2008 Patriot 2008 OWNER’ S MANUAL 81-326-0812 First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 7 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
6 INTRODUCTION
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .12 䡵 Security Alarm System — If Equipped . . . . . . . . .18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ To Set The Security Alarm . . . . . . . . . . . . . . . .18 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 ▫ To Disarm The Security Alarm System . . . . . . .19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters . . . . . . . .22 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .35 ▫ General Information . . . . . . . . . . . . . . . . . . . .24 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .36 ▫ Transmitter Battery Replacement . . . . . . . . . . .24 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .41 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Engine Break-In Recommendations . . . . . . . . . . .69 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .69 11 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Manual Transmission 1. Turn the ignition switch to the ACC position. 2. Push the key and cylinder inward and rotate the key to the LOCK position. 3. Remove the key from the lock cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 3. Push the key and cylinder inward and rotate the key to the LOCK position 4. remove the key from the lock cylinder. Ignition Key Positions Automatic Transmission — If Equipped 1. Place the shift lever in PARK. 2. Turn the ignition switch to the ACC position.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speedpass™, additional Sentry Keys威, or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming If you have two valid Sentry Keys威, you can program new Sentry Keys威 to the system by performing the following procedure: 1. Cut the additional Sentry Key威 Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Disarm The Security Alarm System 1. Press UNLOCK on the RKE transmitter. 2 2. Starting the vehicle with a valid Sentry Key威 will disarm the Security Alarm. A valid key is one that is programmed to your vehicle. A valid key will disarm the Security Alarm System; an invalid key will allow the engine to run for two seconds and stop.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. To Lock The Doors And Liftgate Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lights will flash and the horn will chirp once to acknowledge the lock signal.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn Off “Flash Lights With Lock” NOTE: The “Flash Lights With Lock” feature can be turned on or off. On EVIC equipped vehicles refer to ⬙Personal Settings⬙ under “Electronic Vehicle Information Center (EVIC)” in Section 4. For vehicles not equipped with an EVIC, perform the following steps: 1. Press the UNLOCK button for four to 10 seconds. 2. While the UNLOCK button is pressed (after four seconds), press the LOCK button. Release both buttons. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Use the following procedure to program additional RKE transmitters if the vehicle is not equipped with Sentry Key威: entered program mode. All RKE transmitters that are to be programmed must be done so within 60 seconds of when the chime is heard. 1. Enter your vehicle and close all doors. 8. Using the RKE transmitter to be programmed, press and release both the LOCK and UNLOCK buttons simultaneously. 2.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed RKE transmitters function normally. NOTE: If you do not have a programmed RKE transmitter, contact your authorized dealer for details. General Information This device complies with Part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. If the RKE transmitter is equipped with a screw, remove the screw. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter apart. Make sure not to damage the elastomer seal during removal. 25 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. 2 Power Door Locks A power door lock switch is located on the drivers door panel. Press this switch to lock or unlock the doors.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h). 6. The doors were not previously locked using the power door lock switch or Remote Keyless Entry (RKE) transmitter. The Automatic Door Lock feature can be enabled or disabled. Refer to “Personal Settings” under “Electronic Vehicle Information Center (EVIC) — (if equipped)” in Section 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled. 29 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between LOCK and ON and back to LOCK four times, ending up in the LOCK position. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The drivers door is opened. 5.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the programming. NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws. Child-Protection Door Lock System (Rear Doors) — If Equipped Insert the tip of the ignition key into the lock and rotate to the LOCK or UNLOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Inserting Ignition Key NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down the window and open the door with the outside door handle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS — IF EQUIPPED Power Window Switches is a single open and close switch on each passenger door panel for passenger window control. The windows will operate only when the ignition switch is turned to the ON position, ACC position, and for up to 10 minutes after the ignition is turned OFF or the driver’s door is opened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCKOUT switch. To enable the window controls, press the window LOCKOUT switch a second time. Window Lockout Switch 33 LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, squeeze the liftgate release and pull the liftgate open with one fluid motion. NOTE: In the event of a power malfunction, or the RKE transmitter is inoperative, insert the key into the liftgate lock cylinder and turn to the right (manual lock models only). Using the liftgate handle, pull the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Gas props support the liftgate in the open position.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Pulling Out The Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! 41 Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 3. Route the shoulder belt to the inside of the right head restraint. 2 Routing The Rear Center Shoulder Belt Routing The Rear Center Shoulder Belt 4. When the belt is long enough to fit, insert the minilatch plate into the mini-buckle until you hear a “click.” 5. Sit back in the seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go around your lap.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Connecting Mini-Latch To Buckle 7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up Rear Center Seat Belt Buckled 8.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. To release the belt, push the red button on the buckle. 45 slide the latch plate down the webbing to allow the belt to retract fully. Insert the mini-latch plate into the slot provided in the trim panel. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to automatically remove any slack from the seat belts in the event of a collision.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Airbag Control Module (refer to information on Airbags in this section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver or front passenger seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. 2 This vehicle may also be equipped with side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • • • • • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and younger should ride buckled up in the rear seat. 2. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. 3.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Airbag System Components The airbag system consists of the following: • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direction provided by the ORC. This ORC will detect rollover.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Front Passenger Airbag/Inflator Units are located in the center of the steering wheel and the passenger side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates may be possible based on collision severity.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy when the ORC detects a moderate-to-severe collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following functions: • Cuts off fuel to the engine. • Flashes hazard lights.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data parameters (see list below) in an event data recorder prior to the moment of airbag deployment, or near-deployment, and up to a quarter second of high-speed deceleration data during and/or after airbag deployment or neardeployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler to any third party except when: 1.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status • Traction/stability control status • Tire pressure monitoring system status Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seatback; they should use a belt positioning booster seat. The child and booster seat are held in the vehicle by the lap/ shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE fixed lower attachments must be installed in the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage. If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 rearward-facing infant restraints will also be equipped with a tether strap with a hook and means for adjusting the tension in the strap. 2 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seatback.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 mi (500 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ Inside Day/Night Mirror — If Equipped . . . . . .78 ▫ Outside Mirror — Driver’s Side . . . . . . . . . . . .79 ▫ Outside Mirror — Passenger’s Side . . . . . . . . . .79 ▫ Folding Outside Mirrors — If Equipped . . . . . .80 ▫ Power Remote Control Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ Vanity Mirrors — If Equipped . . . . . . . . . . . . .
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 ▫ Front Seat Adjustment . . . . . . . . . . . . . . . . . . 109 ▫ Map/Reading Lights . . . . . . . . . . . . . . . . . . . 120 ▫ Manual Seat Height Adjustment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Multifunction Control Lever . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 䡵 Windshield Wipers And Washers . . . . . . . . . . . 127 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 133 ▫ Windshield Wiper Operation . . . . . . . . . . . . . 127 䡵 Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Intermittent Wiper System . . . . . . . . . . . . . . . 128 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 128 ▫ Mist Feature . . . . . . . . . . . . . . . . . . .
