driving off-road with the windshield folded down. NOTE: Before lowering windshield, disconnect the electrical connector for the inside Compass/Temperature mirror (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Carefully follow these warnings to help protect against personal injury: • Do not drive your vehicle on-road with the windshield down. • Do not drive your vehicle unless the windshield is securely fastened, either up or down. • Eye protection, such as goggles, should be worn at all times when the windshield is down. • Be sure that you carefully follow the instructions for raising the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Remove the two Torx威 head screws holding each side bar to the windshield frame. Shift the side bar inboard to clear windshield pillar molding when removing the side bar. 135 4. Unzip the sport bar padding to expose the side bar bolts. Remove the two front and rear Torx威 head screws for each bar. Remove the side bars and rezip sport bar padding in place. 3 NOTE: Store all of the mounting bolts in their original threaded holes and tighten for safekeeping.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not remove the head impact foam from the side bars, as damage to the foam may result. 5. To safely store the side bars in your vehicle, use four of the cinch straps, found in the glove box. Attach the straps through the footman loops located in the floor behind the folded rear seat on each side of the vehicle. WARNING! You or others could be injured if you carry the side bars loose in your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Remove the black round headed windshield Torx威 head screw on each side of the base of the windshield. 137 8. Lower the windshield gently until it contacts the rubber hood bumpers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Secure the windshield by passing the remaining cinch strap, found in the glove box, through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising The Windshield And Replacing Side Bars To raise the windshield, install the windshield wipers, and install the side bars use these same steps in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES — HARD TOP ONLY Rear Window Defogger To turn the rear window defogger on, press the rocker switch. If you press the switch a second time, you will turn the defogger off. A light on the rocker switch will indicate the defogger is on. 139 The defogger will automatically turn off after about ten minutes. For five more minutes of operation, depress the top of the switch to turn the defogger on again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Wiper/Washer To utilize the rear wiper, press the switch to the first detent. To activate the rear washer, depress the switch to the second detent. The washer will continue to spray as long as the switch is held. The switch will return to the wiper mode when released. To turn the rear wiper off, lift the bottom of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Interior Controls . . . . . . . 145 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 153 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 146 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 153 䡵 Instrument Cluster Description . . . . . . . . . . . . . 147 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 153 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RBQ—AM/FM Stereo Radio With 6 Disc CD Changer . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 170 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 160 ▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 170 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 163 ▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 145 INSTRUMENT PANEL AND INTERIOR CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION Your vehicle is equipped with the instrument cluster described on the following pages. 1. Voltmeter Indicates available battery voltage and charging system operation. The lower red zone indicates that battery charge may be too low to start the engine. With the engine running, the normal operating range is between 11 and 15 volts.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. High Beam Indicator Light This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low. If the driver’s door is open, and the headlights or parklights are left on, the “High Beam Indicator Light” will flash and a chime will sound. 8. Seat Belt Indicator Light A warning chime and an indicator light will alert you to buckle the seat belts.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Oil Pressure Gauge Indicates engine oil pressure. This gauge does not indicate oil level, and pressure varies with engine speed, temperature and oil viscosity. Consistent lower readings indicate possible malfunction. Seek authorized service. 14. Coolant Temperature Gauge Indicates engine coolant temperature. The red zone to the far right indicates possible overheating. Seek authorized service immediately if the gauge operates in the red zone. In U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 20. Anti-Lock (ABS) Warning Light After ignition is turned on, illuminates to indicate function check at vehicle start-up. If light remains on after start-up or comes on and stays on at road speeds, it may indicate that the ABS has detected a malfunction or has become inoperative. The system reverts to standard non-anti-lock brakes. 151 If the parking brake is applied and the vehicle is in motion, the red BRAKE warning light will “flash” and a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 23. Fuel Cap Indicator This symbol indicates the side of the vehicle where the fuel cap is located. 24. Fuel Gauge The pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to E, for your safety, approximately 2 U.S. Gallons (7.6L) of fuel remain. NOTE: When the ignition switch is turned to OFF, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: On vehicles so equipped the radio, steering wheel radio controls and 6 disc CD/DVD changer will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up or the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL Audio The audio button controls the BASS, TREBLE, BALANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition OFF (except on convertibles). FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. To select Sirius Satellite Radio™ (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING YOUR INSTRUMENT PANEL show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player. Radio display will show “loading” when it is being loaded.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Press the TIME button to change the display from elapsed CD playing time to time of day. CD ERROR will appear on the display if the laser is unable to read the Disc data for the following reasons: • Warped disc Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. • Excessive vibration CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
