SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8 ▫ Roll Over Warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION Thank you for selecting a Jeep威 Grand Cherokee and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and handling will have a different feel from what drivers experience with other vehicles, so take time to become familiar with your vehicle.
INTRODUCTION Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury. Drive carefully. 5 Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S.
INTRODUCTION NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar威 parts, and is interested in your satisfaction.
INTRODUCTION 7 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .14 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 䡵 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .19 䡵 Sentry Key Immobilizer System . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Battery Service . . . . . . . . . . . . . . .23 ▫ Lap/Shoulder Belt Operating Instructions . . . . .36 䡵 Remote Starting System — If Equipped . . . . . . . .24 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .40 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ Automatic Locking Mode — If Equipped . . . . .40 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .26 ▫ Energy Management Feature . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .65 13 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Ignition Key Removal Place the shift lever in P (Park). Turn the ignition switch to the OFF position, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. CAUTION! An unlocked car is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a malfunction in the electronics. If the bulb begins to flash immediately after the ignition switch is turned on, this indicates that an invalid key is being used to start the vehicle. Both of these conditions will result in the engine being shut down after 2 seconds of running.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Replacement Keys Customer Key Programming NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle. You can program new keys to the system if you have two valid keys by doing the following: At the time of purchase, the original owner is provided with a four digit PIN number.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound. The SKIM indicator light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this process to program up to a total of 8 keys. General Information The Sentry Key Immobilizer System complies with FCC rules part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the door lock plunger located on the inside of the doors or with the driver’s door key lock cylinder, will not set the alarm. 19 the system. The Security Alarm System will not disarm with a manual unlock, either through the lock plunger located on the inside of the door, or through a key in the driver’s door key cylinder. To Disarm the System To disarm the system, use the remote keyless entry transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of P (Park), all the transmitter buttons are disabled for all keys. Five Button Transmitter Four Button Transmitter To Unlock the Doors Press and release the “Unlock” button on the transmitter once to unlock the driver’s door, or twice to unlock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If desired, the system can be programmed to unlock all doors on the first press of the “Unlock” button. Refer to “Remote Unlock Driver’s Door 1st” in the Personal Settings section of the “Electronic Vehicle Information Center (EVIC)”, or simply follow these steps: 1. Press and hold the “Lock” button for 4 to 10 seconds. 2. While the “Lock” button is pressed, (after 4 seconds) press the “Unlock” button. Release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Using The Panic Alarm To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. While the “Unlock” button is pressed, (after 4 seconds) press the “Lock” button. Release both buttons. If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the transmitter buttons facing down, remove the small screw, and separate the two halves of the transmitter. Make sure not to damage the rubber gasket during removal. 3. To reassemble the transmitter case, join the two halves of the case together. Install and tighten the screw until snug. Make sure there is an even “gap” between the two halves. Test transmitter operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 unlocked, you have 60 seconds to enter the vehicle, insert the key into the ignition, and move it to the RUN position. Otherwise, the engine will cancel remote start and automatically turn off. Remote start will also cancel if any of the following occur: Remote Start Button Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the “Remote Start” button twice within two seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic Door Locks If this feature is selected your door locks will lock automatically if the vehicle speed is above 15 mph (24 km/h) and all doors are closed. It will reset whenever a door is opened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. 2 Power Window Switches The power window switches remain active for up to 10 minutes after the ignition switch has been turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. 2 Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up: Pull the window switch up and close the window completely, then pull and hold the switch for 1 second.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. 2 Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. NOTE: If a power malfunction to the power liftgate latch should occur, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 2 Latch Plate 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 39 6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best. As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Control (ORC) Module. Like the front airbags, the pretensioners are a single use item. After a collision that is severe enough to deploy the airbags and pretensioners, they must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental Restraint Systems (SRS) 43 This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The Occupant Restraint Control (ORC) Module determines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direction provided by the ORC. The ORC will detect roll overs, not rear impacts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates are possible, based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy when the Occupant Restraint Control (ORC) Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 51 Maintaining Your Airbag System Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and seat belt retractor assembly, replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • Does not come on during the 6 to 8 seconds after the ignition switch is first turned on. • Remains on after the 6 to 8 second interval. • Comes on for any period of time while driving.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating position. • Buckle the child into the restraint exactly as the manufacturer’s instructions tell you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Tether Strap Mounting Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a 61 means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned on. If the bulb is not lit during starting, have it replaced.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .72 ▫ Automatic Dimming Mirror — If Equipped . . . .72 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .73 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .74 ▫ Power Folding Outside Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Advanced Phone Connectivity . . . . . . . . . . . . .92 ▫ Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory . . . . . . . 107 ▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . .94 ▫ Memory Position Recall . . . . . . . . . . . . . . . . . 108 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ To Disable A Transmitter Linked To Memory . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 ▫ Daytime Running Lights — If Equipped . . . . . 116 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 124 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 117 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . . 124 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 117 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . . . 126 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ To Activate . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ BAS (Brake Assist System) . . . . . . . . . . . . . . . 131 ▫ Turning The Rear Camera Off . . . . . . . . . . . . 145 ▫ ERM (Electronic Roll Mitigation) . . . . . . . . . . 132 䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . . 145 ▫ ESP (Electronic Stability Program) . . . . . . . . . 133 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 145 ▫ ESP/BAS Warning Lamp And ESP/TCS Indicator Light . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 ▫ Closing Sunroof - Express . . . . . . . . . . . . . . . 154 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . 159 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 154 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . 159 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . . 154 ▫ Rear Storage Compartment . . . . . . . . . . . . . . 159 ▫ Venting Sunroof - Express . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Both mirrors will always move together and will fold anytime the knob is turned. The ignition switch does not have to be in the ON position. Driver’s Outside Automatic Dimming Mirror — If Equipped If your vehicle is equipped with a driver’s outside automatic dimming mirror, it operates when the inside automatic dimming mirror is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this section for details. (See page 106 for more information.) Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operations Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. NOTE: • www.chrysler.com/uconnect Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • System will prompt you to say the name of the person you want call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect™ phonebook. Refer to ⬙Add Names to Your UConnect™ Phonebook,⬙ to learn how to store a name in the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ⬙Voice Recognition’ button during the playing of the desired name, and then say ⬙Call.⬙ NOTE: the user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls.⬙ To combine two calls, refer to ⬙Conference Call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination To end a call in progress, momentarily press the ⬘Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete language selection. • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Towing Assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word ⬙Send.⬙ For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’ button and say ⬙3 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • At the next prompt, say ⬙Delete⬙ and follow the prompts. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnect™ System Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support. 101 8 - Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. NOTE: The 4 - way seat does not have an up/down adjustment. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE center of the instrument panel. After turning on the ignition, you can choose from High, Off, or Low heat settings. Amber LEDs in the top portion of each switch indicate the level of heat in use. Two LEDs are illuminated for high, one for low, and none for off. Pressing the switch once will select high-level heating. 103 Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. NOTE: The automatic folding rear head restraints will lower as the seat is folded down. 105 To Raise Rear Seat Raise the rear seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage — Rear Seat Armrest (If Equipped) The rear seat may be equipped with a center storage armrest. Armrest Storage Bin Rear Seat Armrest Press the latch and lift the top of the armrest to access the storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Keyless Entry transmitters can also be programmed to recall the same positions when the “Unlock” button is pressed. 107 can accommodate up to four transmitters, each one linked to either of the two memory positions. Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Adjust the brake and accelerator pedals to the desired positions. 10. Insert the ignition key and turn the ignition switch to the ON position. 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter ⬙Yes⬙ or select ⬙Use Factory Settings⬙ from the EVIC and enter ⬙Yes⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under ⬙Electronic Vehicle Information Center (EVIC) — Customer Programmable Features⬙ in Section 4 for more information. Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to ⬙Electronic Vehicle Information Center (EVIC) — Customer Programmable Features⬙ in Section 4 for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Underhood Safety Latch WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Multi-Function Control Lever The multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights and Parking Lights Turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for “Auto” headlight operation (if equipped). Automatic Headlight System — If Equipped Turn the end of the multi-function control lever to the third detent to activate the automatic headlight system. This system performs two functions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE stop. Refer to “Windshield Wipers and Washers” in this section for more information. (See page 120 for more information.) NOTE: When your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “Instrument Panel and Interior Lights” below for setting the instrument panel lights to full daytime intensity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate 1. Pull back on the muti-function control lever to manually deactivate the system (normal operation of high beams). 2. Pull back on the multi-function control lever once again to re-activate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The fog light switch is located in the multifunction control lever. To activate the fog lights, turn on the park/turn lights, low beam headlights, or “Auto” headlights and pull out the end of the multifunction control lever. A light in the instrument cluster shows when the fog lights are on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam Switch Pull the multi-function control lever towards you to switch the headlights to “High” beam. The “High Beam Indicator Light” on the instrument cluster will illuminate. Pull the multi-function control lever a second time to switch the headlights to “Low” beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multi-function control lever toward the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “Speed Sensitive Intermittent Wiper System” in this section. For information on the rear wiper and washer, refer to “Rear Window Features” in this section. (See page 164 for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of five settings to activate this feature. Rain Sensitive Wiper Switch The sensitivity of the system can be adjusted with the multi-function lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system. NOTE: • The rain sensing feature will not operate when the wiper switch is in the LOW or HIGH speed position. • The rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • Use of Rain-X威 or products containing wax or silicone may reduce rain sensor performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. WARNING! Tilting the steering wheel column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator operations at speeds greater than 30 mph (48 km/h) for 3.7L/4.7L engines, 25 mph (40 km/h) for 5.7L engines, and 14 mph (23 km/h) for 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set at a Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory. Pressing the ON·OFF to turn the system OFF or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. If the vehicle speed drops below 30 mph (48 km/h) for 3.7L/4.7L engines, 25 mph (40 km/h) for 5.7L engines, and 14 mph (23 km/h) for 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To help keep your vehicle under control, do not use Speed Control under these conditions: • When it is not possible to keep your vehicle at a set speed. • On slippery roads, such as on snow or ice. • In heavy or varying traffic volume, in traffic that varies in speed, or on winding roads. • Be sure to turn the Speed Control switch to the OFF position when not in use to avoid accidental engagement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the anti-lock brake system (ABS). Applying the brakes very quickly results in the best BAS assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ERM (Electronic Roll Mitigation) This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When ERM determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lift, it applies the appropriate brake and may reduce engine power to lessen the chance that wheel lift will occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP (Electronic Stability Program) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE or gravel conditions and more wheel spin than ESP would normally allow is required to gain traction. To turn ESP on again, momentarily depress the ⬙ESP Control Switch⬙. This will restore the normal “ESP On” mode of operation. ESP Control Switch 135 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE In this mode, ESP and TCS, except for the “limited slip” feature described in the TCS section, are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h) the system returns to “Partial Off” mode, described above. When the vehicle speed drops below 35 mph (56 km/h) the ESP system shuts off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40 mph (64 km/h). At 40 mph (64 km/h), the normal ESP stability function returns but TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP system shuts off. ESP is off at low vehicle speeds in 4WD low range so that it will not interfere with off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h). The ⬙ESP/ TCS Indicator Light⬙ will always be illuminated in 4WD low range when ESP is off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. 3 The sensors can detect obstacles from approximately 11.8 inches (30 cm) up to 59 inches (150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the obstacle is detected at a distance of about 59 inches (150 cm) from the rear fascia, the outermost LEDs of the warning display will be ON with increased brightness. Along with the LED, a half second tone will occur. As the distance of the detected obstacle to the rear fascia decreases, more LEDs are illuminated. When the warning display has the first 5 yellow LEDs ON, the warning display will actuate an intermittent tone for about 10 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message. The Rear Park Assist Switch LED will be ON when the Rear Park Assist System is disabled or defective. The Rear Park Assist Switch LED will be OFF when the system is enabled. Rear Park Assist Switch When the switch is pressed to disable the system, the instrument cluster will display the ⬙PARK ASSIST DISABLED⬙ message.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cleaning the Rear Park Assist System Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. CAUTION! • The Rear Park Assist System is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR CAMERA — IF EQUIPPED Vehicles with a Navigation radio may be equipped with a rear view camera (located on the rear liftgate) that allows you to see an on-screen image (on the navigation radio screen) of the rear of your vehicle whenever the vehicle is put into R (Reverse). WARNING! Drivers must be careful when backing up even when using the rear camera system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Turning the Rear Camera Off 1. To turn the rear camera off, select “Rear Camera” at the Systems Settings screen and press ENTER. Refer to your “Navigation User’s Manual” for detailed operating instructions. 3 2. Select “OFF” at the “Rear Camera” screen. Highlight “DONE” and press ENTER. The rear camera is now disabled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lights also turn on when a front door or rear door is opened. The lights will also turn on when the unlock button on the remote keyless entry transmitter is pressed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a ⬙push/push⬙ design. Push the finger depression on the overhead console to open. Push the finger depression to close.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. The Electronic Vehicle Information Center (EVIC) features a driver-interactive display which includes HomeLink system messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The EVIC display will show “CHANNEL X TRAINING” (where X is Channel 1, 2, or 3). Release both buttons after the EVIC display shows “CHANNEL X TRAINED.” NOTE: If the EVIC display shows “DID NOT TRAIN” repeat steps 2–4. HomeLink Buttons 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. 7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter signals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press and hold the two outer HomeLink buttons and release only when the EVIC display shows “CHANNELS CLEARED” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - Step 2. Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch 153 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER OUTLET To the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. The rear power outlet (if equipped) is located in the left rear cargo area. Rear Power Outlet Front Power Outlet The power outlets are a direct feed from the battery so they receive power whether the ignition is in the ON or OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE All accessories connected to this outlet should be removed or turned off when the vehicle is not in use to protect the battery against discharge. 