Instructions / Assembly

ManualsBrandsJELD-WEN ManualsDoors & Windows72 in. x 80 in. V-4500 Contemporary Black Painted Vinyl Right-Hand Full Lite Sliding Patio Door w/White Interior

Table Of Contents

Installation Instructions

for Vinyl Patio Doors with Integral Nailing Fin (JII006)

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for Vinyl Patio Doors with an

Integral Nailing Fin. Not all patio door types may be installed into

every wall condition in all areas. Consult your local building code

ofcial for applicable building codes and regulations. Local building

code requirements supersede recommended installation instructions.

JELD-WEN does not endorse the installation of our products into a

barrier-type install system unless a sill pan is present, incorporated

with through-wall ashing and can drain to the exterior (along with

other “required” components). Failure to do so may result in the denial

of any warranty claims. Areas such as Florida and the Texas TDI region

have different anchoring requirements based on product certication.

For information on specic products, visit www.oridabuilding.org

or www.tdi.texas.gov and follow the anchoring schedule given in

the drawings for the product instead of the anchoring schedule in

this document.

Sliding Patio Door

2 Panel

3 Panel

4 Panel

A minimum of 2-people will be

needed to assemble and safely

move door units.

Summary of content (12 pages)

PAGE 1
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s recommended installation instructions for Vinyl Patio Doors with an Integral Nailing Fin. Not all patio door types may be installed into every wall condition in all areas. Consult your local building code official for applicable building codes and regulations. Local building code requirements supersede recommended installation instructions.
PAGE 2
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 8 STEP INSTALLATION STICKER The 8 Installation Steps below are included with the product: 1. Inspect Product: Products should be inspected for shipping damage, color, configuration, handing, and correct size, as well as for any manufacturing anomalies prior to installation (e.g., warp, bow, squareness). Contact your Dealer or JELD-WEN if any issues are identified. 2.
PAGE 3
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) IMPORTANT INFORMATION | TABLE OF CONTENTS | GLOSSARY JELD-WEN does not endorse the installation of our products into a barrier-type install system unless a sill pan is present, incorporated with through-wall flashing and can drain to the exterior (along with other “required” components). Failure to do so may result in the denial of any warranty claims.
PAGE 4
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) MATERIALS AND TOOLS • 4- #10 x 2 1/2" screws (to secure the strike plate, two-panel units only). • Sealant: An exterior grade sealant (e.g., OSI® QUAD® Max or equivalent) is recommended for installation practices. Check with sealant manufacturer for color-match options and paintability. • Polyurethane Low-Expansion Window and Door Foam: A lowexpansion, polyurethane window and door foam (e.g.
PAGE 5
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 2 INSPECT ROUGH OPENING (R.O.) The use of a sill pan and other barriers will decrease the rough opening height clearance. Adjust the opening dimensions accordingly. This installation guide only addresses masonry/block wall, sheathed wall, open-stud construction and exterior foam insulation.
PAGE 6
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 3 INSTALL SILL PAN FLASHING SYSTEM Landings These instructions cover two patio door sill conditions: the step-down landing and the continuous slab landing. The installation methods vary slightly between landing types. 2. Apply a continuous bead of sealant to the interior of the upturned leg and end dams of the sill pan (if using a rigid sill pan). Shim the Sill Step-Down Landing Continuous Slab Landing Prepare Sill 1.
PAGE 7
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 4 TEMPORARILY FASTEN AND SHIM PRODUCT To avoid injury, use at least 2-people to install. Adequately support the patio door until fully installed. 1. For continuous slab landings only, score and remove the nailing fin at the sill. 2. Run a continuous 3/8" bead of sealant around the interior side of the nail fin, on both side jambs and head.
PAGE 8
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 5 FASTEN PRODUCT (SIZE AND SPACING) Common Patio Door Fastening Through Sill Fastening Fasteners through the sill will breach the sill pan flashing. Following the sealant application steps outlined below is imperative. Generally, through sill fastening is not needed for two panel doors with a PG 35 or under rating. A discontinuous bead of sealant should be used to secure the door frame to the sill pan.
PAGE 9
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 6 INSTALL DRIP CAP The use of a drip cap on all window/door products is recommended, regardless if supplied. A drip cap is required on any vertical mulled/ joined products, regardless if supplied. NOTE: A drip cap may not be suitable for some product lines (e.g.
PAGE 10
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 8 REMOVE PROTECTIVE FILM Patio Door Adjustment Installation Instructions for 4-Panel Vinyl Patio Doors Roller Adjustment: NOTE: Adjusting door too high may allow water and air leakage. Adjust rollers just high enough to clear sill track and still roll smoothly. 1. Builders doors have an adjustment screw on each lower end of the operating panel(s).
PAGE 11
Installation Instructions for Vinyl Patio Doors with Integral Nailing Fin (JII006) 8 REMOVE PROTECTIVE FILM Lock Adjustment Patio door panels are very heavy. Removal and installation require two or more people. Shoot Bolt Height Adjustment: • Remove the inactive panel from the door frame. The rollers may need to be adjusted up into the panel to clear the sill track. Slide the panel to an open position and lift it up and over the sill track. • Place the door on sawhorses.
PAGE 12
Installation Instructions for Vinyl Windows with Integral Nailing Fin (JII001) 8 REMOVE PROTECTIVE FILM Anchor Fastening Install Bumper 1. For 2-panel door systems, drive two #10 x 2 1/2" screws through the open screw holes in the strike plate (included in the hardware pack). NOTE: Screws should penetrate through the door frame, shims and embed into a rough framing member. 2. Shut the door and test for locking capability.