UNDERSTANDING YOUR INSTRUMENT PANEL mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-5397474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Blower Switch The blower switch is the rotary knob to the left of the controls. The blower speed will increase as the knob is turned clockwise. There are four blower speeds. Mode Selection The mode selector is the right knob located on the climate controls. It can be set in any of the following positions: NOTE: The blower motor will run until the mode control knob is turned to the “Off” (“O”) position or the ignition is turned OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Outside air comes from both instrument panel and floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Defrost Outside air comes from the windshield outlets with a slight amount of air being directed through the floor and demisters. Use this setting when necessary to defrost or defog your windshield. Floor Air Conditioning — If Equipped Outside air comes from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 Mode Selection The mode selector is the right knob located on the climate controls. It can be set in any of the following positions: 4 Temperature Control Knob You can choose your degree of comfort by rotating the knob. The coldest setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region).
UNDERSTANDING YOUR INSTRUMENT PANEL Off Turning the rotary knob to this position shuts off the blower motor and outside air will not come through any outlet. Recirculation Select this position when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior air only. Air flows through the panel outlets in this mode. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL Mix Outside air comes from the floor and defrost outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keeping the windshield clear. Defrost Outside air comes from the windshield outlets with a small amount being directed through the floor outlets. Use this setting when necessary to defrost your windshield. NOTE: For improved safety, the A/C compressor is activated when “Mix” or “Defrost” modes are selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging In mild but rainy or humid weather, the windows might fog on the inside. To clear the fog off all of the windows, turn the mode control knob to the “Panel” position (with snowflake). Adjust the temperature control and blower speed to maintain comfort. Direct the panel outlets toward the side windows. Interior fogging on the windshield can be quickly removed by selecting the “Defrost” position.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 182 䡵 Transmission Shifting . . . . . . . . . . . . . . . . . . . . 185 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 182 ▫ 6-Speed Manual Transmission . . . . . . . . . . . . 185 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 182 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 188 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Axle Lock (Tru–Lok™) — If Equipped . . . . . . . . 199 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 213 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 200 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 213 䡵 About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 203 ▫ Tire Identification Number (TIN) . . . . . . . . . . 216 䡵 Anti-Lock Brake System — If Equipped . . . . . . .
STARTING AND OPERATING 181 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 236 䡵 Tire Rotation Recommendations . . . . . . . . . . . . 228 ▫ Common Towing Definitions . . . . . . . . . . . . . 236 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 229 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . . 238 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual Transmission Apply the parking brake, place the gearshift control lever in N (Neutral) and depress the clutch pedal before starting vehicle.
STARTING AND OPERATING 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal starting procedure. 183 Extreme Cold Weather (below –20°F or –29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended. If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded.
STARTING AND OPERATING If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. After Starting The idle speed will automatically decrease as the engine warms up.
STARTING AND OPERATING 185 WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. 5 TRANSMISSION SHIFTING 6-Speed Manual Transmission Follow the shift pattern on the gearshift knob. NOTE: The backup lights will come on when your vehicle is in reverse gear and the ignition is in the ON position.
STARTING AND OPERATING WARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. • Do not operate at sustained high engine or road speeds in lower gears. Engine damage may result. • Do not downshift into a low gear while traveling at too high a speed for that gear. Engine, clutch, or transmission damage may result.
STARTING AND OPERATING • When “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended Manual Transmission Shifting Speeds Manual Transmission Shift Speeds in MPH (KM/H) Engine Speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 2.4L Accel. 14 (23) 24 34 46 57 (39) (55) (74) (92) Cruise 11 (18) 19 27 38 45 (31) (43) (61) (72) 4.0L Accel.
