Instructions / Assembly

ManualsBrandsJELD-WEN ManualsDoors & Windows24 in. x 24 in. V-2500 Series Bronze FiniShield Vinyl Fixed Octagon Geometric Window with Colonial Grids/Grilles

Installation Instructions

for Vinyl Windows with Integral Nailing Fin (JII001)

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for Vinyl windows with an

integral nail n. Not all window types may be installed into every

wall condition in all areas. Consult your local building code ofcial

for applicable building codes and regulations. Local building code

requirements supersede recommended installation instructions.

JELD-WEN does not endorse the installation of our products into a

barrier-type install system unless a sill pan is present, incorporated

with through-wall ashing and can drain to the exterior (along with

other “required” components). Failure to do so may result in the denial

of any warranty claims. Areas such as Florida and the Texas TDI region

have different anchoring requirements based on product certication.

For information on specic products, visit www.oridabuilding.org

or www.tdi.texas.gov and follow the anchoring schedule given in

the drawings for the product instead of the anchoring schedule in

this document.

Double Hung

Casement

Single Hung (Tilt)

Picture Awning

Horizontal Slider

Single Hung (Side Load)

Summary of content (10 pages)

PAGE 1
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s recommended installation instructions for Vinyl windows with an integral nail fin. Not all window types may be installed into every wall condition in all areas. Consult your local building code official for applicable building codes and regulations. Local building code requirements supersede recommended installation instructions.
PAGE 2
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION | TABLE OF CONTENTS | GLOSSARY JELD-WEN does not endorse the installation of our products into a barrier-type install system unless a sill pan is present, incorporated with through-wall flashing and can drain to the exterior (along with other “required” components).
PAGE 3
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) MATERIALS AND TOOLS JELD-WEN exterior window and door products should be installed in accordance with JELD-WEN’s recommended installation instructions, which are printed on the product label or can be found on our website: www.jeld-wen.com. NOTE: When using flashing, spray adhesive/primer, sealant and foam products, we recommend using the same manufacturer and verifying compatibility.
PAGE 4
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 2 INSPECT ROUGH OPENING (R.O.) The use of a sill pan and other barriers will decrease the rough opening height clearance. Adjust the opening dimensions accordingly. This installation guide only addresses masonry/block wall, sheathed wall, open-stud construction and exterior foam insulation.
PAGE 5
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 3 INSTALL SILL PAN FLASHING SYSTEM Prepare Sill 1. A pan flashing system (as defined in ASTM E2112) is required at the sill prior to window/door product installation. Always allow water to drain out of the pan and onto the building wrap, drainage plane or to the exterior. 2. Apply a continuous bead of sealant to the interior of the upturned leg and end dams of the sill pan (if using a rigid sill pan).
PAGE 6
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 4 TEMPORARILY FASTEN AND SHIM PRODUCT To avoid injury, use at least 2-people to install. Adequately support the window until completely fastened. 1. Run a continuous 3/8" bead of sealant around the interior side of the nail fin, on both side jambs and head. A discontinuous bead of sealant should be applied at the bottom nail fin to allow for drainage. 2. Place the window onto the shims and tilt into the rough opening.
PAGE 7
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 5 FASTEN PRODUCT (SIZE AND SPACING) Common Window Fastening Fastener Spacing Table Areas such as Florida and the Texas TDI region have different anchoring requirements based on product certification. For information on specific products, visit www.floridabuilding.org or www.tdi.texas.gov and follow the anchoring schedule given in the drawings for the product instead of the anchoring schedule in this document.
PAGE 8
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 5 FASTEN PRODUCT (SIZE AND SPACING) (CONTINUED) Special Fastening Requirements For PG50 OR ABOVE Tilt Hung Windows Only 1. From the interior, just above the interlock (where the two sash meet), align with shims and drill a 3/8" clearance hole through ONLY the first wall of the interior jamb (as shown). This will allow the screw head to pass through.
PAGE 9
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 6 INSTALL DRIP CAP NOTE: A drip cap is required for all vertically mulled units and recommended for all products. 1. Apply a continuous bead of sealant to the top of the window frame. See drawing. 2. Position the drip cap on top of the window frame and seat into position with the aid of a wooden block and hammer or nonmarring mallet.
PAGE 10
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 8 REMOVE PROTECTIVE FILM After Installation If applicable, remove any protective film immediately from all surfaces of the frame/sash and within six months from any glass. • Ensure weep holes/channels are clear of debris for proper water drainage. Do not seal weep holes/channels. • Leave an expansion/contraction gap of approximately 3/8" between the window frame and final exterior wall surface (siding, stucco, etc.).