157 CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS In the center console there are two cup holders for the front seat passengers. cup depression towards the passenger seat, but the top surface will not be flush with the console surface. The rear passengers have access to two cup holders that pull out from the lower center of the rear seat. Front Cup Holders NOTE: The cup holder insert is removable, from the console, for cleaning.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 CARGO AREA FEATURES Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the liftgate is open, pushing on the cargo light lens surface will turn off all interior lamps. Push on the lens surface a second time to restore the interior lights to normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. Cargo Tie-Down Hooks The tie-downs located on cargo area floor should be used to safely secure loads when vehicle is moving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. WARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. 3 Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. wash pump will continue to operate as long as the button is pressed. Upon release, the wipers will cycle three times before returning to the set position. 3. Lift tray over loop(s), and reposition tray. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper. Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity. This vehicle is not equipped with roof rack cross rails as built, unless ordered as optional equipment. Cross rails must be installed prior to carrying loads on the roof rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 CAUTION! WARNING! • To prevent damage to the roof of your vehicle, DO NOT Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack. carry any loads on the roof rack without cross rails installed.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Controls . . . . . . . . . . . . . 172 ▫ Trip Computer . . . . . . . . . . . . . . . . . . . . . . . 193 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 173 䡵 Radio General Information . . . . . . . . . . . . . . . . 197 ▫ Gasoline Engine . . . . . . . . . . . . . . . . . . . . . . 173 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 197 ▫ Diesel Engine . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (VES) Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 ▫ Operating Instructions - Radio Mode . . . . . . . 199 ▫ Operation Instructions - (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 171 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 226 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 230 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 227 䡵 Remote Sound System Controls — If Equipped . . 230 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 227 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 173 INSTRUMENT CLUSTER Gasoline Engine 4
UNDERSTANDING YOUR INSTRUMENT PANEL Diesel Engine
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light The BRAKE warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light stays on longer, it may be an indication that the parking brake has not been released.
UNDERSTANDING YOUR INSTRUMENT PANEL engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles.
UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 9. Security Alarm System Indicator Light — If Equipped This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. If you decide to look under the hood yourself, refer to Section 7 of this manual. Follow the warnings under “Cooling System Pressure Cap.” 14. Electronic Vehicle Information Center Display When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 18. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously.
UNDERSTANDING YOUR INSTRUMENT PANEL is placed in the P (Park) position. The light should turn off. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER — IF EQUIPPED 183 • TURN SIGNAL ON • PERFORM SERVICE • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PROGRAM LIMIT • PROGRAMMING ACTIVE — NEW KEY PROGRAMMED • SERVICE SECURITY KEY • INVALID KEY — TRY ALTERNATE KEY The electronic vehicle information center (EVIC) located in the instrument cluster, when the appropriate conditions exist, will display the following messages and
UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/DOOR OPEN (with graphic) • LIFTGLASS/HOOD OPEN (with graphic) • LIFTGATE/DOORS OPEN (with graphic) • WASHER FLUID LOW (with graphic) • LIFTGLASS OPEN (with graphic) • CHECK GAUGES • HOOD OPEN (with graphic) • AUTO HIGHBEAM ON • HOOD/DOOR OPEN (with graphic) • AUTO HIGHBEAM OFF • HOOD/DOORS OPEN (with graphic) • PARK ASSIST DISABLED • LIFTGATE/HOOD OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • HOOD/GLASS/DOOR OPEN (with graphic) • TRANS
UNDERSTANDING YOUR INSTRUMENT PANEL 185 • CHECK GAS CAP • SERVICE TIRE PRESS SYSTEM • ESP OFF • LEFT FRONT LOW PRESSURE (Premium TPM System Only) • MEMORY #1 POSITIONS SET • MEMORY #2 POSITIONS SET • MEMORY SYSTEM DISABLED — SEATBELT FASTENED (with graphic) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • DRIVER 1 MEMORY • DRIVER 2 MEMORY • PEDAL ADJUST DISABLED — CRUISE CONTROL SET • PEDAL ADJUST DISABLED — SHIFTER IN REVERSE • RIGHT FRONT LOW PRESSURE (Premium TPM System Only) • LEFT REAR LOW PRESS
UNDERSTANDING YOUR INSTRUMENT PANEL Customer Programmable Features Press the MENU button until one of the display choices following appears: Language? When in this display you may select one of three languages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display selects English, Espanol, or Francais. As you continue the displayed information will be shown in the selected language.
UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Linked To Memory? (Available with Memory Seat Only) When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “Unlock” button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory set position using the door mounted switch. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL Illuminated Approach? When this feature is selected the driver can choose, when entering the vehicle, to have the headlamps come on for 30, 60, or 90 seconds, or not come on at all. Pressing the STEP button when in this display will select 30, 60, 90, or OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL Service Interval Gasoline Models — If Equipped When this feature is selected, a service interval between 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile (800 km) increments may be selected. Pressing the STEP button when in this display will select distances between 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile (800 km) increments.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 LINK TO MEMORY is set to YES) when the remote keyless entry transmitter is used to unlock the door. For more information, refer to “Easy Entry/Exit Seat — Driver Memory Seat” in Section 3 of this manual. (See page 110 for more information.) Compass/Temperature/Trip Computer This display provides the outside temperature, one of the eight compass headings to indicate the direction the vehicle is facing, and vehicle trip information.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
UNDERSTANDING YOUR INSTRUMENT PANEL Reset Button Press the RESET button to reset the display you are in. Press and hold the RESET button (for 2 seconds) to reset all of the displays. Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the accumulated ignition ON time since the last reset. Tire Pressure Display — If Equipped Shows the current pressure of all 4 road tires. 195 NOTE: Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures” in Section 5 for additional information. Miles to Service Shows the distance remaining to require service.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass. Refer to Variance Map. To Put Into a Calibration Mode Start the engine and leave the transmission in the P (Park) position. Set the display to “Compass/Temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the C/T button for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the STEP button for 1 second to select the new variance zone and press the RESET button to resume normal operation. RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 199 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player, Satellite Radio, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control. 3. After the hours are adjusted, press the right side Tune / Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune / Audio control. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. turning the TUNE rotary knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information. Press the rotary TUNE control a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Jazz News Nostalgia Oldies Personality Public Rhythm_and_Blues Religious_Music Religious_Talk Rock Soft Soft_Rock Soft_R_&_B Sports Talk Top_40 Weather 203 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET/DIR button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM,12 FM and 12 Satellite (if equipped) stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT Button (CD Mode for CD Audio Play) Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player. Radio display will show ⬙LOADING DISC⬙ when the disc is loading.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder. RW/FF (CD Mode for MP3 Play) Press the FF side of the button to move forward through the MP3 selection.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. 213 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Audio control. 5. To exit, press any button/knob or wait 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will display.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for 5 seconds. Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. RW/FF (Auxiliary Mode) No function. SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM RND/SET Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR press and hold for 3 seconds the TIME button on the unit’s faceplate. The Clock Setup screen appears. 3. To adjust the time zone, Select “Time Zone” and press ENTER. Select the appropriate time zone and press ENTER. 4. To turn daylight savings on or off, select “Daylight Savings” and press ENTER. Select “On” or “Off” and press ENTER. 5. Select DONE to exit from the clock setting mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 3. To decrease the clock by one hour, use the Select Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4. To increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER. Press ENTER again to increase the clock by another minute. 5. To decrease the clock by minutes, use the Select Encoder to highlight the “-“ sign. Press ENTER. Press ENTER again to decrease the clock by another minute. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 1. When you are at an audio screen, quickly press the TIME button on the navigation faceplate. 3. To switch the clock to the small clock, quickly press TIME again. 2. In this example the large clock appears on the screen. 4. To toggle back to the large clock, simply press TIME.
UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The DVD player is mounted in the rear of the center console storage bin, and is concealed by a door that lifts up for access. Refer to your VES™ User’s Manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL The LCD screen is located on the headliner behind the front seats. Remote Control Location Lowering the DVD Screen SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios. System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access with RAQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL appear in the display between each channel change. Press the SCAN button a second time to stop the search. NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-5397474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna To ensure optimum reception on vehicles available with a luggage rack, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons.
UNDERSTANDING YOUR INSTRUMENT PANEL The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center.
UNDERSTANDING YOUR INSTRUMENT PANEL The center button on the left side rocker switch has no function for a single disc CD player. However, when a multiple disc CD player is equipped on the vehicle, the center button will select the next available CD in the player. 5. Store the disc in its case after playing.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Manual Air Conditioning and Heating System — If Equipped The controls for the heating/air conditioning and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. 233 The instrument panel features four dual-vane airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The temperature of air can be selected by rotating the temperature control knob in the center. The coldest temperature setting is on the extreme left and the warmest setting on the extreme right of the rotation. The knob can be positioned at any point on the dial. Mode Control The mode selector (the right rotary knob) can be placed in several positions.
UNDERSTANDING YOUR INSTRUMENT PANEL through vents under the front seats. Some airflow is delivered to defrost while in the floor mode so that comfort can be maintained. Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to partially block airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. Automatic Temperature Control — If Equipped The Infrared Dual-Zone Climate Control System automatically maintains the interior comfort level desired by the driver and passenger.
UNDERSTANDING YOUR INSTRUMENT PANEL LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once the comfort level is selected the system will maintain that level automatically using the heating system.
UNDERSTANDING YOUR INSTRUMENT PANEL debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off until the engine warms up. However, the fan will engage immediately if the defrost mode is selected or if you manually select a blower speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 4
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions.
UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • Panel Air flows through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the “Recirculate” icon button to return to outside air. Some temp./humidity conditions will cause captured interior air to condense on windows and hamper visibility. For this reason, the system will not allow “Recirculate” to be selected while in the defrost or defrost/floor modes.
UNDERSTANDING YOUR INSTRUMENT PANEL When using the air conditioner in extremely heavy traffic in hot weather especially when towing a trailer, additional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed. When stopped in heavy traffic, it may be necessary to shift into N (Neutral) and depress the accelerator slightly for fast idle operation to increase coolant flow and fan speed.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Starting Procedure . . . . . . . . . . . . . . . . . . . . . . 249 ▫ Rocking The Vehicle . . . . . . . . . . . . . . . . . . . 261 ▫ Normal Starting — Gasoline Engines . . . . . . . 249 䡵 Four-Wheel Drive Operation . . . . . . . . . . . . . . . 262 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 249 ▫ Quadra-Trac I威 Operating Instructions/ Precautions — If Equipped . . . . . . . . . . . . . . 262 ▫ Normal Starting — Diesel Engines . . . . . . . . .
STARTING AND OPERATING 䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . . 268 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 278 ▫ When To Use 4WD Low Range — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Driving Through Water . . . . . . . . . . . . . . . . . 268 ▫ Driving In Snow, Mud And Sand . . . . . . . . . . 270 ▫ Hill Climbing . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 247 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 293 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 308 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 308 䡵 Tire Rotation Recommendations . . . . . . . . . . . . 294 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 309 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . . 295 䡵 Flexible Fuel (4.
STARTING AND OPERATING 䡵 Fuel Requirements — Diesel . . . . . . . . . . . . . . . 312 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 325 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 326 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 313 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 330 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURE Start the engine with the selector lever in the N (Neutral) or P (Park) position. Apply the brake before shifting to any driving range. Normal Starting — Gasoline Engines Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, but will automatically disengage itself when the engine is running.
STARTING AND OPERATING If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. depending on engine temperature. When the “Glow Plug Indicator Light” goes out, the engine is ready to start. WARNING! 3. Do not press the accelerator. Turn the ignition key briefly to START position, and release it.
STARTING AND OPERATING Starting and Operating Cautions — Diesel Engines WARNING! NEVER pour fuel or other flammable liquid into the air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Running a cold engine at high speeds during driving or idling may damage engine components. • Before turning off your turbo diesel engine, always allow the engine to return to normal idle speed and 251 run for several seconds.
STARTING AND OPERATING Driving Conditions Stop & Go Stop & Go Highway Speeds City Traffic Highway Speeds Uphill Grade TURBOCHARGER ⬙COOL DOWN⬙ CHART Load Turbocharger Temperature Empty Medium Medium Max. GCWR Max. GCWR Max.
STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with grounded, three wire extension cord. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. The engine block heater cord is located: • 3.7L/4.7L Engine — coiled and strapped to the engine oil dipstick tube. • 5.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
STARTING AND OPERATING 255 gear engagement may be delayed after restarting the engine if the key is not cycled to the LOCK position first. P (Park) This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in P (Park) position.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. On vehicles equipped with 4.7L or 5.7L engines, use of ERS (or Tow/Haul mode) also enables a additional underdrive gear which is not normally used during through-gear accelerations.
STARTING AND OPERATING Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (5th gear for 3.7L engine, 4th and 5th gears for 4.7L and 5.7L engines).
STARTING AND OPERATING 259 In high ambient temperatures with sustained high engine speed and load, an upshift followed shortly thereafter by a downshift may occur. This is a normal part of the overheat protection strategy when operating in the “Tow/Haul” mode. The transmission will downshift from Overdrive to the most desirable gear if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h).
STARTING AND OPERATING Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7L engine) or in direct gear (4.7L and 5.7L engines) until the vehicle is brought to a stop. To reset the transmission, use the following procedure: 1. Stop the vehicle. 2.
STARTING AND OPERATING NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
STARTING AND OPERATING five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle. CAUTION! When “rocking” a stuck vehicle by moving between “First” and R (Reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.