STARTING AND OPERATING 3. Be sure to re-engage the clutch interlock safety feature by following these steps in reverse order when you are finished off-road driving. Automatic Transmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING R (Reverse) For moving the vehicle rearward. Always stop before moving the lever to R (Reverse), except when rocking the vehicle. N (Neutral) Engine may be started in this position. NOTE: Towing the vehicle, coasting, or otherwise driving with the transmission in N (Neutral) can cause severe damage to the transmission. WARNING! Do not coast in N (Neutral) and never turn off the ignition to coast down a hill.
STARTING AND OPERATING When frequent transmission shifting occurs while using Overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off overdrive will improve performance and extend transmission life by reducing excessive shifting and heat buildup. Overdrive can be locked out by pressing the O/D OFF switch located on the instrument panel.
STARTING AND OPERATING 193 WARNING! CAUTION! Never use P (Park) position with an automatic transmission as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Before moving the shift lever out of P (Park), you must turn the ignition from LOCK so the steering wheel and shift lever are released. Otherwise, damage to steering column or shifter could result.
STARTING AND OPERATING NOTE: The transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation in D (Drive) position. If the transmission becomes hot enough, the TRANS TEMP warning light in the instrument cluster will come on.
STARTING AND OPERATING Operating Instructions/Precautions The transfer case provides four mode positions — two (rear) wheel drive high range, four wheel drive high range, neutral, and four wheel drive low range. This transfer case is intended to be driven in the two wheel drive (2H) position for normal street and highway conditions such as dry hard surfaced roads.
STARTING AND OPERATING Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 4H Position Four Wheel Drive High Range — Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces. NOTE: This range should not be used during dry pavement operation. N (Neutral) Position Neutral — Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in Section 5 of this manual.
STARTING AND OPERATING is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case N (Neutral). NOTE: Pausing in transfer case N (Neutral) in vehicles equipped with an automatic transmission may require shutting the engine OFF to avoid gear clash while completing the shift. If difficulty occurs, shift the automatic transmission to N (Neutral), hold foot on brake, and turn the engine OFF. Make shift to desired mode.
STARTING AND OPERATING slight application of the accelerator will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight application of the parking brake may be necessary to gain maximum traction. 199 AXLE LOCK (TRU–LOK™) — IF EQUIPPED The Axle Lock switch is located on the lower center of the instrument panel. WARNING! On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground.
STARTING AND OPERATING • Vehicle speed should be 10 mph (16 km/h) or less. To activate the system, press the switch once to lock the rear axle only (the REAR LOCK indicator light will illuminate), press the switch again to lock the front axle (the FRONT LOCK indicator light will illuminate). Once the rear axle is locked, pressing the switch again will lock or unlock the front axle. NOTE: The indicator lights will flash until the axles are fully locked or unlocked.
STARTING AND OPERATING 201 If the parking brake is not completely released, the BRAKE warning light will remain on. NOTE: Your vehicle has automatically adjusting rear brakes and we do not recommend any adjustment other than the maintenance performed by your authorized dealer.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave a automatic transmission in P (Park), or a manual transmission in 1st gear. Make certain the transfer case is in gear. Failure to do so may cause the vehicle to roll and cause damage or injury.
STARTING AND OPERATING ABOUT YOUR BRAKES Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING WARNING! To use your brakes and decelerate more safely, follow these tips: • • • • • • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
STARTING AND OPERATING WARNING! To help avoid personal injury, follow these tips: • Never reach through the steering wheel to operate steering column controls. Injury to your hands or loss of vehicle control may result. • If the engine stalls or power assist fails due to a malfunction, vehicle steering and braking will require greater effort. ANTI-LOCK BRAKE SYSTEM — IF EQUIPPED The Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING The Anti-Lock Brake System pump motor runs during the self-test and during an ABS stop to provide the regulated hydraulic pressure. The motor pump makes a low humming noise during operation, this is normal. During off-road use, loss of traction can temporarily defeat the system and cause the warning light to illuminate. Turn the ignition OFF and ON again to restore Anti-Lock Brake System function.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the power steering pump may occur.
STARTING AND OPERATING OFF-ROAD DRIVING TIPS When To Use 4L (Low) Range When off-road driving, shift to 4L (Low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power. This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L (Low) range.
