Use and Care Guide

Care and Maintenance
Wood Windows and Patio Doors (JCM003)
12/28/188
Wood window care includes proper nishing and maintenance of wood and cleaning and caring for metal clad surfaces. Bi-annual inspections are
sufcient for most areas; however, coastal areas require monthly inspections because of moisture and salt in the air.
CAUTION! Do not allow petroleum-based products to come in
contact with hardware and weatherstrip. Do not use acetone
and paint removers on coated aluminum clad surfaces. They
may remove coatings.
These solvents may be used to clean non water-soluble debris from
coated aluminum clad surfaces. Use only in small, inconspicuous
areas rst.
Alcohols:
Try these least strong solvents rst for non water-soluble debris.
• Denatured alcohol (ethanol)
• Isopropyl (rubbing alcohol)
• Methanol (wood alcohol)
Petroleum solvents and turpentine:
Especially helpful in removing grease, sealants or some
caulkingcompounds.
• VMandP naphtha
• Mineral spirits
• Kerosene
• Turpentine (wood or gum spirits)
Ketones, esters and lacquer thinner:
Use with extreme caution. Limit contact to one minute.
• Lacquer thinner
• Methyl ethyl ketone (MEK)
Chemical solutions:
Especially helpful in removing rust and masonry grout or concrete
stains. Limit contact to ve minutes. Thoroughly rinse with water.
Acid solutions are corrosive. Mix one part to ten parts water.
• Sodium hypochlorite solution (laundry bleach)
• Acetic acid (vinegar)
• Hydrochloric acid (muriatic acid)
For more information, contact a paint professional.
CLEANING WOOD SURFACES AND CLADDING
Exposed Wood Surfaces
Clean exposed wood surfaces with mild soap and water. For stubborn
residue or mildew, consider lightly sanding and renishing, or contact a
paint professional for recommendations.
Renish cracks or voids immediately.
Copper Cladding
JELD-WEN copper clad products and components will naturally change
color and appearance over time due to exposure to the environment.
Depending upon the products’ specic exposure, differences in
appearance may occur in the same structure. Repair or replacement of
products may also result in variations between original and replacement
parts. JELD-WEN is not responsible for any variations in appearance of
copper parts.
Wear cotton gloves during installation or servicing to avoid ngerprints
on copper surface. If ngerprints do occur and the following
recommendations for cleaning do not remove them, call us forassistance.
Maintenance and Cleaning
To maintain an aged look, no maintenance is required except for
occasional cleaning of surface debris with mild soap and water. For
heavier cleaning, follow the same cleaning instructions for aluminum
cladding. Do not use any solvents or cleaners that contain ammonia,
salts or oxides.
Oxidation Removal
For a shiny, non-oxidized copper appearance, try removing the oxidation
with a baking soda/water solution. A non-abrasive paste cleaner may
also work. Always test in an inconspicuous area rst, and read the
manufacturer’s label for instructions.
Aluminum Cladding
Aluminum cladding offers durability and excellent resistance against
cracking, blistering and aking under normal use. When properly
maintained, aluminum clad products will remain attractive for many years.
For general cleaning, use mild soap andwater.
Aluminum cladding usually does not require painting or nishing;
however, we offer special touch-up paints to repair scratches. Please call
us to order. We do not recommend attempting to paint larger areas due to
paint compatibility, environmental concerns, and the need to disassemble
the product for proper nishcoverage.
Clad surfaces exposed to sunlight are subject to chalking which may cause
color-fading. This is a natural process that occurs over time, even with
proper maintenance. Certain chalking or fading and damage to exterior
cladding from acid rain, salt air or other corrosive elements may not be
covered under the manufacturer’swarranty.
Aluminum Cladding – Continued
Moderate to Heavy Non Water-Soluble Cleaning
Some solvents are acceptable for removing heavy soils (e.g. oil, grease,
sealants, dried concrete stains, tar, rust and grafti). See the following
Solvent Recommendations. After using solvents, clean area with mild soap
and water to remove traces of remainingsolvent.
NOTE: Do not use solvent on painted surfaces other than metal
cladding or damage may result.
Solvent Recommendations for Aluminum Cladding