STARTING AND OPERATING 263 percent of engine torque to the rear axle. When speed differences are increased between the front and rear drive shafts, the transfer case can transmit up to 100 percent of available engine torque to the front or rear drive shafts. Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake. The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 265 LOW Indicator Lamp” in the instrument cluster will begin to flash and remain on solid when the shift is complete. Release the T-handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 183 for more information.
STARTING AND OPERATING LOW Indicator Lamp” in the instrument cluster will flash and go out when the shift is complete. Release the T-handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 183 for more information.
STARTING AND OPERATING 267 to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 183 for more information.) Neutral Switch 5. Repeat Steps 1– 4 to shift out of Neutral. NOTE: If shift conditions/interlocks are not met, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer Quadra-Drive II姞 System — If Equipped The optional Quadra-Drive II威 System features three torque transfer couplings.
STARTING AND OPERATING operation is similar. Follow the Quadra-Trac II威 transfer case shifting information, preceding this section, for shifting this system. ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars.
STARTING AND OPERATING CAUTION! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few inches deep will require extra caution to ensure safety and prevent damage to your vehicle.
STARTING AND OPERATING Driving In Snow, Mud and Sand In heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4WD LOW if necessary. Refer to “Four-Wheel Drive Operation” in this section. Do not shift to a lower gear than necessary to maintain headway. Over-revving the engine can spin the wheels and traction will be lost.
STARTING AND OPERATING Remember, never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the front wheels slowly. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. Traction Downhill Shift the transmission into a low gear and the transfer case to 4WD LOW range.
STARTING AND OPERATING • After extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.
STARTING AND OPERATING 273 WARNING! Parking Brake Be sure the parking brake is firmly set when parked and the gear shift lever is in the P (Park) position. When parking on a hill, you should apply the parking brake before placing the gear shift lever in P (Park), otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of P (Park). • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury.
STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING 275 WARNING! WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning.
STARTING AND OPERATING 277 build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action.
STARTING AND OPERATING CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. MULTI DISPLACEMENT SYSTEM (MDS) - 5.7L Engine Only This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions.
STARTING AND OPERATING 279 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 281 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 283 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 287 1. Safety— WARNING! Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion shock.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper cold tire inflation pressure is listed on either the face of the driver’s door, or the driver’s side “B” pillar. 3.
STARTING AND OPERATING 289 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING 291 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 293 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. • Install chains snugly and tighten after 1/2 mile (1 km) of driving. TIRE CHAINS Certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only.
STARTING AND OPERATING 295 Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: The Premium Tire Pressure Monitor System will automatically locate the pressure values displayed in the correct vehicle position following a tire rotation.
STARTING AND OPERATING decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than 3 hours - and in outside ambient temperature. Refer to the “Tires – General Information” in this section for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure.
STARTING AND OPERATING Telltale Light” will turn OFF only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. NOTE: Seasonal temperature changes will affect tire pressure, and the TPM system will monitor the actual tire pressure in the tire. Base System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
STARTING AND OPERATING will automatically update and the “Tire Pressure Monitoring Light” will extinguish once the updated tire pressures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. A low spare tire will not cause the “Tire Pressure Monitoring Telltale Light” to illuminate or the chime to sound.
STARTING AND OPERATING will update automatically, and the “Tire Pressure Monitoring Telltale Light” will be OFF as long as none of the road tires are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle.
STARTING AND OPERATING Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the “Tire Pressure Monitoring Telltale Light.
STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for each condition that it detects.
STARTING AND OPERATING Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic display of the pressure value(s) will stop flashing, and the “Tire Pressure Monitoring Telltale Light” will extinguish once the updated tire pressure(s) have been received.
STARTING AND OPERATING If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “Tire Pressure Monitoring Telltale Light” will no longer flash, the ⬙SERVICE TIRE PRESS. SYSTEM⬙ text message will no longer display, and a pressure value will be displayed instead of dashes.
STARTING AND OPERATING Telltale Light” will be OFF as long as no road tire(s) are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle.
STARTING AND OPERATING 305 Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. The tire pressure sensors are covered under one of the following licenses: • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the “Tire Pressure Monitoring Telltale Light.” United States . . . .
STARTING AND OPERATING 5.7L Engines (If Equipped) The 5.7L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
STARTING AND OPERATING The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
STARTING AND OPERATING It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. MMT is prohibited in Federal and California reformulated gasoline. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: 309 the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. FLEXIBLE FUEL (4.
STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard starting and rough idle following start up even if the above recommendations are followed. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the same. Refer to “Maintenance Procedures” in Section 7 of this manual for the proper quality and viscosity engine oil.
STARTING AND OPERATING Maintenance If you operate the vehicle using E-85 fuel, follow “Maintenance Schedule B.” Refer to Section 8 of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. FUEL REQUIREMENTS — DIESEL Diesel fuels are available from most reputable fuel marketers. We encourage you to use only the best quality fuel with a calculated Cetane Index of 50 or higher.
STARTING AND OPERATING 313 ADDING FUEL CAUTION! DO NOT put gasoline in your diesel vehicle (if equipped). If you accidentally put gasoline in your vehicle, DO NOT start the engine. This will cause damage to the fuel system. Have the fuel system flushed. Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING WARNING! • Never add fuel when the engine is running. • Never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled. VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar.
STARTING AND OPERATING Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability does not necessarily increase the vehicle’s GVWR. Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
STARTING AND OPERATING or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving.
STARTING AND OPERATING Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
STARTING AND OPERATING 321 5 Weight Distributing Hitch System Improper Adjustment of Weight Distributing System
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING 323 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission 3.7L/Automatic Model 4x2 GCWR (Gross Combined Wt. Rating) 8,000 lbs (3 629 kg) 3.7L/Automatic 4x4 8,200 lbs (3 719 kg) 4.7L/Automatic 4x2 8.560 lbs (3 883 kg) 4.7L/Automatic 4x4 8,650 lbs (3 924 kg) 4.7L/Automatic (w/Trailer Tow Group IV) 4.
STARTING AND OPERATING 5.7L/Automatic 5.7L/Automatic (Overland) 5.7L/Automatic 3.0L Diesel/ Automatic 4x2 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 7,400 lbs (3 square meters) 4x2 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 7,395 lbs (3 square meters) 4x4 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 7,200 lbs (3 square meters) 4x4 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 7,200 lbs (3 square meters) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING 325 Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle.
STARTING AND OPERATING Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage.
STARTING AND OPERATING CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
STARTING AND OPERATING 4 - Pin Connector 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”Tow/ Haul” mode (if equipped) or a lower gear range should be selected. NOTE: Using the ”Tow/Haul” mode (if equipped) or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up.