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . . . 147 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . 148 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 152 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 148 ▫ General Information . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . . 162 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . . 163 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . . 162 䡵 Roof Luggage Rack — If Equipped . . . . . . . . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the flat (driver’s side) outside mirror to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. 79 Outside Mirror — Passenger’s Side Adjust the convex (passenger’s side) outside mirror to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Outside Mirrors — If Equipped Power Remote Control Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Folding the Outside Mirrors The exterior mirrors are hinged and may be moved, manually, either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors — If Equipped To use the mirror, rotate the sun visor down and swing the mirror cover upward. Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass. HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER, REN and REU radios contain an integrated Hands-Free Communication (UConnect威) system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The UConnect威 system requires a cellular phone equipped with the Bluetooth威 ⬙Hands-Free Profile,⬙ Version 0.96 or higher. See the UConnect威 website for supported phones. NOTE: For UConnect威 customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Button The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (PHONE Button and VOICE RECOGNITION button) that will enable you to access the system. Voice Recognition Button Actual button location may vary with radio. The individual buttons are described in the “Operation” section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To complete the pairing process, you will need to reference your cellular phone Owner’s Manual. The UConnect威 website may also provide detailed instructions for pairing. • For identification purposes, you will be prompted to give the UConnect威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Dial by Saying a Number Call by Saying a Name • Press the PHONE button to begin. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • After the ⬙Ready⬙ prompt and the following beep, say “Call.⬙ • The system will prompt you to say the number you want to call. • The system will prompt you to say the name of the person you want to call. • For example, you can say ⬙234-567-8901.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect威 Phonebook NOTE: Adding names to the phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The phone handset must support Bluetooth威 OBEX transfers of phonebook entries to use this feature. • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the UConnect威 system, and then send the address book entry via Bluetooth威.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature. “Voice Recognition” button while the UConnect威 system is playing the desired entry and say ⬙Delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Note that only the phonebook in the current language is deleted. List All Names in the UConnect威 Phonebook • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect威 system will play the names of all the phonebook entries. • To call one of the names in the list, press the “Voice Recognition” button during the playing of the desired name, and say ⬙Call.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the PHONE button to place the current call on hold and answer the incoming call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the “Voice Recognition” button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can continue on the UConnect威 system for a certain duration, after which the call is automatically transferred from the UConnect威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect威 system will instruct the paired cellular phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the UConnect威 system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect威 system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from your UConnect威 paired cellular phone to the UConnect威 system or vice versa, press the “Voice Recognition” button and say ⬙Transfer Call.⬙ Connect or Disconnect Link Between the UConnect威 System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. 99 • When prompted, say ⬙List Phones.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect威 system will return to using the highest priority phone present in or near (approximately within 30 ft [9 m]) the vehicle. Delete UConnect威 Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Repeat the words and phrases when prompted by the UConnect威 system. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched OFF. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is not in motion is recommended. • It is not recommended to store similar sounding names in the UConnect威 phonebook. • The UConnect威 phonebook nametag recognition rate is optimized for the person who stored the name in the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth威 Communication Link Cellular phones have been found to lose connection to the UConnect威 system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth威 ON mode.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 107 3
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. 3 • This device must accept any interference received, including interference that may cause undesired operation. SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the ratcheting handle on the outboard side of the seat to adjust the driving position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Manual Lumbar — If Equipped The Lumbar adjustment is located on the outboard side of the driver’s seat. To increase or decrease support, rotate the handle up or down.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Seatback Recline To recline: 1. Lean forward before lifting the handle, then lean back to the desired position and release the handle. 2. Lift the handle to return the seatback to an upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, depress the button and push down on the head restraint.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped • Pressing the switch once will select HIGHlevel heating. WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: If HIGH-level heating is selected, heat will be felt within two to three minutes.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to move the seat forward and flat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Reclining Rear Seat — If Equipped 3 Folding Rear Seat Reclining The Rear Seat
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional comfort, pull the strap forward just enough to release the seatback latch. Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located on the left kick panel. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then move the safety catch located under the front edge of the hood, near the center and raise the hood. 119 To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Map/Reading Lights These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn the light OFF. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Control Lever The Multifunction Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The Multifunction Control Lever is located on the left side of the steering column.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multifunction Control Lever up or down. Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the shift lever is in any position except park.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped 123 NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals 3 Front Fog Lights Control The front fog light switch is on the Multifunction Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the Multifunction Control Lever.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. Highbeam/Lowbeam Select Switch If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by lightly pulling the Multifunction Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multifunction Control Lever is held in the flash-to-pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash-to-pass operation.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The auxiliary Off-Road lights can only be activated when the high beam headlights are on. Press the top of the switch to turn on the auxiliary Off-Road lights when off-road conditions require additional lighting. Press the bottom of the switch to turn off the auxiliary Off-Road lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Windshield Wiper Operation Turn the end of the handle to select the desired wiper speed.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the knob upward (clockwise) to decrease the delay time and downward (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Mist Control 129 CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the steering column, push down on the lever below the turn signal control lever. With one hand firmly on the wheel, move the steering column up or down as desired. Push the lever back up to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. Speed Control Location To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, pulling the speed control lever toward you “CANCEL”, normal braking, or clutch pressure while slowing the vehicle, will deactivate speed control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery. To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Anytime the ESP system is in the “Full Off” mode, ERM is disabled. Refer to “Electronic Stability Program (ESP)” for a complete explanation of the available ESP modes. WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HDC has the capability to sense terrain and will only activate when the vehicle is descending a hill. It will not activate on level ground. If desired, HDC can be fully deactivated by putting the vehicle into ESP “Full Off” mode. This is done by pressing and holding the ESP OFF button for five seconds. Refer to “Electronic Stability Program (ESP)” in this section of the manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, ESP applies the brake of the appropriate wheel to assist in counteracting the over-steer or under-steer condition • Over-steer - when the vehicle is turning more than appropriate for the steering wheel position.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP Operating Modes The ESP system has three available operating modes for 4WD equipped vehicles and two available operating modes for 2WD equipped vehicles. Full On (4WD Models) or On (2WD Models) This is the normal operating mode for ESP. Whenever the vehicle is started the ESP system will be in this “On” mode. This mode should be used for most driving situations. ESP should only be turned to “Partial Off” or “ESP Off” for specific reasons as noted below.