Installation Guide

ManualsBrandsJELD-WEN ManualsPatio DoorsV-2500 Clear Glass White Vinyl Left-Hand Sliding Double Door Sliding Patio Door with Screen (Common: 96-in x 80-in; Actual: 95.5-in x 79.5-in)

01/17/20191

Installation Instructions

for Vinyl Patio Doors with Integral Nailing Fin (JII006)

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for Vinyl Patio Doors with an

Integral Nailing Fin. Not all patio door types may be installed into

every wall condition in all areas. Consult your local building code

ofcial for applicable building codes and regulations. Local building

code requirements supersede recommended installation instructions.

Areas such as Florida and the Texas TDI region have different anchoring

requirements based on product certication. For information on

specic products, visit www.oridabuilding.org or www.tdi.texas.gov

and follow the anchoring schedule given in the drawings for the

product instead of the anchoring schedule in this document.

Sliding Patio Door

Summary of content (8 pages)

PAGE 1
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s recommended installation instructions for Vinyl Patio Doors with an Integral Nailing Fin. Not all patio door types may be installed into every wall condition in all areas. Consult your local building code official for applicable building codes and regulations. Local building code requirements supersede recommended installation instructions.
PAGE 2
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) IMPORTANT INFORMATION | TABLE OF CONTENTS | GLOSSARY PLEASE NOTE: Installations where the sill is higher than 35 feet above ground level, or any product installation into a wall condition not specifically addressed in these instructions, must be designed by an architect or structural engineer.
PAGE 3
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) MATERIALS AND TOOLS Provided Materials • 4- #10 x 2 1/2" screws (to secure the strike plate). Needed Materials NOTE: JELD-WEN exterior window and door products should be installed in accordance with JELD-WEN’s recommended installation instructions, which are printed on the product label or can be found on our website: www.jeld-wen.com.
PAGE 4
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 2 INSPECT ROUGH OPENING (R.O.) • Verify the width and height of the rough opening is 1/2"- 5/8" larger than the patio door width and height. Openings for mulled units should be 3/4" larger than the patio door width and height. • Verify the rough opening Verify Square, Level and Plumb is square. The (A) and (B) measurements should be the same. Suggested deviation from square is no more A than 1/4".
PAGE 5
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 3 INSTALL SILL PAN Prepare Sill 1. Install a sill pan in a weatherproof manner on the rough sill (refer to ASTM 2112 for types of sill pans). Always allow water to drain out of the pan and onto the building wrap, drainage or to the exterior. NOTE: Sill pans for stepdown landings will have a folded down edge in the front to accept the stepdown landing. 2.
PAGE 6
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 5 FASTEN PRODUCT (SIZE AND SPACING) Common Patio Door Fastening Areas such as Florida and the Texas TDI region have different anchoring requirements based on product certification. For information on specific products, visit www.floridabuilding.org or www.tdi.texas.gov and follow the anchoring schedule given in the drawings for the product instead of the anchoring schedule in this document.
PAGE 7
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 8 COMPLETE INSTALLATION Patio Door Adjustment Installation Instructions for 4-Panel Vinyl Patio Doors Roller Adjustment NOTE: Adjusting door too high may allow water and air leakage. Adjust rollers just high enough to clear sill track and still roll smoothly. 1. Builders doors have an adjustment screw on each lower end of the operating panel(s).
PAGE 8
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) Finish Installation NOTE: The shoot bolt only has 7/16" of adjustment. d. When the desired height is Sleeve achieved, replace the sleeve and screw. Shoot bolt 9. Reinstall the inactive panel back into the frame and re-adjust the rollers as necessary. 10. Check door for proper operation. 11. Adjust the keeper as necessary by loosening the four screws and sliding up or down until the lock engages properly. Tighten all screws.