TABLE OF CONTENTS SECTION PAGE .............................................................3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .365 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8 m Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . . 5 m Vehicle Identification Number . . . . . . . . . . . . . . . 8 m How To Use This Manual . . . . . . . . . . . . . . . . . . 6 m Vehicle Modifications/Alterations . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and handling will have a different feel from what drivers experience with other vehicles, so take time to become familiar with your vehicle. The two-wheel drive utility vehicle was designed for on-road use only.
INTRODUCTION NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopart parts, and is interested in your satisfaction. ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.
INTRODUCTION Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.
INTRODUCTION 7 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .14 m Security Alarm System — If Equipped . . . . . . . . .20 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . .14 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .20 ▫ FOB With Integrated Key (FOBIK) . . . . . . . . . .15 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .21 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .16 m Illuminated Entry .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters . . . . . . . .25 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .36 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .25 m Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .38 ▫ General Information . . . . . . . . . . . . . . . . . . . .26 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .39 m Remote Starting System — If Equipped . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .60 m Engine Break-In Recommendations . . . . . . . . . . .69 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .70 13 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three of which are detented and one spring-loaded.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Fob with Integrated Key (FOBIK) The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the Fob. 2 The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. You can keep the valet key with you when valet parking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Key Removal Place the selector lever in “P” (Park). Turn the key to the LOCK position, and remove the key. NOTE: • If you try to remove the key before you place the selector lever in “P” (Park), it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE flash after the bulb check, it indicates that someone used an invalid Fob to start the engine. Either of these conditions will result in the engine being shut off after two (2) seconds. If the Vehicle Security Alarm Indicator Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE location. This number is required for dealer replacement of Fobs. Duplication of Fobs may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank Fob to the vehicle electronics. A blank Fob is one, which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle Fobs with you to the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your dealer to have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the door lock plunger located on the inside of the doors or with the driver’s door key lock cylinder, will not set the alarm. To Disarm the System To disarm the system, use the remote keyless entry transmitter. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Inserting the Fob with Integrated Key into the ignition switch disables all buttons on that transmitter; however, the buttons on the remaining transmitters will continue to work. Shifting the vehicle out of “P” (Park) disables all transmitter buttons for all Fobs. To Unlock the Doors Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Release the Liftgate Flipper Glass Press the “Flipper Glass/Trunk Release” button on the transmitter two times to release the flipper glass. WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Refer to SENTRY KEY “Customer Key (Fob) Programming.” 2 If you do not have a programmed transmitter, contact your dealer for details. Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/ perchlorate NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the “Unlock” button on the key fob. After the vehicle is unlocked, you have 15 minutes to enter the vehicle, insert the key into the ignition, and move it to the RUN position. Otherwise, the engine will cancel remote start and automatically turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Theft Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the RUN position, then back to LOCK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks The power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors. 29 If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit Feature — Only Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in P (Park) or N (Neutral). Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 of this manual or see your authorized dealer. WARNING! Avoid trapping anyone in the vehicle in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. 2 Power Window Switches The power window switches remain active for up to 10 minutes after the ignition switch has been turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. 2 Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up: Pull the window switch up and close the window completely, then pull and hold the switch for 1 second.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. 35 WARNING! To avoid injury stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate. Once the liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate. Light pressure anywhere along these strips will cause the liftgate to return to the open position. • The power liftgate must be in the full open position for any of the buttons to operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Gas props support the liftgate in the open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 43 6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best. As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. The manufacturer does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the OFF position, and buckle the driver’s seat belt. 2. Turn the ignition key to the ACCESSORY/RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. 2 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. seat as far back as possible, and use the proper child restraint. See “Child Restraint” in this section. 1. Children 12 years and under should always ride buckled up in a rear seat. You should read the instructions provided with your child restraint to make sure that you are using it properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The Occupant Restraint Control (ORC) Module determines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direction provided by the ORC. The ORC will detect roll overs, not rear impacts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates are possible, based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position everyone for the best interaction with the front airbag. If A Deployment Occurs The airbag system is designed to deploy when the Occupant Restraint Control (ORC) Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and seat belt retractor assembly, replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! 57 NOTE: Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/ perchlorate • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to 5-seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or neardeployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status • Traction/stability control status • Tire pressure monitoring system status Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt-positioning booster seat. The child and beltpositioning booster seat are held in the vehicle by the lap/shoulder belt. Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. Tether Strap Mounting Latch Anchorages In addition, there are tether strap anchorages behind each rear outboard seating position located on the back of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has an automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to “Automatic Locking Mode” earlier in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For the outboard seating positions, route the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires (including spare) for proper pressure. Lights Have someone observe the operation of all exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .78 ▫ Automatic Dimming Mirror — If Equipped . . . .78 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .79 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .80 ▫ Driver’s And Front Passenger Outside Automatic Dimming Mirror — If Equipped . . . .80 ▫ Power Remote Control Outside Mirrors — If Equipped . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . 100 ▫ 50/50 Third Row Folding Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ General Information . . . . . . . . . . . . . . . . . . . 108 m Driver Memory Seat — If Equipped . . . . . . . . . 118 m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 ▫ Automatic Headlight System — If Equipped . . 126 ▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 ▫ SmartBeams — If Equipped . . . . . . . . . . . . . . 126 ▫ Speed Sensitive Intermittent Wiper System . . . 132 ▫ Instrument Panel And Interior Lights . . . . . . . 127 ▫ Rain Sensing Wipers—If Equipped . . . . . . . . . 133 ▫ Daytime Running Lights — If Equipped . . . . . 128 m Tilt/Telescoping Steering Column . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE m Electronic Brake Control System . . . . . . . . . . . . 139 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . . 154 ▫ ABS (Anti-Lock Brake System) . . . . . . . . . . . . 139 ▫ Rear Park Assist Warning Display . . . . . . . . . 154 ▫ TCS (Traction Control System) . . . . . . . . . . . . 140 ▫ Enable/Disable The Rear Park Assist System . . 156 ▫ BAS (Brake Assist System) . . . . . . . . . . . . . . . 141 ▫ Service The Rear Park Assist System . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Reprogramming a Single HomeLinkt Button . . 164 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 168 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 m Command-View™ Skylights — If Equipped . . . . 168 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 164 m Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 169 ▫ General Information . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. After selecting a mirror move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this section for details. Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. 3 Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED NOTE: The sales code RER radio contains an integrated Hands-Free Communication (UConnect™) system. Refer to your “Navigation User’s Manual” for UConnect™ system operating instructions for this radio. UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phone book accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as 9CELL9 or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the “Phone” button and follow audible prompts for directions. All UConnect™ system sessions begin with a press of the “Phone” button on the radio control head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Call by Saying a Name Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin. NOTE: Adding names to phone book is recommended when vehicle is not in motion. • After the 9Ready9 prompt and the following beep, say “Call.9 • Press the “Phone” button to begin. • System will prompt you to say the name of the person you want call. • After the 9Ready9 prompt and the following beep, say 9Phonebook New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phone book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect™ system will allow you to enter up to 32 names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnect™ Phonebook NOTE: Editing names in the phone book is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Phonebook Edit.9 • You will then be asked for the name of the phone book entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from the list, press the 9Voice Recognition9 button while the UConnect™ system is playing the desired entry and say 9Delete.9 • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, pager, or all. Say the designation you wish to delete. • After confirmation, the phone book entries will be deleted. • Note that only the phone book in the current language is deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • The UConnect™ system will then prompt you as to the number designation you wish to call. call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.9 Place/Retrieve a Call from Hold To put a call on hold, press the 8Phone’ button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep. Redial • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Redial.9 • The UConnect™ system will call the last number that was dialed on your cellular phone. NOTE: This may not be the last number dialed from the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ System Features Language Selection To change the language that the UConnect™ system is using, • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. Please refer to the 24-Hour “Towing Assistance” coverage details in the Warranty information booklet and on the 24–Hour Towing Assistance Card.