Operating Guide
PRODUCT GUIDE
Aluminum Single-Hung Windows (JPG002)
SASH REMOVAL & INSTALLATION - CONTINUED
SPIRAL BALANCE - CONTINUED
0QFOXJOEPXBMMUIF
way; this releases
most of the tension
in the balance
springs.
"EFRVBUFMZTVQQPSU
the sash until
fully removed or
reinstalled.
*OTFSUUIFBEKVTUNFOU
tool into the small
hole on the bottom
of the spiral rod.
1VMMUIFTQJSBMSPE
EPXOBCPVUBOE
slowly allow the rod
to unwind. Repeat
for the opposite side.
9. Lower the sash to the bottom and remove the screw from the top of
one of the balances. Remove the balance.
4MJEFUIFTBTIUPUIFTBNFTJEFUIFCBMBODFXBTSFNPWFEBOE
remove sash.
Installation
*OTUBMMOFXMPDLPOUPTBTIJGUIFMPDLXBTCSPLFOPSUIFTBTIEPFTOhU
have a lock already installed.
4MJEFUIFBQQSPQSJBUFTJEFPGUIFTBTIJOUPUIFKBNCUIBUIBTUIF
balance still attached.
*OTFSUPQQPTJUFTJEFPGTBTIJOUPKBNC
4. Push sash up into open position.
4MJEFCBMBODFJOUPUIFHSPPWFCFUXFFOUIFTBTIBOEKBNCVOUJMUIF
bottom of the balance is ush with bottom of sash.
6TFUIFCBMBODFBEKVTUNFOUUPPMBOEUVSOUIFSPEDMPDLXJTFTJY
complete turns and reattach to the bottom corners of the sash.
Repeat for opposite side.
7. Snap guide blocks into place and attach them with screws.
0QFODMPTFBOEMPDLXJOEPXJGTBTIEPFTOPUGVODUJPOQSPQFSMZZPV
NBZOFFEUPSFBEKVTUUIFCBMBODFXJUIUIFCBMBODFBEKVTUNFOUUPPM
If sash still does not function properly, remove and reinstall.
FIXED SASH
These steps only apply to windows with a xed upper sash. They do not
apply to direct set glass.
Removal
3FNPWFPQFSBUJOH
sash as noted
above.
2. From the exterior,
remove screws
located on the
bottom rail of the
xed sash.
4MJEFTBTIEPXOIBMG
way.
4. Push sash toward
POFTJEFKBNCVOUJM
it is clear of the
PQQPTJUFTJEFKBNC
and remove sash.
Installation
To install, reverse
removal steps as noted
above.
BALANCE REPLACEMENT & ADJUSTMENT
A balance system controls the movement of a sash in a single-hung
window. Balance systems are under tension; replace with caution. If
you need help determining if the window needs a new balance, call
our service department. Order the same balance type and specify the
sash size. Balances are designed to support different sash sizes. A large
sash requires a different balance than a smaller sash. A properly tting
balance will be the correct length, hold the sash weight, and t with all
other components. If a balance needs to be replaced, we recommend
replacing all balances in the window at the same time. Read and
understand all instructions before beginning.
There are two types of balance systems; block and tackle, and spiral.
The block and tackle t
balance is encased in
a metal sleeve and
used on windows
with metal take-
out clips in the side
KBNCT5IFTFCBMBODFT
BSFOPUBEKVTUBCMF
and may have slight
differences.
The spiral balance t
is a spiral-shaped
rod extending
from a steel tube
down into a clip
attached to the sash.
Spiral systems are
BEKVTUBCMFBOENBZ
CFBEKVTUFEJGOPU
operating properly.
Spiral systems must
CFBEKVTUFEXIFO
replaced for proper
operation.
Fixed sash
attachment
screws
Balance
clip
Balance rod
"EKVTUNFOUUPPM
Sash
Block & Tackle
Balance
Spiral Balance