STARTING AND OPERATING and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches. The flowing water can erode the streambed causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting. Standing Water Avoid driving in standing water deeper than 20 inches, and reduce speed appropriately to minimize wave effects. Maximum speed in 20 inches of water is less than 5 mph (8 km/h).
STARTING AND OPERATING If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine and shift to R (Reverse). Back slowly down the hill allowing the compression braking of the engine to help regulate your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires.
STARTING AND OPERATING After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 213 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 215 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 217 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressures are listed on the lower front inside corner of the driver door opening.
STARTING AND OPERATING 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 221 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Over inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING 225 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your authorized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Install chains on rear tires only. Tire chains may be installed on all models except the Sahara and Rubicon.
STARTING AND OPERATING 229 These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual.
STARTING AND OPERATING premium gasoline will provide no benefit over high quality regular gasoline, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations.
STARTING AND OPERATING CAUTION! DO NOT use gasoline containing METHANOL. Gasoline containing methanol may damage critical fuel system components. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles.
STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. 233 FUEL FILLER CAP (GAS CAP) The fuel cap is located on the left side of the vehicle. If the fuel cap is lost or damaged, be sure the replacement cap is for use with this vehicle. • Guard against carbon monoxide with proper maintenance.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. • Turn the engine off. • Rotate the fuel cap to the left to remove.
STARTING AND OPERATING 235 WARNING! WARNING! • Remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING • Make sure that the fuel cap tether strap is not caught under the fuel cap. • Be sure to remove the key. CAUTION! TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING 237 Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING Frontal Area The maximum height and maximum width of the front of a trailer. Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
STARTING AND OPERATING Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1 587 kg) Duty Class III - Heavy Duty 5,000 lbs (2 268 kg) Class IV - Extra 10,000 lbs (4 540 kg) Heavy Duty All trailer hitches should be professionally installed on your vehicle.
STARTING AND OPERATING Engine/ Transmission 2.4L/ Manual Model 4.0L/All 4.0L/ Automatic Unlimited GVWR (Gross Vehicle Wt. Rating) 4,350 lbs (1 973 kg) GCWR (Gross Combined Wt. Rating) 5,350 lbs (2 427 kg) Frontal Area Max. GTW (Gross Trailer Wt.) 1,000 lbs (453 kg) 25 Sq. Ft. (2.32 square meters) 4,250 lbs (1 928 6,250 lbs (2 835 25 Sq. Ft. 2,000 lbs (907 kg) kg) (2.32 square kg) meters) 4,600 lbs (2 086 8,100 lbs (3 674 32 Sq. Ft. 3,500 lbs (1 587 kg) kg) (2.
STARTING AND OPERATING which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. 241 Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: NOTE: Trailer towing requires special rear axle lubricant. Refer to “Fluids, Lubricants, and Genuine Parts” in Section 7 for more information. CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle.
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. With a manual transmission, shift the transmission into reverse.
STARTING AND OPERATING Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage.
STARTING AND OPERATING 245 CAUTION! WARNING! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected.
STARTING AND OPERATING Towing Tips — Cooling System To reduce potential for engine and transmission overheating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning Turn off temporarily. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (Neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2. Shift automatic transmission into N (Neutral) or depress clutch pedal on manual transmission. 3. Shift transfer case lever into N (Neutral). 4. Start engine. 5. Shift automatic transmission into D (Drive) or manual transmission into gear. 6.
STARTING AND OPERATING Shifting Out Of Neutral (N) Use the following procedure to prepare your vehicle for normal usage. 1. Shift automatic transmission into N (Neutral) or depress clutch pedal on manual transmission. 2. Shift transfer case lever into desired position. 3. Shift automatic transmission into D (Drive) or release clutch on manual transmissions.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 252 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 256 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 253 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 256 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 254 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 258 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
WHAT TO DO IN EMERGENCIES Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, and you hear continuous chimes, turn the engine off immediately, and call for service. JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES 255 Jack Location The jack and lug wrench are stored under the front passenger seat. The jack handle driver and jack extension are located in a kit that is stored on the floor board to the right of the front passenger seat. On some models, this tool kit is under the carpeting in the same location. To remove the jack from its stowage position, turn the thumb screw counterclockwise to loosen jack, and then remove it from the bracket.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: If you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire.