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE will illuminate and the “ESP Off” message will appear in the odometer. Press and release the Trip Odometer button located on the instrument cluster to clear this message. In this mode, ESP is turned off until the vehicle reaches a speed of 35 mph (56 km/h). At 35 mph (56 km/h) the system returns to “Partial Off” mode, as described above. When the vehicle speed drops below 30 mph (48 km/h) the ESP system shuts off.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP/BAS Warning Light and ESP Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator. The yellow “ESP/BAS Warning Light” and the yellow “ESP Indicator Light” in the instrument cluster both come on when the ignition switch is turned to the ON position. They should both go out with the engine running.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons that are located in the head liner or the sun visor designate the three different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. 143 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink姞 Button To re-program a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Programming Homelink威 Step 2 and follow all remaining steps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located in the reading light. 1. This device may not cause harmful interference 3 2.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE held forward again. To ensure sunroof is fully closed, press and hold switch until sunroof has completely stopped moving. Express Mode Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, and stop automatically. This is called Express Close. During Express Close operation, any movement of the switch will stop the sunroof.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Ignition Off Operation Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! To Avoid Serious Injury or Death: • Do not use a Three-Prong Adapter. 3 • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use, and while driving the vehicle. • If this outlet is mishandled it may cause an electric shock and failure.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. Power Outlet — 115 Volts (150 Watts) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 CONSOLE FEATURES WARNING! Do not operate this vehicle with the console compartment lid in the open position. Cell phones, music players, and other hand-held electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. The floor console’s sliding armrest moves forward 3 in (76.2 mm) to accommodate shorter drivers.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Cargo Light/Removable Self Recharging Flashlight — If Equipped The dual-function light is mounted in the headliner above the cargo area to illuminate the cargo area, and part of it snaps out of the bezel to serve as a flashlight, when needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place for convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3 Removing Flashlight Three-Press Switch
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — If Equipped To cover the cargo area: 3. The liftgate may be opened or closed with the cargo cover in place. 1. Grasp the center portion of the cover flap. Pull it over the cargo area. Cargo Cover Removal WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Remove right side from cargo area. 4. Remove assembly from the vehicle. 159 Removable Load Floor The cargo area load floor is removable and can be washed with mild soap and water. For removal, lift the load floor with your finger at the space provided at the rear.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Loops There are four D-rings tie-down loops in the lower trim for securing cargo. The tie-downs located on the cargo area floor should be used to safely secure loads when vehicle is moving. WARNING! • Cargo tie-down Loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. Fold Down Speakers — If Equipped When the liftgate is open, the speakers can swing down from the trim panel to face rearward, for tailgating and other activities.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch forward to the ON position will activate the wiper. The rear wiper operates in an intermittent mode only. Rotating the center of the switch all the way forward will turn on the wash function. The wash pump will continue to operate as long as the button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements. ROOF LUGGAGE RACK — IF EQUIPPED External racks do not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CAUTION! WARNING! • To prevent damage to the roof of your vehicle, DO NOT Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack. carry any loads on the roof rack without cross rails installed.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . . 170 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 187 䡵 Instrument Cluster — Premium . . . . . . . . . . . . . 171 ▫ Elapsed Time . . . . . . . . . . . . . . . . . . . . . . . . 187 䡵 Instrument Cluster Descriptions . . . . . . . . . . . . 172 ▫ Tire Pressure Monitor (TPM) . . . . . . . . . . . . . 187 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . .
168 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 194 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 195 䡵 Sales Code REF — AM/FM/CD (Single-Disc) Radio With Optional Satellite Radio And Hands-Free Phone Capability . . . . . . . . . . . . . . 195 ▫ Operating Instructions - Radio Mode . . . . . . . 196 ▫ Operating Instructions - CD Mode . . . . . . . . . 199 ▫ Operating Instructions - Auxiliary Mode . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REC — AM/FM/CD (6–Disc) Radio With Navigation System . . . . . . . . . . . . . 217 ▫ Operating Instructions — Satellite Radio — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 217 ▫ REC Setting The Clock . . . . . . . . . . . . . . . . . 218 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 220 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 220 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . .
170 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlet — Demisters — Instrument Cluster — Radio 5 6 7 8 — — — — Glove Box Storage Bin Climate Controls Heated Seat Switches — If Equipped 9 — Hazard Warning Flasher 10 — ESP OFF Switch — If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 171 INSTRUMENT CLUSTER — PREMIUM 4
172 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge/Fuel Door Location When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Voltage Warning Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. Oil Pressure Warning Light Shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the light does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut OFF the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED.
174 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Anti-Lock Brake Warning Light — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Engine Coolant Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 14. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application.
176 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with Anti-Lock Brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Temperature Gauge If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the engine off immediately and call for service. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off.
178 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
180 UNDERSTANDING YOUR INSTRUMENT PANEL U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. Change Oil Message Your vehicle is equipped with an engine oil change indicator system.
UNDERSTANDING YOUR INSTRUMENT PANEL 26. Malfunction Indicator Light (MIL) This light is part of an Onboard Diagnostic system called OBD II that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the light does not come on when turning the key from OFF to ON/ RUN, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
182 UNDERSTANDING YOUR INSTRUMENT PANEL 30. Electronic Stability Program (ESP) Indicator Light The malfunction light for the ESP is combined with BAS. The yellow “ESP/BAS Warning Light” comes on when the ignition switch is turned to the ON position. They should go out with the engine running. If the “ESP/BAS Warning Light” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED 183 • Vehicle information warning message displays • Personal settings (customer-programmable features) • Compass heading • Outside temperature display • Trip computer functions • UConnect威 hands-free communication system displays (if equipped) • Audio mode display • Tire Pressure Monitor (TPM) EVIC Location When the appropriate conditions exist, the EVIC displays the following messages: The Electronic Vehic
184 UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Turn Signal Light Out (with a single chime) • Right Rear Turn Signal Light Out (with a single chime) • RKE Battery Low (with a single chime) • Personal Settings Not Available – Vehicle not in PARK (automatic transmissions) or vehicle is in motion (manual transmissions).
UNDERSTANDING YOUR INSTRUMENT PANEL cluster. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure. 185 EVIC Functions 1. Turn the ignition switch to the ON position. Do not start the engine. 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 4 3. Turn the ignition switch to the OFF/LOCK position.
186 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Compass/Temperature/Audio • Elapsed Time Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside temperature and the current radio station. • Tire Pressure Monitor (TPM) • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the function currently being displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value.
188 UNDERSTANDING YOUR INSTRUMENT PANEL Use the EVIC button to display one of the following choices: Language When in this display you may select different languages for all display nomenclature, including the trip functions. Pressing the EVIC button while in this display selects English, Espanol, Deutsch, Italiano, or Francais depending on availability. As you continue, the displayed information will be shown in the selected language. NOTE: UConnect威 language will not change using the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when the RKE transmitter LOCK button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Press and hold the EVIC button when in this display until “ON” or “OFF” appears to make your selection.
190 UNDERSTANDING YOUR INSTRUMENT PANEL Delay Power Off to Accessories Until Exit When this feature is selected the power window switches, radio, hands–free system, power sunroof, and power outlets will remain active for up to 60 minutes after the ignition switch has been turned OFF. Opening a vehicle door will cancel this feature. Press and hold the EVIC button when in this display until “OFF”, “45 sec.”, “5 min.”, or “10 min.” appears to make your selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. In order to ensure compass accuracy, the Compass Variance should be set to the zone number on the Compass Variance map that corresponds to the current location of the vehicle.
