Instructions / Assembly

ManualsBrandsJELD-WEN ManualsHardwareWindow Vinyl Interior Flat Trim

Installation Instructions

for Vinyl Windows without Nailing Fin (JII011)

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for vinyl windows without

an integral nail n (including nless, applied/non-integral ush

n and ange). Not all window types may be installed into every

wall condition in all areas. Consult your local building code ofcial

for applicable building codes and regulations. Local building code

requirements supersede recommended installation instructions. Areas

such as Florida and the Texas TDI region have different anchoring

requirements based on product certication. For information on

specic products, visit www.oridabuilding.org or www.tdi.texas.

gov and follow the anchoring schedule given in the drawings for the

product instead of the anchoring schedule in this document.

Double Hung

Casement

Single Hung (Tilt)

Picture Awning

Horizontal Slider

Single Hung (Side Load)

Summary of content (13 pages)

PAGE 1
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s recommended installation instructions for vinyl windows without an integral nail fin (including finless, applied/non-integral flush fin and flange). Not all window types may be installed into every wall condition in all areas. Consult your local building code official for applicable building codes and regulations.
PAGE 2
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 7 STEP INSTALLATION STICKER The 7 Installation Steps below are included with the product: 1. Inspect Product: Products should be inspected for shipping damage, color, configuration, handing, etc. Additionally, inspect products for any manufacturing anomalies prior to installation (e.g. warp, bow, squareness). Contact Dealer or JELD-WEN if issues are identified. 2. Inspect Rough Opening (R.O.): Inspect R.O.
PAGE 3
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) IMPORTANT INFORMATION | TABLE OF CONTENTS | GLOSSARY PLEASE NOTE: Installations where the sill is higher than 35 feet above ground level, or any product installation into a wall condition not specifically addressed in these instructions, must be designed by an architect or structural engineer.
PAGE 4
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) MATERIALS AND TOOLS JELD-WEN exterior window and door products should be installed in accordance with JELD-WEN’s recommended installation instructions, which are printed on the product label or can be found on our website: www.jeld-wen.com.
PAGE 5
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 2 INSPECT ROUGH OPENING (R.O.) • Verify the width and height of the rough opening is 1/2" larger than the window width and height. Openings for mulled units should be 3/4" larger than the window width and height. • Verify the rough opening Verify Square, Level and Plumb is square. The (A) and (B) measurements should be the same. Suggested deviation from square is no more A than 1/4".
PAGE 6
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 3 INSTALL SILL PAN Prepare/Shim the Sill 1. Install a sill pan in a weatherproof manner on the rough sill (refer to ASTM 2112 for types of sill pans). Always allow water to drain out of the pan and onto the building wrap, drainage plane or to the exterior. NOTE: If using a rigid sill pan, apply a continuous bead of sealant to the interior of the upturned leg of the sill pan. 2.
PAGE 7
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 4 TEMPORARILY FASTEN AND SHIM PRODUCT (CONTINUED) • Add additional shims as necessary to ensure proper alignment of the window frame. Larger windows usually need additional shims. Shims can be secured with sealant or adhesive. NOTE: Shims should be cut back 1/4" - 1/2" from the interior face of the main window frame.
PAGE 8
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 5 FASTEN PRODUCT (SIZE AND SPACING) (CONTINUED) A.) FASTEN THROUGH FRAME: 1. Use a pencil to mark the screw locations on the window frame as defined in the “Fastener Location Table”. 2. At each screw location drill a 3/8" clearance hole through the first wall of the frame only. DO NOT drill through the outer wall of the window frame. Picture (PG35) 3" - 6" 3" - 6" 1/4"max.
PAGE 9
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) FASTEN PRODUCT (SIZE AND SPACING) (CONTINUED) Single-Hung Tilt (PG35) 3" - 6" 3" - 6" 1/4"max. thick Interlock 18" OC max. 18" OC max. Jamb 3/8" Clearance hole 1/4" Sealant Jamb gap Cutaway From Head 3" - 6" 3" - 6" 1/4"max. thick Interlock 18" OC max. 3/8" Clearance hole* Jamb 3/8" Clearance hole* 18" OC max.
PAGE 10
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 5 FASTEN PRODUCT (SIZE AND SPACING) (CONTINUED) 4. Inspect the window for square, level, plumb and twist (Reference the Product Installation Tolerance Table). 5. Repeat the steps above for each installation clip. 6. For products with a rating of PG 50 refer to “Special Fastening Requirements”. Install clips are not meant to be used on WZ3Impact product. 7. Once the window is secured proceed to Section 6 – Install Drip Cap C.
PAGE 11
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 5 FASTEN PRODUCT (SIZE AND SPACING) (CONTINUED) Special Fastening Requirements For PG50 OR ABOVE Tilt Hung Windows ONLY 1. From the interior, just Double-Hung Jamb Cutaway from Top above the interlock Opposing (where the sashes meet shims at center), align with shims and drill a 3/8" 3/8" clearance hole through clearance Screw ONLY the first wall of hole the interior jamb (as Framing shown).
PAGE 12
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) 6 INSTALL DRIP CAP NOTE: A drip cap is required for all vertically mulled units and recommended for all products. 1. Apply a continuous bead of sealant to the top of the window frame. See drawing. 2. Position the drip cap on top of the window frame and seat into position with the aid of a wooden block and hammer or nonmarring mallet.
PAGE 13
Installation Instructions for Vinyl Windows without Nailing Fin (JII011) Please visit jeld-wen.com for warranty and care and maintenance information. Thank you for choosing ©2021 JELD-WEN, Inc. This publication and its contents are owned by or licensed to JELD-WEN, Inc. or its affiliates or third parties, and are protected by copyright, trademark, and other laws. Unauthorized use or duplication is prohibited. JELD-WEN reserves the right to change product specifications without notice.