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can use your UConnect™ system to access a voicemail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE a{,9 you could press the “Voice Recognition” button and say 9Pair a Phone9 to select that option without having to listen to the rest of the voice prompt. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect™ system will not repeat a phone number before you dial it). • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Confirmations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-Mute (Mute Off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: • Press the “Voice Recognition” button. • Following the beep, say 9Mute.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 List Paired Cellular Phone Names • Press the “Phone” button to begin. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Select Phone9 and follow the prompts. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing.” • When prompted, say 9List Phones.9 • The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • At the next prompt, say 9Delete9 and follow the prompts. From outside the UConnect™ mode (e.g. from radio mode) • You can also press the “Voice Recognition” button anytime while the list is being played, and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) • fully closed windows, • For best performance, adjust the rear view mirror to provide at least 1⁄2 inch (1 cm) gap between the overhead console (if equipped) and the mirror. • dry weather condition. 101 • Always wait for the beep before speaking. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be spoken 9eight-zero-zero.9 • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book 107 Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect™ Tutorial try again voice training work yes 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. SEATS Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment bar.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8 - Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 center of the instrument panel. After turning on the ignition, you can choose from High, Low, or Off heat settings. Amber LEDs on the side of each switch indicate the level of heat in use. Two LEDs are illuminated for high, one for low, and none for off. Pressing the switch once will select high-level heating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 40/20/40 Second Row Folding Seat Fold and Tumble Second Row Seat The left, center, or right side of the second row seat can be lowered to allow for extended cargo space, and still maintain some rear seating room. 3 1. Pull up on the seatback lever located on the outboard side of the seat. NOTE: Also, pulling upward on this handle allows the outboard seating positions to be reclined. Seatback Release Lever 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury. Fold and Tumble Seat NOTE: If sitting in the third row seat, pull rearward on the release strap located at the rear of the seat and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Folding Middle Seatback (Second Row Seat) 1. Pull the release strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Lower the center seatback. Center Seat Armrest (Second Row Seat) — If Equipped The second row center seat may be equipped with a armrest. Pull strap to lower armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 50/50 Third Row Folding Seat — If Equipped To Lower Rear Seat Either side of the third row seat can be lowered to allow for extended cargo space, and still maintain some rear seating room. 3 1. Open the tailgate. 2. Push the seatback release handle (toward rear of vehicle), and lower the seatback using the pull strap. Seatback Release Handle 3. Close the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat WARNING! 1. Open the tailgate. 2. Detach pull strap from back of seat, and pull seatback upward until it locks into place. Reattach strap. Pull Strap 3. Close the tailgate. The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position. Driver Memory Switches Your vehicle may have been delivered with two Remote Keyless Entry transmitters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. Turn the ignition switch to the OFF position and remove the key. 7. Press and release the SET (S) button located on the driver’s door. 8. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door. The next step must be performed within 5 seconds if you desire to also use a Remote Keyless Entry transmitter to recall memory positions. 9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmitter linked to memory position 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under 9Electronic Vehicle Information Center (EVIC) — Customer Programmable Features9 in Section 4 for more information. Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to 9Electronic Vehicle Information Center (EVIC) — Customer Programmable Features9 in Section 4 for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature—Exterior/Interior Lights If the multi-function control lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the OFF position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition is turned ON or when the headlight switch is turned to another position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlight System — If Equipped Turn the end of the multi-function control lever to the third detent to activate the automatic headlight system. approximately four minutes after the wipers completely stop. Refer to “Windshield Wipers and Washers” in this section for more information. This system performs two functions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the windshield or SmartBeam mirror is replaced, the SmartBeam mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To Activate 1. Select “Auto Headlamp Low/High Beams? — Low/ High Beam.” Refer to “EVIC — Customer Programmable Features” in Section 4 of this manual. 2. Turn the end of the multi-function control lever to the A (Auto) headlight position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the second detent above the dimmer range turns the interior lights on. Rotating the control to the “Off” (extreme bottom) position disables all the interior lights, even when the doors and liftgate are open. While in the “Off” position the instrument panel lighting is at the lowest light level and may not be suitable for night driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Proper aim and adjustments of the front fog lights should be made to prevent excessive glare for other drivers. Turn Signals Move the multi-function control lever up or down and the arrows on each side of the instrument cluster will flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lighting consists of courtesy lights mounted below the instrument panel, an overhead console light assembly which contains both driver and passenger reading lights, reading lights located above the rear doors, and a rear cargo light. Opening a door or turning the center of the multi-function control lever to the extreme up position will activate all interior courtesy lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “Speed Sensitive Intermittent Wiper System” in this section. For information on the rear wiper and washer refer to “Rear Window Features” in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of five settings to activate this feature. The sensitivity of the system can be adjusted with the multi-function lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Transmission in N (Neutral) Position — When the ignition is ON, and the transmission is in the N (Neutral) position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the N (Neutral) position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward the driver to provide improved position with the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Leaving the Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. Electronic Speed Control Switch To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake or clutch pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed To resume a previously set speed, push the “RESUME ACCEL” lever up and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills The automatic transmission may downshift on hills to maintain the vehicle set speed. NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in Section 5 of this manual for more information about ABS. WARNING! ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the anti-lock brake system (ABS). Applying the brakes very quickly results in the best BAS assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ERM (Electronic Roll Mitigation) This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When ERM determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lift, it then applies the brake of the appropriate wheel and may also reduce engine power to lessen the chance that wheel lift will occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP (Electronic Stability Program) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE or gravel conditions and more wheel spin than ESP would normally allow is required to gain traction. To turn ESP on again, momentarily depress the 9ESP OFF” switch. This will restore the normal “ESP On” mode of operation. ESP OFF Switch 145 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE In this mode, ESP and TCS, except for the “limited slip” feature described in the TCS section, are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h) the system returns to “Partial Off” mode, described above. When the vehicle speed drops below 35 mph (56 km/h) the ESP system shuts off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE a speed of 40 mph (64 km/h). At 40 mph (64 km/h), the normal ESP stability function returns but TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP system shuts off. ESP is deactivated at low vehicle speeds in 4WD low range so that it will not interfere with off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE swaying. Always use caution when towing a trailer and follow the tongue weight recommendations. Refer to “Trailer Towing” in Section 5 of this manual for more information on towing a trailer with your vehicle. When TSC is functioning, the “ESP/TCS Indicator Light” will flash, the engine power may be reduced and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HSA Activation Criteria The following criteria must be met in order for HSA to activate: • Vehicle must be stopped. • Vehicle must be on a 8% grade or greater hill. • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in R (Reverse) gear). HSA will work in R (Reverse) and all forward gears when the activation criteria have been met.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 and will only activate when the vehicle is descending a hill. It will usually not activate on level ground. The HDC speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the transmission gear selected. • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd = 4 mph (6 km/h) • 4th = 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HDC also has the capability to sense rough terrain, and will automatically adjust to a slightly slower set speed (about.3 mph (.5 km/h) than normal. HDC operation can be overridden with brake application to slow the vehicle down below the HDC control speed. Conversely, if more speed is desired during HDC control, the accelerator pedal will increase vehicle speed in the usual manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approximately 11.8 inches (30 cm) up to 59 inches (150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 The system dimly illuminates the two outer most yellow LED’s when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in. (150 cm) 51 in. (130 cm) 45 in. (115 cm) 31.5 in. (80 cm) 39 in. (100 cm) 25.5 in. (65 cm) 33.5 in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone. Enable/Disable the Rear Park Assist System The Rear Park Assist System can be enabled and disabled with a switch located on the upper switch bank of the instrument panel. When the switch is pressed to disable the system, the instrument cluster will display the 9PARK ASSIST DISABLED9 message.