192 UNDERSTANDING YOUR INSTRUMENT PANEL To Set the Variance With the ignition in the ON position, quickly (less than one second) press and release the EVIC button several times until you have displayed the Personal Settings (Customer-Programmable Features) menu. Once in the Personal Settings (Customer-Programmable Features) menu, press and release (less than one second) the EVIC button several times until “Compass Variance” is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL EVIC button will place the Compass in calibration mode. The Cal indicator will come on continuously in the EVIC display, to indicate that the compass is now in the calibration mode and that the vehicle can now be driven to calibrate. A short EVIC button press from the ⬙Calibrate Compass (Yes)⬙ screen will exit the EVIC Customer Programmable features, and return it to its normal operating mode.
194 UNDERSTANDING YOUR INSTRUMENT PANEL TWO TYPES OF SIGNALS There are two basic types of radio signals: AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary; and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO control knob. 195 SALES CODE REF — AM/FM/CD (SINGLE-DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS-FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. 3. After the hours are adjusted, push the TUNE/AUDIO control knob to set the minutes. 4 4.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In Hands-Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
198 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Radio Mode) Turn the rotary TUNE control clockwise to increase or counterclockwise to decrease the frequency. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. AM/FM Button (Radio Mode) Press the button to select AM or FM modes. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
200 UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD player. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • This radio does not play discs with MP3 tracks. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature. If the RW button is pressed, the current track will reverse to the beginning of the track and begin playing. RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
202 UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning off the ignition will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of this Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS-FREE PHONE, AND VIDEO ENTERTAINMENT SYSTEM (VES™) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
204 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
206 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control, and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Program Type Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft
208 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - (CD Mode for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
210 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD Mode for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD Mode for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
212 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press the RND button a second time to stop Random play. Buttons 1 - 6 (CD Mode for CD Audio Play) Selects disc positions 1 - 6 for Play/Load/Eject.
UNDERSTANDING YOUR INSTRUMENT PANEL • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player. in the radio, the radio will remain in CD mode and display ⬙INSERT DISC” for two minutes. After two minutes the radio will go to the previous tuner mode. Radio display will show ⬙LOADING DISC⬙ when the disc is loading. MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc.
216 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (CD Mode for MP3 Play) Pressing the TUNE control allows the adjustment of Tone, Balance, and Fade. AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM 217 menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America. Refer to your “Navigation User’s Manual” for detailed operating instructions.
218 UNDERSTANDING YOUR INSTRUMENT PANEL REC Setting the Clock GPS Clock The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellites. The satellites’ clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 4. To turn daylight savings on or off, select “Daylight Savings” and press ENTER. Select “On” or “Off” and press ENTER. 5. Select DONE to exit from the clock setting mode. Press ENTER to save your changes. If you press CANCEL or NAV then your changes will not be saved. 4 User Defined Clock If you wish to set the clock to a time different than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option. 1.
220 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To decrease the clock by one hour, use the Select Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4. To increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER. Press ENTER again to increase the clock by another minute. 5. To decrease the clock by minutes, use the Select Encoder to highlight the “-“ sign. Press ENTER. Press ENTER again to decrease the clock by another minute. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number. To access the ESN/SID, refer to the following procedure.
222 UNDERSTANDING YOUR INSTRUMENT PANEL With the ignition in the ACC position and the radio off, press the CD Eject and SET buttons simultaneously until the 12 digits of the ESN/SID appear on the screen. Selecting Satellite Mode in REF, RAQ, And RAK Radios Selecting Satellite Mode — REF Radio Press the MODE button repeatedly until the word ⬙SAT⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Storing And Selecting Preset Channels In addition to the 12 AM and 12 FM preset stations, you may also commit 12 satellite stations to pushbutton memory. These satellite channel preset stations will not erase any AM or FM preset memory stations. Follow the memory preset procedures that apply to your radio. Using The PTY (Program Type) Button — If Equipped Follow the PTY button instructions that apply to your radio.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 The left-hand control is a rocker type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. CD Player Press the top of the switch once to go to the next track on the CD. The following describes the left-hand control operation in each mode.
226 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If a disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching a disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store a disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Climate Controls The Climate Control System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Climate Control Location 227 The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demister outlets with a small amount through the defrost outlet.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear seat passengers, the center instrument panel outlets can be aimed, so that the left center outlet is directed toward the right rear passenger and the right center outlet is directed toward the left rear passenger. Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control from left (OFF) to right.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in recirculate mode. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL MAX A/C For maximum cooling select the air direction to either the Panel or Bi-Level position using the mode control. Press the A/C button and the recirculation button so that both lamps are illuminated and set the temperature control to its coolest setting. NOTE: • Recirculation Mode will not operate in floor, mix or defrost modes. • See “Circulation Control” in this section, for proper or extended use of this position.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, set mode to the mix or defrost position. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur. Interior fogging on the windshield can be quickly removed by using the defrost position. If the fogging problem persists, clean the inside window surfaces.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 239 䡵 Manual Transaxle — If Equipped . . . . . . . . . . . 242 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 239 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 243 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 239 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . .
236 STARTING AND OPERATING 䡵 AutoStick威 — If Equipped . . . . . . . . . . . . . . . . 249 ▫ Simultaneous Brake And Throttle Operation . . 260 ▫ AutoStick威 Operation . . . . . . . . . . . . . . . . . . 249 ▫ Driving In Snow, Mud And Sand . . . . . . . . . . 260 ▫ AutoStick威 General Information . . . . . . . . . . . 250 ▫ Crossing Obstacles (Rocks And Other High Points) . . . . . . . . . . . . . . . . . . . . . . . . . 262 䡵 Four-Wheel Drive Operation — If Equipped . . . .
STARTING AND OPERATING 237 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Premium System — If Equipped . . . . . . . . . . 306 ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ General Information . . . . . . . . . . . . . . . . . . . 310 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 282 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 283 ▫ Tire Markings . . . . . . . . . . . . . . . . . . .
238 STARTING AND OPERATING ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 316 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 322 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 317 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 323 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . . 317 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 327 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
240 STARTING AND OPERATING Normal Starting Normal starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the START position and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the OFF position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “Normal Starting” procedure.
242 STARTING AND OPERATING MANUAL TRANSAXLE — IF EQUIPPED WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. 5-Speed Shift Pattern Use each gear in numerical order, do not skip a gear.
STARTING AND OPERATING 243 For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended. Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in the following table. Never drive with your foot resting on the clutch pedal, and never try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch.
244 STARTING AND OPERATING CAUTION! AUTOMATIC TRANSAXLE — IF EQUIPPED If you skip more than one gear while downshifting or downshift at too high a vehicle speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st gear when descending a steep grade. When turning a corner or driving up a steep grade, downshift early so that the engine will not be overburdened.
STARTING AND OPERATING 245 CAUTION! NOTE: You MUST press and hold the brake pedal down while shifting out of PARK. Damage to the transaxle may occur if the following precautions are not observed: WARNING! • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
246 STARTING AND OPERATING Brake/Transmission Interlock System This system prevents you from moving the shift lever out of PARK and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the shift lever out of PARK. NOTE: If a malfunction occurs, the transaxle will not shift out of PARK. Battery power is required to release the brake/transmission interlock system.