STARTING AND OPERATING − Air Conditioning Turn off temporarily. Towing — Quadra-Trac I (Single-Speed Transfer Case) 4WD Models − Refer to Cooling System Operating information in the Maintenance section of this manual for more information. Recreational towing is not allowed. This model does not have a N (Neutral) position in the transfer case. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing – 2WD Models Recreational towing is allowed ONLY if the driveshaft is removed.
STARTING AND OPERATING Shifting Into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing. CAUTION! indicating shift in progress. Lamp will stop blinking (stay on solid) when Neutral shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 183 for more information.
STARTING AND OPERATING 5. Start engine. 6. Shift transmission into D (Drive). 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into P (Park). 10. Place the ignition key in the OFF position, and remove key. 11. Apply parking brake. 12. Attach vehicle to the tow vehicle with tow bar. 13. Release parking brake.
STARTING AND OPERATING Hold down N (Neutral) “pin” switch (with a pen, etc.) for 4 seconds until the LED lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL” message will no longer be displayed on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. (See page 183 for more information.) 335 5 Neutral Switch 5.
STARTING AND OPERATING NOTE: When shifting out of transfer case N (Neutral), turning the engine OFF may be required to avoid gear clash. CAUTION! Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . . 338 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 342 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 338 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 346 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 339 䡵 Emergency Tow Hooks — If Equipped . . . . . . . . 349 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not to be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES removes this heat. You can also turn the Temperature Control to maximum heat, the Mode Control to floor, and the Fan Control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle.
WHAT TO DO IN EMERGENCIES Jack Location The scissor-type jack and tire changing tools are located in the passenger side compartment behind the second row seat. Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES 341 Spare Tire Removal Fit the jack handle extension over the drive nut. Use the Lug Wrench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. CAUTION! Lowering/Raising Spare Tire The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in P (Park). Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher.
WHAT TO DO IN EMERGENCIES 343 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged.
WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 7.
WHAT TO DO IN EMERGENCIES nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to it’s fully closed position. WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 11.
WHAT TO DO IN EMERGENCIES JUMP STARTING If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other.
WHAT TO DO IN EMERGENCIES 2. Park the booster vehicle within cable reach but without letting the vehicles touch. Set the parking brake on both vehicles, place the transmission in P (Park), and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. TOWING A DISABLED VEHICLE 2WD Models Only Provided the transmission is operable, tow only in N (Neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km) can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L . . . . . . . . . . . . . . . 354 䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 361 䡵 Engine Compartment – 4.7L . . . . . . . . . . . . . . . 355 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . . 362 䡵 Engine Compartment – 5.7L . . . . . . . . . . . . . . . 356 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 362 䡵 Engine Compartment – 3.0L Diesel . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 370 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 386 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 371 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 372 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 374 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 353 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 404 䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . . 408 ▫ Rear Tail, Stop, Turn Signal, And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 ▫ Center High Mounted Stop Light (CHMSL) . . . 406 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 䡵 Fluids And Capacities . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 3.
MAINTAINING YOUR VEHICLE 355 ENGINE COMPARTMENT – 4.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.
MAINTAINING YOUR VEHICLE 357 ENGINE COMPARTMENT – 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE manual). Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. This message may be temporarily overridden by pressing either the C/T, STEP, or MENU buttons. However, after one minute of no customer interaction, the EVIC will display again the “CHECK GASCAP” message. The message will remain displayed until the vehicle diagnostic system can retest the fuel system.
MAINTAINING YOUR VEHICLE replacement. If the OBD system should be determined not ready for the I/M test, your vehicle may fail the test. Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3.
MAINTAINING YOUR VEHICLE during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance. Damage or failures caused by the use of non-Mopar威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty.
MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Extensive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
MAINTAINING YOUR VEHICLE Material Standard MS-6395. Use Mopar威 or an equivalent oil meeting the specification MS-6395. Engine Oil Selection - Diesel Engines For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS-11106 or Mercedes Benz MB 229.
MAINTAINING YOUR VEHICLE For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. Engine Oil Viscosity (3.0L Diesel Engine) CAUTION! Your vehicle is equipped with an advanced technology Diesel Engine and an emission device designed to limit Diesel Particulate Emissions from being released into the atmosphere.
MAINTAINING YOUR VEHICLE indiscriminately discarded, can present a problem to the environment. Contact your local authorized dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement.
MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New spark plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the “Vehicle Emission Control Information” label in the engine compartment for spark plug information. Spark Plug Wires The spark plug wires should be kept clean and properly connected. Terminals should be fully seated.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps.
MAINTAINING YOUR VEHICLE 371 CAUTION! To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
MAINTAINING YOUR VEHICLE 373 CAUTION! WARNING! Do not use Automatic Transmission Fluid (ATF) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid.
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and operate the system for a few seconds to flush out the residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. Cooling System WARNING! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator.
MAINTAINING YOUR VEHICLE for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of antifreeze/coolant other than the specified HOAT antifreeze/coolant may result in decreased corrosion protection and engine damage. If a nonHOAT antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coolant as soon as possible. Do not use plain water alone or alcohol base antifreeze/coolant products.
MAINTAINING YOUR VEHICLE Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol-based antifreeze/coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze/ coolant needs to be added, contents of coolant recovery bottle must also be protected against freezing.
MAINTAINING YOUR VEHICLE Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE 383 Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold.
MAINTAINING YOUR VEHICLE Brake Master Cylinder — Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service, or immediately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots.
MAINTAINING YOUR VEHICLE CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Front/Rear Axle Fluid Front Axle Fluid Level Check Lubricant should be to the bottom of the oil fill hole. Rear Axle Fluid Level Check Lubricant should be 1/2” (1 cm) below the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! When installing plugs, do not overtighten. You could damage them and cause them to leak. Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3.
MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated.
MAINTAINING YOUR VEHICLE Service Manual. Also check for accumulations of vegetation or brush that could become a fire hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. CAUTION! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body components, all driveline joints and steering linkage more often than in normal service to prevent excessive wear.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar威 Super Kleen Bug and Tar Remover to remove. • Use Mopar威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag.
MAINTAINING YOUR VEHICLE Cavity 3 4 5 6 7 8 Fuse Panel Location Cavity 1 2 Cartridge Fuse Mini Fuse 30 Amp Green 15 Amp Blue Description Audio Amp (B+) Sunroof (B+) 9 Cartridge Fuse Mini Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red Spare (B+) 20 Amp Yellow 15 Amp Blue 20 Amp Yellow Description Htd Mirror (EBL) Rr Pwr Out (B+) Rr HVAC (R/O) (XK Only) Door Locks (B+) Steer Col Lock (B+) (ELV) Pwr Outlet (B+)
MAINTAINING YOUR VEHICLE Cavity 10 11 12 13 Cartridge Fuse Mini Fuse 10 Amp Red Description Final Drive Control Module (FDCM), Heater Ventilation, Air Conditioning (HVAC), Switch Bank, Transfer Case Switch, O/H, Heater Ventilation, Air Conditioning (HVAC) Relay, Rear Park Assist Spare (B+) 10 Amp Door Mods, Mem.