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cleaning the Rear Park Assist System Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Select “ON” at the “Rear Camera” screen. Highlight “DONE” and press ENTER. The rear camera is now enabled. 3. When the vehicle is shifted into R (Reverse), the CAUTION screen will appear, followed by an image of the rear of the vehicle. OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains an optional universal garage door opener (HomeLinkt), storage for sunglasses, and optional power sunroof switches. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off of your vehicle’s battery. NOTE: HomeLinkt is disabled when the Vehicle Security Alarm is active. 159 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Then release both the HomeLinkt and hand-held transmitter buttons. If the EVIC display still states “CHANNEL # TRAINING” repeat Step 3. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open & close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLinkt to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLinkT Button To re-program a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLinkt button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with PROGRAMMING HOMELINK Step #2 and follow all remaining steps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console. 1. This device may not cause harmful interference 3 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: Hold onto shade handle until shade is completely open or closed. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 POWER OUTLET Front Power Outlet To the left and right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. 3 Rear Power Outlet — If Equipped The rear power outlet (if equipped) is located in the left rear cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off. 171 inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. NOTE: Due to built in overload protection, the inverter will shut down if the power rating is exceeded.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS Front Cup Holders In the center console, there are two cup holders for the front seat passengers. NOTE: The cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console surface. Cup Holders (Second Row Seat) The second row seat has two cup holders in the center armrest. Lower the center armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Cup Holders (Third Row Seat) The third row seat passengers have cup holders on the left and right rear trim panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: Rear Storage Cover NOTE: The cargo load floor latches should not be used as cargo tie-downs. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 4. Pull up on loop(s) and twist 90 degrees, so they are perpendicular (straight up) to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray. 5. Push loop(s) back down, so they are parallel to the top of the tray.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the wiper. Rotating the center of the switch all the way up or down will turn on the wash function. The wash pump will continue to operate as long as the button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper. 177 CAUTION! Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If not equipped, your authorized dealer can order and install Mopart cross rails built specifically for this roof rack system or a number of after market rails that are tailored to your life-style or activities. The optional cross rails have five specific locations identified by a feature on both the side rail and the cross rail. Cross rails must be secured in one of the five detent locations on the side rail to prevent movement with a sudden stop.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 CAUTION! WARNING! • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without cross rails installed. The load should be secured and placed on top of the cross rails, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface. Cargo must be securely tied before driving your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel And Controls . . . . . . . . . . . . . 185 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 186 m Instrument Cluster Description . . . . . . . . . . . . . 187 m Electronic Vehicle Information Center (EVIC) . . . 195 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL m Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 ▫ Operating Instructions - Radio Mode . . . . . . . 212 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . . 220 ▫ Notes On Playing MP3/WMA Files . . . . . . . . 222 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 183 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 243 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 250 m Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 ▫ Operating Instructions - Satellite Mode . . . . . . 250 ▫ Connecting The iPodt . . . . . . . . . . . . . . . . . . 245 ▫ Controlling The iPodt Using Radio Buttons . . . 245 ▫ Play Mode . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Manual Air Conditioning And Heating System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 257 ▫ Automatic Temperature Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 260 ▫ Rear Climate Control — If Equipped . . . . . . . 267 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 269 ▫ Operating Tips Chart . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 185 INSTRUMENT PANEL AND CONTROLS 4 1 2 3 4 — Air Outlet — Instrument Cluster — Radio — Glove Box 5 6 7 8 — — — — Upper Switch Bank Power Outlet/Cigar Lighter Storage Bin Power Outlet 9 — Lower Switch Bank 10 — Climate Controls 11 — Ignition Switch 12 — Storage Bin
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light The BRAKE warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light stays on longer, it may be an indication that the parking brake has not been released.
UNDERSTANDING YOUR INSTRUMENT PANEL engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles.
UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 9. Security Alarm System Indicator Light — If Equipped This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. 191 CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 16. Electronic Stability Program (ESP) Warning Light/Brake Assist System (BAS) Warning Light The ESP/BAS warning light in the instrument cluster comes on when the ignition switch is turned to the “ON” position. The light should go out with the engine running. If the ESP/ BAS warning light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system.
UNDERSTANDING YOUR INSTRUMENT PANEL U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 21. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 22.
UNDERSTANDING YOUR INSTRUMENT PANEL 25. Voltage Warning Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 26. Low Fuel Warning Light When the fuel level reaches approximately 2.3 U.S. Gallons (8.7 Liters) this light will come on and remain on until fuel is added.
UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays • Personal Settings (Customer Programmable Features) • Compass Display • Outside Temperature Display • Trip Computer Functions The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: MENU Button Press and release the MENU button and the mode displayed will change between Trip Functions, Personal Settings, and System Status.
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages: • TURN SIGNAL ON • PERFORM SERVICE • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PROGRAM LIMIT • PROGRAMMING ACTIVE — NEW KEY PROGRAMMED 197 • DRIVER/PASSENGER DOOR OPEN (with graphic) • LEFT/RIGHT REAR DOOR OPEN (with graphic) • X DOORS
UNDERSTANDING YOUR INSTRUMENT PANEL • HOOD/GATE/DOOR OPEN (with graphic) • SERVICE SUSPENSION • HOOD/GATE/DOORS OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • LIFTGLASS/DOOR OPEN (with graphic) • TRANSMISSION OVER TEMP • LIFTGLASS/DOORS OPEN (with graphic) • CHECK SHIFT PROCEDURE • LIFTGLASS/HOOD OPEN (with graphic) • SERVICE 4WD SYSTEM • WASHER FLUID LOW (with graphic) • 4WD SYSTEM IN NEUTRAL • COOLANT LOW (with graphic) • LOW BRAKE FLUID LEVEL • OIL CHANGE REQUIRED • WARNING! LIMI
UNDERSTANDING YOUR INSTRUMENT PANEL • MEMORY #2 POSITIONS SET • MEMORY SYSTEM DISABLED — SEATBELT BUCKLED (with graphic) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • DRIVER 1 MEMORY • DRIVER 2 MEMORY • ADJ. PEDALS DISABLED — CRUISE CONTROL SET • ADJ.
UNDERSTANDING YOUR INSTRUMENT PANEL Engine Oil Change Indicator System Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL • Service Distance • Display Units of Measure in Press the SCROLL button to cycle through all the Trip Computer functions. display above the average fuel economy in the EVIC display. This message will appear whenever MDS allows the engine to operate on four cylinders, which will vary depending on driving habits and vehicle usage. The Trip Functions mode displays the following information: 4 • Average Fuel Economy / Fuel Saver Mode (5.
UNDERSTANDING YOUR INSTRUMENT PANEL This feature allows you to monitor when the MDS switches off the fuel on four of the eight cylinders and it can be used to modify driving habits in order to increase the time in which the fuel saver mode is active. • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank.
UNDERSTANDING YOUR INSTRUMENT PANEL • Trip A Shows the total distance traveled for trip A since the last reset. • Trip B Shows the total distance traveled for trip B since the last reset. • Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position.
UNDERSTANDING YOUR INSTRUMENT PANEL objects) until the “CAL” indicator displayed in the EVIC turns off. The compass will now function normally. Manual Compass Calibration If the compass appears erratic and the “CAL” indicator does not appear in the EVIC display, you must put the compass into the Calibration Mode manually as follows: 1. Turn on the ignition switch. 2. Press the MENU button until Personal Settings (Customer Programmable Features) menu is reached. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 1. Turn the ignition switch ON. 2. Press and hold the compass button for approximately 2 seconds. 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the compass button to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL Use the SCROLL button to display one of the following choices: Language When in this display you may select one of three languages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the FUNCTION SELECT button while in this display to select English, Espanol, or Francais. Then, as you continue, the information will display in the selected language. NOTE: The EVIC will not change the UConnect™ language selection.
UNDERSTANDING YOUR INSTRUMENT PANEL unlock button. To make your selection, press and release the FUNCTION SELECT button until “Driver Door 1st Press” or “All Doors 1st Press” appears. Sound Horn with Lock When Y (YES) is selected, a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. To make your selection, press and release the FUNCTION SELECT button until “Y (YES)” or “N (NO)” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Headlights On with Wipers (Available with Auto Headlights Only) When Y (YES) is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the FUNCTION SELECT button until “Y (YES)” or “N (NO)” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Key Off Power Delay When this feature is selected, the power window switches, radio, hands–free system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and release the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” or “10 min.” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL • Tire Pressure Monitor System (Shows the current pressure of all 4 road tires.) For additional information, refer to “Tire Pressure Monitor System” in Section 5 of this manual. NOTE: Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures” in Section 5 for additional information.
UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE control knob to save time change. 5. To exit, press any button/knob or wait 5 seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at step 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control knob a third time and TREBLE will display. Turn the TUNE control knob to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control knob a fourth time and BALANCE will display. Turn the TUNE control knob to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control knob a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16 Digit-Character Display Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL • DVD Enter - When the disc is in DVD Menu mode, selecting DVD Enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (If Equipped). • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (If Equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button will allow user to set the clock. Turn the TUNE control knob to adjust the hours and then press and turn the TUNE control knob to adjust the minutes. Press the TUNE control knob again to save changes. • Player Defaults - Selecting this item will allow the user to scroll through the following items, and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL Audio DRC — If Equipped Selecting this item will allow the user to limit maximum audio dynamic range - The default is set to 9High,9 and under this setting, dialogues will play at 11 db higher than if the setting is 9Normal.9 Aspect Ratio — If Equipped Selecting this item will allow the user to choose between wide screen, pan scan, and letter box.
UNDERSTANDING YOUR INSTRUMENT PANEL window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used, a corresponding button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The ignition switch must be in the ON or ACC position to operate the radio. LOAD Button — Loading Compact Disc(s) Press the LOAD button and the push-button with the corresponding number (1-6) where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays 9INSERT DISC,9 insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE) Press the Scan button to scan through each track on the CD currently playing. TIME Button (CD MODE) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of directory levels: 8 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9.9 and a 3-character extension) • Level 2: 31 (including a separator 9.9 and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files).
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. Operating Instructions - Hands Free Phone (UConnect™) (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section. TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Macrovision This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited 4 DTS 9DTS9 and 9DTS 2.09 are trademarks of Digital Theater Systems, Inc.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect™ Hands Free Phone) — If Equipped Press this button to operate the Hand Free Phone (UConnect™) feature (if equipped). Refer to “Hands-Free Communication (UConnect™)” in Section 3 for more information. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. TUNE Control Turn the right side rotary control clockwise to increase or counter-clockwise to decrease the frequency. Setting the Tone, Balance, and Fade Press the rotary TUNE control knob and BASS will display.
UNDERSTANDING YOUR INSTRUMENT PANEL program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to push-button memory {12 AM and 12 FM stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead.
UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for 5 seconds (when ignition is off). Operating Instructions - Hands Free Phone (UConnect™) (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section.
UNDERSTANDING YOUR INSTRUMENT PANEL to the car speakers while different audio tracks play through the system’s wireless headphones. This means rear seat passengers can watch a DVD on the optional rear-seat entertainment system while the driver and front seat passenger listen to the radio. Operating Instructions — Hands-Free Communication (UConnect™) (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed. 5. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone 1. Turn on the system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 4. Select a time zone by touching the screen where your selection appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailed operating instructions. Clock Setting Procedure The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellite. The satellites’ clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing Daylight Savings Time 1. Press the Time soft key on the lower left side of the face of the radio. 2. Press the Daylight Savings soft key when Daylight Savings Time is in effect. 3. Press the SAVE soft key on the face of the radio. Press the CANCEL soft key to exit from the clock setting mode. UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES and REQ radios only with UConnect.
UNDERSTANDING YOUR INSTRUMENT PANEL Connecting the iPodT Use the optional connection cable to connect an iPodt to the vehicle’s UCI connector (which is located in the glove box on some vehicles. This location may vary with vehicle). Once the iPodt is connected and synchronized to the vehicle system (this may take a few seconds to connect), the vehicle brand logo appears on the iPodt display, and it starts charging and is ready for use by pressing radio switches as described below.
UNDERSTANDING YOUR INSTRUMENT PANEL RW (Rewind) Button Press and hold the “RW” button to move backward in the current track. Holding the “RW” button long enough will take you back to the beginning of the current track. Pressing and releasing the “RW” button will go back 5 seconds of the current track. FF (Fast Forward) Button Press and hold the “FF” button to move forward in the current track. Pressing and releasing the “FF” button will go forward 5 seconds of the current track.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button Pressing the “SCAN” button will play the first 5 seconds of each track in the current list and then forward to the next song. To stop the SCAN mode and start playing the desired track, press the “SCAN” button again. During the SCAN mode, you can also press the SEEK button to the left or right to go to the previous or next tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL During all List modes, the iPodt will display all lists in “wrap-around” mode. So if the track you wish to select is at the bottom of the list, you just turn the “TUNE/ SCROLL” knob backwards (counter-clockwise) to get to the track faster. Radio Preset Buttons In the List mode, the radio preset buttons are used as shortcuts to the following lists on the iPodt.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 SATELLITE RADIO (RSC) — IF EQUIPPED (REQ AND RES RADIOS ONLY) Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL selected. Press the TUNE control knob and the Sirius ID number will display. The Sirius ID number display will time out in 2 minutes. Press any button on the radio to exit this screen. Selecting Satellite Mode Press the SAT button until 9SAT9 appears in the display. A CD may remain in the radio while in the Satellite radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next channel, pausing for 8 seconds before continuing to the next.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset channel.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual. Operating Instructions - Video Entertainment System (VEST) (If Equipped) Refer to separate “Video Entertainment System (VESt) Guide.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center.
UNDERSTANDING YOUR INSTRUMENT PANEL The center button on the left side rocker switch has no function for a single disc CD player. However, when a multiple disc CD player is equipped on the vehicle, the center button will select the next available CD in the player. 5. Store the disc in its case after playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 CLIMATE CONTROLS Manual Air Conditioning and Heating System — If Equipped The controls for the heating/air conditioning and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. 4 Manual Air Conditioning and Heating Controls The instrument panel features four dual-vane airflow registers.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Mode Control The rotary knob on the left controls the blower and can be set in one of four speeds and OFF. The blower fan motor will remain on until the system is turned to the OFF position or the ignition is turned OFF. The mode selector (the right rotary knob) can be placed in several positions. Dots between each of the mode selections identify intermediate modes that allow the occupants to fine tune airflow distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL side window demister grilles. Some airflow is delivered to the floor while in defrost so that comfort can be maintained. Floor Air flows through the floor outlets located under the instrument panel and into the rear seating area through vents under the front seats. Some airflow is delivered to defrost while in the floor mode so that comfort can be maintained. Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor.
UNDERSTANDING YOUR INSTRUMENT PANEL located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The numbers on the temperature dial represent a comfort setting when the Mode knob is set to Auto, and not the actual air temperature. Operation of the system is quite simple. Begin by turning the right mode knob to AUTO, and place the blower control (left knob) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present.
UNDERSTANDING YOUR INSTRUMENT PANEL The system will automatically control recirculation. However, pressing this button will temporarily put the system in recirculation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are present. This will cause the LED to illuminate. NOTE: • The surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation This system offers a full complement of manual override features which consist of Blower Preferred Automatic, Mode Preferred Automatic with Manual Air Temperature Control and Manual. This means the customer can override the blower, mode and disable automatic temperature control completely. 263 NOTE: Please read the Automatic Temperature Control Operation Chart below for details.
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions. When the Mode is set to any position other than AUTO, The automatic control of air temperature is disabled.
UNDERSTANDING YOUR INSTRUMENT PANEL Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • Panel Air flows through the outlets located in the instrument panel. Air flows through the registers in the back of the center console to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Rear Climate Control — If Equipped The Manual Rear Climate Control system has one floor air outlet (passenger side), and two panel outlets in the rear quarter trim (on each side). The unit provides warm or cool air through the floor and upper outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL The rear temperature, blower speed, and mode control can be adjusted as desired by the third row seat occupants. Rear Blower Control The left knob on the Rear Control Panel has four positions, “Off”, and a range of three blower speeds. This allows the third row seat occupants to control the volume of air circulated in the rear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control The center knob on the Rear Control Panel allows the third row seat occupants to have control of the rear temperature as follows: • When the temperature knob is in the cold (Blue) position, cold air will be delivered from the outlets. As the temperature knob is turned towards the hot (Red) position, the air will get warmer. 269 • Panel Air flows through the outlets located in the rear quarter trim panels.