STARTING AND OPERATING PARK Supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the shift lever in the PARK position. 247 WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
248 STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the transmission shift lever into the PARK position: REVERSE Shift into this range only after the vehicle has come to a complete stop. • When shifting into PARK, firmly move the shift lever all the way forward until it stops. NEUTRAL The engine may be started in this range. • Look at the shift indicator window on the shift lever bezel to ensure it is in the PARK position.
STARTING AND OPERATING AUTOSTICK姞 — IF EQUIPPED Autostick威 is a driver-interactive transmission that offers six manual ratio changes to provide you with more control. Autostick威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
250 STARTING AND OPERATING Autostick威 operation is activated in the DRIVE position by moving the shift lever side-to-side. Moving the shift lever to the (+) side will activate Autostick威 and shift up to the next higher manual ratio, unless you are already operating in or near Overdrive, in which case 6th ratio will be selected. In like manner, moving the shift lever to (-) will activate Autostick威 and shift to the next lower manual ratio.
STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED This feature provides full time, on-demand, 4–Wheel Drive (4WD). 251 Where one or more wheels have wheel spin or if additional traction is needed in sand, deep snow, or loose traction surfaces, activate the 4WD Lock switch by pulling up once and releasing. This locks the center coupling allowing more torque to be sent to the rear wheels. The amber 4WD Indicator Light will come on in the cluster.
252 STARTING AND OPERATING FREEDOM DRIVE II – SAFE OFF-ROAD DRIVING Off-Road Driving Tips and Vehicle Characteristics The Freedom Drive II Off-Road Package has excellent on and off-road capabilities. These off-road capabilities will allow you to explore those wilderness trails where few travel, providing a source of exciting and satisfying recreation.
STARTING AND OPERATING • Unique springs for a 1 in (2.
254 STARTING AND OPERATING Freedom Drive II – Off-Road Features The following are key off-road features which are active when the system has the 4WD lock lever engaged and is in the Low Off-Road mode. • Hill Descent Braking – Hill descent braking uses the vehicle braking system to provide a controlled descent down varying grades. This feature is only active when the system has the 4WD lock lever engaged and is in the Low Off-Road mode or reverse. Hill descent braking can be turned off by turning off ESP.
STARTING AND OPERATING • Unique Engine Calibration – When the system has the 4WD lock lever engaged and is in the Low Off-Road mode or reverse, the engine calibration changes to run higher spark advance with premium fuel for optimum off-road performance. Your vehicle is equipped with an active spark knock system and can adjust the engine calibration for a varying range of fuel octane levels.
256 STARTING AND OPERATING Angles A B C D
STARTING AND OPERATING Water Fording Characteristics Water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion. The Freedom Drive II Off-Road package has high water fording characteristics with the ability to cross a pool of water, 257 without stopping, 19 in (48 cm) deep at a maximum speed of 5 mph (8 km/h) with an entrance ramp angle of 1.3 degrees.
258 STARTING AND OPERATING Water Fording Characteristics
STARTING AND OPERATING The Basics of Off-Road Driving You will encounter many types of terrain driving offroad. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different effect on your vehicle’s steering, handling and traction.
260 STARTING AND OPERATING When To Use Low (L Off-Road) with the 4WD Lock Lever Engaged When driving off-road, shift into low (L Off-Road) and activate the 4WD LOCK. This will provide additional traction and activates the numerous off-road features to improve handling and control on slippery or difficult terrain. Due to the sustained lower gearing, low (L Off-Road) with 4WD Lock engaged will allow the engine to operate in a higher power range.
STARTING AND OPERATING CAUTION! On icy or slippery roads, do not downshift at high engine RPM’s or vehicle speeds because engine braking may cause skidding and loss of control. • Mud – Deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use low (L Off-Road) with the 4WD LOCK engaged and maintain your momentum. If you start to slow to a stop, try turning your steering wheel no more than a 1/4 turn quickly back and forth for additional traction.
262 STARTING AND OPERATING CAUTION! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers. Crossing Obstacles (Rocks And Other High Points) While driving off-road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles.
STARTING AND OPERATING Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. CAUTION! Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.
264 STARTING AND OPERATING Crossing Logs To cross a log, approach it at a slight angle (approximately 10 to 15 degrees). This allows one front tire to be on top of the log while the other just starts to climb the log. While climbing the log, modulate your brake and accelerator to avoid spinning the log out from under your tires. Then ease the vehicle off the log using your brakes. what is the best direction to recover the vehicle.
STARTING AND OPERATING feel confident with the vehicle and your abilities. You should always climb hills straight up and down. Never attempt to climb a hill on an angle. • Before Climbing A Steep Hill – As you approach a hill consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail.
266 STARTING AND OPERATING WARNING! Never attempt to climb a hill at an angle or turn around on a steep grade. Driving across an incline increases the risk of a rollover, which may result in severe injury. • Driving Down Hill – Before driving down a steep hill you need to determine if it is too steep for a safe descent.
STARTING AND OPERATING 267 WARNING! WARNING! Driving across an incline increases the risk of a rollover, which may result in severe injury. If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in REVERSE gear. Never back down a hill in NEUTRAL using only the vehicle brakes.
268 STARTING AND OPERATING Driving Through Water Extreme care should be taken crossing any type of water. Water crossings should be avoided if possible, and only be attempted when necessary in a safe responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicles abilities and be able to recover it if something goes wrong.
STARTING AND OPERATING • Before You Cross Any Type Of Water – As you approach any type of water you need to determine if you can cross it safely and responsibly. If necessary, get out and walk through the water or probe it with a stick. You need to be sure of its depth, approach angle, current and bottom condition. Be careful of murky or muddy waters, check for hidden obstacles. Make sure you will not be intruding on any wildlife and you can recover the vehicle if necessary.
270 STARTING AND OPERATING • Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water – Flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water. Fast moving water can easily push your vehicle downstream sweeping it out of control. Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.
STARTING AND OPERATING softer surfaces such as sand and lighter vehicles. You will need to experiment to determine what is right for your situation. It is easier and faster to let air out than it is to replace it so, start high and lower it as required. Remember you must return the tires to normal air pressure before driving on-road or at highway conditions. Be sure you have a way to return the tires to their normal on-road air pressure.
272 STARTING AND OPERATING surroundings, then using a tow strap to the vehicle tow hooks would be fast and easy. If the vehicle is severely hung up or in a situation where great care needs to be taken during the recovery, then nothing can do the job better than a winch. If you are severely hung up on something you should jack the vehicle up and stack something under the wheels to allow the vehicle to roll off the object without causing further damage.
STARTING AND OPERATING CAUTION! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 30 mph (48 km/h). Do not spin the wheels continuously for more than 30 seconds. • Using The Tow Hooks With A Tow Strap – Tow straps are a quick and easy way to recover your vehicle from minor situations if you have a secondary vehicle which is not stuck. The tow hooks on your vehicle are designed to take the abusive force generated during vehicle recovery.
