Owner's manual

ManualsBrandsJELD-WEN ManualsFor HomePDS013 Custom Sliding Patio Doors

This document explains how to properly assemble a knock down (unassembled) patio door frame. Follow the installation instructions that

came with the product and this supplment to properly install the patio door.

SAFETY









• Highqualitysiliconesealant

• Phillipsscrewdriver



Do-It-Yourself

Technician



The advice offered herein should be reviewed and performed by a trained service provider. It is recommended that you consult with a competent and licensed

construction contractor or building professional prior to taking any action. JELD-WEN disclaims any and all liability associated with the use and/or provision of these

instructions. Any reliance upon the information or advice is at the risk of the party so relying. The information contained herein may be changed from time to time

without notication.

All other trademarks are the property of their respective owners.

Sill

RubberBumperat

HeadJamb

SideJamb

RubberBumperatSill

Track

HeadJamb

ExteriorSideFiller/

ExteriorHeadFiller

CladExtrusionGasket

UpperPanelTrack(sits

ontopofoperating

panel)

RectangularGasket

InteriorStationarySide

Filler

CornerKeys

InteriorHeadStop







(1)Sill

(2)Sidejambs

(1)Headjamb

(2)Cornerkeys

(2)Cladextrusiongaskets

(2)Rectangulargasket



(1)Operatingpanel

(1)Stationarypanel

(1)Upperpaneltrack

(1)Interiorstationarysideller

(2)Exteriorllers

(1)Interiorheadstop

(1)Pileweatherstrippad

(1)Rubberbumper

(1)Handleset



(21) #8x3/4"screwsforframeassembly

(1) #8x3/4"screw-tosecurexedpanelclip

(15) #7x3/4"screws-tosecureexteriorllers

(4) #7x3/4"screws-tosecurestat.panelatsill

(8) #7x3/4"screws-tosecureupperpaneltrack

(10) 11/4"nails-tosecureinteriorstat.sideller

(1) #6x11/2"screws-tosecurerubberbumper

Summary of content (3 pages)

PAGE 1
c u s t o m Sl i d i n g Pati o Do o rs Supplemental A s s em b ly In s tru c t i o n s This document explains how to properly assemble a knock down (unassembled) patio door frame. Follow the installation instructions that came with the product and this supplment to properly install the patio door. SAFETY • Read and fully understand ALL manufacturers’ instructions before beginning. • Patio doors can be very heavy and awkward. Do not work alone. Two or more people are required. Use safe lifting techniques.
PAGE 2
Assemble Frame The frame is already handed and is not field reversible. 1. Lay out frame components (exterior side up) in a large, flat workspace. 2. On the sill piece, apply a continuous bead of silicone at each end as shown. Sill 3. Seal the top of Side jamb top each side jamb piece as follows: • Place the clad extrusion gasket on the open end of the clad Clad Rectangular gasket extrusion as extrusion shown.
PAGE 3
Install Stationary Panel 7. Place the pile weatherstrip pad on the operating side jamb where it meets the sill. This pad is critical to preventing air infiltration. 1. From the exterior, install the stationary panel into the exterior frame track as follows: • Tip the panel into the header track. • Swing the bottom of the Stationary panel up and panel over the sill track. • Slide the panel tightly up against the side jamb. 2.