WHAT TO DO IN EMERGENCIES 4. Operate jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. 257 and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Remove jack assembly and wheel blocks.
WHAT TO DO IN EMERGENCIES Set the parking brake, place an automatic transmission in P (Park) (or N (Neutral) for a manual transmission). Turn off lights, heater, and other electrical loads. Observe charge indicator in the battery. If indicator is light or yellow, replace the battery. 259 1. Attach one end of the jumper cable to the positive terminal of the discharged battery and the other end of the same cable to the positive terminal of the booster battery.
WHAT TO DO IN EMERGENCIES WARNING! • Do not connect the cable to the negative terminal of the discharged battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting to jump start. 3.
WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out the battery vent. • Personal injury or property damage due to battery explosion. • Damage to charging system of booster vehicle or of immobilized vehicle. 261 TOWING A DISABLED VEHICLE The manufacturer recommends towing with all four wheels off the ground.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Drive Belts — Check Condition And Tension . . 275 䡵 4.0L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 275 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 268 ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 275 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 280 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 294 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 281 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ Driveline And Steering Component Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 282 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . . 296 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 265 ▫ Front Side Marker . . . . . . . . . . . . . . . . . . . . . 311 䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 311 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 315 ▫ Rear Tail, Stop, Turn Signal, And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 267 4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
MAINTAINING YOUR VEHICLE 271 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding 1 U.S. Quart (0.95L) of oil when the reading is at the ADD mark will result in a SAFE reading on these engines.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Taxi, Police, or delivery service (commercial service) • Trailer towing • Off-road or desert driving • If equipped for and operating with E–85 (ethanol) fuel If ANY of these apply to you, then change your engine oil at every interval shown in schedule “B” of the “Maintenance Schedules” section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (2.4L Engines) SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap shows the recommended engine oil viscosity for your vehicle. Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil.
MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar威 engine oil filters are high quality oil filters and are recommended.
MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. 277 Engine Timing Belt — 2.4L Engine Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition Wiring System — 2.4L Engine • Do not try to start the engine by pushing or towing the vehicle.
MAINTAINING YOUR VEHICLE Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent replacement of the fuel filter which is mounted in the fuel tank may be necessary. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on “Maintenance Schedule A.
MAINTAINING YOUR VEHICLE WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery. 279 To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required.
MAINTAINING YOUR VEHICLE Driveline And Steering Component Lubrication U-joints (cardan joints) are sealed and do not require lubrication. Prop shafts, yokes, ball joints and other driveline and steering components may be provided with grease fittings for lubrication. Lubrication of these components at the intervals specified in the appropriate “Maintenance Schedule” in Section 8 is very important, particularly if your vehicle is subjected to off-road or other heavy-duty use.
MAINTAINING YOUR VEHICLE remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. 283 reservoir with windshield antifreeze (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system for a few seconds to flush out the residual water. Windshield Washers WARNING! Commercial windshield washer solvents are flammable. They could ignite and burn you.
MAINTAINING YOUR VEHICLE have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
MAINTAINING YOUR VEHICLE With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of antifreeze/coolant from the radiator drain cock. If the cap is sealing properly, the antifreeze/coolant will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of antifreeze/coolant other than the specified HOAT antifreeze/coolant may result in decreased corrosion protection and engine damage. If a non-HOAT antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coolant as soon as possible. • Do not use plain water alone or alcohol base antifreeze/coolant products.
MAINTAINING YOUR VEHICLE 287 Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
MAINTAINING YOUR VEHICLE children, do not store ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate.
MAINTAINING YOUR VEHICLE • Check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze/ coolant needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent antifreeze/coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
MAINTAINING YOUR VEHICLE are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the appropriate “Maintenance Schedule” in Section 8 for suggested service intervals. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
MAINTAINING YOUR VEHICLE 291 WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the BRAKE warning light shows system failure Be sure to clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. WARNING! • Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE (cross-hatched area) on the oil level indicator. The fluid level indicator should be in the COLD region at 70° F (21° C) fluid temperature. If the fluid level is low, add sufficient fluid to bring to the proper level. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid is added through the dipstick tube.
