Full Product Manual

2
PRODUCT GUIDE
Vinyl Patio Doors (JPG008)
NEEDED TOOLS
Note! Each tool is not required for every task.
• Phillips head screwdriver
• Allen wrenches
• Tape measure
• 2' or 4' Level
• Putty knife
• Follow all manufacturers’ instructions and labels.
• Use proper and safe equipment and precautions when cleaning and
servicing the exterior side of patio doors above ground level.
• Insect screens are not security devices and will not prevent a child,
other person, or pet from falling through.
• Use extra care when driving screws near glass unit to avoid breakage.
• Use caution when tightening screws to avoid stripping the
screwholes.
• Panel removal can be awkward and could cause physical injury or
product damage; we recommend the help of a second person.
PRECAUTIONS AND SAFETY
TOOLS AND MATERIALS
SLIDING SCREEN AND PANEL REMOVAL AND INSTALLATION
NEEDED MATERIALS
• String
• Tape
SLIDING INSECT SCREEN REMOVAL, INSTALLATION & ADJUSTMENT
It may be helpful to
remove insect screen
before other panel(s).
Adjustment screws are
located at each corner
of the door screen and
may be located on
the end of the screen
or on the face. Face
adjustment screws
can either be on top
of the lower rail or
accessed through a hole
asshown.
1. Turn all four adjustment screws to retract rollers into the screen.
Note! If door screen has weatherstrip covering adjustment screw,
pull out only enough to expose screw, then press back into place
afteradjustment.
2. Grip both sides of the screen and lift up and over the screen track (if
needed, use putty knife to help lift rollers over track) and remove.
Installation
1. Thoroughly clean sill track and head frame channel. The sill can be
lightly lubricated with silicone if necessary.
2. Turn all four adjustment screws to retract rollers into the screen.
3. Orient the screen so the nger lever on the screen latch faces
theinside.
4. Grip both sides of the screen and lift up and over the screen track (if
needed, use putty knife to help lift rollers over track) and remove.
5. Adjust the rollers as explained below.
Roller Adjustment
1. Ideal adjustment is as low as possible but just high enough to avoid
drag. Adjustment screws are located at each corner of the door
screen. Turn the adjustment screw in quarter turn increments until
the correct adjustment is achieved. Some rollers will require opposing
rotations to move the roller in the same direction as the other rollers.
• If screen door is ush to side jamb but needs to be raised or
lowered, adjust both bottom rollers the same amount and in the
same direction. Adjust top rollers if needed to apply slight tension.
• If screen top touches side jamb rst, extend the roller closest to the
side jamb, and retract the roller farthest from the side jamb. Make
opposite adjustments if the screen bottom touches side jamb rst.
2. Test operation and readjust as needed.
SLIDING/ROLLING PATIO DOORS
Panel removal can be awkward and could cause physical injury or
product damage; we recommend the help of additional people.
OPERATING PANEL REMOVAL - FOR PROFESSIONALS ONLY
Operating panel(s) normally remove to the interior. Some doors have
a sill riser that will prevent the panel from being removed to the
interior. The xed panel(s) will need to be removed and the operating
panel will then be removed to the exterior. Follow the instructions for
xed panel removal, if necessary, before attempting to remove the
operatingpanel(s).
1. On the interior,
unlock panel and
slide to the middle
or further past the
anti-lift blocks in
thehead.
2. Lift panel up and
over bottom track
and remove to the
interior. The rollers
may need to be
adjusted up into the
panel and then held
with a putty knife
or similar at tool
in order to clear the
silltrack.
INSTALLATION
To install, reverse removal steps.
End Adjusted Roller
Face Adjusted Roller
Adjustment Screw
Locations
05/20