274 STARTING AND OPERATING WARNING! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than 2 to 3 ft (61 to 91 cm) of slack in the strap. More slack than this greatly increases the risk of injury and vehicle damage. Always keep everyone at least 30 ft (9 m) away from a strapping or winching situation.
STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. Failure to do so may result is serious injury.
276 STARTING AND OPERATING TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
STARTING AND OPERATING brake pedal, pull up slightly on the lever, then depress the button on the end of the lever and push the lever fully down toward the floor. NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position.
278 STARTING AND OPERATING WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light. WARNING! Driving a vehicle with the brake light on is dangerous.
280 STARTING AND OPERATING WARNING! • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 281 When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self-check cycle to ensure that the ABS working properly. This self-check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). • a slight drop or fall away of the brake pedal at the end of the stop ABS is activated during braking under certain road or stopping conditions.
282 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING TIRE SAFETY INFORMATION TIRE MARKINGS 283 • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H. • LT (Light Truck) - Metric tire sizing is based on U.S. design standards.
284 STARTING AND OPERATING Tire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 285 TIRE SIZING TERMS Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
286 STARTING AND OPERATING TIRE IDENTIFICATION NUMBER (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING TIRE LOADING AND TIRE PRESSURE 287 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar.
288 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
290 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 291 1. Safety— WARNING! •Improperly inflated tires are dangerous and can cause accidents. •Under-inflation increases tire flexing and can result in tire failure.
292 STARTING AND OPERATING WARNING! •Unequal tire pressures can cause steering problems. You could lose control of your vehicle. •Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. •Always drive with each tire inflated to the recommended cold tire inflation pressure. 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread.
STARTING AND OPERATING 293 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire Placard Location The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure.
294 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature = 68°F (20°C) and the outside temperature = 32°F (0°C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.
STARTING AND OPERATING Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
296 STARTING AND OPERATING DO NOT install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. DO NOT install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, DO NOT take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, DO NOT spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. 297 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. For additional information, refer to “Freeing A Stuck Vehicle” in Section 6. WARNING! Fast spinning tires can be dangerous.
298 STARTING AND OPERATING Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 299 WARNING! WARNING! DO NOT use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
300 STARTING AND OPERATING Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your authorized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance.
STARTING AND OPERATING type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible, if desired. The reason(s) for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram below.
302 STARTING AND OPERATING pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure. vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. • The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
304 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Base System — If Equipped This is the TPMS warning indicator located in the instrument cluster. The TPMS uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module.
STARTING AND OPERATING The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists. A system fault can occur with any of the following scenarios: 1.
306 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will sound and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid. NOTE: It is particularly important for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. 5.
STARTING AND OPERATING 307 Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for each condition that it detects. In addition, the EVIC will display a graphic of the pressure value(s) with the low tire(s) flashing.
308 STARTING AND OPERATING graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. Check TPMS Message The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime.
STARTING AND OPERATING will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors.
310 STARTING AND OPERATING limit in any of the four active road tires. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
STARTING AND OPERATING FUEL REQUIREMENTS GASOLINE ENGINES Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high-quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high-quality regular gasolines and, in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine.
312 STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol.
STARTING AND OPERATING Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
314 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period of time.
STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. 315 CAUTION! • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
316 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. • Never add fuel when the engine is running. This is in violation of most state and Federal fire regulations and will cause the Malfunction Indicator Light (MIL) to turn on.
STARTING AND OPERATING the vehicle is started. Refer to “Onboard Diagnostic System — OBD II” in Section 7 of this manual for more information. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. VEHICLE LOADING Vehicle Loading Capacities: Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . .
318 STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
STARTING AND OPERATING Tongue Weight (TW) The Tongue Weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The frontal area is the maximum height and maximum width of the front of a trailer.
320 STARTING AND OPERATING WARNING! An improperly adjusted weight-distributing hitch system may reduce handling, stability, and braking performance, and could result in an accident. Weight-Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 321 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 2.4L Auto/Man 22 sq ft (2.04 sq m) 2.4L Auto/Man with Trailer Tow Prep Pack32 sq ft (3.0 Sq. m) age (AHC) Refer to local laws for maximum trailer towing speeds.
322 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely from side-toside which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
324 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
326 STARTING AND OPERATING CAUTION! WARNING! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
STARTING AND OPERATING 327 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 5 7-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
328 STARTING AND OPERATING Towing Tips — Automatic Transmission The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. Refer to the “Maintenance Schedule” in Section 8 for transmission fluid change intervals. NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads.
STARTING AND OPERATING 329 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
330 STARTING AND OPERATING CAUTION! • DO NOT FLAT TOW any vehicle equipped with an AUTOMATIC TRANSAXLE. Damage to the drivetrain will result. If these vehicles require towing, make sure all four wheels are off the ground. • Front or rear wheel lifts should not be used. Internal damage to the transaxle will occur if a front or rear wheel lift is used when recreational towing.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 332 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 336 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 332 䡵 Jump-Starting Procedures Due To A Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 340 䡵 Automatic Transaxle Overheating . . . . . . . . . . . 333 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 334 ▫ Jack Location . . . . . . . . . . . . . . . .
332 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off. Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to HIGH. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H”, pull over when safe and stop the vehicle with the engine at idle.
334 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! Jack Location The jack and jack-handle are stowed under the load floor in the cargo area. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
WHAT TO DO IN EMERGENCIES Spare Tire Stowage The spare tire is stowed under the rear load floor in the cargo area. Spare Tire Removal Lift up the load floor cover and remove the hold down. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the shift lever in PARK (automatic transmission) or REVERSE (manual transmission). Turn OFF the ignition.
336 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Jack Warning Label • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • • Block the wheel diagonally opposite the wheel to be raised. • • • • Set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse.
WHAT TO DO IN EMERGENCIES 337 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. 6 Jacking Locations CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3.
338 WHAT TO DO IN EMERGENCIES 3. There are two front jacking locations and two rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts. For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locations in the body. Do not raise the vehicle until you are sure the jack is securely engaged. 4.
WHAT TO DO IN EMERGENCIES 339 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is 100 ft lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your authorized dealer or at a service station. 9. Remove the wheel blocks and lower the jack until it is free.
340 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way and may be damaged.
WHAT TO DO IN EMERGENCIES WARNING! Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. NOTE: Disconnecting the battery with the ignition in the ON position will cause vehicles with an automatic transaxle (CVT2) to go into “default mode” and turn on the Malfunction Indicator Light (MIL). See your authorized dealer to correct this condition. 1.
342 WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over the battery when attaching the clamps or allow the clamps to touch each other. If acid splashes in your eyes or on your skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES front wheels. Then shift back and forth between REVERSE and 1st gear. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause axle, tire damage or failure. A tire could explode and injure someone.