MAINTAINING YOUR VEHICLE 295 Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. Transfer Case Fluid Level Check The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position.
MAINTAINING YOUR VEHICLE CAUTION! Front/Rear Axle Fluid When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Fluid Level Check Lubricant should be at bottom edge of the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.
MAINTAINING YOUR VEHICLE Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Maintenance After Off-Road Driving After extended operation in mud, sand or water, or similar dirty conditions, have your brake drums, brake linings, and axle joints inspected and cleaned as soon as possible. This will prevent any abrasive material from causing excessive wear or unpredictable braking action.
MAINTAINING YOUR VEHICLE trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. • Insects, tree sap and tar.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar威 Touch Up Paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar威 Total Clean to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue.
MAINTAINING YOUR VEHICLE Follow These Steps To Remove The Carpet: 1. Unsnap the front and rear floor carpets. A snap is located on the outboard side of each front seat. 2. Remove the attachment cap from the front footwell area on both the driver and passenger side. The cap is removed by pulling it straight out. 2. Attach the carpet to the studs in the footwell and press on the attachment caps to secure the carpet. 3. Place rear floor carpet in vehicle and snap rear carpet to front floor carpet. 4.
MAINTAINING YOUR VEHICLE • Do not use harsh cleaners or bleaching agents on top material, as damage may result. 303 Care Of Fabric Top Windows • Do not allow any vinyl cleaner to run down and dry on the paint, leaving a streak. CAUTION! • After cleaning your vehicle’s fabric top, always make sure it is completely dry before lowering.
MAINTAINING YOUR VEHICLE 3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de-icing chemicals. Use warm water only if you must clean the window quickly. 5. Debris (sand, mud/dirt, dust, or salt) from off-road driving will have a major impact on zipper operation. Even normal on-road driving and vehicle washing will eventually impact window zipper operation.
MAINTAINING YOUR VEHICLE FUSE PANEL Interior Fuses The fuse panel is located behind the glove box. 305 To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orientation, engage the hinge hook formations on the lower edge of the glove box door with the hinge pins on the lower edge of the instrument panel.
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 9 10 11 Fuse Description 20 Amp Yellow Park Lights, Skim (Sentry Key) 20 Amp Yellow Stop Lights 20 Amp Yellow Subwoofer System 10 Amp Red Door Switch Defeat 10 Amp Red Airbag 20 Amp Yellow Rear Wiper 10 Amp Red Back-Up Lights, Rear Window Defroster Relay, ABS 10 Amp Red HEVAC 10 Amp Red Airbag 10 Amp Red Instrument Cluster 10 Amp Red Solenoids, DRL Cavity 12 Fuse 10 Amp Red 13 14 15 10 Amp Red 10 Amp Red 10 Amp Red 16 10 Amp Red 17 25 Amp Natur
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Your vehicle is equipped with an electrical power distribution center located in the engine compartment near the battery. This power center houses plug-in “Cartridge” fuses, ISO relays, and Mini (Micro) fuses. Power Distribution Center 307 A label inside the latching cover of the center identifies each component for ease of replacement, if necessary. Cartridge and mini (micro) fuses can be obtained from your authorized dealer.
MAINTAINING YOUR VEHICLE Cavity 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Fuse/Color 40 Amp Green Open 50 Amp Red Open 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Lt.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: 309 REPLACEMENT BULBS — IF EQUIPPED • Store the removed IOD fuse in the Power Distribution Center location #11 labeled “IOD Storage.” Interior Lights Bulb Type Auto. Trans. Indicator Light . . . . . . . . . . . . . . . . . 658 Courtesy Lights, Under Dash (1) . . . . . . . . . . . . . . 906 Heater Control Lights (2) . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE Exterior Lights Bulb Type Backup Lights (2). . . . . . . . . . . . . . . . . . . . . . . . 1156 Center High Mounted Stop Light (1) . . . . 921 or W16W Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H3 Front Park/Turn Lights (2) . . . . . . . . . . . . . . . . . 3157 Front Side Marker Lights (2) . . . . . . . . . . 168 or W3W Headlights (2) . . . . . . . . . . . . . . . . . . . . . . H 6024BL Stop/Tail/Turn Lights (2) . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 4. Remove and replace the lamp. 311 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front Side Marker 1. Reach under the front fender and locate the front side marker socket. 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front Fog Light Front Park/Turn Signal 1.