MAINTAINING YOUR VEHICLE Cavity 21 22 24 25 Cartridge Fuse Mini Fuse Spare (Acc Delay) 15 Amp Blue 10 Amp Red 10 Amp Red Description Underhood Fuses (Power Distribution Center) Rear Wiper (B+) Power Distribution Center (PDC) Relays, Final Drive Control Module (FDCM), Front Control Module (FCM) (R/S), A580 (R/S) Shifter Assy (BTSI), Trans.
MAINTAINING YOUR VEHICLE Cavity 2 3 4 5 6 7 8 9 Cartridge Fuse 30 Amp Pink 30 Amp Pink 30 Amp Pink 50 Amp Red 50 Amp Red 30 Amp Pink 40 Amp Green 40 Amp Green Mini Fuse Description Cavity Power Outlets 10 Rr Wiper/Ign R/O 11 ABS Pump 12 Cabin Htr 1 (Diesel Only) Auto Shut Down (ASD) Rr HVAC (XK Only) 13 15 Acc Delay/Seats 16 Pwr Liftgate (XK Only) 17 14 Cartridge Fuse 40 Amp Green 30 Amp Pink 40 Amp Green 40 Amp Green 50 Amp Red 50 Amp Red Mini Fuse 397 Description Starter/Junction Bl
MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 24 25 Cartridge Fuse Mini Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 30 Amp Green 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description EATX/AC Clutch Cavity 26 Cartridge Fuse Mini Fuse 15 Amp Blue Ign Sw PCM Batt (Gasoline Only) ABS Valves T-Tow (BUX) Final Drive Control Module (FDCM) Fuel Pump Final Drive Control Module (FDCM) 27 28 15 Amp Blue 25 Amp Natural Description Powertrain Control Module (PCM) Auto Shut Down (ASD)
MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Cavity 9 10 12 13 14 Integrated Power Module Cavity 8 Cartridge Fuse Mini Fuse 10 Amp Red Description Lt Park Lamps 15 16 17 Cartridge Fuse Mini Fuse 10 Amp Red 10 Amp Red 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 399 Description Trailer-Tow Park Lamps Rt Park Lamps Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal Ft Fog Lamps Horn Rear Wiper 7
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 18 19 20 21 22 30 Amp Pink 23 50 Amp Red 27 28 Mini Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow Description Front Control Module (FCM) Batt #1 Lt Trailer-Tow Stop/ Turn Front Control Module (FCM) Batt #3 Rt Trailer-Tow Stop/ Turn Final Drive Control Module (FDCM) MOD Radiator Fan Ignition Off Draw (IOD) #1 Ignition Off Draw (IOD) #2 Cavity 29 30 Cartridge Fuse Mini Fuse 10 Amp Red 10 Amp Red Descript
MAINTAINING YOUR VEHICLE in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb Type Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Grab Handle Light . . . . . . . . . . . . . . . . L002825W5W Overhead Console Reading Lights . . . . . . . . . . VT4976 Rear Cargo Light . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2BULB REPLACEMENT Head Light 1. Open the hood. 2. Remove the headlamp cover. 4. Disconnect the electrical connector and replace the bulb. CAUTION! 3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
MAINTAINING YOUR VEHICLE Front Turn Signal 1. Open the hood. 403 3. Turn the turn signal bulb 1/4 turn counter clockwise to remove from housing. 2. Remove the headlamp cover. 7 4. Disconnect the electrical connector and replace the bulb.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Light Rear Tail, Stop, Turn Signal, and Back-Up Lights 1.
MAINTAINING YOUR VEHICLE 405 3. Squeeze the socket assembly tabs to remove it from the housing. 7 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly.
MAINTAINING YOUR VEHICLE Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
MAINTAINING YOUR VEHICLE 407 FLUIDS AND CAPACITIES Fuel (Approximate) 3.7/4.7/5.7L Gasoline Engines 3.0L Diesel Engine Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 4.7 Liter Engine (SAE 5W-20, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) 3.0 Liter Diesel Engine (SAE 5W-30 Synthetic, API Certified) Cooling System * 3.7 Liter Engine (Mopar威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula) 4.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395. Use API Certified SAE 5W-30 Synthetic Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-11106 or Mercedes Benz MB 229.
MAINTAINING YOUR VEHICLE 409 Chassis Component Automatic Transmission Transfer Case (3.7L Engine Only) Transfer Case Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid Mopar威 ATF+4 Automatic Transmission Fluid Mopar威 NV 247/245 Transfer Case Lubricant Mopar威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance . . . . . . . . 412 䡵 Maintenance Schedules — Diesel Engines . . . . . 433 M A I N T E N A N C E S 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 412 ▫ Schedule “B” — Diesel Engines . . . . . . . . . . . 436 C ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 441 E ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 412 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service) • Off-road or desert driving NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” NOTE: If ANY of these apply to you, change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance recommendations in “Maintenance Schedule B.
M A I N T E N A N C E S C H E D U L E S 8 414 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect brake hoses.
SCHEDULE “B” Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
M 416 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Drain and refill the front and rear axles. Inspect the brake linings. Drain the transfer case and refill.
M 418 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Drain and refill the front and rear axles. Inspect the brake linings.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axles.
M 420 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary.* Drain and refill the transfer case fluid. Inspect the brake linings. Drain and refill the front and rear axle fluid.
M 422 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Flush and replace the engine coolant/anti-freeze, if not done at 60 months.
SCHEDULE “B” 423 M Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter, if not replaced at X X X X X 3 months. Rotate the tires. X X X Check spare tire for proper pressure and correct stowage. X X X Inspect the engine air cleaner filter, replace if necessary. X Inspect the PCV Valve, replace if necessary.〫 X Replace the spark plugs. X Inspect the engine accessory drive belt, replace if necessary.
M 424 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate the tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid.
SCHEDULE “B” Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Drain and refill the transfer case fluid.
M A I N T E N A N C E S C H E D U L E S 8 426 SCHEDULE “B” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 〫 This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. * This maintenance is not required if the belt was previously replaced.
SCHEDULE “A” 427 M Schedule “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Replace the spark plugs. Inspect the brake linings. Drain the transfer case and refill.
M 428 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Inspect the brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary. Flush and replace the engine coolant/anti-freeze. Inspect the brake linings. Drain the transfer case and refill.
M 430 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not done at 102,000 miles (170 000 km).
M 432 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change the engine oil and engine oil filter. N C Rotate the tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the engine accessory drive belt, replace if necessary.* Inspect the brake linings.
SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 〫 This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. * This maintenance is not required if the belt was previously replaced. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment.
M A I N T E N A N C E 434 SCHEDULE “A” NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Schedule “B.” • Check the windshield washer solvent, add as required. Use the schedule that best describes your driving condiS tions.