UNDERSTANDING YOUR INSTRUMENT PANEL Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 277 ▫ Brake/Transmission Interlock System . . . . . . . 283 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 278 ▫ 5–Speed Automatic Transmission . . . . . . . . . . 283 ▫ Extremely Cold Weather (Below 220°F Or 229°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 283 ▫ If Engine Fails To Start . . . . . . . . . . .
STARTING AND OPERATING ▫ Shifting Procedures . . . . . . . . . . . . . . . . . . . . 293 m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 305 ▫ Quadra-Drive IIt System — If Equipped . . . . . 295 m Multi Displacement System (MDS) — 5.7L Engine Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 m On-Road Driving Tips . . . . . . . . . . . . . . . . . . . 296 m Off-Road Driving Tips . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 275 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 319 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 334 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 320 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 335 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 320 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 335 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 321 ▫ Materials Added To Fuel . .
STARTING AND OPERATING ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 352 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . . . 340 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 353 m Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 341 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 357 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. 277 WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING Normal Starting The gear selector must be in the “N” (Neutral) or “P” (Park) position before you can start the engine. Apply the brakes before shifting into any driving gear. NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages.
STARTING AND OPERATING If Engine Fails to Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
STARTING AND OPERATING After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. The engine block heater cord is located: ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the heater cord to a ground-fault interrupter protected 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. • 5.7L Engine — bundled and fastened to the injector harness.
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into P (Park) only after the vehicle has come to a complete stop. • Shift into or out of R (Reverse) only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from R (Reverse), P (Park), or N (Neutral) into any forward gear when the engine is above idle speed.
STARTING AND OPERATING 1. Firmly set the parking brake. 2. Using a flat blade screwdriver, carefully remove the shift lock manual override cover which is located on the PRNDL bezel. 3. Depress and maintain firm pressure on the brake pedal. 4. Using the screwdriver, reach into the manual override opening. Press and hold the shift lock lever down. 5. Move the shift lever into the N (Neutral) position. 6. The vehicle may then be started in N (Neutral).
STARTING AND OPERATING Brake/Transmission Interlock System This system prevents you from moving the gear shift out of P (Park) and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON position. Always depress the brake pedal first, before moving the gear selector out of P (Park). 5–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule.
STARTING AND OPERATING WARNING! Never use P (Park) position as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. WARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
STARTING AND OPERATING Electronic Range Select (ERS)Operation The Electronic Range Select (ERS) shift control allows you to move the shifter left (-) or right (+) when the shifter is in the D (Drive) position, allowing the selection of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed.
STARTING AND OPERATING NOTE: To select the proper gear position for maximum deceleration (engine braking), move the shift lever to the left “D(-)” and hold it there. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (5th gear for 3.7L engine, 4th and 5th gears for 4.7L and 5.7L engines).
STARTING AND OPERATING OVER TEMP” message may display and the transmission may downshift out of Overdrive until the transmission cools down. After cool down, the transmission will resume normal operation. 287 overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, the transmission will shift to direct gear and Overdrive will be enabled under steady cruise conditions.
STARTING AND OPERATING activated. Pressing the switch a second time restores normal operation. If the “TOW/HAUL” mode is desired, the switch must be pressed each time the engine is started. Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7L engine) or in direct gear (4.7L and 5.
STARTING AND OPERATING 289 drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The feature is operational in Overdrive and in Drive. cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving].
STARTING AND OPERATING selector in N (Neutral) for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle. CAUTION! When “rocking” a stuck vehicle by moving between “First” and R (Reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.
STARTING AND OPERATING Quadra-Trac IIT Operating Instructions/Precautions — If Equipped The Quadra-Trac IIt transfer case is fully automatic in the normal driving 4 HI mode. The Quadra-Trac IIt transfer case provides three mode positions — four wheel drive high range, neutral, and four wheel drive low range. This transfer case is fully automatic in the 4 HI mode.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake. The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 293 Shifting Procedures 4 HI to 4 LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into N (Neutral), and raise the transfer case T-handle. “The 4WD LOW Indicator Lamp” in the instrument cluster will begin to flash and remain on solid when the shift is complete. Release the T-handle.
STARTING AND OPERATING LOW Indicator Lamp” in the instrument cluster will flash and go out when the shift is complete. Release the T-handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
STARTING AND OPERATING Neutral Switch 5. Repeat Steps 1– 4 to shift out of Neutral. NOTE: If shift conditions/interlocks are not met, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. 295 Quadra-Drive IIT System — If Equipped The optional Quadra-Drive IIt System features three torque transfer couplings.
STARTING AND OPERATING ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.
STARTING AND OPERATING CAUTION! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few inches deep will require extra caution to ensure safety and prevent damage to your vehicle.
STARTING AND OPERATING Driving In Snow, Mud and Sand In heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4WD LOW if necessary. Refer to “Four-Wheel Drive Operation” in this section. Do not shift to a lower gear than necessary to maintain forward motion. Over-revving the engine can spin the wheels and traction will be lost.
STARTING AND OPERATING Remember, never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain forward motion by turning the front wheels slowly. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. Traction Downhill Shift the transmission into a low gear and the transfer case to 4WD LOW range.
STARTING AND OPERATING • After extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.
STARTING AND OPERATING 301 WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also, be certain to leave the transmission in P (Park). Failure to do so may allow the vehicle to roll and cause damage or injury. Parking Brake Be sure the parking brake is firmly set when parked and the gear shift lever is in the P (Park) position.
STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING 303 WARNING! WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning.
STARTING AND OPERATING 305 build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action.
STARTING AND OPERATING CAUTION! TIRE SAFETY INFORMATION Tire Markings Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. MULTI DISPLACEMENT SYSTEM (MDS) — 5.7L Engine Only This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions.
STARTING AND OPERATING 307 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 309 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 311 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 315 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING 319 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 321 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Only models fitted with 235/65R17XL (extra load) tires have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only.
STARTING AND OPERATING 323 aggressive tread designs such as those on On/Off Road type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
STARTING AND OPERATING decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period. Refer to the “Tires – General Information” in this section for information on how to properly inflate the vehicle’s tires.
STARTING AND OPERATING Telltale Light” will turn OFF only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if under-inflation has not reached the level to trigger illumination of the “Tire Pressure Monitoring Telltale Light.” • Seasonal temperature changes will affect tire pressure, and the TPM system will monitor the actual tire pressure in the tire.
STARTING AND OPERATING 327 inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The system will automatically update and the “Tire Pressure Monitoring Telltale Light” will extinguish once the updated tire pressures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. 1.
STARTING AND OPERATING 10 minutes above 15 mph (24 km/h) will turn OFF the “Tire Pressure Monitoring Telltale Light” as long as none of the road tires are below the low pressure warning threshold. NOTE: If your vehicle is not equipped with a matching full size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The TPMS will not be able to monitor the tire pressure.
STARTING AND OPERATING The Tire Pressure Monitor System (TPMS) consists of the following components: • Receiver Module • 4 Tire Pressure Monitoring Sensors • 3 Trigger Modules (mounted in three of the four wheel wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC), and a graphic displaying tire pressures • Tire Pressure Monitoring Telltale Light A tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped
STARTING AND OPERATING NOTE: Your system can be set to display pressure units in PSI, kPa, or BAR. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure.
STARTING AND OPERATING 331 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
STARTING AND OPERATING in the EVIC, and the graphic display will still show the low tire pressure value flashing. Driving the vehicle for up to 10 minutes above 15 mph (24 km/h) will turn OFF the “Tire Pressure Monitoring Telltale Light” as long as none of road tires are below the low pressure warning threshold. The EVIC will also display a “Spare Low Pressure” text message, and the graphic display will show a tire pressure value in place of the flashing low tire pressure value.
STARTING AND OPERATING be driven for up to 10 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
STARTING AND OPERATING using high quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended. Under normal conditions, the use of premium gasoline will not provide a benefit over high quality regular and mid-grade gasolines, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING E-85 Fuel Cap CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. E-85 Badge ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
STARTING AND OPERATING WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame. Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two.
STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the same. Refer to “Maintenance Procedures” in Section 7 of this manual for the proper quality and viscosity engine oil. Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C).
STARTING AND OPERATING 341 CAUTION! • Replacing fuel system components with nonethanol compatible components can damage your vehicle. • Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability. 5 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
STARTING AND OPERATING WARNING! • Never add fuel when the engine is running. • Never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled. VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar.
STARTING AND OPERATING Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability does not necessarily increase the vehicle’s GVWR. Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
STARTING AND OPERATING or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving.
STARTING AND OPERATING Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its 9loaded and ready for operation9 condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING Frontal Area The maximum height and maximum width of the front of a trailer. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
STARTING AND OPERATING 349 5 Weight Distributing Hitch System Improper Adjustment of Weight Distributing System
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING Engine/ Transmission 3.7L/ Automatic 3.7L/ Automatic 4.7L/ Automatic 4.7L/ Automatic 5.7L/ Automatic 5.7L/ Automatic Model 4x2 GCWR (Gross Combined Wt. Rating) 8,670 lbs (3 933 kg) 4x4 8,755 lbs (3 971 kg) 4x2 11,665 lbs (5 291 kg) 4x4 11,800 lbs (5 352 kg) 4x2 12,470 lbs (5 656 kg) 4x4 12,620 lbs (5 724 kg) Refer to local laws for Frontal Area Max. GTW (Gross Trailer Wt.) 3,500 lbs (1 587 kg) 40 Sq. Ft (3.72 square meters) 40 Sq. Ft (3.
STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the “Tire—Safety Information” section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. Make certain that the load is secured in the trailer and will not shift during travel.
STARTING AND OPERATING 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the “Tires–General Information” section for proper tire inflation procedures.
STARTING AND OPERATING actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
STARTING AND OPERATING 357 The Trailer Tow Package may include a 4 and 7 pin wiring harness. Use a factory approved trailer harness and connector. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 5 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”Tow/ Haul” mode (if equipped) or a lower gear range should be selected. NOTE: Using the ”Tow/Haul” mode (if equipped) or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up.
STARTING AND OPERATING 359 − Air Conditioning Turn off temporarily. Towing — Quadra-Trac I (Single-Speed Transfer Case) 4WD Models − refer to Cooling System Operating information in the Maintenance section of this manual for more information. Recreational towing is not allowed. This model does not have a N (Neutral) position in the transfer case. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing – 2WD Models Recreational towing is allowed ONLY if the driveshaft is removed.
STARTING AND OPERATING Shifting Into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing. CAUTION! on solid) when Neutral shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
STARTING AND OPERATING 5. Start engine. 6. Shift transmission into D (Drive). 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into P (Park). 10. Place the ignition key in the OFF position, and remove key. 361 CAUTION! Transmission damage may occur if the transmission is shifted into P (Park) with the transfer case in N (Neutral) and the engine running.
STARTING AND OPERATING Hold down N (Neutral) “pin” switch (with a pen, etc.) for 4 seconds until the LED lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL” message will no longer be displayed on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Neutral Switch 5. Shift transmission into P (Park). 6. Start the engine. 7.
STARTING AND OPERATING NOTE: When shifting out of transfer case N (Neutral), turning the engine OFF may be required to avoid gear clash. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake. The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
STARTING AND OPERATING
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flashers . . . . . . . . . . . . . . . . . 366 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 371 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 367 m Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 374 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 368 m Emergency Tow Hooks — If Equipped . . . . . . . . 377 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not to be used when the vehicle is in motion. To activate the warning flashers, press the button on the upper switch bank.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Jack Location The scissor-type jack and tire changing tools are located in a compartment behind the third row seat.
WHAT TO DO IN EMERGENCIES 369 Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the liftgate opening. CAUTION! Do not use power tools to winch the tire up or down. Impact type tools can damage the winch mechanism.
WHAT TO DO IN EMERGENCIES CAUTION! WARNING! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
WHAT TO DO IN EMERGENCIES 371 Jacking Instructions 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools as shown. Connect jack handle driver (A) to two extensions (B), then to the lug wrench (C).
WHAT TO DO IN EMERGENCIES 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise.
WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered.
WHAT TO DO IN EMERGENCIES NOTE: Tire should be stowed with the “beauty” side up. Storing the tire upside down may result in scratching or damage to the wheel face. Continue winching up the tire until you hear the winch “ratchet” three times. Double check to ensure the tire is snug against the underbody of the vehicle. Damage to the winch cable may result if the vehicle is driven with the tire loose. WARNING! Do not use power tools to winch the tire up or down.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. TOWING A DISABLED VEHICLE 2WD Models Only Provided the transmission is operable, tow only in N (Neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km) can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment – 3.7L . . . . . . . . . . . . . . . 382 m Maintenance Procedures . . . . . . . . . . . . . . . . . . 389 m Engine Compartment – 4.7L . . . . . . . . . . . . . . . 383 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 389 m Engine Compartment – 5.7L . . . . . . . . . . . . . . . 384 ▫ Drive Belts — Check Condition And Tension . . 392 m Onboard Diagnostic System — OBD II . . . . . . . . 385 ▫ Spark Plugs . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 397 ▫ Maintenance After Off-Road Driving . . . . . . . . 414 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 398 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 399 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 400 ▫ Windshield Washers — Front And Rear . . . . .
MAINTAINING YOUR VEHICLE 381 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 431 m Fluids, Lubricants, And Genuine Parts . . . . . . . . 436 ▫ Rear Tail, Stop, Turn Signal, And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 ▫ Center High Mounted Stop Light (CHMSL) . . . 434 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 m Fluids And Capacities . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 3.
MAINTAINING YOUR VEHICLE 383 ENGINE COMPARTMENT – 4.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A “CHECK GASCAP” message will be displayed in the EVIC (Refer to Section 4 of this manual). Tighten the gas cap until a 9clicking9 sound is heard. This is an indication that the gas cap is properly tightened. This message may be temporarily overridden by pressing either the C/T, STEP, or MENU buttons.
MAINTAINING YOUR VEHICLE 387 is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement.
MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle’s OBD system is ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Change Engine Oil Refer to the Maintenance Schedule for recommended engine oil change intervals.
MAINTAINING YOUR VEHICLE NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil. Failure to do so may result in improper operation of the Multiple Displacement System (MDS). Refer to “Multi Displacement System” in Section 5 for more details. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopart engine oil filters are high quality oil filters and are recommended. Drive Belts — Check Condition and Tension Belt tension is controlled by means of an automatic tensioner.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Refer to the Maintenance Schedule for recommended Engine Air Cleaner Filter change intervals. WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc) unless such removal is necessary for repair or maintenance.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. 397 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, and Refrigerants. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner to remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to wipe frost or ice from the windshield.
MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE system should be drained, flushed and refilled with fresh antifreeze/coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of antifreeze/coolant other than the specified HOAT antifreeze/coolant may result in decreased corrosion protection and engine damage. If a nonHOAT antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coolant as soon as possible. Do not use plain water alone or alcohol base antifreeze/coolant products.
MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol-based antifreeze/coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze/ coolant needs to be added, contents of coolant recovery bottle must also be protected against freezing.
MAINTAINING YOUR VEHICLE Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold.
MAINTAINING YOUR VEHICLE fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking.
MAINTAINING YOUR VEHICLE Front/Rear Axle Fluid Transfer Case Front Axle Fluid Level Check Lubricant should be to the bottom of the oil fill hole. Fluid Level Check Inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be checked by removing the filler plug located on the back side of the transfer case. The fluid level should be at the bottom edge of the filler plug hole when the vehicle is in a level position.
MAINTAINING YOUR VEHICLE CAUTION! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Automatic Transmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance.
MAINTAINING YOUR VEHICLE If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. To check the automatic transmission fluid level properly, the following procedure must be used: CAUTION! 1. Operate the engine at idle speed and normal operating temperature. The fluid level is preset at the factory and it does not require adjustment under normal operating conditions.