MAINTAINING YOUR VEHICLE 3. Squeeze the bulb/element spring retainer from the reflector. 4. Disconnect the electrical connector. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, and Back-Up Lights 1. Remove the screws attaching the lens to the tailight housing. 313 Center High Mounted Stop Light (CHMSL) The stop lamp is mounted on a bracket that extends upward from the tailgate. Remove the two screws holding the lens in place. Take the lens off and pull the bulb from the socket. 7 2. Separate the lens from the housing. 3. Push the bulb in, turn it counter-clockwise 1/3 turn, then remove it from the housing, and replace.
MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 2.4 Liter Engine (SAE 5W-30, API Certified Engine Oil) 4.0 Liter Engine (SAE 10W-30, API Certified Engine Oil) Cooling System * 2.4 Liter Engine (Mopar威 Antifreeze/Engine Coolant 5 Year/ 100,000 Mile Formula) 4.0 Liter Engine (Mopar威 Antifreeze/Engine Coolant 5 Year/ 100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 19 Gallons Metric 71.9 Liters 5 Qts 6 Qts 4.7 Liters 5.
MAINTAINING YOUR VEHICLE 315 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (4.0L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) API Certified SAE 5W-30 Engine Oil is recommended for the 2.4L engine. API Certified SAE 10W-30 Engine Oil is recommended for the 4.0L engine.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Manual Transmission Transfer Case Axle Differential (Front) Axle Differential (Rear) Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid Mopar威 Manual Transmission Lubricant or equivalent (meeting the requirements of DaimlerChrysler Material Standard MS-9224) Mopar威 ATF+4 Automatic Transmissi
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 318 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 321 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 318 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 318 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Off-road or desert driving • If equipped for and operated with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “Schedule B” of the “Maintenance Schedules” section of this manual.
M A I N T E N A N C E S C H E D U L E S 8 320 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect brake hoses.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
M 322 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the manual transmission fluid, add as necessary.
M 324 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the ignition cables (2.4L Only). Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
M 326 SCHEDULE “B” A I N Miles T (Kilometers) E N Inspect the drive belt and replace as needed. Not A required if belt was previously. N C Drain and refill the transfer case fluid. E Flush and replace the engine coolant/anti-freeze.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced.
M 328 SCHEDULE “B” A I 78,000 N Miles T (Kilometers) (130 000) E X N Change the engine oil and engine oil filter, if not replaced A at 3 months. N X C Rotate the tires. E Inspect the engine air filter element, replace if necessary. S C H E D U L E S 8 Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Replace the timing belt (2.4L Only)〫. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Drain and refill the front and rear axle fluid‡ Inspect the drive belt and replace as needed. Not required if belt was previously replaced.
M 330 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Inspect the engine air filter element, replace if S C H E D U L E S 8 necessary. Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Replace the ignition cables (2.4L Only). Lubricate the steering linkage tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Inspect the drive belt and replace as needed. Not required if belt was previously replaced. Drain and refill the transfer case fluid. Flush and replace the engine coolant/anti-freeze, if not replaced at 102,000 miles (170 000 km). 108,000 (180 000) Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. † Applies only if vehicle is used for frequent trailer towing or fleet/commercial service.
M 332 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change the engine oil and engine oil filter. E Rotate the tires. S C H E D U L E S 8 Inspect the engine air filter element, and replace if necessary. Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the manual transmission fluid, add as necessary. Inspect the transfer case fluid.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Lubricate the steering and suspension ball joints. Lubricate the steering linkage joints and outer tie rod ends. Inspect the brake linings.
M 334 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Inspect the engine air filter element, and replace if necS C H E D U L E S 8 essary. Inspect the PCV Valve, and replace if necessary.〫 Replace the ignition cables (2.4L Only). Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Flush and replace the engine coolant/anti-freeze. Inspect the manual transmission fluid, add as necessary. Inspect transfer case fluid.