344 WHAT TO DO IN EMERGENCIES 2All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the ACC position, not in the LOCK position. Do not attempt to use sling type equipment when towing. When securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — Gasoline . . . . . . . . . . . 348 ▫ Drive Belt — Check Condition . . . . . . . . . . . . 356 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 349 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 356 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 349 ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 356 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
346 MAINTAINING YOUR VEHICLE ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 362 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 363 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 363 ▫ Windshield Washer Fluid Reservoir . . . . . . . . 364 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 364 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 365 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 370 ▫ Fuel System Connections . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 347 ▫ Auxiliary Off-Road Light . . . . . . . . . . . . . . . . 393 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 395 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . .
348 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — GASOLINE
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
350 MAINTAINING YOUR VEHICLE RESET button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of this vehicle’s emissions control system.
MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition key or start the engine.
352 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. 353 Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick.
354 MAINTAINING YOUR VEHICLE Change Engine Oil Refer to the “Maintenance Schedule” in Section 8 for recommended engine oil change intervals. Engine Oil Selection (Gasoline Engines) For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 355 Lubricants which do not have both the engine oil certification mark and the correct SAE viscosity grade number should not be used. authorized dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed.
356 MAINTAINING YOUR VEHICLE Drive Belt — Check Condition Check the drive belt condition. Refer to the “Maintenance Schedule” in Section 8 of this manual. Inspect the drive belt for evidence of cuts, cracks, or glazing and replace the belt for any sign of damage which could result in belt failure. The belt is self-tensioning and will not need adjustment. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control.
MAINTAINING YOUR VEHICLE 357 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
358 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected for a prolonged period. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits.
MAINTAINING YOUR VEHICLE 359 WARNING! CAUTION! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. When servicing the battery, always reinstall the battery thermowrap.
360 MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. 361 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
362 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit. After lubricating, excess oil and grease should be removed.
364 MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement 1. Lift the wiper arm away from the glass. 2. Push the release tab and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
366 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill Refer to “Maintenance Schedule” under Section 8. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection Of Coolant Refer to “Fluids, Lubricants and Genuine Parts” in Section 8.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
368 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator.
370 MAINTAINING YOUR VEHICLE • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” under Section 8. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
372 MAINTAINING YOUR VEHICLE NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and at every engine oil change. WARNING! fluid reservoir. Fluid level can be expected to fall as the brake pads wear. The brake fluid level should be checked when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed.
MAINTAINING YOUR VEHICLE 373 WARNING! WARNING! Use of a brake fluid that may have a lower initial boiling point or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. CAUTION! Use of improper brake fluids will affect overall clutch system performance.
374 MAINTAINING YOUR VEHICLE steel belt traction on the drive and driven pulleys. Refer to “Fluids, Lubricants and Genuine Parts” for correct fluid type. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid will cause belt slip and result in a complete transmission failure! Refer to “Fluids, Lubricants, and Genuine Parts” for correct fluid type. Fluid Level Check The fluid level in the automatic transaxle should be checked only by a trained technician.
MAINTAINING YOUR VEHICLE Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary lubricant has become contaminated with water. NOTE: If contaminated with water, the fluid should be changed immediately. Rear Drive Assembly (RDA) – AWD/4WD Models Only Lubricant Selection Use only the manufacturer’s recommended fluid.
376 MAINTAINING YOUR VEHICLE the fill plug. The fluid level should be maintained between the bottom of the fill hole to 1/8 in (4 mm) below the fill hole. hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. Add fluid, if necessary, to maintain the proper level. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, use Mopar威 Super Kleen Bug and Tar Remover to remove. • Use Mopar威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
378 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE • For grease stains, apply Mopar威 Multi-purpose Cleaner to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentials威 products. Interior Care Use Mopar威 Total Clean to clean fabric upholstery and carpeting. Use Mopar威 Total Clean to clean vinyl upholstery. Mopar威 Total Clean is specifically recommended for leather upholstery.
380 MAINTAINING YOUR VEHICLE Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and, therefore, different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
MAINTAINING YOUR VEHICLE Instrument Panel Bezels CAUTION! When installing hanging air fresheners in your vehicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1.
382 MAINTAINING YOUR VEHICLE FUSES/INTEGRATED POWER MODULE (IPM) An Integrated Power Module (IPM) is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “Engine Compartment” in this section of the Owner’s Manual for the underhood location of the IPM.
MAINTAINING YOUR VEHICLE Cavity Cartridge MiniFuse Fuse 13 20 Amp Yellow 14 10 Amp Red 15 40 Amp Green 16 15 Amp Lt Blue 17 10 Amp Red 18 40 Amp Green 19 20 Amp Yellow 20 15 Amp Lt Blue Description Pwr run/Acc Outlet RR IOD CCN/ Interior Lighting RAD Fan Relay Battery Feed IGN Run/Acc Cigar Ltr/Sunroof IOD Feed Mod-Wcm ASD Relay Contact PWR Feed PWR Amp 1 & Amp 2 Feed IOD Feed Radio Cavity Cartridge MiniFuse Fuse 21 10 Amp Red 22 10 Amp Red 23 15 Amp Lt Blue 24 15 Amp Lt Blue 25 10 Amp Red 26 15 Amp Lt B
384 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 29 30 20 Amp Yellow 10 Amp Red 31 32 33 MiniFuse 30 Amp Pink 10 Amp Red Description Hot Car (No Fuse Required) Heated Seats Headlamp Washer Relay Control ENG ASD Control Feed 1 ABS MOD/J1962 Conn/PCM Cavity Cartridge MiniFuse Fuse 34 30 Amp Pink 35 40 Amp Green 36 30 Amp Pink 37 25 Amp Natural Description ABS Valve Feed ABS Pump Feed Headlamp/Washer Control/Smart Glass 110 Inverter
MAINTAINING YOUR VEHICLE CAUTION! • When installing the IPM cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the IPM, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
386 MAINTAINING YOUR VEHICLE LIGHTS BULBS — Exterior Bulb No. Low Beam/High Beam Headlight . . . . . . . . . . . . H13 Front Park/Turn Signal/Side Marker Light . . . . . . . . . . . . . . . . . . 3157AK or 3157A Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . 9145 Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . LED Assembly Rear Tail/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . 3157 Rear Turn Signal . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2. Reach into engine compartment and pull red lock out at connector. 387 3. Remove the green connector from the back of the bulb by pulling straight back.
388 MAINTAINING YOUR VEHICLE 4. Twist the bulb to the left and pull outward from assembly. Removing Halogen Bulb From Assembly Twisting Bulb From Socket NOTE: These are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life.
MAINTAINING YOUR VEHICLE 389 Fog Lights See your authorized dealer for replacement. Tail Lights, Rear Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing.
390 MAINTAINING YOUR VEHICLE 2. Grasp the tail light and pull firmly to disengage the light from the aperture panel. 3. Twist and remove socket from the lightl.
MAINTAINING YOUR VEHICLE 4. Remove bulb from socket and replace. 391 License Lights 1. Use a screw driver to gently pry against the side of the snap tab to remove the light from the liftgate.