MAINTAINING YOUR VEHICLE the fluid is low, add as required into the dipstick tube. Do not overfill. After adding any quantity of oil through the oil fill tube, wait a minimum of two (2) minutes for the oil to fully drain into the transmission before rechecking the fluid level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at approximately 70°F (21°C) (room temperature).
MAINTAINING YOUR VEHICLE Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.
MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. 415 • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly.
MAINTAINING YOUR VEHICLE CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopart Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopart cleaners are recommended. Do not use oven cleaner.
MAINTAINING YOUR VEHICLE Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopart Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters.
MAINTAINING YOUR VEHICLE 419 2. Dry with a soft tissue. FUSE PANEL Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. Interior Fuses The fuse panel is on the lower instrument panel just to the left of the steering column. If the belts need cleaning, use Mopart Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them.
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 Cartridge Mini Fuse Fuse 30 Amp Green 15 Amp Blue 10 Amp Red 20 Amp Yellow 10 Amp Red Spare (B+) 20 Amp Yellow 15 Amp Blue Audio Amp (B+) Cavity 9 Sunroof (B+) 10 Description Htd Mirror (EBL) Rr Pwr Out (B+) Rr HVAC (R/O) (Commander Only) Door Locks (B+) Steer Col Lock (B+) (ELV) 11 12 Cartridge Mini Fuse Description Fuse 20 Amp Pwr Outlet (B+) Yellow 10 Amp Final Drive Control Red Module (FDCM), Heater Ventilation, Air Conditioning (HVAC), Swit
MAINTAINING YOUR VEHICLE Cavity 13 14 15 16 17 19 20 Cartridge Mini Fuse Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue Spare (R/S) 10 Amp Red Description Autowipe (R/A) Cavity 21 Cigar Ltr (R/A) 22 Tire Pressure Transducers (R/O) Steering Control Module (SCM), Diag.
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Power Distribution Center Cav- Cartridge Mini Fuse Description ity Fuse 1 50 Amp PTC Heater 1 (Diesel Green Only) Cav- Cartridge Mini Fuse Description ity Fuse 2 40 Amp HID Headlamps Green 3 50 Amp PTC Heater 2 (Diesel Green Only) 4 30 Amp Power Outlets Pink 5 50 Amp PTC Heater 3 (Diesel Red Only) 6 30 Amp Cig Lighter, Trail Tow Pink Batt 7 40 Amp Power Liftgate (ComGreen mander Only) 8 40 Amp Starter, JB Power Green 9 — Spare 10
MAINTAINING YOUR VEHICLE Cav- Cartridge Mini Fuse Description ity Fuse 11 40 Amp HVAC Blower Green 12 30 Amp Rear Wiper, Ign R/O Pink 13 40 Amp Rear Window DeGreen froster (EBL)/Heated Mirror 14 30 Amp Rear HVAC (If Pink Equipped) 15 — Spare 16 50 Amp ASD Red 17 30 Amp ABS Pump Pink 18 40 Amp Accessory Delay, Seats Green Cav- Cartridge Mini Fuse ity Fuse 19 40 Amp Green 20 — 21 20 Amp Yellow 22 20 Amp Yellow 23 25 Amp Natural 24 20 Amp Yellow 25 20 Amp Yellow 26 15 Amp Blue 423 Description JB Power Spar
MAINTAINING YOUR VEHICLE Cavity 27 28 29 30 31 32 33 34 35 Cartridge Mini Fuse Fuse 20 Amp Yellow 30 Amp Green 20 Amp Yellow — — 15 Amp Blue 20 Amp Yellow — 20 Amp Yellow Description HD Washer (If Equipped) ABS Valves Cavity 36 37 38 PCM Batt (Gasoline Only) Spare Spare Powertrain Control Module (Diesel Only) Final Drive Control Module (FDCM) E-Diff Spare Trail-Tow Mod (BUX Only) 39 40 41 42 43 44 Cartridge Mini Fuse Fuse — 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 25 Amp Natural — — 25 Amp Na
MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Cavity 9 10 12 13 14 Integrated Power Module Cavity 8 Cartridge Mini Fuse Description Fuse 10 Amp Lt Park Lamps Red 15 16 17 Cartridge Mini Fuse Fuse 10 Amp Red 10 Amp Red 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 425 Description Trailer-Tow Park Lamps Rt Park Lamps Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal Ft Fog Lamps Horn Rear Wiper 7
MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 27 28 Cartridge Mini Fuse Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 50 Amp Red 15 Amp Blue 20 Amp Yellow Description Front Control Module (FCM) Batt #1 Lt Trailer-Tow Stop/ Turn Front Control Module (FCM) Batt #3 Rt Trailer-Tow Stop/ Turn Final Drive Control Module (FDCM) MOD Radiator Fan Ignition Off Draw (IOD) #1 Ignition Off Draw (IOD) #2 Cavity 29 30 Cartridge Mini Fuse Fuse 10 Amp Red 10 Amp Red Description Occ
MAINTAINING YOUR VEHICLE • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb Type Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Grab Handle Light . . . . . . . . . . .
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Head Light 1. Open the hood. 2. Remove the headlamp cover. Insert a finger into each hole of the headlamp cover, and pull upward to unsnap the rear edge of the cover from the two upper lamp mounting brackets. Slide the cover rearward to disengage the front edge from beneath the tab on the top near the front of the lamp housing. 3. Disconnect the electrical connector. 4. Turn the low or high beam bulb 1/4 turn counter clockwise to unlock it from the housing.
MAINTAINING YOUR VEHICLE 429 5. Pull the bulb and base straight out from the opening in the reflector. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
MAINTAINING YOUR VEHICLE Front Turn Signal 1. Turn the steering wheel all the way to the left or right. 3. Reach through the access hole to access the park/turn signal bulb socket on the bottom of the front lamp unit housing. 2. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the bulb can be gained through the wheel liner hole.
MAINTAINING YOUR VEHICLE 4. Turn the socket on the bottom of the front lamp unit housing 1/4 turn counter clockwise to unlock it. 5. Pull the socket and bulb straight out from the opening in the housing. 6. Disconnect the electrical connector. 7. Pull the base of the bulb straight out of the socket. 431 Front Fog Light 1. Turn the steering wheel all the way to the left or right. 2.
MAINTAINING YOUR VEHICLE 3. Reach through the access hole to access the back of the front fog light housing on the back of the front fascia. 4. Disconnect the electrical connector. 5. Turn the socket on the back of the housing 1/4 turn counter clockwise to unlock it. 6. Pull the socket and bulb straight out from the opening in the housing. 7. Pull the base of the bulb straight out of the socket. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
MAINTAINING YOUR VEHICLE 433 3. Pull the outboard side of the rear lamp unit rearward far enough to unsnap the two ball studs on the outboard side of the lamp housing from the two plastic grommets in the quarter outer panel. Pull the lamp unit rearward far enough away to access the bulbs. 4. Firmly grasp the appropriate bulb socket on the back of the rear lamp unit housing, and turn 1/4 turn counter clockwise to unlock it.
MAINTAINING YOUR VEHICLE 7. Pull the base of the bulb straight out of the socket. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4.
MAINTAINING YOUR VEHICLE 435 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 4.7 Liter Engine (SAE 5W-20, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) Cooling System * 3.7 Liter Engine (Mopart Engine Coolant/Antifreeze 5 Year/ 100,000 Mile Formula) 4.7 Liter Engine (Mopart Engine Coolant/Antifreeze 5 Year/ 100,000 Mile Formula) 5.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (3.7L/4.7L/5.7L Engines) Oil Filter (All Engines) Spark Plugs (3.7L Engine) Spark Plugs (4.7L Engine) Spark Plugs (5.7L Engine) Fuel Selection (3.7L and 4.7L Engines) Fuel Selection (5.