M 336 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Inspect the engine air filter element, and replace if necessary. S C H E D U L E S 8 Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Inspect the drive belt, and replace as needed.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if necessary. Replace the ignition cables (2.4L Only). Inspect the PCV Valve, and replace if necessary.〫 Replace the spark plugs. Lubricate the steering linkage joints and outer tie rod ends. Lubricate the steering and suspension ball joints. Inspect the brake linings. Replace the timing belt (2.4L Only).〫 Inspect the drive belt, and replace as needed.
M 338 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Inspect the manual transmission fluid, add as necessary. N C Drain and refill the transfer case fluid. E Flush and replace the engine coolant/anti-freeze, if not done at S C H E D U L E S 8 102,000 miles (170 000 km). Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ Prepare For The Appointment . . . . . . . . . . . . 340 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 340 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 343 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 343 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 344 ▫ Be Reasonable With Requests .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 203 ABS (Anti-Lock Brake System) . . . . . . . . . . . . 151,205 Add-A-Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 141 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 278 Air Conditioner Maintenance . . . . . . . . . . . . . . . 280 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 174 Air Conditioning Controls . . . . . . . . . . .
INDEX Emergency Starting . . . . . . . . . . . . . . . . . . . . . 258 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Body Mechanism Lubrication . . . . . . . . . . . . . . . 282 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 217 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Anti-Lock (ABS) . .
INDEX Child Restraint Tether Anchors . . . . . . . . . . . . . 38,39 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 172 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Clutch Interlocking Ignition System . . . . . . . . 182,187 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 171 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Compass Calibration . . . . . . . . . . . . . . . . . . . . . . 54 Compass Variance . . . . . . . . .
INDEX Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 271 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 261 Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Used Coolant (Antifreeze) . . . . . . . . . . . . . . . . 287 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Oil Pressure Gauge . . . . . . . . . . . . . . . . . . . . . 149 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 314 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 149 Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Engine Oil Viscosity .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Four Wheel Drive Operation . . . . . . . . . . . . . 194,195 Front Axle (Differential) . . . . . . . . . . . . . . . . . . . 296 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . . 233 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Gauge . . . . . . . . .
INDEX Dimmer Switch . . . . . . . . . . . . . . . . . . . . . . . . 65 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 184 High Beam Indicator . . . . . . . . . . . . . . . . . . . . . 148 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 14 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Lane Change and Turn Signals . . . . . . . . . . . . . . 147 Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 20 LATCH (Lower Anchors and Tether for CHildren) . . . . . 38,39 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 229 Lights . . . . . . . . . . . .
INDEX Turn Signal . . . . . . . . . . . . . . . . . . . 66,147,311,313 Warning (Instrument Cluster Description) . . . . . 147 Loading Vehicle Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Locking Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 230 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Off-Pavement Driving (Off-Road) . . . . . . . . . . . . 209 Off-Road Driving (Off-Pavement) . . . . . . . . . . . . 209 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 Dipstick . . . . . . . . . . . . . .
INDEX Radio (Sound Systems) . . . . . . . . . . . . . . . . . 154,160 Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . 296 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 139 Rear Window Features . . . . . . . . . . . . . . . . . . . . 139 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 140 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 52 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . . 58 Recreational Towing . . . . . . . .
INDEX Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Rear Seat Cushion Removal . . . . . . . . . . . . . . . . 61 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Selection of Oil . .
INDEX Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 207,281 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Wheel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73,309 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 309 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . .
INDEX Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 240 Torque Converter Clutch . . . . . . . . . . . . . . . . . . 194 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236,261 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 261 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 248 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Trac-Lok Rear Axle . . . . . . .
INDEX Vehicle Modifications/Alterations . . . . . . . . . . . . . . 9 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . . 309 Viscosity, Engine Oil . . . . . . . . . . . . . . . . . . . . . . 274 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Warning Lights (Instrument Cluster Description) . 147 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 7 Warranty Information . . . . . . . . . . . . . . . . . . . . . 343 Washer, Adding Fluid . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