392 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1/4 turn counterclockwise. Removing Bulb From Socket Removing Socket From Lamp 3. Pull the bulb from the socket. Center High-Mounted Stoplight Light is an LED assembly. See your authorized dealer for replacement.
MAINTAINING YOUR VEHICLE Auxiliary Off-Road Light 1. Remove the three screws attaching the lens to the housing. 393 2. Unlatch the wire clasp securing the bulb into the housing and rotate it into the position shown.
394 MAINTAINING YOUR VEHICLE 3. Disconnect the bulb from the light harness to replace the bulb.
MAINTAINING YOUR VEHICLE 395 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter All Gasoline Engines (use API Certified SAE 5W-20 Engine Oil) Cooling System * Mopar威 Antifreeze/Coolant 5 Year/100,000 Miles Formula), or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. U.S. 13.5 Gal Metric 51.0 L 4.5 qts 4.26 L 7.2 qts 6.
396 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants And Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Mopar威 04884900AB or equivalent. ZFR5F-11 (Gap 0.
MAINTAINING YOUR VEHICLE 397 Chassis Component Automatic Transaxle (CVT) Fluid Manual Transaxle Fluid Rear Drive Assembly (RDA) Power Transfer Unit (PTU) Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants And Genuine Parts Mopar威 CVTF + 4 Mopar威 ATF+4 MS9602 Mopar威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent nonsynthetic product. Mopar威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent nonsynthetic product. Mopar威 DOT 3, SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . . 400 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 400 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 400 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Control System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 401 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change and even if the oil change indicator message is NOT illuminated.
M A I N T E N A N C E S C H E D U L E S 8 402 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • Check all lights and other electrical items for correct operation. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 403 M Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for dusty or off-road conditions, inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Replace the air conditioning filter. Inspect the CV Joints.
M 404 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Change the manual transmission fluid if using your vehicle C for any of the following: trailer towing, snow plowing, E heavy loading, taxi, police, delivery service (commercial S C H E D U L E S 8 service), off-road, desert operation or more then 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). Change Rear Drive Assembly (RDA) fluid. Change Power Transfer Unit (PTU) fluid.
MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . 409 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 411 ▫ Prepare For The Appointment . . . . . . . . . . . . 409 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . . 411 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 409 䡵 Warranty Information (U.S. Vehicles Only) . . . . .
408 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 414 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 415 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 416 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
410 IF YOU NEED CONSUMER ASSISTANCE high quality service. The manufacturer’s authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. • Owner’s telephone number (home and office) This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-4568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
412 IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience.
IF YOU NEED CONSUMER ASSISTANCE MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from an authorized dealer. They will help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
414 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals (no P.O. Boxes).
IF YOU NEED CONSUMER ASSISTANCE Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
416 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
418 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 279 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 367 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 163 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 313 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 358 Air Conditioner Maintenance . . . . . . . . . . . . . . . 361 Air Conditioning Controls . . . . . . . . . . . . . .
INDEX Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359 Keyless Transmitter Replacement (RKE) . . . . . . . 24 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 Body Mechanism Lubrication . . . . . . . . . . . . . . . 363 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 287 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 135 Brake Fluid . . . . . . . . .
420 INDEX Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . 69 CD (Compact Disc) Player . . . . . . . . . . . . . . . 195,203 CD (Compact Disc) Player Maintenance . . . . . . . . 226 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 82,226 Center High Mounted Stop Light . . . . . . . . . . . . 392 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 334 Chart, Tire Sizing . . . . . . . . . . . .
INDEX Pressure Cap . . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Corrosion Protection . . . . . . . . . . Crankcase Emission Control System Cruise Light . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . .... .... .... ... .... .... .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 366 376 358 177 155 409 Data Recorder, Event . . . . . . . . . . . . . . . . .
422 INDEX Electronic Stability Program (ESP) . . . . . . . . . . . . 138 Electronic Vehicle Information Center (EVIC) . . . . 183 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 340 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Emission Control System Maintenance . . . . . . 350,400 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 395 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 374 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 396 Fog Lights . . . . . . . . . . . . . . . . . . . . . . .
424 INDEX Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 312 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 177 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 General Information . . . . . . . . . . . . . . . . .
INDEX Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 172 Instrument Panel and Controls . . . . . . . . . . . . . . 170 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 380 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 381 Integrated Power Module (Fuses) . . . . . . . . . . . . 382 Interior Appearance Care . . . . . . . . . . . . . . . . . . 379 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 128 Introduction . . . . . . . . . . . . . . . . . . . . . . . . .
426 INDEX Daytime Running . . . . . . . . . . . . . . . . . . . . . . 122 Dimmer Switch, Headlight . . . . . . . . . . . . . . . 121 Electronic Stability Program (ESP) Indicator . . . . . . . . . . . . . . . . . . . . . . . 139,142 Engine Temperature Warning . . . . . . . . . . . . . . 175 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 123,181,389 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 121 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Malfunction Indicator Light (Check Engine) . . 181,350 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 414 Manual Transaxle . . . . . . . . . . . . . . . . . . 239,242,374 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . 243 Fluid Level Check . . . . . . . . . . . . . . . . . . . 374,375 Frequency of Fluid Change . . . . . . . . . . . . 375,376 Lubricant Selection . . . . . . . . . . . . . . . . . . 374,375 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . .
428 INDEX Materials Added to . . . . . . . . . . . . . . . . . . . . . 355 Recommendation . . . . . . . . . . . . . . . . . . . 354,395 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . 173 Onboard Diagnostic System . . . . . . . . . . . . . . 349,350 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 142 Operator Manual (Owner’s Manual) . . . . . .
INDEX Programmable Electronic Features . . . . . . . . . . . . 187 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 22 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 295 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 193 Radio, Navigation . . . . . . . . . . . . . . . . . . . . . . . 217 Radio Operation . . . . . . . . . . . . . . . . . . . 195,203,226 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . .
430 INDEX Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 70 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 71 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 413 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 283 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . 217,220 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 223 Schedule, Maintenance . . . .
INDEX Setting the Clock . . . . . . . . . . . . . . . . 195,197,205,218 Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 187 Shift Speeds, Manual Transaxle . . . . . . . . . . . . . . 243 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Side Window Demisters (Defrosters) . . . . . . . . . . 234 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . .
432 INDEX Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 64 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 18 Theft System (Security Alarm) . . . . . . . . . . . . . . . 18 Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . 160 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 130 Tire and Loading Information Placard . . . . . . . . . 287 Tire Identification Number (TIN) . . . . . . . . . . . . . 286 Tire Markings . . . . . . . . . . . . . . . . . . . . .
INDEX Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . . 95 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 317 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 328 Hitches . . . . .
434 INDEX Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 311 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . . 370 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 191 Vehicle Identification Number (VIN) . . . . . . . . . . . . 7 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 288,317 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 8 Vehicle Storage . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2008 Patriot 2008 OWNER’ S MANUAL 81-326-0812 Third Edition Printed in U.S.A.