MAINTAINING YOUR VEHICLE 437 Chassis Component Automatic Transmission Transfer Case (NV140 Single Speed Only) Transfer Case (NV245 Two Speed Only) Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Mopart ATF+4 Automatic Transmission Fluid Mopart ATF+4 Automatic Transmission Fluid Mopart NV 247/245 Transfer Case Lubricant Mopart Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 440 m Maintenance Schedule — Gasoline Engines . . . . 440 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 440 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 441 M A • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Check the windshield washer solvent and add if I N required. T • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Once a Month Your dealer will reset the oil change indicator message after completing the scheduled oil change.
M A I N T E N A N C E S C H E D U L E S 8 442 MAINTENANCE SCHEDULES At Each Oil Change Required Maintenance Intervals • Change the engine oil filter. NOTE: ** Vehicles built with the 4.7L engine are equipped with sixteen spark plugs, one set is located on the top of the engine under the coils and the second set is located on the side of the engine. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
MAINTENANCE SCHEDULES 443 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary.
M 444 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Replace the engine air cleaner filter. C Check the PCV valve, replace if necessary. Perform E the first inspection at 60,000 miles (100 000 km) or 60 S C H E D U L E S 8 months. Inspect the transfer case fluid. Replace the top row of spark plugs (4.7L Only). ** Replace the spark plugs (3.7L/5.7L Engines).
MAINTENANCE SCHEDULES 445 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Replace the side row of spark plugs (4.7L Only). ** Change the automatic transmission fluid & filter. Replace accessory drive belt(s) (3.7L/4.7L/5.7L Engines). WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 ▫ Prepare For The Appointment . . . . . . . . . . . . 448 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 448 m Reporting Safety Defects . . . . . . . . . . . . . . . . . . 451 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 452 m Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http:// www.safercar.gov. In Canada: If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. • Owner’s Manuals.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 188,302 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 177 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 135 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 393 Air Conditioner Maintenance . . . . . . . . . . . . . . . 397 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 259 Air Conditioning, Operating Tips . . . . . . .
INDEX Fluid and Filter Changes . . . . . . . . . . . . . . . . . 411 Fluid Level Check . . . . . . . . . . . . . . . . . . . 411,412 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 Special Additives . . . . . . . . . . . . . . . . . . . . . . 414 Torque Converter . . . . . . . . . . . . . . . . . . . . . . 288 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Auxiliary Electrical Outlet (Power Outlet) . . . . . . 169 Auxiliary Power Outlet . . . . . . . . . . . .
INDEX Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . 174 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 177 Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 174 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . . 393 CD (Compact Disc) Player . . . . . . . . . . . . . . . . . 239 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Center High Mounted Stop Light . . . . . . . . . . . . 434 Certification Label . . . . . . . . . .
INDEX Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 404 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . . 404 Selection of Coolant (Antifreeze) . . . . . . . . . 402,435 Courtesy Lights . . . . . . . . . . . . . . . . . . . . . . . . . 130 Crankcase Emission Control System . . . . . . . . . . 395 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Customer Assistance . . . . . . . . . . .
INDEX Electronic Brake Control System . . . . . . . . . . . . . 139 Anti-Lock Brake System . . . . . . . . . . . . . . . . . 139 Brake Assist System . . . . . . . . . . . . . . . . . . . . 141 Electronic Roll Mitigation . . . . . . . . . . . . . . . . 142 Electronic Stability Program . . . . . . . . . . . . . . . 143 Traction Control System . . . . . . . . . . . . . . . . . 140 Electronic Roll Mitigation (ERM) . . . . . . . . . . . . . 142 Electronic Speed Control (Cruise Control) . . . . . .
INDEX Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 191 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . 390 Engine Oil Viscosity Chart . . . . . . . . . . . . . . . . . 390 Enhanced Accident Response Feature . . . . . . . . . . 56 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 21 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 58 Exhaust Gas Caution . . . . . . . . . . . . .
INDEX Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . 113,117 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . 290 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Four Wheel Drive Operation . . . . . . . . . . . . . . . . 290 Four-Way Hazard Flasher . . . . . . . . . . . . . . . . . . 366 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 289 Front Axle (Differential) . . . .
INDEX GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Hands-Free Phone (UConnect™) . . . . . . . . . . . . . . 82 Hard Drive (HDD) . . . . . . . . . . . . . . . . . . . . . . . 239 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 366 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 110 Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Bulb Replacement . . . . . . .
INDEX Instrument Panel and Controls . . . . . . . . . . . . . . 185 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 418 Integrated Power Module (Fuses) . . . . . . . . . . . . 425 Interior Appearance Care . . . . . . . . . . . . . . . . . . 417 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 130 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 127,130 Intermittent Wipers (Delay Wipers) . . .
INDEX Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . 125 Brake Assist Warning . . . . . . . . . . . . . . . . . 152,193 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 187 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 428 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 434 Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 130 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Daytime Running . . . . . . . . . . . . . . . .
INDEX Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 190 Tow/Haul Indicator . . . . . . . . . . . . . . . . . . . . 192 Traction Control . . . . . . . . . . . . . . . . . . . . 152,189 Turn Signal . . . . . . . . . . . . . . . . . . 124,129,430,432 Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Load Floor, Cargo . . . . . . . . . . . . . . . . . . . . . . . 174 Loading Vehicle . . . . . . . . . . . . . .
INDEX Modifications/Alterations, Vehicle . . . . . . . . . . . . . 9 Monitor, Tire Pressure System . . . . . . . . . . . . . . . 323 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 388,451 MP3 Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Multi-Displacement Engine System . . . . . . . . . . . 306 Multi-Function Control Lever . . . . . . . . . . . . . . . 124 Navigation Radio . . . . . . . . . . . . . . . . . . . . . . . . 242 Navigation System . . . . . . . . . . . . . .
INDEX Overheating, Engine . . . . . . . . . . . . . . . . . . . 192,367 Owner’s Manual (Operator Manual) . . . . . . . . . . 452 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Paint Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 153 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Passing Light . . . . . . .
INDEX Quadra-Trac . . . . . . . . . . . . . . . . . . . . . . . . . 290,291 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 318 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 210 Radio, Navigation . . . . . . . . . . . . . . . . . . . . . . . 242 Radio Operation . . . . . . . . . . . . . . . . . . . . . . 240,256 Radio, Satellite . . . . . . . . . . . . . . . . . 239,240,243,249 Radio (Sound Systems) . . . . . . . . . . . . . . . . . . . . 239 Rain Sensitive Wiper System .
INDEX Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 38 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 289 Roll Over Warning . . . . . . . . . . . . . . . . . . . . . . . . 5 Roof Type Carrier . . . . . . . . . . . . . . . . . . . . . . . 177 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 322 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 71 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 72 Safety Defects, Reporting . . .
INDEX Rear Folding . . . . . . . . . . . . . . . . . . . . . . . 113,117 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Seatback Release . . . . . . . . . . . . . . . . . . . . . . . 117 Security Alarm (Theft Alarm) . . . . . . . . . . . . . 20,189 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 390 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 17 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 19 Sentry Key Replacement . . . . . . . .
INDEX Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 305,398 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426 Storage, Vehicle . . . . . . . .
INDEX Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Load Capacity . . . . . . . . . . . . . . . . . . . . . . 311,312 Pressure Monitor System (TPMS) . . . . . . . . . . . 323 Pressure Warning Light . . . . . . . . . . . . . . . . . . 190 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 454 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 320 Rotation . . . . . . . . . . . . . . . . . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 411 Range Indicator . . . . . . . . . . . . . . . . . . . . . . . 194 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLinkt) . . 159 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Washers, Windshield . . . . . . . . . . . . . . . . . . 131,400 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 415 Waxing and Polishing . . . . . . . . . . . . . . . . . . . . . 415 Wheel Alignment and Balance . . . . . . . . . . . . . . . 321 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 417 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 417 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . . . 373 Wind Buffeting . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION ROLLOVER WARNING HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Wireless Ignition Node (WIN)Fob with Integrated Key (FOBIK)Ignition Key RemovalKey-In-Ignition ReminderSENTRY KEY Replacement KeysCustomer Key (Fob) ProgrammingGeneral InformationSECURITY ALARM SYSTEM - IF EQUIPPED To Set the AlarmTo Disarm the SystemILLUMINATED ENTRY REMOTE KEYLESS ENTRY To