SCHEDULE “A” At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect brake hoses. • Check the engine coolant/anti-freeze level, hoses, and clamps. 435 M A • Inspect engine accessory drive belts. Replace as neces- I N sary. T E • Inspect for the presence of water in the fuel filter/ N A water separator unit.
M A I N T E N A N C E S C H E D U L E S 8 436 SCHEDULE “B” — DIESEL ENGINES Schedule “B” — Diesel Engines Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing.
SCHEDULE “B” — DIESEL ENGINES Miles (Kilometers) Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air filter element. Replace as necessary. Replace the engine air filter element. Replace the fuel filter/water separator unit. Inspect the brake linings. Drain the transfer case and refill. Drain and refill the front and rear axles.
M 438 SCHEDULE “B” — DIESEL ENGINES A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Rotate the tires. N C Check spare tire for proper pressure and correct E stowage. S C H E D U L E S 8 Inspect the engine air filter element. Replace as necessary. Replace the engine air filter element. Replace the fuel filter/water separator unit. Replace the engine accessory drive belt. Inspect the brake linings. Drain and refill the front and rear axles.
SCHEDULE “B” — DIESEL ENGINES Miles (Kilometers) Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air filter element. Replace as necessary. Replace the engine air filter element. Replace the engine accessory drive belt. Replace the fuel filter/water separator unit. Flush and replace the engine coolant/antifreeze. Inspect the brake linings. Drain the transfer case and refill. Drain and refill the front and rear axles.
M A I N T E N A N C E S C H E D U L E S 8 440 SCHEDULE “B” — DIESEL ENGINES 〫 Applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † The replacement of such component is requested when there is superficial wear, bearing clearance, or evident grease leak. Inspection and service should be performed anytime a malfunction is observed or suspected. Retain all receipts.
SCHEDULE “A” 441 M Schedule “A” Miles (Kilometers) Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air filter element. Replace as necessary. Replace the engine air filter element. Replace the fuel filter/water separator unit. Inspect the brake linings. Drain the transfer case and refill.
M 442 SCHEDULE “A” A I N Miles T (Kilometers) E N Change the engine oil and engine oil filter. A Rotate the tires. N C Check spare tire for proper pressure and correct stowage. E Inspect the engine air filter element. Replace as necesS C H E D U L E S 8 sary. Replace the engine air filter element. Replace the fuel filter/water separator unit. Flush and replace the engine coolant/anti-freeze. Replace the engine accessory drive belt. Inspect the brake linings. Drain the transfer case and refill.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 444 ▫ Prepare For The Appointment . . . . . . . . . . . . 444 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 444 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 447 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 447 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 448 ▫ Be Reasonable With Requests .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 176,274 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 165 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 124 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 367 Air Conditioner Maintenance . . . . . . . . . . . . . . . 371 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 235 Air Conditioning, Operating Tips . . . . . . .
INDEX Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Auxiliary Electrical Outlet (Power Outlet) . . . . . . 156 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 156 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 346 Keyless Transmitter Replacement (RKE) . . . . . . . 23 Saving Feature (Protection) . . . . . . . . . . . . . . . 113 Belts, Drive . . . . . . . . . . . . . . . . . . . .
INDEX Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 163 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 161 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . . 368 Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 147 CD (Compact Disc) Player . . . . . . . . . . . . . . . 199,213 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Customer Assistance . . . . . . . . . . . . . . . . . . . . . 444 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 52 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 116 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 165 Defroster, Windshield . . .
INDEX Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . . 180,183 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 261 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 338 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 346 Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Emission Control System Maintenance . . . . . .
INDEX Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 367 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 365 Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 338 Turn Signal . . . . . . . . . . . . . . . . . . . . .
INDEX Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Materials Added . . . . . . . . . . . . . . . . . . . . . . . 308 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 305,306 Requirements . . . . . . . . . . . . . . . . . . . . . . 312,407 System Hoses . . . . . . . . . . . . . . . . . . . . . . . . . 382 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 407 Fuel, Flexible . . . . . . . .
INDEX Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 253 High Beam Indicator . . . . . . . . . . . . . . . . . . . . . 175 High Beam/Low Beam Select (Dimmer) Switch . . 118 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 322 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Key, Replacement . . . . . Key, Sentry (Immobilizer) Key-In Reminder . . . . . . Keyless Entry System . . . Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 15 15 19 14 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 35 LATCH (Lower Anchors and Tether for CHildren) . . . . . . . . . .
INDEX Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 114 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 Headlights On With Wipers . . . . . . . . . . . . . . . 114 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 175 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 19 Instrument Cluster . . . . . . . . . . . . . . . . . . . 114,116 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . 116,118 Lights On Reminder . . . . . . . . . . . . .
INDEX Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 58,60 . 374 . 166 . 101 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 370 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 362 Maintenance Schedule . . . . . . . . . . . . . . . . .
INDEX New Vehicle Break-In Period . . . . . . . . . . . . . . . . 64 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 34 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . 305,306 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 180,181 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Off-Pavement Driving (Off-Road) . . . . . . . . . . 268,388 Off-Road Driving (Off-Pavement) . . . . . . . . . . 268,388 Oil, Engine . . . . . . . . . . . . . . . . . .
INDEX Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 64 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Phone, Hands-Free (UConnect™) . . . . . . . . . . . . . 77 Placard, Tire and Loading Information . . . . . . . . . 283 Polishing and Waxing . . . . . . . . . . . . . . . . . . . . . 390 Power Distribution Center (Fuses) . . . . . . . . . . . . . . . 396 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Mirrors . . . . . . . . . . . . . . .
INDEX Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 164 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 72 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 100 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 52 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 332 Shifting into Transfer Case Neutral (N) . . . . . . . 333 Shifting out of Transfer Case Neutral (N) . . . . . 334 Reformulated Gasoline . . . . . . . . . . . . . . . .
INDEX Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 65,393 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . . 40 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Cleaning . . . . .
INDEX Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363,364 Speed Control (Cruise Control) . . . . . . . . . . . . . . 126 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 Automatic Transmission . . . . . . . . . . . . . . . . . 249 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . 253 Engine Block Heater . . . . . . . . . . . . . . . . . . . . 253 Engine Fails to Start . . . . . .
INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66,287,449 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 288 Alignment and Balance . . . . . . . . . . . . . . . . . . 293 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 General Information . . . . . . . . . . . . . . . . . . . . 287 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Inflation Pressures . . .
INDEX Trailer and Tongue Weight . . . . . . . . . . . . . . . . 325 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 323 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 323 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . 254,386 Maintenance . .
INDEX Washers, Windshield . . . . . . . . . . . . . . . . . . 120,374 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 390 Waxing and Polishing . . . . . . . . . . . . . . . . . . . . . 390 Wheel Alignment and Balance . . . . . . . . . . . . . . . 293 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 391 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 391 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . . . 344 Wind Buffeting . . . . . . . . . . . . . .
NOTES
NOTES
